summaryrefslogtreecommitdiff
path: root/protocol/vusb/usbdrv/usbdrvasm165.inc
diff options
context:
space:
mode:
Diffstat (limited to 'protocol/vusb/usbdrv/usbdrvasm165.inc')
-rw-r--r--protocol/vusb/usbdrv/usbdrvasm165.inc453
1 files changed, 0 insertions, 453 deletions
diff --git a/protocol/vusb/usbdrv/usbdrvasm165.inc b/protocol/vusb/usbdrv/usbdrvasm165.inc
deleted file mode 100644
index 79b3c61cf8..0000000000
--- a/protocol/vusb/usbdrv/usbdrvasm165.inc
+++ /dev/null
@@ -1,453 +0,0 @@
-/* Name: usbdrvasm165.inc
- * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
- * Author: Christian Starkjohann
- * Creation Date: 2007-04-22
- * Tabsize: 4
- * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * Revision: $Id: usbdrvasm165.inc 740 2009-04-13 18:23:31Z cs $
- */
-
-/* Do not link this file! Link usbdrvasm.S instead, which includes the
- * appropriate implementation!
- */
-
-/*
-General Description:
-This file is the 16.5 MHz version of the USB driver. It is intended for the
-ATTiny45 and similar controllers running on 16.5 MHz internal RC oscillator.
-This version contains a phase locked loop in the receiver routine to cope with
-slight clock rate deviations of up to +/- 1%.
-
-See usbdrv.h for a description of the entire driver.
-
-Since almost all of this code is timing critical, don't change unless you
-really know what you are doing! Many parts require not only a maximum number
-of CPU cycles, but even an exact number of cycles!
-*/
-
-;Software-receiver engine. Strict timing! Don't change unless you can preserve timing!
-;interrupt response time: 4 cycles + insn running = 7 max if interrupts always enabled
-;max allowable interrupt latency: 59 cycles -> max 52 cycles interrupt disable
-;max stack usage: [ret(2), r0, SREG, YL, YH, shift, x1, x2, x3, x4, cnt] = 12 bytes
-;nominal frequency: 16.5 MHz -> 11 cycles per bit
-; 16.3125 MHz < F_CPU < 16.6875 MHz (+/- 1.1%)
-; Numbers in brackets are clocks counted from center of last sync bit
-; when instruction starts
-
-
-USB_INTR_VECTOR:
-;order of registers pushed: YL, SREG [sofError], r0, YH, shift, x1, x2, x3, x4, cnt
- push YL ;[-23] push only what is necessary to sync with edge ASAP
- in YL, SREG ;[-21]
- push YL ;[-20]
-;----------------------------------------------------------------------------
-; Synchronize with sync pattern:
-;----------------------------------------------------------------------------
-;sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
-;sync up with J to K edge during sync pattern -- use fastest possible loops
-;The first part waits at most 1 bit long since we must be in sync pattern.
-;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
-;waitForJ, ensure that this prerequisite is met.
-waitForJ:
- inc YL
- sbis USBIN, USBMINUS
- brne waitForJ ; just make sure we have ANY timeout
-waitForK:
-;The following code results in a sampling window of < 1/4 bit which meets the spec.
- sbis USBIN, USBMINUS ;[-15]
- rjmp foundK ;[-14]
- sbis USBIN, USBMINUS
- rjmp foundK
- sbis USBIN, USBMINUS
- rjmp foundK
- sbis USBIN, USBMINUS
- rjmp foundK
- sbis USBIN, USBMINUS
- rjmp foundK
- sbis USBIN, USBMINUS
- rjmp foundK
-#if USB_COUNT_SOF
- lds YL, usbSofCount
- inc YL
- sts usbSofCount, YL
-#endif /* USB_COUNT_SOF */
-#ifdef USB_SOF_HOOK
- USB_SOF_HOOK
-#endif
- rjmp sofError
-foundK: ;[-12]
-;{3, 5} after falling D- edge, average delay: 4 cycles [we want 5 for center sampling]
-;we have 1 bit time for setup purposes, then sample again. Numbers in brackets
-;are cycles from center of first sync (double K) bit after the instruction
- push r0 ;[-12]
-; [---] ;[-11]
- push YH ;[-10]
-; [---] ;[-9]
- lds YL, usbInputBufOffset;[-8]
-; [---] ;[-7]
- clr YH ;[-6]
- subi YL, lo8(-(usbRxBuf));[-5] [rx loop init]
- sbci YH, hi8(-(usbRxBuf));[-4] [rx loop init]
- mov r0, x2 ;[-3] [rx loop init]
- sbis USBIN, USBMINUS ;[-2] we want two bits K (sample 2 cycles too early)
- rjmp haveTwoBitsK ;[-1]
- pop YH ;[0] undo the pushes from before
- pop r0 ;[2]
- rjmp waitForK ;[4] this was not the end of sync, retry
-; The entire loop from waitForK until rjmp waitForK above must not exceed two
-; bit times (= 22 cycles).
