diff options
Diffstat (limited to 'keyboards/mechmini/v1')
| -rw-r--r-- | keyboards/mechmini/v1/README.md | 80 |
1 files changed, 8 insertions, 72 deletions
diff --git a/keyboards/mechmini/v1/README.md b/keyboards/mechmini/v1/README.md index 315349803a..902948c24d 100644 --- a/keyboards/mechmini/v1/README.md +++ b/keyboards/mechmini/v1/README.md @@ -1,83 +1,19 @@ -Mechmini V1 -=========== +# Mechmini V1 A 40% ortholinear/staggered keyboard, that was originally bootmapper and can be ported to QMK following this readme. This version is no longer in production [More info on MECHKEYS](https://mechkeys.ca). -Keyboard Maintainer: QMK Community -Hardware Supported: Mechmini 1 PCB -Hardware Availability: Version 1 (Bootmapper) no longer in production [MECHKEYS](https://mechkeys.ca) +* Keyboard Maintainer: QMK Community +* Hardware Supported: Mechmini 1 PCB +* Hardware Availability: Version 1 (Bootmapper) no longer in production [MECHKEYS](https://mechkeys.ca) Make example for this keyboard (after setting up your build environment): make mechmini/v1:default -See [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) then the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. +Flashing example for this keyboard ([after setting up the bootloadHID flashing environment](https://docs.qmk.fm/#/flashing_bootloadhid)) -## Mechmini Notes - -Note that this is a complete replacement for the firmware, so you won't be -using Bootmapper Client to change any keyboard settings, since not all the -USB report options are supported. - -## Installing - -First, install the requirements. These commands are for OSX, but all you -need is the AVR toolchain and `bootloadHID` for flashing: - -``` -$ brew cask install crosspack-avr -$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb -``` - -In order to use the `./util/atmega32a_program.py` script, which can reboot the board into -the bootloader, you'll need Python 2 with PyUSB installed: - -``` -$ pip install pyusb -``` - -Then, with the keyboard plugged in, simply run this command from the -`qmk_firmware` directory: - -``` -$ make mechmini:program -``` - -If you prefer, you can just build it and flash the firmware directly with -`bootloadHID` if you boot the board while holding down `L_Ctrl` to keep it -in the bootloader: - -``` -$ make mechmini -$ bootloadHID -r mechmini_default.hex -``` - -## Troubleshooting - -From my experience, it's really hard to brick these boards. But these -tricks have been useful when it got stuck in a weird scenario. - -1. Try plugging the board in while pressing `L_Ctrl`. This will force it - to boot only the bootloader without loading the firmware. Once this is - done, just reflash the board with the original firmware. -2. Sometimes USB hubs can act weird, so try connecting the board directly - to your computer or plugging/unplugging the USB hub. -3. If errors happen with -`./tmk_core/common/avr/suspend.c` it is likely you implemented a RGB underglow sleep setting previously. Simply comment out the following code found under `void suspend_wakeup_init(void)`: -``` -ifdef RGBLIGHT_ANIMATIONS - rgblight_timer_enable(); - _delay_ms(50); - rgblight_set(); -#endif -``` -So that the resulting code should know reflect: -``` -/*#ifdef RGBLIGHT_ANIMATIONS - rgblight_timer_enable(); - _delay_ms(50); - rgblight_set(); -#endif*/ -``` + make mechmini/v1:default:flash +**Reset Key**: Hold down the key commonly programmed as *L_Ctrl* while plugging in the keyboard. +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). |