diff options
Diffstat (limited to 'keyboards/scythe')
| -rw-r--r-- | keyboards/scythe/config.h | 7 | ||||
| -rw-r--r-- | keyboards/scythe/rules.mk | 52 |
2 files changed, 2 insertions, 57 deletions
diff --git a/keyboards/scythe/config.h b/keyboards/scythe/config.h index 66d47c3566..d577192db3 100644 --- a/keyboards/scythe/config.h +++ b/keyboards/scythe/config.h @@ -114,13 +114,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. * */ -/* key combination for magic key command */ -/* -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ -) -*/ - /* control how magic key switches layers */ //#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true //#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true diff --git a/keyboards/scythe/rules.mk b/keyboards/scythe/rules.mk index 1ad80dc898..54f2f7a529 100644 --- a/keyboards/scythe/rules.mk +++ b/keyboards/scythe/rules.mk @@ -1,64 +1,16 @@ # MCU name -#MCU = at90usb1286 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # |