diff options
Diffstat (limited to 'keyboards/handwired')
309 files changed, 10629 insertions, 3080 deletions
diff --git a/keyboards/handwired/108key_trackpoint/rules.mk b/keyboards/handwired/108key_trackpoint/rules.mk index 84ec52eee9..2a8ed6af15 100644 --- a/keyboards/handwired/108key_trackpoint/rules.mk +++ b/keyboards/handwired/108key_trackpoint/rules.mk @@ -1,43 +1,5 @@ # MCU name MCU = at90usb1286 -#MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay @@ -45,19 +7,10 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - # Build Options # change yes to no to disable # diff --git a/keyboards/handwired/2x5keypad/2x5keypad.c b/keyboards/handwired/2x5keypad/2x5keypad.c new file mode 100644 index 0000000000..873c579a17 --- /dev/null +++ b/keyboards/handwired/2x5keypad/2x5keypad.c @@ -0,0 +1,25 @@ +#include "2x5keypad.h" + + +void matrix_init_kb(void) +{ + matrix_init_user(); + + setPinOutput(RED_LED); + setPinOutput(BLUE_LED); + setPinOutput(GREEN_LED); +} + + + +void turn_off_leds(void) +{ + writePinLow(RED_LED); + writePinLow(BLUE_LED); + writePinLow(GREEN_LED); +} + +void turn_on_led(pin_t pin) +{ + writePinHigh(pin); +} diff --git a/keyboards/handwired/2x5keypad/2x5keypad.h b/keyboards/handwired/2x5keypad/2x5keypad.h new file mode 100644 index 0000000000..6284e83b72 --- /dev/null +++ b/keyboards/handwired/2x5keypad/2x5keypad.h @@ -0,0 +1,21 @@ +#pragma once + +#include "quantum.h" + +#define RED_LED D0 +#define BLUE_LED B5 +#define GREEN_LED B6 + + +#define LAYOUT( \ + K00, K01, K02, K03, K04, \ + K10, K11, K12, K13, K14 \ +) { \ + { K00, K01, K02, K03, K04 }, \ + { K10, K11, K12, K13, K14 } \ +} + + + +void turn_off_leds(void); +void turn_on_led(pin_t pin); diff --git a/keyboards/handwired/2x5keypad/config.h b/keyboards/handwired/2x5keypad/config.h new file mode 100644 index 0000000000..35a0fda8d1 --- /dev/null +++ b/keyboards/handwired/2x5keypad/config.h @@ -0,0 +1,56 @@ +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x2020 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Jonathan Cameron +#define PRODUCT 2x5keypad +#define DESCRIPTION 2x5 Keypad + +/* key matrix size */ +#define MATRIX_ROWS 2 +#define MATRIX_COLS 5 + +/* key matrix pins */ +#define MATRIX_ROW_PINS { B3, B2 } +#define MATRIX_COL_PINS { D4, C6, D7, E6, B4 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* number of backlight levels */ + +#ifdef BACKLIGHT_PIN +#define BACKLIGHT_LEVELS 0 +#endif + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE + +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* Tap dancing params */ +#define TAPPING_TERM 250 + +/* key combination for command */ +/* DISABLED +#define IS_COMMAND() ( \ + get_mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) +*/ + +#ifdef RGB_DI_PIN +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 0 +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#endif diff --git a/keyboards/handwired/2x5keypad/keymaps/default/keymap.c b/keyboards/handwired/2x5keypad/keymaps/default/keymap.c new file mode 100644 index 0000000000..91a0e28f6a --- /dev/null +++ b/keyboards/handwired/2x5keypad/keymaps/default/keymap.c @@ -0,0 +1,164 @@ +#include QMK_KEYBOARD_H + +#define WIN_TAB LGUI(KC_TAB) +#define WIN_LOCK LGUI(KC_L) + +enum layers { + NORMAL_LAYER = 0, + MEDIA_LAYER, + TBD_LAYER2, + FRENCH_LAYER +}; + + +/* Enum for the tap dancing keys */ +enum tap_codes { + A_Q, E_Q, E_U, E_E, + A_Y, I_I, O_C, U_U +}; + +#define FR_A_GRAVE "00E0" +#define FR_A_HAT "00E2" + +#define FR_C_CIRCUM "00E7" + +#define FR_E_AIGU "00E9" +#define FR_E_GRAVE "00E8" +#define FR_E_HAT "00EA" +#define FR_E_UMLAUT "00EB" + +#define FR_I_HAT "00EE" +#define FR_I_UMLAUT "00EF" + +#define FR_O_HAT "00F4" + +#define FR_U_GRAVE "00F9" +#define FR_U_HAT "00FB" +#define FR_U_UMLAUT "00FC" + +#define FR_Y_UMLAUT "00FF" + +#define FR_L_QUOTE "00AB" +#define FR_R_QUOTE "00BB" + +void send_french_unicode_char(uint8_t count, char *once, char *twice) +{ + if (count <= 1) + send_unicode_hex_string(once); + else + send_unicode_hex_string(twice); +} + +void dance_a_q(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_A_GRAVE, FR_L_QUOTE); +} + +void dance_e_q(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_E_AIGU, FR_R_QUOTE); +} + +void dance_e_u(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_E_GRAVE, FR_U_GRAVE); +} + +void dance_e_e(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_E_HAT, FR_E_UMLAUT); +} + +void dance_a_y(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_A_HAT, FR_Y_UMLAUT); +} + +void dance_i_i(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_I_HAT, FR_I_UMLAUT); +} + +void dance_o_c(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_O_HAT, FR_C_CIRCUM); +} + +void dance_u_u(qk_tap_dance_state_t *state, void *user_data) +{ + send_french_unicode_char(state->count, FR_U_HAT, FR_U_UMLAUT); +} + +/* Define the tap dance actions for the french characters */ +qk_tap_dance_action_t tap_dance_actions[] = { + [A_Q] = ACTION_TAP_DANCE_FN(dance_a_q), + [E_Q] = ACTION_TAP_DANCE_FN(dance_e_q), + [E_U] = ACTION_TAP_DANCE_FN(dance_e_u), + [E_E] = ACTION_TAP_DANCE_FN(dance_e_e), + + [A_Y] = ACTION_TAP_DANCE_FN(dance_a_y), + [I_I] = ACTION_TAP_DANCE_FN(dance_i_i), + [O_C] = ACTION_TAP_DANCE_FN(dance_o_c), + [U_U] = ACTION_TAP_DANCE_FN(dance_u_u) +}; + + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + [NORMAL_LAYER] = LAYOUT(TO(1), WIN_TAB, KC_HOME, KC_UP, KC_END, + WIN_LOCK, KC_MUTE, KC_LEFT, KC_DOWN, KC_RGHT), + + [MEDIA_LAYER] = LAYOUT(TO(2), KC_CALC, KC_MPRV, KC_MNXT, KC_VOLU, + KC_TRNS, KC_TRNS, KC_MSTP, KC_MPLY, KC_VOLD), + + [TBD_LAYER2] = LAYOUT(TO(3), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + + [FRENCH_LAYER] = LAYOUT(TO(0), TD(A_Q), TD(E_Q), TD(E_U), TD(E_E), + KC_TRNS, TD(A_Y), TD(I_I), TD(O_C), TD(U_U)) +}; + + +/* DISABLED +void matrix_init_user(void) { +} + +void matrix_scan_user(void) { +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} +*/ + + +void matrix_init_user(void) +{ + set_unicode_input_mode(UC_WINC); /* See https://jayliu50.github.io/qmk-cheatsheet/ */ +} + + +layer_state_t layer_state_set_user(layer_state_t state) +{ + turn_off_leds(); + + switch (biton32(state)) + { + case NORMAL_LAYER: + break; + + case MEDIA_LAYER: + turn_on_led(RED_LED); + break; + + case TBD_LAYER2: + turn_on_led(BLUE_LED); + break; + + case FRENCH_LAYER: + turn_on_led(GREEN_LED); + break; + } + return state; +} diff --git a/keyboards/handwired/2x5keypad/readme.md b/keyboards/handwired/2x5keypad/readme.md new file mode 100644 index 0000000000..d87a2e0178 --- /dev/null +++ b/keyboards/handwired/2x5keypad/readme.md @@ -0,0 +1,26 @@ +# 2x5keypad + + + +This Keypad has 2 rows x 5 columns of keys. It has the top/default layer that +has a few handy navigation keys as well as one dedicated key to cycle through +the layers. The second layer has some media keys. The third and fourth layers +are currently undefined (although I may use them for inserting accented French +characters). The keypad also includes three LEDs that show which layer is +active (no lit LEDs means the default layer). + +Keyboard Maintainer: [Jonathan Cameron](https://github.com/jmcameron) + +Hardware: + * Key switch holes cut in blank piece of copper-clad project board + * Uses Kailh Box White switches with relegendable keycaps + * Chassis is three layers of wood + * Handwired + * Uses a Pro Micro + * Includes a reset switch accessible by a hole on the bottom + +Make example for this keyboard (after setting up your build environment): + + make handwired/2x5keyapd:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/2x5keypad/rules.mk b/keyboards/handwired/2x5keypad/rules.mk new file mode 100644 index 0000000000..e62a0f24a8 --- /dev/null +++ b/keyboards/handwired/2x5keypad/rules.mk @@ -0,0 +1,27 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina + + +AUDIO_ENABLE = no +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration +COMMAND_ENABLE = no # Commands for debug and configuration +CONSOLE_ENABLE= no # Console for debug +EXTRAKEY_ENABLE = yes # Audio control and System control +MOUSEKEY_ENABLE = yes # Mouse keys +NKRO_ENABLE = yes # USB Nkey Rollover - + +RGBLIGHT_ENABLE = no +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +UNICODE_ENABLE = yes +TAP_DANCE_ENABLE = yes diff --git a/keyboards/handwired/412_64/keymaps/default/keymap.c b/keyboards/handwired/412_64/keymaps/default/keymap.c index 405c563056..27966eb9a5 100644 --- a/keyboards/handwired/412_64/keymaps/default/keymap.c +++ b/keyboards/handwired/412_64/keymaps/default/keymap.c @@ -71,17 +71,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { }; -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) { - keyevent_t event = record->event; - (void)event; - - switch (id) { - - } - return MACRO_NONE; -} - - void matrix_init_user(void) { } diff --git a/keyboards/handwired/412_64/rules.mk b/keyboards/handwired/412_64/rules.mk index 9e74da5d98..c7dfa8705b 100644 --- a/keyboards/handwired/412_64/rules.mk +++ b/keyboards/handwired/412_64/rules.mk @@ -1,53 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options diff --git a/keyboards/handwired/42/42.h b/keyboards/handwired/42/42.h new file mode 100644 index 0000000000..5be29bf252 --- /dev/null +++ b/keyboards/handwired/42/42.h @@ -0,0 +1,32 @@ +/* Copyright 2019 Angelo Gazzola (nglgzz) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +#define ___ KC_NO +#define LAYOUT( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ + K33, K34, K35, K36, K37, K38 \ +) { \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ + { ___, ___, ___, K33, K34, K35, K36, K37, K38, ___, ___, ___ } \ +} diff --git a/keyboards/handwired/42/README.md b/keyboards/handwired/42/README.md new file mode 100644 index 0000000000..20fb67aa7e --- /dev/null +++ b/keyboards/handwired/42/README.md @@ -0,0 +1,15 @@ +# 42 + +42-keys ergonomic keyboard running on Adafruit Feather BLE. + + + +Keyboard Maintainer: [Angelo Gazzola (nglgzz)](https://github.com/nglgzz) +Hardware Supported: 42 (rev2, rev3), Feather 32u4 BLE +Hardware Availability: [GitHub](https://github.com/nglgzz/42/) + +Make example for this keyboard (after setting up your build environment): + + make handwired/42:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/42/config.h