-
-;----------------------------------------------------------------------------
-; push more registers and initialize values while we sample the first bits:
-;----------------------------------------------------------------------------
-haveTwoBitsK: ;[1]
- push shift ;[1]
- push x1 ;[3]
- push x2 ;[5]
- push x3 ;[7]
- ldi shift, 0xff ;[9] [rx loop init]
- ori x3, 0xff ;[10] [rx loop init] == ser x3, clear zero flag
-
- in x1, USBIN ;[11] <-- sample bit 0
- bst x1, USBMINUS ;[12]
- bld shift, 0 ;[13]
- push x4 ;[14] == phase
-; [---] ;[15]
- push cnt ;[16]
-; [---] ;[17]
- ldi phase, 0 ;[18] [rx loop init]
- ldi cnt, USB_BUFSIZE;[19] [rx loop init]
- rjmp rxbit1 ;[20]
-; [---] ;[21]
-
-;----------------------------------------------------------------------------
-; Receiver loop (numbers in brackets are cycles within byte after instr)
-;----------------------------------------------------------------------------
-/*
-byte oriented operations done during loop:
-bit 0: store data
-bit 1: SE0 check
-bit 2: overflow check
-bit 3: catch up
-bit 4: rjmp to achieve conditional jump range
-bit 5: PLL
-bit 6: catch up
-bit 7: jump, fixup bitstuff
-; 87 [+ 2] cycles
-------------------------------------------------------------------
-*/
-continueWithBit5:
- in x2, USBIN ;[055] <-- bit 5
- eor r0, x2 ;[056]
- or phase, r0 ;[057]
- sbrc phase, USBMINUS ;[058]
- lpm ;[059] optional nop3; modifies r0
- in phase, USBIN ;[060] <-- phase
- eor x1, x2 ;[061]
- bst x1, USBMINUS ;[062]
- bld shift, 5 ;[063]
- andi shift, 0x3f ;[064]
- in x1, USBIN ;[065] <-- bit 6
- breq unstuff5 ;[066] *** unstuff escape
- eor phase, x1 ;[067]
- eor x2, x1 ;[068]
- bst x2, USBMINUS ;[069]
- bld shift, 6 ;[070]
-didUnstuff6: ;[ ]
- in r0, USBIN ;[071] <-- phase
- cpi shift, 0x02 ;[072]
- brlo unstuff6 ;[073] *** unstuff escape
-didUnstuff5: ;[ ]
- nop2 ;[074]
-; [---] ;[075]
- in x2, USBIN ;[076] <-- bit 7
- eor x1, x2 ;[077]
- bst x1, USBMINUS ;[078]
- bld shift, 7 ;[079]
-didUnstuff7: ;[ ]
- eor r0, x2 ;[080]
- or phase, r0 ;[081]
- in r0, USBIN ;[082] <-- phase
- cpi shift, 0x04 ;[083]
- brsh rxLoop ;[084]
-; [---] ;[085]
-unstuff7: ;[ ]
- andi x3, ~0x80 ;[085]
- ori shift, 0x80 ;[086]
- in x2, USBIN ;[087] <-- sample stuffed bit 7
- nop ;[088]
- rjmp didUnstuff7 ;[089]
-; [---] ;[090]
- ;[080]
-
-unstuff5: ;[067]
- eor phase, x1 ;[068]
- andi x3, ~0x20 ;[069]
- ori shift, 0x20 ;[070]
- in r0, USBIN ;[071] <-- phase
- mov x2, x1 ;[072]
- nop ;[073]
- nop2 ;[074]
-; [---] ;[075]
- in x1, USBIN ;[076] <-- bit 6
- eor r0, x1 ;[077]
- or phase, r0 ;[078]
- eor x2, x1 ;[079]
- bst x2, USBMINUS ;[080]
- bld shift, 6 ;[081] no need to check bitstuffing, we just had one
- in r0, USBIN ;[082] <-- phase
- rjmp didUnstuff5 ;[083]
-; [---] ;[084]
- ;[074]
-
-unstuff6: ;[074]
- andi x3, ~0x40 ;[075]
- in x1, USBIN ;[076] <-- bit 6 again
- ori shift, 0x40 ;[077]
- nop2 ;[078]
-; [---] ;[079]
- rjmp didUnstuff6 ;[080]
-; [---] ;[081]
- ;[071]
-
-unstuff0: ;[013]
- eor r0, x2 ;[014]
- or phase, r0 ;[015]
- andi x2, USBMASK ;[016] check for SE0
