1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
|
# 'serial' Driver
This driver powers the [Split Keyboard](feature_split_keyboard.md) feature.
?> Serial in this context should be read as **sending information one bit at a time**, rather than implementing UART/USART/RS485/RS232 standards.
All drivers in this category have the following characteristics:
* Provides data and signaling over a single conductor
* Limited to single master, single slave
## Supported Driver Types
| | AVR | ARM |
|-------------------|--------------------|--------------------|
| bit bang | :heavy_check_mark: | :heavy_check_mark: |
| USART Half-duplex | | :heavy_check_mark: |
## Driver configuration
### Bitbang
Default driver, the absence of configuration assumes this driver. To configure it, add this to your rules.mk:
```make
SERIAL_DRIVER = bitbang
```
Configure the driver via your config.h:
```c
#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
#define SELECT_SOFT_SERIAL_SPEED 1 // or 0, 2, 3, 4, 5
// 0: about 189kbps (Experimental only)
// 1: about 137kbps (default)
// 2: about 75kbps
// 3: about 39kbps
// 4: about 26kbps
// 5: about 20kbps
```
#### ARM
!> The bitbang driver causes connection issues with bitbang WS2812 driver
Along with the generic options above, you must also turn on the `PAL_USE_CALLBACKS` feature in your halconf.h.
### USART Half-duplex
Targeting STM32 boards where communication is offloaded to a USART hardware device. The advantage is that this provides fast and accurate timings. `SOFT_SERIAL_PIN` for this driver is the configured USART TX pin. **The TX pin must have appropriate pull-up resistors**. To configure it, add this to your rules.mk:
```make
SERIAL_DRIVER = usart
```
Configure the hardware via your config.h:
```c
#define SOFT_SERIAL_PIN B6 // USART TX pin
#define SELECT_SOFT_SERIAL_SPEED 1 // or 0, 2, 3, 4, 5
// 0: about 460800 baud
// 1: about 230400 baud (default)
// 2: about 115200 baud
// 3: about 57600 baud
// 4: about 38400 baud
// 5: about 19200 baud
#define SERIAL_USART_DRIVER SD1 // USART driver of TX pin. default: SD1
#define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
#define SERIAL_USART_TIMEOUT 100 // USART driver timeout. default 100
```
You must also enable the ChibiOS `SERIAL` feature:
* In your board's halconf.h: `#define HAL_USE_SERIAL TRUE`
* In your board's mcuconf.h: `#define STM32_SERIAL_USE_USARTn TRUE` (where 'n' matches the peripheral number of your selected USART on the MCU)
Do note that the configuration required is for the `SERIAL` peripheral, not the `UART` peripheral.
|