b/keyboards/handwired/42/config.h new file mode 100644 index 0000000000..3f5060989b --- /dev/null +++ b/keyboards/handwired/42/config.h @@ -0,0 +1,42 @@ +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0003 +#define MANUFACTURER nglgzz +#define PRODUCT 42 +#define DESCRIPTION BT + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_COL_PINS { F5, F6, F7, F0, F1, F4, B6, B5, D7, C7, D6, B7 } +#define MATRIX_ROW_PINS { D2, D3, D0, D1 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +#define TAPPING_TERM 100 diff --git a/keyboards/handwired/42/keymaps/default/keymap.c b/keyboards/handwired/42/keymaps/default/keymap.c new file mode 100644 index 0000000000..099e1fa012 --- /dev/null +++ b/keyboards/handwired/42/keymaps/default/keymap.c @@ -0,0 +1,47 @@ +#include QMK_KEYBOARD_H + +// MOD_KC +#define CTL_ESC MT(MOD_LCTL, KC_ESCAPE) +#define CTL_ENT MT(MOD_LCTL, KC_ENTER) +#define ALT_Z MT(MOD_LALT, KC_Z) +#define ALT_SLS MT(MOD_LALT, KC_SLASH) +#define SU_QUOT MT(MOD_LGUI, KC_QUOTE) +#define SU_BSLS MT(MOD_LGUI, KC_BSLS) +#define SFT_DEL MT(MOD_LSFT, KC_DELETE) + +// LAYER_KC +#define L3_SPC LT(3, KC_SPC) +#define L2_SPC LT(2, KC_SPC) +#define L1_LBRC LT(1, KC_LBRC) +#define L1_RBRC LT(1, KC_RBRC) + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + // Default Layer + LAYOUT( + KC_TAB , KC_Q , KC_W , KC_E , KC_R , KC_T , KC_Y , KC_U , KC_I , KC_O , KC_P , KC_BSPC, + CTL_ESC, KC_A , KC_S , KC_D , KC_F , KC_G , KC_H , KC_J , KC_K , KC_L , KC_SCLN, CTL_ENT, + KC_LSFT, ALT_Z , KC_X , KC_C , KC_V , KC_B , KC_N , KC_M , KC_COMM, KC_DOT , ALT_SLS, SFT_DEL, + L1_LBRC, L3_SPC , SU_QUOT, SU_BSLS, L2_SPC , L1_RBRC + ), + // Symbols Layer + LAYOUT( + KC_GRV , KC_1 , KC_2 , KC_3 , KC_4 , KC_5 , KC_6 , KC_7 , KC_8 , KC_9 , KC_0 , KC_EQL , + KC_INS , S(KC_1), S(KC_2), S(KC_3), S(KC_4), S(KC_5), S(KC_6), S(KC_7), S(KC_8), S(KC_9), S(KC_0), KC_MINS, + KC_F1 , KC_F2 , KC_F3 , KC_F4 , KC_F5 , KC_F6 , KC_F7 , KC_F8 , KC_F9 , KC_F10 , KC_F11 , KC_F12 , + KC_CAPS, OUT_USB, OUT_BT , _______, _______, _______ + ), + // Navigation Layer + LAYOUT( + _______, _______, _______, KC_PGUP, _______, _______, KC_BRIU, _______, KC_UP , _______, _______, _______, + _______, _______, KC_HOME, KC_PGDN, KC_END , _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, + _______, _______, _______, _______, _______, _______, KC_BRID, KC_VOLD, KC_MUTE, KC_VOLU, _______, _______, + _______, _______, _______, _______, _______, _______ + ), + // Mouse Layer + LAYOUT( + _______, _______, KC_WREF, KC_WH_U, KC_WSCH, _______, _______, KC_BTN1, KC_MS_U, KC_BTN2, _______, _______, + _______, _______, KC_WH_L, KC_WH_D, KC_WH_R, _______, _______, KC_MS_L, KC_MS_D, KC_MS_R, _______, _______, + _______, _______, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______ + ) +}; diff --git a/keyboards/handwired/42/rules.mk b/keyboards/handwired/42/rules.mk new file mode 100644 index 0000000000..f2306f310f --- /dev/null +++ b/keyboards/handwired/42/rules.mk @@ -0,0 +1,39 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency +F_CPU = 8000000 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328p USBasp +BOOTLOADER = caterina + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = no # Console for debug +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs + +UNICODE_ENABLE = no # Unicode +UNICODEMAP_ENABLE = no # ^^ +UCIS_ENABLE = no # ^^ +BLUETOOTH = AdafruitBLE diff --git a/keyboards/handwired/6macro/6macro.c b/keyboards/handwired/6macro/6macro.c new file mode 100644 index 0000000000..0a62bedf16 --- /dev/null +++ b/keyboards/handwired/6macro/6macro.c @@ -0,0 +1,16 @@ +/* Copyright 2019 joaofbmaia + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "6macro.h" diff --git a/keyboards/handwired/6macro/6macro.h b/keyboards/handwired/6macro/6macro.h new file mode 100644 index 0000000000..c1d5005128 --- /dev/null +++ b/keyboards/handwired/6macro/6macro.h @@ -0,0 +1,35 @@ +/* Copyright 2019 joaofbmaia + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT( \ + k00, k01, k02, \ + k10, k11, k12 \ +) \ +{ \ + { k00, k01, k02 }, \ + { k10, k11, k12 }, \ +} diff --git a/keyboards/handwired/6macro/config.h b/keyboards/handwired/6macro/config.h new file mode 100644 index 0000000000..7919c3c71f --- /dev/null +++ b/keyboards/handwired/6macro/config.h @@ -0,0 +1,70 @@ +/* +Copyright 2019 joaofbmaia + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0037 +#define DEVICE_VER 0x0001 +#define MANUFACTURER joaofbmaia +#define PRODUCT 6macro +#define DESCRIPTION 6macro + +/* key matrix size */ +#define MATRIX_ROWS 2 +#define MATRIX_COLS 3 + +/* pinout - DON'T CHANGE */ +#define MATRIX_ROW_PINS { B3, B4 } +#define MATRIX_COL_PINS { B0, B1, B2 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +#define RGB_DI_PIN D2 +#define RGBLED_NUM 10 +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 +#define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ +// #define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ +// /*== all animations enable ==*/ +// #define RGBLIGHT_ANIMATIONS +// /*== or choose animations ==*/ +#define RGBLIGHT_EFFECT_BREATHING +#define RGBLIGHT_EFFECT_RAINBOW_MOOD +#define RGBLIGHT_EFFECT_RAINBOW_SWIRL +#define RGBLIGHT_EFFECT_SNAKE +#define RGBLIGHT_EFFECT_KNIGHT +// #define RGBLIGHT_EFFECT_CHRISTMAS +#define RGBLIGHT_EFFECT_STATIC_GRADIENT +// #define RGBLIGHT_EFFECT_RGB_TEST +// #define RGBLIGHT_EFFECT_ALTERNATING +// /*== customize breathing effect ==*/ +// /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ +// #define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 +// /*==== use exp() and sin() ====*/ +// #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 +// #define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5
\ No newline at end of file diff --git a/keyboards/handwired/6macro/info.json b/keyboards/handwired/6macro/info.json new file mode 100644 index 0000000000..52bd03a1dd --- /dev/null +++ b/keyboards/handwired/6macro/info.json @@ -0,0 +1,13 @@ +{ + "keyboard_name": "6macro", + "url": "", + "maintainer": "joaofbmaia", + "width": 3, + "height": 2, + "layouts": { + "LAYOUT": { + "layout": [{"label":"k00", "x":0, "y":0}, {"label":"k01", "x":1, "y":0}, {"label":"k02", "x":2, "y":0}, {"label":"k10", "x":0, "y":1}, {"label":"k11", "x":1, "y":1}, {"label":"k12", "x":2, "y":1}] + } + } + } +
\ No newline at end of file diff --git a/keyboards/handwired/6macro/keymaps/default/config.h b/keyboards/handwired/6macro/keymaps/default/config.h new file mode 100644 index 0000000000..64ba57443f --- /dev/null +++ b/keyboards/handwired/6macro/keymaps/default/config.h @@ -0,0 +1,18 @@ +/* Copyright 2019 joaofbmaia + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + diff --git a/keyboards/handwired/6macro/keymaps/default/keymap.c b/keyboards/handwired/6macro/keymaps/default/keymap.c new file mode 100644 index 0000000000..365dbf7b05 --- /dev/null +++ b/keyboards/handwired/6macro/keymaps/default/keymap.c @@ -0,0 +1,56 @@ +/* Copyright 2019 joaofbmaia + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + /* LAYER 0 + * ,-----------------------. + * | F13 | F14 | F15/FN| Hold for FN + * |-------+-------+-------| + * | F16 | F17 | F18 | + * `-------+-------+-------' + */ + [0] = LAYOUT( + KC_F13, KC_F14, LT(1, KC_F15), \ + KC_F16, KC_F17, KC_F18 \ + ), + + /* LAYER 1 + * ,-----------------------. + * |RGB_TOG|RGBMOD+| | + * |-------+-------+-------| + * |RGBHUE+|RGBBRI+|Spec FN| Hold along with previous to access special funtions (RESET) + * `-------+-------+-------' + */ + [1] = LAYOUT( + RGB_TOG, RGB_MOD, KC_TRNS, \ + RGB_HUI, RGB_VAI, MO(2) \ + ), + + /* LAYER 2 + * ,-----------------------. + * | RESET |RGBMOD-| | + * |-------+-------+-------| + * |RGBHUE-|RGBBRI-| | + * `-------+-------+-------' + */ + [2] = LAYOUT( + RESET, RGB_RMOD, KC_NO, \ + RGB_HUD, RGB_VAD, KC_TRNS \ + ) + +}; diff --git a/keyboards/handwired/6macro/keymaps/default/readme.md b/keyboards/handwired/6macro/keymaps/default/readme.md new file mode 100644 index 0000000000..dd42a8fc62 --- /dev/null +++ b/keyboards/handwired/6macro/keymaps/default/readme.md @@ -0,0 +1,15 @@ +Layer 0: + + + +Layer 1: + + + +Layer 2: + + + +# Default 6macro Layout + +This is the default layout. Layer 0 is mappped to function keys 13-18. Top right key switches to layer above when held. Upper layers are for RGB control.
\ No newline at end of file diff --git a/keyboards/handwired/6macro/keymaps/osu/config.h b/keyboards/handwired/6macro/keymaps/osu/config.h new file mode 100644 index 0000000000..64ba57443f --- /dev/null +++ b/keyboards/handwired/6macro/keymaps/osu/config.h @@ -0,0 +1,18 @@ +/* Copyright 2019 joaofbmaia + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + diff --git a/keyboards/handwired/6macro/keymaps/osu/keymap.c b/keyboards/handwired/6macro/keymaps/osu/keymap.c new file mode 100644 index 0000000000..ffed7d909f --- /dev/null +++ b/keyboards/handwired/6macro/keymaps/osu/keymap.c @@ -0,0 +1,56 @@ +/* Copyright 2019 joaofbmaia + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + /* LAYER 0 + * ,-----------------------. + * | ESC | ~ | SPC/FN| Hold for FN + * |-------+-------+-------| + * | C | Z | X | + * `-------+-------+-------' + */ + [0] = LAYOUT( + KC_ESC, KC_GRAVE, LT(1, KC_SPC), \ + KC_C, KC_Z, KC_X \ + ), + + /* LAYER 1 + * ,-----------------------. + * |RGB_TOG|RGBMOD+| | + * |-------+-------+-------| + * |RGBHUE+|RGBBRI+|Spec FN| Hold along with previous to access special funtions (RESET) + * `-------+-------+-------' + */ + [1] = LAYOUT( + RGB_TOG, RGB_MOD, KC_TRNS, \ + RGB_HUI, RGB_VAI, MO(2) \ + ), + + /* LAYER 2 + * ,-----------------------. + * | RESET |RGBMOD-| | + * |-------+-------+-------| + * |RGBHUE-|RGBBRI-| | + * `-------+-------+-------' + */ + [2] = LAYOUT( + RESET, RGB_RMOD, KC_NO, \ + RGB_HUD, RGB_VAD, KC_TRNS \ + ) + +}; diff --git a/keyboards/handwired/6macro/keymaps/osu/readme.md b/keyboards/handwired/6macro/keymaps/osu/readme.md new file mode 100644 index 0000000000..0de5d6bf2e --- /dev/null +++ b/keyboards/handwired/6macro/keymaps/osu/readme.md @@ -0,0 +1,15 @@ +Layer 0: + + + +Layer 1: + + + +Layer 2: + + + +# OSU 6macro Layout + +This layout is for the game OSU. Layer 0 is mappped as shown above. Top right key switches to layer above when held. Upper layers are for RGB control.
