diff options
Diffstat (limited to 'x68k_usb')
| -rw-r--r-- | x68k_usb/Makefile | 87 | ||||
| -rw-r--r-- | x68k_usb/README | 129 | ||||
| -rw-r--r-- | x68k_usb/config_pjrc.h | 66 | ||||
| -rw-r--r-- | x68k_usb/keymap.c | 140 | ||||
| -rw-r--r-- | x68k_usb/led.c | 26 | ||||
| -rw-r--r-- | x68k_usb/matrix.c | 141 | ||||
| -rw-r--r-- | x68k_usb/x68k.c | 75 | ||||
| -rw-r--r-- | x68k_usb/x68k.h | 47 |
8 files changed, 0 insertions, 711 deletions
diff --git a/x68k_usb/Makefile b/x68k_usb/Makefile deleted file mode 100644 index 0127c0bf84..0000000000 --- a/x68k_usb/Makefile +++ /dev/null @@ -1,87 +0,0 @@ -# -# Makefile for PJRC Teensy -# - - -# Target file name (without extension). -TARGET = x68k_usb_pjrc - -# Directory common source filess exist -TOP_DIR = .. - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# keyboard dependent files -SRC = main.c \ - keymap.c \ - matrix.c \ - led.c \ - x68k.c - -CONFIG_H = config_pjrc.h - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 - - -# Build Options -# *Comment out* to disable the options. -# -MOUSEKEY_ENABLE = yes # Mouse keys -EXTRAKEY_ENABLE = yes # Audio control and System control -NKRO_ENABLE = yes # USB Nkey Rollover - - - -#---------------- Programming Options -------------------------- -AVRDUDE = avrdude -# Type: avrdude -c ? to get a full listing. -AVRDUDE_PROGRAMMER = avr109 -AVRDUDE_PORT = /dev/ttyACM0 -AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex -#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep - -# Uncomment the following if you want avrdude's erase cycle counter. -# Note that this counter needs to be initialized first using -Yn, -# see avrdude manual. -#AVRDUDE_ERASE_COUNTER = -y - -# Uncomment the following if you do /not/ wish a verification to be -# performed after programming the device. -#AVRDUDE_NO_VERIFY = -V - -# Increase verbosity level. Please use this when submitting bug -# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> -# to submit bug reports. -#AVRDUDE_VERBOSE = -v -v - -AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) -AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) -AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) -AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) - -#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) -#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex -PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex - - - -include $(TOP_DIR)/protocol/pjrc.mk -include $(TOP_DIR)/protocol.mk -include $(TOP_DIR)/common.mk -include $(TOP_DIR)/rules.mk diff --git a/x68k_usb/README b/x68k_usb/README deleted file mode 100644 index 0b61b2c4b3..0000000000 --- a/x68k_usb/README +++ /dev/null @@ -1,129 +0,0 @@ -X68000 to USB keyboard protocol converter -========================================= -SHARP X68000 is a hobby computer released in Japan.(1987-93) -http://en.wikipedia.org/wiki/Sharp_X68000 - -X68000 keyboard has ALPS linear switches. -- DSETK0016CE01 green linear -- DSETK0023CE03 yellow linear - - -Hardware --------- -Target MCU is ATMega32u4 but other USB capable AVR will also work. -You can use PJRC Teensy as dev board. - http://www.pjrc.com/teensy/ - -Wiring: - Mini-DIN Teensy - ----------------------------------------------------- - pin1 +5V VCC - pin2 MOUSE - - pin3 RXD PD2(RXD) - pin4 TXD PD3(TXD) NOTE: Not supported yet. - pin5 READY - - pin6 REMOTE - - pin7 GND GND - - -Firmware --------- -Build: - $ cd x68k_usb - $ make - -And load the binary to MCU with your favorite programmer. -If you use Teensy you can load with PJRC Teensy Loader tool. - http://www.pjrc.com/teensy/loader.html - - -* * * * * * * * * * * * * * * * * * - - -X68000 Keyboard Protocol -======================== -http://kyoutan.jpn.org/uts/pc/pic/x68key/ - - -Connector ---------- -Mini DIN 7pin(female connector on computer side) - 7 6 5 - o o o - 4 o = o 3 - o o - 2 1 - - Mini-DIN - ------------- - pin1 +5V - pin2 MOUSE - pin3 RXD - pin4 TXD - pin5 READY - pin6 REMOTE - pin7 GND - - -Signaling ---------- -- TXD,RXD - Asynchronous, 2400baud, 1-startbit(L), 8-databit, 1-stopbit(H) - -- READY - ready/not ready(1/0) - - -Data from keyboard ------------------- -bit 7 make/break flag(0/1) -bit 6-0 following scan code - - -Data from computer ------------------- -- LED contorol ON/OFF(0/1) - bit 7 1(fixed) - bit 6 全角 - bit 5 ひらがな - bit 4 INS - bit 3 CAPS - bit 2 コード入力 - bit 1 ローマ字 - bit 0 かな - -- Repeat delay - bit 7 0(fixed) - bit 6 1(fixed) - bit 5 1(fixed) - bit 4 0(fixed) - bit 3-0 delay - REPEAT_DELAY = 200+delay*100 ms - default: 500ms - -- Repeat time - bit 7 0(fixed) - bit 6 1(fixed) - bit 5 1(fixed) - bit 4 1(fixed) - bit 3-0 time - REPEAT_TIME = 30+time^2*5 ms - default: 110ms - - -Scan Codes ----------- -,---. ,---. ,-------------------, ,-------------------. ,-----------. ,---------------. -| 61| | 62| | 63| 64| 65| 66| 67| | 68| 69| 6A| 6B| 6C| | 5A| 5B| 5C| | 5D| 52| 53| 54| -`---' `---' `-------------------' `-------------------' `-----------' `---------------' -,-----------------------------------------------------------. ,-----------. ,---------------. -| 01| 02| 03| 04| 05| 06| 07| 08| 09| 0A| 0B| 0C| 0D| 0E| 0F| | 36| 5E| 37| | 3F| 40| 41| 42| -|-----------------------------------------------------------| |------------ |---------------| -| 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| | | 38| 39| 3A| | 43| 44| 45| 46| -|------------------------------------------------------. 1D | `---=====---' |---------------| -| 71 | 1E| 1F| 20| 21| 2l| 23| 24| 25| 26| 27| 28| 29| | ___| 3C|___ | 47| 48| 49| 4A| -|-----------------------------------------------------------| | 3B|---| 3D| |-----------|---| -| 70 | 2A| 2B| 2C| 2D| 2E| 2F| 30| 31| 32| 33| 34| 70 | `---| 3E|---' | 4B| 4C| 4D| | -`-----------------------------------------------------------| .---=====---. |-----------| 4E| - | 5F| 55 | 56 | 35 | 57 | 58 | 59 | 60| | 72 | 73 | | 4F| 50| 51| | - `---------------------------------------------' `-----------' `---------------' diff --git a/x68k_usb/config_pjrc.h b/x68k_usb/config_pjrc.h deleted file mode 100644 index 20758bf249..0000000000 --- a/x68k_usb/config_pjrc.h +++ /dev/null @@ -1,66 +0,0 @@ -/* -Copyright 2012 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -/* controller configuration */ -#include "controller_teensy.h" - -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6800 -#define MANUFACTURER t.m.k. -#define PRODUCT SHARP X68000 keyboard converter -#define DESCRIPTION converts SHARP X68000 keyboard protocol into USB - - -/* matrix size */ -#define MATRIX_ROWS 16 -#define MATRIX_COLS 8 - - -/* key combination for command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KB_LALT) | MOD_BIT(KB_RALT)) || \ - keyboard_report->mods == (MOD_BIT(KB_LCTRL) | MOD_BIT(KB_RSHIFT)) \ -) - - -/* mouse keys */ -#ifdef MOUSEKEY_ENABLE -# define MOUSEKEY_DELAY_TIME 255 -#endif - - -/* USART configuration - * asynchronous, 2400baud, 8-data bit, non parity, 1-stop bit, no flow control - */ -#ifdef __AVR_ATmega32U4__ -# define KBD_RX_VECT USART1_RX_vect -# define KBD_RX_DATA UDR1 -# define KBD_RX_BAUD 2400 -# define KBD_RX_UBBR ((F_CPU/(16UL*KBD_RX_BAUD))-1) -# define KBD_RX_INIT() do { \ - UBRR1L = (uint8_t) KBD_RX_UBBR; \ - UBRR1H = (uint8_t) (KBD_RX_UBBR>>8); \ - UCSR1B |= (1<<RXCIE1) | (1<<RXEN1); \ - } while(0) -#else -# error "USART configuration is needed." -#endif - -#endif diff --git a/x68k_usb/keymap.c b/x68k_usb/keymap.c deleted file mode 100644 index 94c2aeee11..0000000000 --- a/x68k_usb/keymap.c +++ /dev/null @@ -1,140 +0,0 @@ -/* -Copyright 2012 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#include <stdint.h> -#include <stdbool.h> -#include <avr/pgmspace.h> -#include "usb_keycodes.h" -#include "util.h" -#include "keymap.h" - - - - -// Following macros help you to define a keymap with the form of actual keyboard layout. - -/* X68000 Keyboard Scan codes - ,---. ,---. ,-------------------, ,-------------------. ,-----------. ,---------------. - | 61| | 62| | 63| 64| 65| 66| 67| | 68| 69| 6A| 6B| 6C| | 5A| 5B| 5C| | 5D| 52| 53| 54| - `---' `---' `-------------------' `-------------------' `-----------' `---------------' - ,-----------------------------------------------------------. ,-----------. ,---------------. - | 01| 02| 03| 04| 05| 06| 07| 08| 09| 0A| 0B| 0C| 0D| 0E| 0F| | 36| 5E| 37| | 3F| 40| 41| 42| - |-----------------------------------------------------------| |------------ |---------------| - | 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| | | 38| 39| 3A| | 43| 44| 45| 46| - |------------------------------------------------------. 1D | `---=====---' |---------------| - | 71 | 1E| 1F| 20| 21| 2l| 23| 24| 25| 26| 27| 28| 29| | ___| 3C|___ | 47| 48| 49| 4A| - |-----------------------------------------------------------| | 3B|---| 3D| |-----------|---| - | 70 | 2A| 2B| 2C| 2D| 2E| 2F| 30| 31| 32| 33| 34| 70 | `---| 3E|---' | 4B| 4C| 4D| | - `-----------------------------------------------------------| .---=====---. |-----------| 4E| - | 5F| 55 | 56 | 35 | 57 | 58 | 59 | 60| | 72 | 73 | | 4F| 50| 51| | - `---------------------------------------------' `-----------' `---------------' -*/ -#define KEYMAP( \ - K61,K62, K63,K64,K65,K66,K67, K68,K69,K6A,K6B,K6C, K5A,K5B,K5C, K5D,K52,K53,K54, \ - K01,K02,K03,K04,K05,K06,K07,K08,K09,K0A,K0B,K0C,K0D,K0E,K0F, K36,K5E,K37, K3F,K40,K41,K42, \ - K10,K11,K12,K13,K14,K15,K16,K17,K18,K19,K1A,K1B,K1C, K1D, K38,K39,K3A, K43,K44,K45,K46, \ - K71,K1E,K1F,K20,K21,K22,K23,K24,K25,K26,K27,K28,K29, K3C, K47,K48,K49,K4A, \ - K70,K2A,K2B,K2C,K2D,K2E,K2F,K30,K31,K32,K33,K34, K3B,K3E,K3D, K4B,K4C,K4D,K4E, \ - K5F,K55,K56, K35, K57,K58,K59,K60, K72, K73, K4F,K50,K51 \ -) { \ - { KB_NO, KB_##K01, KB_##K02, KB_##K03, KB_##K04, KB_##K05, KB_##K06, KB_##K07 }, \ - { KB_##K08, KB_##K09, KB_##K0A, KB_##K0B, KB_##K0C, KB_##K0D, KB_##K0E, KB_##K0F }, \ - { KB_##K10, KB_##K11, KB_##K12, KB_##K13, KB_##K14, KB_##K15, KB_##K16, KB_##K17 }, \ - { KB_##K18, KB_##K19, KB_##K1A, KB_##K1B, KB_##K1C, KB_##K1D, KB_##K1E, KB_##K1F }, \ - { KB_##K20, KB_##K21, KB_##K22, KB_##K23, KB_##K24, KB_##K25, KB_##K26, KB_##K27 }, \ - { KB_##K28, KB_##K29, KB_##K2A, KB_##K2B, KB_##K2C, KB_##K2D, KB_##K2E, KB_##K2F }, \ - { KB_##K30, KB_##K31, KB_##K32, KB_##K33, KB_##K34, KB_##K35, KB_##K36, KB_##K37 }, \ - { KB_##K38, KB_##K39, KB_##K3A, KB_##K3B, KB_##K3C, KB_##K3D, KB_##K3E, KB_##K3F }, \ - { KB_##K40, KB_##K41, KB_##K42, KB_##K43, KB_##K44, KB_##K45, KB_##K46, KB_##K47 }, \ - { KB_##K48, KB_##K49, KB_##K4A, KB_##K4B, KB_##K4C, KB_##K4D, KB_##K4E, KB_##K4F }, \ - { KB_##K50, KB_##K51, KB_##K52, KB_##K53, KB_##K54, KB_##K55, KB_##K56, KB_##K57 }, \ - { KB_##K58, KB_##K59, KB_##K5A, KB_##K5B, KB_##K5C, KB_##K5D, KB_##K5E, KB_##K5F }, \ - { KB_##K60, KB_##K61, KB_##K62, KB_##K63, KB_##K64, KB_##K65, KB_##K66, KB_##K67 }, \ - { KB_##K68, KB_##K69, KB_##K6A, KB_##K6B, KB_##K6C, KB_NO, KB_NO, KB_NO }, \ - { KB_##K70, KB_##K71, KB_##K72, KB_##K73, KB_NO, KB_NO, KB_NO, KB_NO, }, \ - { KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO, KB_NO } \ -} - - -// Assign Fn key(0-7) to a layer to which switch with the Fn key pressed. -static const uint8_t PROGMEM fn_layer[] = { - 0, // Fn0 - 0, // Fn1 - 0, // Fn2 - 0, // Fn3 - 0, // Fn4 - 0, // Fn5 - 0, // Fn6 - 0 // Fn7 -}; - -// Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer. -// See layer.c for details. -static const uint8_t PROGMEM fn_keycode[] = { - KB_NO, // Fn0 - KB_NO, // Fn1 - KB_NO, // Fn2 - KB_NO, // Fn3 - KB_NO, // Fn4 - KB_NO, // Fn5 - KB_NO, // Fn6 - KB_NO // Fn7 -}; - - -static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { -/* X68000 Keyboard Scan codes - ,---. ,---. ,-------------------, ,-------------------. ,-----------. ,---------------. - | 61| | 62| | 63| 64| 65| 66| 67| | 68| 69| 6A| 6B| 6C| | 5A| 5B| 5C| | 5D| 52| 53| 54| - `---' `---' `-------------------' `-------------------' `-----------' `---------------' - ,-----------------------------------------------------------. ,-----------. ,---------------. - | 01| 02| 03| 04| 05| 06| 07| 08| 09| 0A| 0B| 0C| 0D| 0E| 0F| | 36| 5E| 37| | 3F| 40| 41| 42| - |-----------------------------------------------------------| |------------ |---------------| - | 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| | | 38| 39| 3A| | 43| 44| 45| 46| - |------------------------------------------------------. 1D | `---=====---' |---------------| - | 71 | 1E| 1F| 20| 21| 2l| 23| 24| 25| 26| 27| 28| 29| | ___| 3C|___ | 47| 48| 49| 4A| - |-----------------------------------------------------------| | 3B|---| 3D| |-----------|---| - | 70 | 2A| 2B| 2C| 2D| 2E| 2F| 30| 31| 32| 33| 34| 70 | `---| 3E|---' | 4B| 4C| 4D| | - `-----------------------------------------------------------| .---=====---. |-----------| 4E| - | 5F| 55 | 56 | 35 | 57 | 58 | 59 | 60| | 72 | 73 | | 4F| 50| 51| | - `---------------------------------------------' `-----------' `---------------' -*/ - KEYMAP( - NO, NO, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, PSCR,SLCK,PAUS, CAPS,NO, NO, NO, - ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSLS,BSPC, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS, - TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, ENT, DEL, END, PGDN, P7, P8, P9, PPLS, - LCTL,A, S, D, F, G, H, J, K, L, SCLN,QUOT,ENT, UP, P4, P5, P6, PEQL, - LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH,GRV, LEFT,DOWN,RGHT, P1, P2, P3, PENT, - LGUI,LALT,NO, SPC, RALT,RGUI,RCTL,APP, NO, NO, P0, PCMM,PDOT - ), -}; - - -uint8_t keymap_get_keycode(uint8_t layer, uint8_t row, uint8_t col) -{ - return pgm_read_byte(&keymaps[(layer)][(row)][(col)]); -} - -uint8_t keymap_fn_layer(uint8_t fn_bits) -{ - return pgm_read_byte(&fn_layer[biton(fn_bits)]); -} - -uint8_t keymap_fn_keycode(uint8_t fn_bits) -{ - return pgm_read_byte(&fn_keycode[(biton(fn_bits))]); -} diff --git a/x68k_usb/led.c b/x68k_usb/led.c deleted file mode 100644 index 40156cf4ac..0000000000 --- a/x68k_usb/led.c +++ /dev/null @@ -1,26 +0,0 @@ -/* -Copyright 2012 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#include "stdint.h" -#include "x68k.h" -#include "led.h" - - -void led_set(uint8_t usb_led) -{ - // not supported now -} diff --git a/x68k_usb/matrix.c b/x68k_usb/matrix.c deleted file mode 100644 index 954e7ef129..0000000000 --- a/x68k_usb/matrix.c +++ /dev/null @@ -1,141 +0,0 @@ -/* -Copyright 2012 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#include <stdint.h> -#include <stdbool.h> -#include <avr/io.h> -#include <util/delay.h> -#include "print.h" -#include "util.h" -#include "x68k.h" -#include "matrix.h" - - -/* - * Matrix Array usage: - * - * ROW: 16(4bits) - * COL: 8(3bits) - * - * 8bit wide - * +---------+ - * 0|00 ... 07| - * 1|08 ... 0F| - * :| ... | - * :| ... | - * E|70 ... 77| - * F|78 ... 7F| - * +---------+ - * - */ -static uint8_t matrix[MATRIX_ROWS]; -#define ROW(code) ((code>>3)&0xF) -#define COL(code) (code&0x07) - -static bool is_modified = false; - - -inline -uint8_t matrix_rows(void) -{ - return MATRIX_ROWS; -} - -inline -uint8_t matrix_cols(void) -{ - return MATRIX_COLS; -} - -void matrix_init(void) -{ - x68k_init(); - - // initialize matrix state: all keys off - for (uint8_t i=0; i < MATRIX_ROWS; i++) matrix[i] = 0x00; - - return; -} - -uint8_t matrix_scan(void) -{ - is_modified = false; - - uint8_t code; - code = x68k_recv(); - if (code == 0) { - return 0; - } - - phex(code); print(" "); - if (code&0x80) { - // break code - if (matrix_is_on(ROW(code), COL(code))) { - matrix[ROW(code)] &= ~(1<<COL(code)); - is_modified = true; - } - } else { - // make code - if (!matrix_is_on(ROW(code), COL(code))) { - matrix[ROW(code)] |= (1<<COL(code)); - is_modified = true; - } - } - return code; -} - -bool matrix_is_modified(void) -{ - return is_modified; -} - -inline -bool matrix_has_ghost(void) -{ - return false; -} - -inline -bool matrix_is_on(uint8_t row, uint8_t col) -{ - return (matrix[row] & (1<<col)); -} - -inline -uint8_t matrix_get_row(uint8_t row) -{ - return matrix[row]; -} - -void matrix_print(void) -{ - print("\nr/c 01234567\n"); - for (uint8_t row = 0; row < matrix_rows(); row++) { - phex(row); print(": "); - pbin_reverse(matrix_get_row(row)); - print("\n"); - } -} - -uint8_t matrix_key_count(void) -{ - uint8_t count = 0; - for (uint8_t i = 0; i < MATRIX_ROWS; i++) { - count += bitpop(matrix[i]); - } - return count; -} diff --git a/x68k_usb/x68k.c b/x68k_usb/x68k.c deleted file mode 100644 index d17af51cc2..0000000000 --- a/x68k_usb/x68k.c +++ /dev/null @@ -1,75 +0,0 @@ -/* -Copyright 2012 Jun WAKO <wakojun@gmail.com> - -This software is licensed with a Modified BSD License. -All of this is supposed to be Free Software, Open