- in r0, USBIN ;[017] <-- phase
- breq didUnstuff0 ;[018] direct jump to se0 would be too long
- andi x3, ~0x01 ;[019]
- ori shift, 0x01 ;[020]
- mov x1, x2 ;[021] mov existing sample
- in x2, USBIN ;[022] <-- bit 1 again
- rjmp didUnstuff0 ;[023]
-; [---] ;[024]
- ;[014]
-
-unstuff1: ;[024]
- eor r0, x1 ;[025]
- or phase, r0 ;[026]
- andi x3, ~0x02 ;[027]
- in r0, USBIN ;[028] <-- phase
- ori shift, 0x02 ;[029]
- mov x2, x1 ;[030]
- rjmp didUnstuff1 ;[031]
-; [---] ;[032]
- ;[022]
-
-unstuff2: ;[035]
- eor r0, x2 ;[036]
- or phase, r0 ;[037]
- andi x3, ~0x04 ;[038]
- in r0, USBIN ;[039] <-- phase
- ori shift, 0x04 ;[040]
- mov x1, x2 ;[041]
- rjmp didUnstuff2 ;[042]
-; [---] ;[043]
- ;[033]
-
-unstuff3: ;[043]
- in x2, USBIN ;[044] <-- bit 3 again
- eor r0, x2 ;[045]
- or phase, r0 ;[046]
- andi x3, ~0x08 ;[047]
- ori shift, 0x08 ;[048]
- nop ;[049]
- in r0, USBIN ;[050] <-- phase
- rjmp didUnstuff3 ;[051]
-; [---] ;[052]
- ;[042]
-
-unstuff4: ;[053]
- andi x3, ~0x10 ;[054]
- in x1, USBIN ;[055] <-- bit 4 again
- ori shift, 0x10 ;[056]
- rjmp didUnstuff4 ;[057]
-; [---] ;[058]
- ;[048]
-
-rxLoop: ;[085]
- eor x3, shift ;[086] reconstruct: x3 is 0 at bit locations we changed, 1 at others
- in x1, USBIN ;[000] <-- bit 0
- st y+, x3 ;[001]
-; [---] ;[002]
- eor r0, x1 ;[003]
- or phase, r0 ;[004]
- eor x2, x1 ;[005]
- in r0, USBIN ;[006] <-- phase
- ser x3 ;[007]
- bst x2, USBMINUS ;[008]
- bld shift, 0 ;[009]
- andi shift, 0xf9 ;[010]
-rxbit1: ;[ ]
- in x2, USBIN ;[011] <-- bit 1
- breq unstuff0 ;[012] *** unstuff escape
- andi x2, USBMASK ;[013] SE0 check for bit 1
-didUnstuff0: ;[ ] Z only set if we detected SE0 in bitstuff
- breq se0 ;[014]
- eor r0, x2 ;[015]
- or phase, r0 ;[016]
- in r0, USBIN ;[017] <-- phase
- eor x1, x2 ;[018]
- bst x1, USBMINUS ;[019]
- bld shift, 1 ;[020]
- andi shift, 0xf3 ;[021]
-didUnstuff1: ;[ ]
- in x1, USBIN ;[022] <-- bit 2
- breq unstuff1 ;[023] *** unstuff escape
- eor r0, x1 ;[024]
- or phase, r0 ;[025]
- subi cnt, 1 ;[026] overflow check
- brcs overflow ;[027]
- in r0, USBIN ;[028] <-- phase
- eor x2, x1 ;[029]
- bst x2, USBMINUS ;[030]
- bld shift, 2 ;[031]
- andi shift, 0xe7 ;[032]
-didUnstuff2: ;[ ]
- in x2, USBIN ;[033] <-- bit 3
- breq unstuff2 ;[034] *** unstuff escape
- eor r0, x2 ;[035]
- or phase, r0 ;[036]
- eor x1, x2 ;[037]
- bst x1, USBMINUS ;[038]
- in r0, USBIN ;[039] <-- phase
- bld shift, 3 ;[040]
- andi shift, 0xcf ;[041]
-didUnstuff3: ;[ ]
- breq unstuff3 ;[042] *** unstuff escape
- nop ;[043]
- in x1, USBIN ;[044] <-- bit 4
- eor x2, x1 ;[045]
- bst x2, USBMINUS ;[046]
- bld shift, 4 ;[047]
-didUnstuff4: ;[ ]
- eor r0, x1 ;[048]
- or phase, r0 ;[049]
- in r0, USBIN ;[050] <-- phase
- andi shift, 0x9f ;[051]
- breq unstuff4 ;[052] *** unstuff escape
- rjmp continueWithBit5;[053]
-; [---] ;[054]
-
-macro POP_STANDARD ; 16 cycles
- pop cnt
- pop x4
- pop x3
- pop x2
- pop x1
- pop shift
- pop YH
- pop r0
- endm
-macro POP_RETI ; 5 cycles
- pop YL
- out SREG, YL
- pop YL
- endm
-
-#include "asmcommon.inc"
-
-
-; USB spec says:
-; idle = J
-; J = (D+ = 0), (D- = 1)
