diff options
Diffstat (limited to 'keyboards/planck/keymaps/vaire')
| -rw-r--r-- | keyboards/planck/keymaps/vaire/config.h | 9 | ||||
| -rw-r--r-- | keyboards/planck/keymaps/vaire/rules.mk | 84 |
2 files changed, 4 insertions, 89 deletions
diff --git a/keyboards/planck/keymaps/vaire/config.h b/keyboards/planck/keymaps/vaire/config.h index 96a13cc427..a5e236e4a9 100644 --- a/keyboards/planck/keymaps/vaire/config.h +++ b/keyboards/planck/keymaps/vaire/config.h @@ -1,15 +1,9 @@ -#pragma - - - +#pragma once /* * MIDI options */ -/* Prevent use of disabled MIDI features in the keymap */ -//#define MIDI_ENABLE_STRICT 1 - /* enable basic MIDI features: - MIDI notes can be sent when in Music mode is on */ @@ -18,7 +12,6 @@ #define MOUSEKEY_TIME_TO_MAX 60 #define MOUSEKEY_MAX_SPEED 7 #define MOUSEKEY_WHEEL_DELAY 0 - #define MIDI_BASIC diff --git a/keyboards/planck/keymaps/vaire/rules.mk b/keyboards/planck/keymaps/vaire/rules.mk index f9dfeb7263..427c06822c 100644 --- a/keyboards/planck/keymaps/vaire/rules.mk +++ b/keyboards/planck/keymaps/vaire/rules.mk @@ -1,81 +1,3 @@ -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. -ifeq ($(strip $(KEYBOARD)), planck/rev3) - BOOTLOADER = atmel-dfu -endif -ifeq ($(strip $(KEYBOARD)), planck/rev4) - BOOTLOADER = atmel-dfu -endif -ifeq ($(strip $(KEYBOARD)), planck/rev5) - BOOTLOADER = qmk-dfu -endif -ifeq ($(strip $(KEYBOARD)), planck/light) - BOOTLOADER = qmk-dfu -endif - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in[] -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -MIDI_ENABLE = no # MIDI controls -AUDIO_ENABLE = yes # Audio output on port C6 -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. -API_SYSEX_ENABLE = no - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - -LAYOUTS = ortho_4x12 planck_mit planck_grid -LAYOUTS_HAS_RGB = no - -DEFAULT_FOLDER = planck/rev5 - +MOUSEKEY_ENABLE = yes +CONSOLE_ENABLE = no +BACKLIGHT_ENABLE = yes |