\ No newline at end of file diff --git a/keyboards/handwired/6macro/readme.md b/keyboards/handwired/6macro/readme.md new file mode 100644 index 0000000000..3fbd917c80 --- /dev/null +++ b/keyboards/handwired/6macro/readme.md @@ -0,0 +1,15 @@ +# 6macro + + + + +This is a 6-key keyboard intended for macros or as a dedicated controller for games with few bindings. + +Keyboard Maintainer: [joaofbmaia](https://github.com/joaofbmaia) +Hardware: https://github.com/joaofbmaia/6macro + +Make example for this keyboard (after setting up your build environment): + + make handwired/6macro:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/6macro/rules.mk b/keyboards/handwired/6macro/rules.mk new file mode 100644 index 0000000000..13760ae066 --- /dev/null +++ b/keyboards/handwired/6macro/rules.mk @@ -0,0 +1,34 @@ +# MCU name +MCU = atmega32u2 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +#RGB_MATRIX_ENABLE = WS2812 # Enable per-key coordinate based RGB effects. Do not enable with RGBlight (+8500) +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = yes # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) diff --git a/keyboards/handwired/aek64/aek64.c b/keyboards/handwired/aek64/aek64.c new file mode 100644 index 0000000000..0646d308d0 --- /dev/null +++ b/keyboards/handwired/aek64/aek64.c @@ -0,0 +1,36 @@ +/* +Copyright 2012,2013 Jun Wako <wakojun@gmail.com> <4sStylZ@protonmail.ch> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include "quantum.h" + +/* + * Hardware function pre initialisation. + * See https://docs.qmk.fm/#/custom_quantum_functions?id=example-keyboard_pre_init_user-implementation + */ +void keyboard_pre_init_user(void) { + // Call the keyboard pre init code. + + // Set our LED pins as output + setPinOutput(C3); +} + +void matrix_init_kb(void) { + + // Flash the led 1 sec on startup. + writePinHigh(C3); + wait_ms(1000); + writePinLow(C3); +} diff --git a/keyboards/handwired/aek64/aek64.h b/keyboards/handwired/aek64/aek64.h new file mode 100644 index 0000000000..6378448760 --- /dev/null +++ b/keyboards/handwired/aek64/aek64.h @@ -0,0 +1,34 @@ +/* +Copyright 2012,2013 Jun Wako <wakojun@gmail.com> <4sStylZ@protonmail.ch> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#pragma once + +#include "quantum.h" + +/* Alps64 physical definition macro */ +#define LAYOUT( \ + k00, k01, k02, k03 , k04 , k05 , k06, k07 , k08 , k09 , k010 , k011, k012, k013 , \ + k10, k11, k12, k13 , k14 , k15 , k16, k17 , k18 , k19 , k110 , k111, k112, \ + k20, k21, k22, k23 , k24 , k25 , k26, k27 , k28 , k29 , k210 , k211, k212, k213 , \ + k30, k31, k32, k33 , k34 , k35 , k36, k37 , k38 , k39 , k310 , k311, k312, \ + k40, k41, k42, k46, k411, k412, k413 \ +) { \ + { k00, k01, k02, k03 , k04 , k05 , k06, k07 , k08 , k09 , k010 , k011, k012, k013 }, \ + { k10, k11, k12, k13 , k14 , k15 , k16, k17 , k18 , k19 , k110 , k111, k112, KC_NO }, \ + { k20, k21, k22, k23 , k24 , k25 , k26, k27 , k28 , k29 , k210 , k211, k212, k213 }, \ + { k30, k31, k32, k33 , k34 , k35 , k36, k37 , k38 , k39 , k310 , k311, k312, KC_NO }, \ + { k40, k41, k42, KC_NO, KC_NO, KC_NO, k46, KC_NO, KC_NO, KC_NO, KC_NO, k411, k412, k413 }, \ +} diff --git a/keyboards/handwired/aek64/config.h b/keyboards/handwired/aek64/config.h new file mode 100644 index 0000000000..45ce6665bc --- /dev/null +++ b/keyboards/handwired/aek64/config.h @@ -0,0 +1,78 @@ +/* +Copyright 2015 Jun Wako <wakojun@gmail.com> <4sStylZ@protonmail.ch> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6464 +#define DEVICE_VER 0x0001 +#define MANUFACTURER 4sStylZ and others makers +#define PRODUCT AEK64 +#define DESCRIPTION QMK keyboard firmware for AEK64 handwired + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +// Originally made for a Teensy 2++ +#define MATRIX_COL_PINS { F0, E6, E7, B0, B1, B2, B3, B4, B5, B6, B7, D0, D1, D2 } +#define MATRIX_ROW_PINS { E0, E1, C0, C1, C2 } +#define UNUSED_PINS + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +// #define LOCKING_SUPPORT_ENABLE + +/* Locking resynchronize hack */ +//#define LOCKING_RESYNC_ENABLE + +/* Enable the space-cadet options */ +#define RSPC_KEYS KC_RSFT, KC_TRNS, KC_PGUP +#define RCPC_KEYS KC_RCTL, KC_TRNS, KC_PGDOWN +#define LSPO_KEYS KC_LSFT, KC_TRNS, KC_HOME +#define LCPO_KEYS KC_LCTL, KC_TRNS, KC_END + +/* Enable double tab */ +#define TAPPING_TERM 175 + +#define COMBO_COUNT 1 + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION diff --git a/keyboards/handwired/aek64/info.json b/keyboards/handwired/aek64/info.json new file mode 100644 index 0000000000..4665b46387 --- /dev/null +++ b/keyboards/handwired/aek64/info.json @@ -0,0 +1,12 @@ +{ + "keyboard_name": "aek64", + "url": "", + "maintainer": "qmk", + "width": 14.75, + "height": 5, + "layouts": { + "LAYOUT": { + "layout": [{"label":"Esc", "x":0, "y":0, "w":1.25}, {"label":"1", "x":1.25, "y":0}, {"label":"2", "x":2.25, "y":0}, {"label":"3", "x":3.25, "y":0}, {"label":"4", "x":4.25, "y":0}, {"label":"5", "x":5.25, "y":0}, {"label":"6", "x":6.25, "y":0}, {"label":"7", "x":7.25, "y":0}, {"label":"8", "x":8.25, "y":0}, {"label":"9", "x":9.25, "y":0}, {"label":"0", "x":10.25, "y":0}, {"label":"\u00b0", "x":11.25, "y":0}, {"label":"+", "x":12.25, "y":0}, {"label":"Backspace", "x":13.25, "y":0, "w":1.75}, {"label":"Tab", "x":0, "y":1, "w":1.75}, {"label":"A", "x":1.75, "y":1}, {"label":"Z", "x":2.75, "y":1}, {"label":"E", "x":3.75, "y":1}, {"label":"R", "x":4.75, "y":1}, {"label":"T", "x":5.75, "y":1}, {"label":"Y", "x":6.75, "y":1}, {"label":"U", "x":7.75, "y":1}, {"label":"I", "x":8.75, "y":1}, {"label":"O", "x":9.75, "y":1}, {"label":"P", "x":10.75, "y":1}, {"label":"{", "x":11.75, "y":1}, {"label":"}", "x":12.75, "y":1}, {"label":"Caps Lock", "x":0, "y":2, "w":2}, {"label":"Q", "x":2, "y":2}, {"label":"S", "x":3, "y":2}, {"label":"D", "x":4, "y":2}, {"label":"F", "x":5, "y":2}, {"label":"G", "x":6, "y":2}, {"label":"H", "x":7, "y":2}, {"label":"J", "x":8, "y":2}, {"label":"K", "x":9, "y":2}, {"label":"L", "x":10, "y":2}, {"label":"M", "x":11, "y":2}, {"label":"%", "x":12, "y":2}, {"label":"µ", "x":13, "y":2}, {"label":"Enter", "x":14, "y":1, "h":2}, {"label":"Shift", "x":0, "y":3, "w":1.5}, {"label":">", "x":1.5, "y":3}, {"label":"W", "x":2.5, "y":3}, {"label":"X", "x":3.5, "y":3}, {"label":"C", "x":4.5, "y":3}, {"label":"V", "x":5.5, "y":3}, {"label":"B", "x":6.5, "y":3}, {"label":"N", "x":7.5, "y":3}, {"label":"?", "x":8.5, "y":3}, {"label":".", "x":9.5, "y":3}, {"label":"/", "x":10.5, "y":3}, {"label":"§", "x":11.5, "y":3}, {"label":"Shift", "x":12.5, "y":3, "w":2.5}, {"label":"Ctrl", "x":0, "y":4, "w":1.5}, {"label":"Opt", "x":1.5, "y":4, "w":1.25}, {"label":"Cmd", "x":2.75, "y":4, "w":1.5}, {"label":"Space", "x":4.25, "y":4, "w":6.5}, {"label":"Cmd", "x":10.75, "y":4, "w":1.5}, {"label":"Opt", "x":12.25, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.5, "y":4, "w":1.5}] + } + } +} diff --git a/keyboards/handwired/aek64/keymaps/4sstylz/keymap.c b/keyboards/handwired/aek64/keymaps/4sstylz/keymap.c new file mode 100644 index 0000000000..65f8354aab --- /dev/null +++ b/keyboards/handwired/aek64/keymaps/4sstylz/keymap.c @@ -0,0 +1,102 @@ +#include QMK_KEYBOARD_H + +// Implement Super-alt↯tab +// See https://docs.qmk.fm/#/feature_macros?id=super-alt↯tab +bool is_alt_tab_active = false; +uint16_t alt_tab_timer = 0; + +// Defining all the custom keycodes. +enum custom_keycodes { + ALT_TAB = SAFE_RANGE +}; + +const uint16_t PROGMEM lock_combo[] = {KC_J, KC_K, KC_L, KC_SCLN, COMBO_END}; +combo_t key_combos[COMBO_COUNT] = {COMBO(lock_combo, LGUI(KC_O))}; + +// Define the keycodes for one qwerty layer and one Fn layer. +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* 0: qwerty + * ┌──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬─────────────┐ + * │ ` Esc│ 1 │ 2 │ 3 │ 4 │ 5 │ 6 │ 7 │ 8 │ 9 │ 0 │ - │ = │ Bksp │ + * ├─────────────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┬───────┤ + * │ Tab │ Q │ W │ E │ R │ T │ Y │ U │ I │ O │ P │ [ │ ] │ │ + * ├─────────────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┴┐ Enter│ + * │ Layer 2 │ A │ S │ D │ F │ G │ H │ J │ K │ L │ ; │ ' │ # │ │ + * ├──────┬──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┴──────┴──────┤ + * │ Shift│ \ │ Z │ X │ C │ V │ B │ N │ M │ , │ . │ / │ Shift │ + * ├──────┼──────┼──────┼──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┼──────┬──────┬──────┤ + * │ Ctrl │ Alt │↯ATab │ Space │ Gui │ Alt │ Ctrl │ + * └──────┴──────┴──────┴──────────────────────────────────────────────────────────────┴──────┴──────┴──────┘ + * + * Hidden features : + * - Left Shift is also Home on a single tap. + * - Left Ctrl is also End on a single tap. + * - Right Shift is also page-up on a single tap. + * - Right Ctrl is also page-down on a single tap. + * - Press JKLM for Windows + L (Session lock) + */ + [0] = LAYOUT( \ + KC_GESC , KC_1 , KC_2 , KC_3 , KC_4 , KC_5 , KC_6 , KC_7 , KC_8 , KC_9 , KC_0 , KC_MINS, KC_EQL , KC_BSPC, + KC_TAB , KC_Q , KC_W , KC_E , KC_R , KC_T , KC_Y , KC_U , KC_I , KC_O , KC_P , KC_LBRC, KC_RBRC, + MO(1) , KC_A , KC_S , KC_D , KC_F , KC_G , KC_H , KC_J , KC_K , KC_L , KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT , + KC_LSPO , KC_NUBS, KC_Z , KC_X , KC_C , KC_V , KC_B , KC_N , KC_M , KC_COMM, KC_DOT , KC_SLSH, KC_RSPC , + KC_LCPO , KC_LALT, ALT_TAB, KC_SPC, KC_LGUI, KC_RALT, KC_RCPC + ), + + /* 1: second layer for media keys and many advanced features ç + * ┌──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬─────────────┐ + * │Alt F4│ F1 │ F2 │ F3 │ F4 │ F5 │ F6 │ F7 │ F8 │ F9 │ F10 │ F11 │ F12 │ │ + * ├──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┬───────┤ + * │ │ │ │PrtScn│ Brt+ │ Brt- │Ctrl A│ Home │ Up │ End │ ‽ │ ↑ │ ⸮ │ │ │ + * ├─────────────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┴┐ │ + * │ │ Cut │ Copy │Paste │ Del │ Del │ Left │ Down │Right │ ← │ ↓ │ → │ │ │ + * ├──────┬──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┴──────┴──────┤ + * │ │ │ Mute │ Vol- │ Vol+ │ │ │ │ │ │ │Reset │ │ + * ├──────┼──────┼──────┼──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┼──────┬──────┬──────┤ + * │ │ │ │ │ │ │ │ + * └──────┴──────┴──────┴──────────────────────────────────────────────────────────────┴──────┴──────┴──────┘ + */ + [1] = LAYOUT( \ + LALT(KC_F4), KC_F1 , KC_F2 , KC_F3 , KC_F4 , KC_F5 , KC_F6 , KC_F7 , KC_F8 , KC_F9 , KC_F10 , KC_F11 , KC_F12 , _______, + _______ , _______ , _______ , KC_PSCR , KC_BRIU , KC_BRID, LCTL(KC_A), KC_HOME, KC_UP , KC_END , UC(0x203D) , UC(0x8593), UC(0x2E2E), + _______ , _______ , LSFT(KC_DEL), LCTL(KC_INS), LSFT(KC_INS), KC_DEL , KC_DEL , KC_LEFT, KC_DOWN, KC_RIGHT, UC(0x8592) , UC(0x8595), UC(0x8594), _______, + _______ , _______ , KC_MUTE , KC_VOLD , KC_VOLU , _______, _______ , _______, _______, _______ , _______ , RESET , _______ , + _______ , _______ , _______ , _______, _______ , _______ , _______ + ) +}; + +// Set the unicode input mode for using UC. +void