Source, DFSG-free, -GPL-compatible, and OK to use in both free and proprietary applications. -Additions and corrections to this file are welcome. - - -Redistribution and use in source and binary forms, with or without -modification, are permitted provided that the following conditions are met: - -* Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - -* Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in - the documentation and/or other materials provided with the - distribution. - -* Neither the name of the copyright holders nor the names of - contributors may be used to endorse or promote products derived - from this software without specific prior written permission. - -THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE -ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE -LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR -CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF -SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS -INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) -ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -POSSIBILITY OF SUCH DAMAGE. -*/ - -#include <stdbool.h> -#include <avr/io.h> -#include <avr/interrupt.h> -#include "x68k.h" - - -void x68k_init(void) -{ - KBD_RX_INIT(); -} - -// RX ring buffer -#define RBUF_SIZE 8 -static uint8_t rbuf[RBUF_SIZE]; -static uint8_t rbuf_head = 0; -static uint8_t rbuf_tail = 0; - -uint8_t x68k_recv(void) -{ - uint8_t data = 0; - if (rbuf_head == rbuf_tail) { - return 0; - } - - data = rbuf[rbuf_tail]; - rbuf_tail = (rbuf_tail + 1) % RBUF_SIZE; - return data; -} - -// USART RX complete interrupt -ISR(KBD_RX_VECT) -{ - uint8_t next = (rbuf_head + 1) % RBUF_SIZE; - if (next != rbuf_tail) { - rbuf[rbuf_head] = KBD_RX_DATA; - rbuf_head = next; - } -} diff --git a/x68k_usb/x68k.h b/x68k_usb/x68k.h deleted file mode 100644 index 2cfda63a7a..0000000000 --- a/x68k_usb/x68k.h +++ /dev/null @@ -1,47 +0,0 @@ -/* -Copyright 2012 Jun WAKO <wakojun@gmail.com> - -This software is licensed with a Modified BSD License. -All of this is supposed to be Free Software, Open Source, DFSG-free, -GPL-compatible, and OK to use in both free and proprietary applications. -Additions and corrections to this file are welcome. - - -Redistribution and use in source and binary forms, with or without -modification, are permitted provided that the following conditions are met: - -* Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - -* Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in - the documentation and/or other materials provided with the - distribution. - -* Neither the name of the copyright holders nor the names of - contributors may be used to endorse or promote products derived - from this software without specific prior written permission. - -THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE -ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE -LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR -CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF -SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS -INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) -ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -POSSIBILITY OF SUCH DAMAGE. -*/ - -#ifndef X68K_H -#define X68K_H - -/* host role */ -void x68k_init(void); -uint8_t x68k_recv(void); - -/* device role */ - -#endif |