-; K = (D+ = 1), (D- = 0)
-; Spec allows 7.5 bit times from EOP to SOP for replies
-
-bitstuff7:
- eor x1, x4 ;[4]
- ldi x2, 0 ;[5]
- nop2 ;[6] C is zero (brcc)
- rjmp didStuff7 ;[8]
-
-bitstuffN:
- eor x1, x4 ;[5]
- ldi x2, 0 ;[6]
- lpm ;[7] 3 cycle NOP, modifies r0
- out USBOUT, x1 ;[10] <-- out
- rjmp didStuffN ;[0]
-
-#define bitStatus x3
-
-sendNakAndReti:
- ldi cnt, USBPID_NAK ;[-19]
- rjmp sendCntAndReti ;[-18]
-sendAckAndReti:
- ldi cnt, USBPID_ACK ;[-17]
-sendCntAndReti:
- mov r0, cnt ;[-16]
- ldi YL, 0 ;[-15] R0 address is 0
- ldi YH, 0 ;[-14]
- ldi cnt, 2 ;[-13]
-; rjmp usbSendAndReti fallthrough
-
-;usbSend:
-;pointer to data in 'Y'
-;number of bytes in 'cnt' -- including sync byte [range 2 ... 12]
-;uses: x1...x4, shift, cnt, Y
-;Numbers in brackets are time since first bit of sync pattern is sent
-usbSendAndReti: ; 12 cycles until SOP
- in x2, USBDDR ;[-12]
- ori x2, USBMASK ;[-11]
- sbi USBOUT, USBMINUS;[-10] prepare idle state; D+ and D- must have been 0 (no pullups)
- in x1, USBOUT ;[-8] port mirror for tx loop
- out USBDDR, x2 ;[-7] <- acquire bus
-; need not init x2 (bitstuff history) because sync starts with 0
- ldi x4, USBMASK ;[-6] exor mask
- ldi shift, 0x80 ;[-5] sync byte is first byte sent
- ldi bitStatus, 0xff ;[-4] init bit loop counter, works for up to 12 bytes
-byteloop:
-bitloop:
- sbrs shift, 0 ;[8] [-3]
- eor x1, x4 ;[9] [-2]
- out USBOUT, x1 ;[10] [-1] <-- out
- ror shift ;[0]
- ror x2 ;[1]
-didStuffN:
- cpi x2, 0xfc ;[2]
- brcc bitstuffN ;[3]
- nop ;[4]
- subi bitStatus, 37 ;[5] 256 / 7 ~=~ 37
- brcc bitloop ;[6] when we leave the loop, bitStatus has almost the initial value
- sbrs shift, 0 ;[7]
- eor x1, x4 ;[8]
- ror shift ;[9]
-didStuff7:
- out USBOUT, x1 ;[10] <-- out
- ror x2 ;[0]
- cpi x2, 0xfc ;[1]
- brcc bitstuff7 ;[2]
- ld shift, y+ ;[3]
- dec cnt ;[5]
- brne byteloop ;[6]
-;make SE0:
- cbr x1, USBMASK ;[7] prepare SE0 [spec says EOP may be 21 to 25 cycles]
- lds x2, usbNewDeviceAddr;[8]
- lsl x2 ;[10] we compare with left shifted address
- out USBOUT, x1 ;[11] <-- out SE0 -- from now 2 bits = 22 cycles until bus idle
-;2006-03-06: moved transfer of new address to usbDeviceAddr from C-Code to asm:
-;set address only after data packet was sent, not after handshake
- subi YL, 2 ;[0] Only assign address on data packets, not ACK/NAK in r0
- sbci YH, 0 ;[1]
- breq skipAddrAssign ;[2]
- sts usbDeviceAddr, x2; if not skipped: SE0 is one cycle longer
-skipAddrAssign:
-;end of usbDeviceAddress transfer
- ldi x2, 1<<USB_INTR_PENDING_BIT;[4] int0 occurred during TX -- clear pending flag
- USB_STORE_PENDING(x2) ;[5]
- ori x1, USBIDLE ;[6]
- in x2, USBDDR ;[7]
- cbr x2, USBMASK ;[8] set both pins to input
- mov x3, x1 ;[9]
- cbr x3, USBMASK ;[10] configure no pullup on both pins
- ldi x4, 4 ;[11]
-se0Delay:
- dec x4 ;[12] [15] [18] [21]
- brne se0Delay ;[13] [16] [19] [22]
- out USBOUT, x1 ;[23] <-- out J (idle) -- end of SE0 (EOP signal)
- out USBDDR, x2 ;[24] <-- release bus now
- out USBOUT, x3 ;[25] <-- ensure no pull-up resistors are active
- rjmp doReturn
-