matrix_init_user(void) { + set_unicode_input_mode(UC_LNX); +} + +// Processing all the key pressed. +// Alt+tab. +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + + // Depending keycodes… + switch (keycode) { // This will do most of the grunt work with the keycodes. + case ALT_TAB: + if (record->event.pressed) { + if (!is_alt_tab_active) { + is_alt_tab_active = true; + register_code(KC_LALT); + } + alt_tab_timer = timer_read(); + register_code(KC_TAB); + } else { + unregister_code(KC_TAB); + } + break; + } + return true; +} + +void matrix_scan_user(void) { // The very important timer. + if (is_alt_tab_active) { + if (timer_elapsed(alt_tab_timer) > 750) { + unregister_code(KC_LALT); + is_alt_tab_active = false; + } + } +} diff --git a/keyboards/handwired/aek64/keymaps/default/keymap.c b/keyboards/handwired/aek64/keymaps/default/keymap.c new file mode 100644 index 0000000000..5b9115902d --- /dev/null +++ b/keyboards/handwired/aek64/keymaps/default/keymap.c @@ -0,0 +1,53 @@ +#include QMK_KEYBOARD_H + +// Define the keycodes for one qwerty layer and one Fn layer. +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* 0: qwerty + * ┌──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬─────────────┐ + * │ ` Esc│ 1 │ 2 │ 3 │ 4 │ 5 │ 6 │ 7 │ 8 │ 9 │ 0 │ - │ = │ Bksp │ + * ├─────────────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┬───────┤ + * │ Tab │ Q │ W │ E │ R │ T │ Y │ U │ I │ O │ P │ [ │ ] │ │ + * ├─────────────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┴┐ Enter│ + * │ Layer 2 │ A │ S │ D │ F │ G │ H │ J │ K │ L │ ; │ ' │ # │ │ + * ├──────┬──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┴──────┴──────┤ + * │ Shift│ \ │ Z │ X │ C │ V │ B │ N │ M │ , │ . │ / │ Shift │ + * ├──────┼──────┼──────┼──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┼──────┬──────┬──────┤ + * │ Ctrl │ Alt │ Gui │ Space │ Gui │ Alt │ Ctrl │ + * └──────┴──────┴──────┴──────────────────────────────────────────────────────────────┴──────┴──────┴──────┘ + * + * Hidden features : + * - Left Shift is also Home on a single tap. + * - Left Ctrl is also End on a single tap. + * - Right Shift is also page-up on a single tap. + * - Right Ctrl is also page-down on a single tap. + * - Press JKLM for Windows + L (Session lock) + */ + [0] = LAYOUT( + KC_ESC , KC_1 , KC_2 , KC_3 , KC_4 , KC_5 , KC_6 , KC_7 , KC_8 , KC_9 , KC_0 , KC_MINS, KC_EQL , KC_BSPC, + KC_TAB , KC_Q , KC_W , KC_E , KC_R , KC_T , KC_Y , KC_U , KC_I , KC_O , KC_P , KC_LBRC, KC_RBRC, + MO(1) , KC_A , KC_S , KC_D , KC_F , KC_G , KC_H , KC_J , KC_K , KC_L , KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT , + KC_LSPO, KC_NUBS, KC_Z , KC_X , KC_C , KC_V , KC_B , KC_N , KC_M , KC_COMM, KC_DOT , KC_SLSH, KC_RSPC , + KC_LCPO, KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT, KC_RCPC + ), + + /* 1: second layer for media keys and many advanced features ç + * ┌──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬──────┬─────────────┐ + * │Alt F4│ F1 │ F2 │ F3 │ F4 │ F5 │ F6 │ F7 │ F8 │ F9 │ F10 │ F11 │ F12 │ │ + * ├──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┬───────┤ + * │ │ │ │ │ │ │Ctrl A│ Home │ Up │ End │ │ │ │ │ │ + * ├─────────────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼─────┴┐ │ + * │ │ Cut │ Copy │Paste │ Del │ Del │ Left │ Down │Right │ │ │ │ │ │ + * ├──────┬──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┼──────┴──────┴──────┤ + * │ │ │ Mute │ Vol- │ Vol+ │ │ │ │ │ │ │Reset │ │ + * ├──────┼──────┼──────┼──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┴──────┼──────┬──────┬──────┤ + * │ │ │ │ │ │ │ │ + * └──────┴──────┴──────┴──────────────────────────────────────────────────────────────┴──────┴──────┴──────┘ + */ + [1] = LAYOUT( + LALT(KC_F4), KC_F1 , KC_F2 , KC_F3 , KC_F4 , KC_F5 , KC_F6 , KC_F7 , KC_F8 , KC_F9 , KC_F10 , KC_F11 , KC_F12 , _______, + _______ , _______ , _______ , _______ , _______ , _______, LCTL(KC_A), KC_HOME, KC_UP , KC_END , _______ , _______ , _______ , + _______ , _______ , LSFT(KC_DEL), LCTL(KC_INS), LSFT(KC_INS), KC_DEL , KC_DEL , KC_LEFT, KC_DOWN, KC_RIGHT, _______ , _______ , _______ , _______, + _______ , _______ , KC_MUTE , KC_VOLD , KC_VOLU , _______, _______ , _______, _______, _______ , _______ , RESET , _______ , + _______ , _______ , _______ , _______, _______ , _______ , _______ + ) +}; diff --git a/keyboards/handwired/aek64/readme.md b/keyboards/handwired/aek64/readme.md new file mode 100644 index 0000000000..7afecca12c --- /dev/null +++ b/keyboards/handwired/aek64/readme.md @@ -0,0 +1,17 @@ +# AEK64 + +An Alps-only 60% handwired ISO AEK based on the original AEK plate. + +Keyboard Maintainer: QMK Community +Hardware Supported: AEK II ISO +Hardware Availability: buy an used one and salvage / cut the plate and rip-off the switchs. For the case, a GH60 can be good. + +Make example for this keyboard (after setting up your build environment): + + make aek64:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). + +# Known issues + +* The Unicode characters on the keymap don’t work. diff --git a/keyboards/handwired/aek64/rules.mk b/keyboards/handwired/aek64/rules.mk new file mode 100644 index 0000000000..c02af3dd6c --- /dev/null +++ b/keyboards/handwired/aek64/rules.mk @@ -0,0 +1,27 @@ +# MCU name +MCU = at90usb1286 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay + +# Build Options +# change to no to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = no # USB Nkey Rollover - not yet supported in LUFA +UNICODE_ENABLE = yes # Enable support for arrow keys icon on the second layer. +COMBO_ENABLE = yes # Enable combo for special function when using multiple keys at once. +TAP_DANCE_ENABLE = no # Enable use multiple tap +NKRO_ENABLE = yes diff --git a/keyboards/handwired/aranck/aranck.c b/keyboards/handwired/aranck/aranck.c new file mode 100644 index 0000000000..2e67ec1dae --- /dev/null +++ b/keyboards/handwired/aranck/aranck.c @@ -0,0 +1,43 @@ +/* Copyright 2019 Arda Kilicdagi + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "aranck.h" + +// Optional override functions below. +// You can leave any or all of these undefined. +// These are only required if you want to perform custom actions. + + + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +}
\ No newline at end of file diff --git a/keyboards/handwired/aranck/aranck.h b/keyboards/handwired/aranck/aranck.h new file mode 100644 index 0000000000..de7639fd03 --- /dev/null +++ b/keyboards/handwired/aranck/aranck.h @@ -0,0 +1,39 @@ +/* Copyright 2019 Arda Kilicdagi + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT_aranck_mit(\ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a \ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \ + { k30, k31, k32, k33, k34, KC_NO, k35, k36, k37, k38, k39, k3a } \ +} diff --git a/keyboards/handwired/aranck/config.h b/keyboards/handwired/aranck/config.h new file mode 100644 index 0000000000..5212409c8d --- /dev/null +++ b/keyboards/handwired/aranck/config.h @@ -0,0 +1,262 @@ +/* +Copyright 2019 Arda Kilicdagi + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Ardakilic +#define PRODUCT ARANCK +#define DESCRIPTION A handwired 40% ortholinear keyboard + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS \ + { D3, D2, D1, D0 } +#define MATRIX_COL_PINS \ + { C6, D7, E6, B4, B6, B2, B3, B1, F7, F6, F5, F4 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +/* + * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN. + */ +// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6 + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + +// #define RGB_DI_PIN E2 +// #ifdef RGB_DI_PIN +// #define RGBLED_NUM 16 +// #define RGBLIGHT_HUE_STEP 8 +// #define RGBLIGHT_SAT_STEP 8 +// #define RGBLIGHT_VAL_STEP 8 +// #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ +// #define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ +// /*== all animations enable ==*/ +// #define RGBLIGHT_ANIMATIONS +// /*== or choose animations ==*/ +// #define RGBLIGHT_EFFECT_BREATHING +// #define RGBLIGHT_EFFECT_RAINBOW_MOOD +// #define RGBLIGHT_EFFECT_RAINBOW_SWIRL +// #define RGBLIGHT_EFFECT_SNAKE +// #define RGBLIGHT_EFFECT_KNIGHT +// #define RGBLIGHT_EFFECT_CHRISTMAS +// #define RGBLIGHT_EFFECT_STATIC_GRADIENT +// #define RGBLIGHT_EFFECT_RGB_TEST +// #define RGBLIGHT_EFFECT_ALTERNATING +// /*== customize breathing effect ==*/ +// /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ +// #define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 +// /*==== use exp() and sin() ====*/ +// #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 +// #define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 +// #endif + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + + +/** + * Aranck-specific definitions + */ +#define B5_AUDIO +/** + * Aranck-specific definitions END + */ + + +#define TAPPING_TERM 200 +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +/* defined by default; to change, uncomment and set to the combination you want */ +// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP H +//#define MAGIC_KEY_HELP_ALT SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER0_ALT GRAVE +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER B +//#define MAGIC_KEY_BOOTLOADER_ALT ESC +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_EEPROM_CLEAR BSPACE +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +/* + * HD44780 LCD Display Configuration + */ +/* +#define LCD_LINES 2 //< number of visible lines of the display +#define LCD_DISP_LENGTH 16 //< visibles characters per line of the display + +#define LCD_IO_MODE 1 //< 0: memory mapped mode, 1: IO port mode + +#if LCD_IO_MODE +#define LCD_PORT PORTB //< port for the LCD lines +#define LCD_DATA0_PORT LCD_PORT //< port for 4bit data bit 0 +#define LCD_DATA1_PORT LCD_PORT //< port for 4bit data bit 1 +#define LCD_DATA2_PORT LCD_PORT //< port for 4bit data bit 2 +#define LCD_DATA3_PORT LCD_PORT //< port for 4bit data bit 3 +#define LCD_DATA0_PIN 4 //< pin for 4bit data bit 0 +#define LCD_DATA1_PIN 5 //< pin for 4bit data bit 1 +#define LCD_DATA2_PIN 6 //< pin for 4bit data bit 2 +#define LCD_DATA3_PIN 7 //< pin for 4bit data bit 3 +#define LCD_RS_PORT LCD_PORT //< port for RS line +#define LCD_RS_PIN 3 //< pin for RS line +#define LCD_RW_PORT LCD_PORT //< port for RW line +#define LCD_RW_PIN 2 //< pin for RW line +#define LCD_E_PORT LCD_PORT //< port for Enable line +#define LCD_E_PIN 1 //< pin for Enable line +#endif +*/ + +/* Bootmagic Lite key configuration */ +// #define BOOTMAGIC_LITE_ROW 0 +// #define BOOTMAGIC_LITE_COLUMN 0 diff --git a/keyboards/handwired/aranck/info.json b/keyboards/handwired/aranck/info.json new file mode 100644 index 0000000000..450d89634a --- /dev/null +++ b/keyboards/handwired/aranck/info.json @@ -0,0 +1,62 @@ +{ + "keyboard_name": "Aranck", + "keyboard_folder": "handwired/aranck", + "url": "https://github.com/Ardakilic", + "maintainer": "Arda Kilicdagi", + "width": 12, + "height": 4, + "layouts": { + "LAYOUT_aranck_mit": { + "key_count": 47, + "layout": [ + { "x": 0, "y": 0 }, + { "x": 1, "y": 0 }, + { "x": 2, "y": 0 }, + { "x": 3, "y": 0 }, + { "x": 4, "y": 0 }, + { "x": 5, "y": 0 }, + { "x": 6, "y": 0 }, + { "x": 7, "y": 0 }, + { "x": 8, "y": 0 }, + { "x": 9, "y": 0 }, + { "x": 10, "y": 0 }, + { "x": 11, "y": 0 }, + { "x": 0, "y": 1 }, + { "x": 1, "y": 1 }, + { "x": 2, "y": 1 }, + { "x": 3, "y": 1 }, + { "x": 4, "y": 1 }, + { "x": 5, "y": 1 }, + { "x": 6, "y": 1 }, + { "x": 7, "y": 1 }, + { "x": 8, "y": 1 }, + { "x": 9, "y": 1 }, + { "x": 10, "y": 1 }, + { "x": 11, "y": 1 }, + { "x": 0, "y": 2 }, + { "x": 1, "y": 2 }, + { "x": 2, "y": 2 }, + { "x": 3, "y": 2 }, + { "x": 4, "y": 2 }, + { "x": 5, "y": 2 }, + { "x": 6, "y": 2 }, + { "x": 7, "y": 2 }, + { "x": 8, "y": 2 }, + { "x": 9, "y": 2 }, + { "x": 10, "y": 2 }, + { "x": 11, "y": 2 }, + { "x": 0, "y": 3 }, + { "x": 1, "y": 3 }, + { "x": 2, "y": 3 }, + { "x": 3, "y": 3 }, + { "x": 4, "y": 3 }, + { "x": 5, "y": 3, "w": 2 }, + { "x": 7, "y": 3 }, + { "x": 8, "y": 3 }, + { "x": 9, "y": 3 }, + { "x": 10, "y": 3 }, + { "x": 11, "y": 3 } + ] + } + } +} diff --git a/keyboards/handwired/aranck/keymaps/default/config.h b/keyboards/handwired/aranck/keymaps/default/config.h new file mode 100644 index 0000000000..cf888b0adc --- /dev/null +++ b/keyboards/handwired/aranck/keymaps/default/config.h @@ -0,0 +1,22 @@ +/* Copyright 2019 Arda Kilicdagi + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here + +// #define RETRO_TAPPING +// #define PERMISSIVE_HOLD
\ No newline at end of file diff --git a/keyboards/handwired/aranck/keymaps/default/keymap.c b/keyboards/handwired/aranck/keymaps/default/keymap.c new file mode 100644 index 0000000000..2765c7afbf --- /dev/null +++ b/keyboards/handwired/aranck/keymaps/default/keymap.c @@ -0,0 +1,178 @@ +/* Copyright 2019 Arda Kilicdagi + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + + +enum aranck_layers { + _QWERTY, + _LOWER, + _RAISE, + _ADJUST, + _SPACE, + _SODA, + _NUMPAD +}; + + +#define LOCKSCREEN LCTL(LSFT(KC_POWER)) // Screen Lock shortcut for OSX + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |NPdESC| A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |SftEtr| + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | PWR | Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = LAYOUT_aranck_mit( + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + LT(_NUMPAD, KC_ESC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, + LSFT_T(KC_CAPS), KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_SFTENT /*KC_ENT*/, + LT(_SODA, KC_POWER), KC_LCTL, KC_LALT, KC_LGUI, MO(_LOWER), LT(_SPACE, KC_SPC), MO(_RAISE), KC_LEFT, KC_DOWN, KC_UP, KC_RGHT +), + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO ~ |ISO | | Home | End | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = LAYOUT_aranck_mit( + KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC, + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE, + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, S(KC_NUHS), S(KC_NUBS), KC_HOME, KC_END, _______, + _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY +), + + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | - | = | [ | ] | \ | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO # |ISO / |Pg Up |Pg Dn | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = LAYOUT_aranck_mit( + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS, + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______, + _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY +), + +/* Soda Layer + * Keys that I mostly use when while chilling or taking a break :) + * ,-----------------------------------------------------------------------------------. + * | | | | | | | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | Mute | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | Next | Vol- | Vol+ | Play | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | |Brght▼|Brght▲| + * `-----------------------------------------------------------------------------------' + */ +[_SODA] = LAYOUT_aranck_mit( + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_MUTE, + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY, + _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRMD, KC_BRMU +), + +/* Space Layer (Space Bar Layer Tap) + * ,-----------------------------------------------------------------------------------. + * | |CMD+1 |CMD+2 |CMD+3 |CMD+4 |CMD+5 |CMD+6 |CMD+7 |CMD+8 |CMD+9 |CMD+0 |LCKOSX| + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | Up | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | Left | Down | Right| | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | |Brght▼|Brght▲| + * `-----------------------------------------------------------------------------------' + */ +[_SPACE] = LAYOUT_aranck_mit( + _______, LGUI(KC_1), LGUI(KC_2), LGUI(KC_3), LGUI(KC_4), LGUI(KC_5), LGUI(KC_6), LGUI(KC_7), LGUI(KC_8), LGUI(KC_9), LGUI(KC_0), LOCKSCREEN, + _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_UP, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRMD, KC_BRMU +), + +/* Numpad Layer + * ,-----------------------------------------------------------------------------------. + * | | | | | | | | 7 | 8 | 9 | - | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | Enter| 4 | 5 | 6 | + | * | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | 1 | 2 | 3 | + | / | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | 0 | 0 | . | , | = | + * `-----------------------------------------------------------------------------------' + */ +[_NUMPAD] = LAYOUT_aranck_mit( + _______, _______, _______, _______, _______, _______, _______, KC_P7, KC_P8, KC_P9, KC_PMNS, KC_BSPC, + _______, _______, _______, _______, _______, _______, KC_PENT, KC_P4, KC_P5, KC_P6, KC_PPLS, KC_PAST, + _______, _______, _______, _______, _______, _______, _______, KC_P1, KC_P2, KC_P3, KC_PPLS, KC_PSLS, + _______, _______, _______, _______, _______, _______, KC_P0, KC_P0, KC_PDOT, KC_PCMM, KC_PEQL +), + + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | Reset|EEPRst| | | | | | | | | Del | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | |MUSmod|Aud on|Audoff| | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | |Voice-|Voice+|Mus on|Musoff| | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = LAYOUT_aranck_mit( + _______, RESET, EEP_RST, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL, + _______, _______, MU_MOD, AU_ON, AU_OFF, _______, _______, _______, _______, _______, _______, _______, + _______, MUV_DE, MUV_IN, MU_ON, MU_OFF, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ +) + +}; + +// Enable the adjust layer when both lower and +layer_state_t layer_state_set_user(layer_state_t state) { + return update_tri_layer_state(state, _LOWER, _RAISE, _ADJUST); +} + +//bool process_record_user(uint16_t keycode, keyrecord_t *record) { +// return true; +//} + +void matrix_init_user(void) {} + +void matrix_scan_user(void) {} + +void led_set_user(uint8_t usb_led) {} diff --git a/keyboards/handwired/aranck/keymaps/default/readme.md b/keyboards/handwired/aranck/keymaps/default/readme.md new file mode 100644 index 0000000000..ba7ddbdd33 --- /dev/null +++ b/keyboards/handwired/aranck/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for Aranck diff --git a/keyboards/handwired/aranck/keymaps/turkishish/config.h b/keyboards/handwired/aranck/keymaps/turkishish/config.h new file mode 100644 index 0000000000..3e40ef4f6d --- /dev/null +++ b/keyboards/handwired/aranck/keymaps/turkishish/config.h @@ -0,0 +1,22 @@ +/* Copyright 2019 Arda Kilicdagi + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here + +#define RETRO_TAPPING +#define PERMISSIVE_HOLD
\ No newline at end of file diff --git a/keyboards/handwired/aranck/keymaps/turkishish/keymap.c b/keyboards/handwired/aranck/keymaps/turkishish/keymap.c new file mode 100644 index 0000000000..195b8aaad0 --- /dev/null +++ b/keyboards/handwired/aranck/keymaps/turkishish/keymap.c @@ -0,0 +1,225 @@ +/* Copyright 2019 Arda Kilicdagi + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + + +enum aranck_layers { + _QWERTY, + _LOWER, + _RAISE, + _ADJUST, + _SPACE, + _SODA, + _NUMPAD +}; + +//KC_NONUS_BSLASH (\|) is equivalent to ["é] key in Turkish keyboards. +//KC_GRV (~ `) is equivalent to [<>|] key in Turkish keyboards. +// KC_SCLN is Turkish s [şŞ] key +// KC_QUOT is Turkish i [iİ] key +// KC_COMM is Turkish o [öÖ] key +// KC_DOT is Turkish c [çÇ] key + +// Custom shortcuts specific to Turkish layout +#define CURLY_OPEN RALT(KC_7) +#define CURLY_CLOSE RALT(KC_0) +#define SQUARE_OPEN RALT(KC_8) +#define SQUARE_CLOSE RALT(KC_9) +#define DOLLAR_SIGN RALT(KC_4) +#define BACKSLASH RALT(KC_MINS) +#define VERTICAL_PIPE RALT(KC_EQL) +#define BACKTICK RALT(KC_BSLS) +#define TILDE RALT(KC_RBRC) +#define LOCKSCREEN LCTL(LSFT(KC_POWER)) // Screen Lock shortcut for OSX + +/* +// Unicode Turkish characters, in case it's needed +enum { + TR_C, // ç + TR_C_L, // Ç + TR_I, // ı + TR_I_L, // İ + TR_G, // ğ + TR_G_L, // Ğ + TR_S, // ş + TR_S_L, // Ş + TR_U, // ü + TR_U_L, // Ü + TR_O, // ö + TR_O_L, // Ö +}; + +// clang-format off +const uint32_t PROGMEM unicode_map[] = { + [TR_C] = 0x00c7, + [TR_C_L] = 0x00e7, + [TR_I] = 0x0130, + [TR_I_L] = 0x0131, + [TR_G] = 0x011e, + [TR_G_L] = 0x011f, + [TR_S] = 0x015e, + [TR_S_L] = 0x015f, + [TR_U] = 0x00dc, + [TR_U_L] = 0x00fc, + [TR_O] = 0x00d6, + [TR_O_L] = 0x00f6, +}; +// clang-format on +*/ + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |NPdEsc| A | S | D | F | G | H | J | K | L | Ş | İ | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |SftCps| Z | X | C | V | B | N | M | Ö | Ç | . |SftEtr| + * |------+------+------+------+------+------+------+------+------+------+------+------| + * |Sda|<>| Ctrl | Alt | OS |Lowr|,| Space* |Rise|"| Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = LAYOUT_aranck_mit( + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + LT(_NUMPAD, KC_ESC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, + LSFT_T(KC_CAPS), KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_SFTENT /*KC_ENT*/, + LT(_SODA, KC_GRV), KC_LCTL, KC_LALT, KC_LGUI, LT(_LOWER, KC_BSLS), LT(_SPACE, KC_SPC), LT(_RAISE, KC_NONUS_BSLASH), KC_LEFT, KC_DOWN, KC_UP, KC_RGHT +), + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | > | ! | ' | ^ | + | % | & | / | ( | ) | = | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | ? | _ | Ğ | Ü | - | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 | "$" | "{" | "}" | , | ">" | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | "[" | "]" | ' | " | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = LAYOUT_aranck_mit( + KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC, + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LBRC, KC_RBRC, KC_EQL, + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, DOLLAR_SIGN, CURLY_OPEN, CURLY_CLOSE, KC_BSLS, LSFT(KC_GRV), + _______, _______, _______, _______, _______, _______, _______, SQUARE_OPEN, SQUARE_CLOSE, LSFT(KC_2), KC_NONUS_BSLASH +), + + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | <>| | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | * | - | "\" | "|" | , | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 | , | " | "~" | "`" | <>| | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = LAYOUT_aranck_mit( + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, BACKSLASH, VERTICAL_PIPE, KC_BSLS, + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_NUHS, KC_NUBS, TILDE, BACKTICK, KC_GRV, + _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY +), + +/* Soda Layer + * ,-----------------------------------------------------------------------------------. + * | | | | | | | | | Up | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Left | Down |Right | | Mute | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | Next | Vol- | Vol+ | Play | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | |Brght▼|Brght▲| + * `-----------------------------------------------------------------------------------' + */ +[_SODA] = LAYOUT_aranck_mit( + _______, _______, _______, _______, _______, _______, _______, _______, KC_UP, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, KC_MUTE, + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY, + _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRMD, KC_BRMU +), + +/* Space Layer (Space Bar Layer Tap) + * ,-----------------------------------------------------------------------------------. + * | |CMD+1 |CMD+2 |CMD+3 |CMD+4 |CMD+5 |CMD+6 |CMD+7 |CMD+8 |CMD+9 |CMD+0 |LCKOSX| + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | Up | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | Left | Down |Right | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | |Brght▼|Brght▲| + * `-----------------------------------------------------------------------------------' + */ +[_SPACE] = LAYOUT_aranck_mit( + _______, LGUI(KC_1), LGUI(KC_2), LGUI(KC_3), LGUI(KC_4), LGUI(KC_5), LGUI(KC_6), LGUI(KC_7), LGUI(KC_8), LGUI(KC_9), LGUI(KC_0), LOCKSCREEN, + _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_UP, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_RGHT, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRMD, KC_BRMU +), + + +/* Numpad Layer + * KC_PDOT is comma on the Turkish layout ¯\_(ツ)_/¯ + * ,-----------------------------------------------------------------------------------. + * | | | | | | | | 7 | 8 | 9 | - | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | Enter| 4 | 5 | 6 | + | * | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | 1 | 2 | 3 | + | / | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | 0 | 0 | . | , | = | + * `-----------------------------------------------------------------------------------' + */ +[_NUMPAD] = LAYOUT_aranck_mit( + _______, _______, _______, _______, _______, _______, _______, KC_P7, KC_P8, KC_P9, KC_PMNS, KC_BSPC, + _______, _______, _______, _______, _______, _______, KC_PENT, KC_P4, KC_P5, KC_P6, KC_PPLS, KC_PAST, + _______, _______, _______, _______, _______, _______, _______, KC_P1, KC_P2, KC_P3, KC_PPLS, KC_PSLS, + _______, _______, _______, _______, _______, _______, KC_P0, KC_P0, KC_SLSH, KC_PDOT, KC_PEQL +), + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | | Reset|EEPRom| | | | | | | | | Del | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | |MUSmod|Aud on|Audoff| | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | |Voice-|Voice+|Mus on|Musoff| | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = LAYOUT_aranck_mit( + _______, RESET, EEP_RST, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL, + _______, _______, MU_MOD, AU_ON, AU_OFF, _______, _______, _______, _______, _______, _______, _______, + _______, MUV_DE, MUV_IN, MU_ON, MU_OFF, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ +) + +}; + +// Enable the adjust layer when both lower and +layer_state_t layer_state_set_user(layer_state_t state) { + return update_tri_layer_state(state, _LOWER, _RAISE, _ADJUST); +} + +void matrix_init_user(void) {} + +void matrix_scan_user(void) {} + +void led_set_user(uint8_t usb_led) {} diff --git a/keyboards/handwired/aranck/keymaps/turkishish/readme.md b/keyboards/handwired/aranck/keymaps/turkishish/readme.md new file mode 100644 index 0000000000..8998081c1f --- /dev/null +++ b/keyboards/handwired/aranck/keymaps/turkishish/readme.md @@ -0,0 +1 @@ +# The Turkishish keymap for Aranck diff --git a/keyboards/handwired/aranck/readme.md b/keyboards/handwired/aranck/readme.md new file mode 100644 index 0000000000..67089b4997 --- /dev/null +++ b/keyboards/handwired/aranck/readme.md @@ -0,0 +1,22 @@ +# Aranck + + + + + +A handwired 40% ortholinear keyboard. + +The story: https://imgur.com/a/4QI7ifJ + +Keyboard Maintainer: [Arda Kilicdagi](https://github.com/ardakilic) +Hardware Supported: Pro Micro + +Make example for this keyboard (after setting up your build environment): + + make handwired/aranck:default:flash + +You can flash the "turkishish" layout (which I'm currently using) like: + + make handwired/aranck:turkishish:flash + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
\ No newline at end of file diff --git a/keyboards/handwired/aranck/rules.mk b/keyboards/handwired/aranck/rules.mk new file mode 100644 index 0000000000..b95b98a4c7 --- /dev/null +++ b/keyboards/handwired/aranck/rules.mk @@ -0,0 +1,33 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = yes # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
\ No newline at end of file diff --git a/keyboards/handwired/arrow_pad/rules.mk b/keyboards/handwired/arrow_pad/rules.mk index a03f0836b2..65fc42a062 100644 --- a/keyboards/handwired/arrow_pad/rules.mk +++ b/keyboards/handwired/arrow_pad/rules.mk @@ -1,54 +1,15 @@ - - # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable @@ -67,4 +28,4 @@ BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6
\ No newline at end of file +AUDIO_ENABLE = no # Audio output on port C6 diff --git a/keyboards/handwired/atreus50/rules.mk b/keyboards/handwired/atreus50/rules.mk index 21c4704e0d..e8b551fbb7 100644 --- a/keyboards/handwired/atreus50/rules.mk +++ b/keyboards/handwired/atreus50/rules.mk @@ -1,52 +1,15 @@ - - # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/handwired/chiron/chiron.c b/keyboards/handwired/chiron/chiron.c new file mode 100644 index 0000000000..997cda6a4d --- /dev/null +++ b/keyboards/handwired/chiron/chiron.c @@ -0,0 +1,16 @@ +/* Copyright 2019 Mike Hix + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "chiron.h" diff --git a/keyboards/handwired/chiron/chiron.h b/keyboards/handwired/chiron/chiron.h new file mode 100644 index 0000000000..9d1ab385a5 --- /dev/null +++ b/keyboards/handwired/chiron/chiron.h @@ -0,0 +1,42 @@ +/* Copyright 2019 Mike Hix + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +#define LAYOUT( \ + L00, L01, L02, L03, L04, L05, L06, R00, R01, R02, R03, R04, R05, R06, \ + L10, L11, L12, L13, L14, L15, L16, R10, R11, R12, R13, R14, R15, R16, \ + L20, L21, L22, L23, L24, L25, L26, R20, R21, R22, R23, R24, R25, R26, \ + L30, L31, L32, L33, L34, L35, L36, R30, R31, R32, R33, R34, R35, R36, \ + L40, L41, L42, L43, L44, L45, R40, R41, R42, R43, R44, R45 \ + ) \ + { \ + /* Left Half */ \ + { L06, L05, L04, L03, L02, L01, L00 }, \ + { L16, L15, L14, L13, L12, L11, L10 }, \ + { L26, L25, L24, L23, L22, L21, L20 }, \ + { L36, L35, L34, L33, L32, L31, L30 }, \ + { L45, L44, L43, KC_NO, L42, L41, L40 }, \ + /* Right Half */ \ + { R06, R05, R04, R03, R02, R01, R00 }, \ + { R16, R15, R14, R13, R12, R11, R10 }, \ + { R26, R25, R24, R23, R22, R21, R20 }, \ + { R36, R35, R34, R33, R32, R31, R30 }, \ + { R45, R44, R43, KC_NO, R42, R41, R40 } \ + } + +#define LAYOUT_chiron LAYOUT diff --git a/keyboards/handwired/chiron/config.h b/keyboards/handwired/chiron/config.h new file mode 100644 index 0000000000..fcc5ae49a6 --- /dev/null +++ b/keyboards/handwired/chiron/config.h @@ -0,0 +1,57 @@ +/* +Copyright 2019 Mike Hix + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Mike Hix +#define PRODUCT chiron +#define DESCRIPTION A custom keyboard + +#define MATRIX_ROWS 10 +#define MATRIX_COLS 7 + +// Pro Micro Pins 4, 6, 7, 8, 9 +#define MATRIX_ROW_PINS { D4, D7, E6, B4, B5 } +// Pro Micro Pins A3, A2, A1, A0, 15, 14, 16 +#define MATRIX_COL_PINS { F4, F5, F6, F7, B1, B3, B2 } + +#define UNUSED_PINS + +// Pro Micro Pins RX1 +#define SPLIT_HAND_PIN D2 + +// Pro Micro Pins RX1 +#define SOFT_SERIAL_PIN D0 + +#define DIODE_DIRECTION COL2ROW + +#define DEBOUNCE 5 + +#define LOCKING_SUPPORT_ENABLE +#define LOCKING_RESYNC_ENABLE + +#define RGB_DI_PIN D3 +#define RGBLED_NUM 4 + +#define BACKLIGHT_PIN B6 +#define BACKLIGHT_LEVELS 7 + diff --git a/keyboards/handwired/chiron/info.json b/keyboards/handwired/chiron/info.json new file mode 100644 index 0000000000..85aba1b43f --- /dev/null +++ b/keyboards/handwired/chiron/info.json @@ -0,0 +1,81 @@ +{ + "keyboard_name": "Chiron Keyboard", + "url": "", + "maintainer": "musl", + "width": 15, + "height": 5, + "layouts": { + "LAYOUT": { + "layout": [ + {"label":"L00", "x":0, "y":0}, + {"label":"L01", "x":1, "y":0}, + {"label":"L02", "x":2, "y":0}, + {"label":"L03", "x":3, "y":0}, + {"label":"L04", "x":4, "y":0}, + {"label":"L05", "x":5, "y":0}, + {"label":"L06", "x":6, "y":0}, + {"label":"R00", "x":8, "y":0}, + {"label":"R01", "x":9, "y":0}, + {"label":"R02", "x":10, "y":0}, + {"label":"R03", "x":11, "y":0}, + {"label":"R04", "x":12, "y":0}, + {"label":"R05", "x":13, "y":0}, + {"label":"R06", "x":14, "y":0}, + {"label":"L10", "x":0, "y":1}, + {"label":"L11", "x":1, "y":1}, + {"label":"L12", "x":2, "y":1}, + {"label":"L13", "x":3, "y":1}, + {"label":"L14", "x":4, "y":1}, + {"label":"L15", "x":5, "y":1}, + {"label":"L16", "x":6, "y":1}, + {"label":"R10", "x":8, "y":1}, + {"label":"R11", "x":9, "y":1}, + {"label":"R12", "x":10, "y":1}, + {"label":"R13", "x":11, "y":1}, + {"label":"R14", "x":12, "y":1}, + {"label":"R15", "x":13, "y":1}, + {"label":"R16", "x":14, "y":1}, + {"label":"L20", "x":0, "y":2}, + {"label":"L21", "x":1, "y":2}, + {"label":"L22", "x":2, "y":2}, + {"label":"L23", "x":3, "y":2}, + {"label":"L24", "x":4, "y":2}, + {"label":"L25", "x":5, "y":2}, + {"label":"L26", "x":6, "y":2}, + {"label":"R20", "x":8, "y":2}, + {"label":"R21", "x":9, "y":2}, + {"label":"R22", "x":10, "y":2}, + {"label":"R23", "x":11, "y":2}, + {"label":"R24", "x":12, "y":2}, + {"label":"R25", "x":13, "y":2}, + {"label":"R26", "x":14, "y":2}, + {"label":"L30", "x":0, "y":3}, + {"label":"L31", "x":1, "y":3}, + {"label":"L32", "x":2, "y":3}, + {"label":"L33", "x":3, "y":3}, + {"label":"L34", "x":4, "y":3}, + {"label":"L35", "x":5, "y":3}, + {"label":"L36", "x":6, "y":3}, + {"label":"R30", "x":8, "y":3}, + {"label":"R31", "x":9, "y":3}, + {"label":"R32", "x":10, "y":3}, + {"label":"R33", "x":11, "y":3}, + {"label":"R34", "x":12, "y":3}, + {"label":"R35", "x":13, "y":3}, + {"label":"R36", "x":14, "y":3}, + {"label":"L40", "x":0, "y":4}, + {"label":"L41", "x":1, "y":4}, + {"label":"L42", "x":2, "y":4}, + {"label":"L43", "x":4, "y":4, "h":1.25}, + {"label":"L44", "x":5, "y":4, "h":1.25}, + {"label":"L45", "x":6, "y":4, "h":1.25}, + {"label":"R40", "x":8, "y":4, "h":1.25}, + {"label":"R41", "x":9, "y":4, "h":1.25}, + {"label":"R42", "x":10, "y":4, "h":1.25}, + {"label":"R43", "x":12, "y":4}, + {"label":"R44", "x":13, "y":4}, + {"label":"R45", "x":14, "y":4} + ] + } + } +} diff --git a/keyboards/handwired/chiron/keymaps/default/config.h b/keyboards/handwired/chiron/keymaps/default/config.h new file mode 100644 index 0000000000..08134a720b --- /dev/null +++ b/keyboards/handwired/chiron/keymaps/default/config.h @@ -0,0 +1,52 @@ +/* Copyright 2019 Mike Hix + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#define USE_SERIAL +#define MASTER_RIGHT +//#define MASTER_LEFT + +#define IGNORE_MOD_TAP_INTERRUPT +#define PERMISSIVE_HOLD + +#define TAPPING_TERM 200 + +#define MOUSEKEY_DELAY 20 +#define MOUSEKEY_INTERVAL 20 +#define MOUSEKEY_MAX_SPEED 10 +#define MOUSEKEY_TIME_TO_MAX 30 +#define MOUSEKEY_WHEEL_MAX_SPEED 8 +#define MOUSEKEY_WHEEL_TIME_TO_MAX 40 + +#undef RGBLED_NUM +#define RGBLED_NUM 2 +#define RGBLED_SPLIT {1, 1} + +// Don't turn off lights when the host goes to sleep. +#undef RGBLIGHT_SLEEP + +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 + +// Selectively enable animations to save on code size. +#undef RGBLIGHT_ANIMATIONS +#define RGBLIGHT_EFFECT_BREATHING +#define RGBLIGHT_EFFECT_BREATHING +#define RGBLIGHT_EFFECT_RAINBOW_MOOD +#define RGBLIGHT_EFFECT_RAINBOW_SWIRL + diff --git a/keyboards/handwired/chiron/keymaps/default/keymap.c b/keyboards/handwired/chiron/keymaps/default/keymap.c new file mode 100644 index 0000000000..53c8edeb0a --- /dev/null +++ b/keyboards/handwired/chiron/keymaps/default/keymap.c @@ -0,0 +1,64 @@ +/* Copyright 2019 Mike Hix + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT( + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_HOME, KC_END, KC_6, KC_7, KC_8, KC_9, KC_0, KC_EQL, + KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_BSPC, KC_DEL, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSLS, + KC_ESC, KC_A, KC_O, LT(1,KC_E), LT(2,KC_U), KC_I, LCTL_T(KC_ENT), RCTL_T(KC_ENT), KC_D, LT(3,KC_H), LT(4,KC_T), KC_N, KC_S, KC_MINS, + KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_PGUP, KC_PGDN, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_RSFT, + KC_CAPS, KC_INS, KC_LCTL, /*, */KC_LALT, LGUI_T(KC_SPC), KC_HYPR, KC_HYPR, RGUI_T(KC_SPC), KC_RALT, /*, */KC_LBRC, KC_RBRC, KC_SLSH + ), + [1] = LAYOUT( + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_WH_U, XXXXXXX, XXXXXXX, RESET, + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_VOLU, KC_WH_L, KC_MS_U, KC_WH_R, XXXXXXX, EEP_RST, + XXXXXXX, XXXXXXX, XXXXXXX, _______, XXXXXXX, XXXXXXX, _______, _______, KC_MUTE, KC_MS_L, KC_MS_D, KC_MS_R, KC_BTN1, KC_BTN2, + _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, KC_VOLD, XXXXXXX, KC_WH_D, XXXXXXX, KC_BTN3, KC_BTN4, + XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX + ), + [2] = LAYOUT( + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_PGUP, XXXXXXX, XXXXXXX, XXXXXXX, + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, KC_INS, KC_PSCR, KC_UP, KC_PAUS, XXXXXXX, XXXXXXX, + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, XXXXXXX, _______, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RGHT, KC_END, XXXXXXX, + _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, KC_PGDN, XXXXXXX, XXXXXXX, _______, + XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX + ), + [3] = LAYOUT( + XXXXXXX, KC_F11, KC_F12, KC_F13, KC_F14, KC_F15, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + XXXXXXX, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + XXXXXXX, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, _______, _______, XXXXXXX, _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, + XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX + ), + [4] = LAYOUT( + RESET, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + EEP_RST, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + XXXXXXX, RGB_HUI, RGB_SAI, RGB_VAI, RGB_MOD, RGB_TOG, _______, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, XXXXXXX, XXXXXXX, + _______, RGB_HUD, RGB_SAD, RGB_VAD, RGB_RMOD, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, + XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX + ) + /* + [] = LAYOUT( + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, + _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, _______, + XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX + ) + */ +}; + diff --git a/keyboards/handwired/chiron/keymaps/default/readme.md b/keyboards/handwired/chiron/keymaps/default/readme.md new file mode 100644 index 0000000000..c95a502f22 --- /dev/null +++ b/keyboards/handwired/chiron/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for chiron diff --git a/keyboards/handwired/dactyl_manuform/4x5/keymaps/default/rules.mk b/keyboards/handwired/chiron/keymaps/default/rules.mk index e69de29bb2..e69de29bb2 100644 --- a/keyboards/handwired/dactyl_manuform/4x5/keymaps/default/rules.mk +++ b/keyboards/handwired/chiron/keymaps/default/rules.mk diff --git a/keyboards/handwired/chiron/readme.md b/keyboards/handwired/chiron/readme.md new file mode 100644 index 0000000000..1e4bcf8b66 --- /dev/null +++ b/keyboards/handwired/chiron/readme.md @@ -0,0 +1,16 @@ +# Chiron Keyboard + + + +This is a custom keyboard meant to be easily and quickly 3D printable on +most FFF/FDM printers. It's inspired by the [Viterbi](https://keeb.io/products/viterbi-keyboard-pcbs-5x7-70-split-ortholinear), [Iris](https://keeb.io/products/iris-keyboard-split-ergonomic-keyboard), and +[Dactyl Manuform](https://github.com/adereth/dactyl-keyboard) keyboards. + +Keyboard Maintainer: [Mike Hix](https://github.com/musl/) +Case: [https://github.com/musl/chiron-keyboard](https://github.com/musl/chiron-keyboard) + +Make example for this keyboard (after setting up your build environment): + + make handwired/chiron:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/chiron/rules.mk b/keyboards/handwired/chiron/rules.mk new file mode 100644 index 0000000000..96f6422700 --- /dev/null +++ b/keyboards/handwired/chiron/rules.mk @@ -0,0 +1,38 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu + +# Build Options +# change yes to no to disable +# +AUDIO_ENABLE = no +AUTOLOG_ENABLE = no +BACKLIGHT_ENABLE = no +BLUETOOTH_ENABLE = no +BOOTMAGIC_ENABLE = no +COMMAND_ENABLE = no +CONSOLE_ENABLE = no +DEBUG_ENABLE = no +EXTRAKEY_ENABLE = no +FAUXCLICKY_ENABLE = no +HD44780_ENABLE = no +LEADER_ENABLE = no +MIDI_ENABLE = no +MOUSEKEY_ENABLE = yes +NKRO_ENABLE = no +RGBLIGHT_ENABLE = yes +SLEEP_LED_ENABLE = yes +TAP_DANCE_ENABLE = no +UCIS_ENABLE = no +UNICODEMAP_ENABLE = no +UNICODE_ENABLE = no +SPLIT_KEYBOARD = yes diff --git a/keyboards/handwired/cmd60/rules.mk b/keyboards/handwired/cmd60/rules.mk index d980716eae..b5e96d74bf 100644 --- a/keyboards/handwired/cmd60/rules.mk +++ b/keyboards/handwired/cmd60/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable @@ -65,5 +28,3 @@ MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 - - diff --git a/keyboards/handwired/co60/rev1/rules.mk b/keyboards/handwired/co60/rev1/rules.mk index 31ce6cbe41..56b5aed0a3 100644 --- a/keyboards/handwired/co60/rev1/rules.mk +++ b/keyboards/handwired/co60/rev1/rules.mk @@ -1,49 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options diff --git a/keyboards/handwired/co60/rev6/rules.mk b/keyboards/handwired/co60/rev6/rules.mk index dba41e12be..fc7cabb108 100644 --- a/keyboards/handwired/co60/rev6/rules.mk +++ b/keyboards/handwired/co60/rev6/rules.mk @@ -1,40 +1,5 @@ -# project specific files - -## chip/board settings -# - the next two should match the directories in -# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -MCU_FAMILY = STM32 -MCU_SERIES = STM32F3xx - -# Linker script to use -# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ -# or <this_dir>/ld/ -MCU_LDSCRIPT = STM32F303xC - -# Startup code to use -# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ -MCU_STARTUP = stm32f3xx - -# Board: it should exist either in <chibios>/os/hal/boards/ -# or <this_dir>/boards -BOARD = GENERIC_STM32_F303XC - -# Cortex version -MCU = cortex-m4 - -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -ARMV = 7 - -USE_FPU = yes - -# Vector table for application -# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ -# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB -# OPT_DEFS = -DCORTEX_VTOR_INIT=0x08005000 - -# Options to pass to dfu-util when flashing -DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave -DFU_SUFFIX_ARGS = -v 0483 -p df11 +# MCU name +MCU = STM32F303 # Code for backlight breathing: SRC += led.c diff --git a/keyboards/handwired/co60/rev7/rules.mk b/keyboards/handwired/co60/rev7/rules.mk index 6e0b3856ab..9daeaf047a 100644 --- a/keyboards/handwired/co60/rev7/rules.mk +++ b/keyboards/handwired/co60/rev7/rules.mk @@ -1,40 +1,5 @@ -# project specific files - -## chip/board settings -# - the next two should match the directories in -# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) -MCU_FAMILY = STM32 -MCU_SERIES = STM32F3xx - -# Linker script to use -# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ -# or <this_dir>/ld/ -MCU_LDSCRIPT = STM32F303xC - -# Startup code to use -# - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ -MCU_STARTUP = stm32f3xx - -# Board: it should exist either in <chibios>/os/hal/boards/ -# or <this_dir>/boards -BOARD = GENERIC_STM32_F303XC - -# Cortex version -MCU = cortex-m4 - -# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 -ARMV = 7 - -USE_FPU = yes - -# Vector table for application -# 0x00000000-0x00001000 area is occupied by bootlaoder.*/ -# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB -# OPT_DEFS = -DCORTEX_VTOR_INIT=0x08005000 - -# Options to pass to dfu-util when flashing -DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave -DFU_SUFFIX_ARGS = -v 0483 -p df11 +# MCU name +MCU = STM32F303 # Code for backlight breathing: SRC += led.c diff --git a/keyboards/handwired/dactyl/keymaps/default/keymap.c b/keyboards/handwired/dactyl/keymaps/default/keymap.c index db666f43fe..47f5ba96ba 100644 --- a/keyboards/handwired/dactyl/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl/keymaps/default/keymap.c @@ -34,8 +34,8 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { */ [BASE] = LAYOUT_dactyl( // layer 0 : default // left hand - KC_EQL, KC_1, KC_2, KC_3, KC_4, KC_5, - KC_DELT, KC_Q, KC_W, KC_E, KC_R, KC_T, + KC_EQL, KC_1, KC_2, KC_3, KC_4, KC_5, + KC_DEL, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_BSPC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_LSFT, CTL_T(KC_Z), KC_X, KC_C, KC_V, KC_B, LT(SYMB,KC_GRV), KC_QUOT, LALT(KC_LSFT), KC_LEFT, KC_RGHT, @@ -137,24 +137,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { ), }; -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - // MACRODOWN only works in this function - switch(id) { - case 0: - if (record->event.pressed) { - SEND_STRING (QMK_KEYBOARD "/" QMK_KEYMAP " @ " QMK_VERSION); - } - break; - case 1: - if (record->event.pressed) { // For resetting EEPROM - eeconfig_init(); - } - break; - } - return MACRO_NONE; -}; - bool process_record_user(uint16_t keycode, keyrecord_t *record) { switch (keycode) { case VRSN: diff --git a/keyboards/handwired/dactyl/keymaps/dvorak/keymap.c b/keyboards/handwired/dactyl/keymaps/dvorak/keymap.c index 7c44f78a65..cc6fc52e5a 100644 --- a/keyboards/handwired/dactyl/keymaps/dvorak/keymap.c +++ b/keyboards/handwired/dactyl/keymaps/dvorak/keymap.c @@ -34,8 +34,8 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { */ [BASE] = LAYOUT_dactyl( // layer 0 : default // left hand - KC_EQL, KC_1, KC_2, KC_3, KC_4, KC_5, - KC_DELT, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, + KC_EQL, KC_1, KC_2, KC_3, KC_4, KC_5, + KC_DEL, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_BSPC, KC_A, KC_O, KC_E, KC_U, KC_I, KC_LSFT, CTL_T(KC_SCLN), KC_Q, KC_J, KC_K, KC_X, LT(SYMB,KC_GRV), KC_EQL, LALT(KC_LSFT), KC_LEFT, KC_RGHT, diff --git a/keyboards/handwired/dactyl/matrix.c b/keyboards/handwired/dactyl/matrix.c index 28cf37522b..faa5c19cf2 100644 --- a/keyboards/handwired/dactyl/matrix.c +++ b/keyboards/handwired/dactyl/matrix.c @@ -76,11 +76,6 @@ uint8_t expander_status; uint8_t expander_input_pin_mask; bool i2c_initialized = false; -#ifdef DEBUG_MATRIX_SCAN_RATE -uint32_t matrix_timer; -uint32_t matrix_scan_count; -#endif - #define ROW_SHIFTER ((matrix_row_t)1) __attribute__ ((weak)) @@ -129,11 +124,6 @@ void matrix_init(void) matrix_debouncing[i] = 0; } -#ifdef DEBUG_MATRIX_SCAN_RATE - matrix_timer = timer_read32(); - matrix_scan_count = 0; -#endif - matrix_init_quantum(); } @@ -236,20 +226,6 @@ uint8_t matrix_scan(void) } } -#ifdef DEBUG_MATRIX_SCAN_RATE - matrix_scan_count++; - - uint32_t timer_now = timer_read32(); - if (TIMER_DIFF_32(timer_now, matrix_timer)>1000) { - print("matrix scan frequency: "); - pdec(matrix_scan_count); - print("\n"); - - matrix_timer = timer_now; - matrix_scan_count = 0; - } -#endif - #if (DIODE_DIRECTION == COL2ROW) for (uint8_t current_row = 0; current_row < MATRIX_ROWS; current_row++) { # if (DEBOUNCE > 0) diff --git a/keyboards/handwired/dactyl/rules.mk b/keyboards/handwired/dactyl/rules.mk index dc25f9c3fb..2e740e3847 100644 --- a/keyboards/handwired/dactyl/rules.mk +++ b/keyboards/handwired/dactyl/rules.mk @@ -1,71 +1,15 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = twimaster.c \ - matrix.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # comment out to disable the options. @@ -84,3 +28,7 @@ SWAP_HANDS_ENABLE = yes # Allow swapping hands of keyboard SLEEP_LED_ENABLE = no API_SYSEX_ENABLE = no RGBLIGHT_ENABLE = no + +# project specific files +SRC = twimaster.c \ + matrix.c diff --git a/keyboards/handwired/dactyl_left/config.h b/keyboards/handwired/dactyl_left/config.h new file mode 100644 index 0000000000..43c0d3d43f --- /dev/null +++ b/keyboards/handwired/dactyl_left/config.h @@ -0,0 +1,251 @@ +/* +Copyright 2019 RedForty + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER RedForty +#define PRODUCT dactyl_left +#define DESCRIPTION A custom keyboard + +/* key matrix size */ +#define MATRIX_ROWS 6 +#define MATRIX_COLS 6 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS \ + { F0, F1, F4, F5, F6, F7 } +#define MATRIX_COL_PINS \ + { D0, B7, B3, B2, B1, B0 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +/* + * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN. + */ +#define SOFT_SERIAL_PIN D2 // or D1, D2, D3, E6 + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + +// #define RGB_DI_PIN E2 +// #ifdef RGB_DI_PIN +// #define RGBLED_NUM 16 +// #define RGBLIGHT_HUE_STEP 8 +// #define RGBLIGHT_SAT_STEP 8 +// #define RGBLIGHT_VAL_STEP 8 +// #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ +// #define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ +// /*== all animations enable ==*/ +// #define RGBLIGHT_ANIMATIONS +// /*== or choose animations ==*/ +// #define RGBLIGHT_EFFECT_BREATHING +// #define RGBLIGHT_EFFECT_RAINBOW_MOOD +// #define RGBLIGHT_EFFECT_RAINBOW_SWIRL +// #define RGBLIGHT_EFFECT_SNAKE +// #define RGBLIGHT_EFFECT_KNIGHT +// #define RGBLIGHT_EFFECT_CHRISTMAS +// #define RGBLIGHT_EFFECT_STATIC_GRADIENT +// #define RGBLIGHT_EFFECT_RGB_TEST +// #define RGBLIGHT_EFFECT_ALTERNATING +// /*== customize breathing effect ==*/ +// /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ +// #define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 +// /*==== use exp() and sin() ====*/ +// #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 +// #define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 +// #endif + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +/* defined by default; to change, uncomment and set to the combination you want */ +// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP H +//#define MAGIC_KEY_HELP_ALT SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER0_ALT GRAVE +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER B +//#define MAGIC_KEY_BOOTLOADER_ALT ESC +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_EEPROM_CLEAR BSPACE +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +/* + * HD44780 LCD Display Configuration + */ +/* +#define LCD_LINES 2 //< number of visible lines of the display +#define LCD_DISP_LENGTH 16 //< visibles characters per line of the display + +#define LCD_IO_MODE 1 //< 0: memory mapped mode, 1: IO port mode + +#if LCD_IO_MODE +#define LCD_PORT PORTB //< port for the LCD lines +#define LCD_DATA0_PORT LCD_PORT //< port for 4bit data bit 0 +#define LCD_DATA1_PORT LCD_PORT //< port for 4bit data bit 1 +#define LCD_DATA2_PORT LCD_PORT //< port for 4bit data bit 2 +#define LCD_DATA3_PORT LCD_PORT //< port for 4bit data bit 3 +#define LCD_DATA0_PIN 4 //< pin for 4bit data bit 0 +#define LCD_DATA1_PIN 5 //< pin for 4bit data bit 1 +#define LCD_DATA2_PIN 6 //< pin for 4bit data bit 2 +#define LCD_DATA3_PIN 7 //< pin for 4bit data bit 3 +#define LCD_RS_PORT LCD_PORT //< port for RS line +#define LCD_RS_PIN 3 //< pin for RS line +#define LCD_RW_PORT LCD_PORT //< port for RW line +#define LCD_RW_PIN 2 //< pin for RW line +#define LCD_E_PORT LCD_PORT //< port for Enable line +#define LCD_E_PIN 1 //< pin for Enable line +#endif +*/ + +/* Bootmagic Lite key configuration */ +// #define BOOTMAGIC_LITE_ROW 0 +// #define BOOTMAGIC_LITE_COLUMN 0 diff --git a/keyboards/handwired/dactyl_left/dactyl_left.c b/keyboards/handwired/dactyl_left/dactyl_left.c new file mode 100644 index 0000000000..e6fe3402da --- /dev/null +++ b/keyboards/handwired/dactyl_left/dactyl_left.c @@ -0,0 +1,51 @@ +/* Copyright 2019 RedForty + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "dactyl_left.h" + +// Optional override functions below. +// You can leave any or all of these undefined. +// These are only required if you want to perform custom actions. + +/* + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} + +*/ diff --git a/keyboards/handwired/dactyl_left/dactyl_left.h b/keyboards/handwired/dactyl_left/dactyl_left.h new file mode 100644 index 0000000000..1babf3fe47 --- /dev/null +++ b/keyboards/handwired/dactyl_left/dactyl_left.h @@ -0,0 +1,42 @@ +/* Copyright 2019 RedForty + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT(\ + k00, k01, k02, k03, k04, k05, \ + k10, k11, k12, k13, k14, k15, \ + k20, k21, k22, k23, k24, k25, \ + k30, k31, k32, k33, k34, k35, \ + k40, k41, k42, k43, k44, \ + k50, k51, k52, k53, k54, k55 \ +) { \ + { k00, k01, k02, k03, k04, k05 }, \ + { k10, k11, k12, k13, k14, k15 }, \ + { k20, k21, k22, k23, k24, k25 }, \ + { k30, k31, k32, k33, k34, k35 }, \ + { k40, k41, k42, k43, k44, KC_NO }, \ + { k50, k51, k52, k53, k54, k55 } \ +} diff --git a/keyboards/handwired/dactyl_left/info.json b/keyboards/handwired/dactyl_left/info.json new file mode 100644 index 0000000000..4c9cd0845b --- /dev/null +++ b/keyboards/handwired/dactyl_left/info.json @@ -0,0 +1,12 @@ +{ + "keyboard_name": "dactyl_left", + "url": "", + "maintainer": "RedForty", + "width": 8, + "height": 7.75, + "layouts": { + "LAYOUT": { + "layout": [{"x":0, "y":0.375, "w":1.5}, {"x":1.5, "y":0.375}, {"x":2.5, "y":0.125}, {"x":3.5, "y":0}, {"x":4.5, "y":0.125}, {"x":5.5, "y":0.25}, {"x":0, "y":1.375, "w":1.5}, {"x":1.5, "y":1.375}, {"x":2.5, "y":1.125}, {"x":3.5, "y":1}, {"x":4.5, "y":1.125}, {"x":5.5, "y":1.25}, {"x":0, "y":2.375, "w":1.5}, {"x":1.5, "y":2.375}, {"x":2.5, "y":2.125}, {"x":3.5, "y":2}, {"x":4.5, "y":2.125}, {"x":5.5, "y":2.25}, {"x":0, "y":3.375, "w":1.5}, {"x":1.5, "y":3.375}, {"x":2.5, "y":3.125}, {"x":3.5, "y":3}, {"x":4.5, "y":3.125}, {"x":5.5, "y":3.25}, {"x":0.5, "y":4.375}, {"x":1.5, "y":4.375}, {"x":2.5, "y":4.125}, {"x":3.5, "y":4}, {"x":4.5, "y":4.125}, {"x":6, "y":4.75}, {"x":7, "y":4.75}, {"x":5, "y":5.75, "h":2}, {"x":6, "y":5.75, "h":2}, {"x":7, "y":5.75}, {"x":7, "y":6.75}] + } + } +} diff --git a/keyboards/handwired/dactyl_left/keymaps/default/config.h b/keyboards/handwired/dactyl_left/keymaps/default/config.h new file mode 100644 index 0000000000..729cab1684 --- /dev/null +++ b/keyboards/handwired/dactyl_left/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 RedForty + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/dactyl_left/keymaps/default/keymap.c b/keyboards/handwired/dactyl_left/keymaps/default/keymap.c new file mode 100644 index 0000000000..708a380890 --- /dev/null +++ b/keyboards/handwired/dactyl_left/keymaps/default/keymap.c @@ -0,0 +1,57 @@ +/* Copyright 2019 RedForty + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +// Defines the keycodes used by our macros in process_record_user +enum custom_keycodes { QMKBEST = SAFE_RANGE, QMKURL }; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT(/* Base */ + KC_SPC, KC_1, KC_2, KC_3, KC_4, KC_5, + KC_SPC, KC_Q, KC_W, KC_E, KC_R, KC_T, + KC_SPC, KC_A, KC_S, KC_D, KC_F, KC_G, + KC_SPC, KC_Z, KC_X, KC_C, KC_V, KC_B, + KC_SPC, KC_SPC, KC_SPC, KC_SPC, KC_SPC, + KC_SPC, KC_SPC, KC_SPC, KC_SPC, KC_SPC, KC_SPC), +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QMKBEST: + if (record->event.pressed) { + // when keycode QMKBEST is pressed + SEND_STRING("QMK is the best thing ever!"); + } else { + // when keycode QMKBEST is released + } + break; + case QMKURL: + if (record->event.pressed) { + // when keycode QMKURL is pressed + SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER)); + } else { + // when keycode QMKURL is released + } + break; + } + return true; +} + +void matrix_init_user(void) {} + +void matrix_scan_user(void) {} + +void led_set_user(uint8_t usb_led) {} diff --git a/keyboards/handwired/dactyl_left/keymaps/default/readme.md b/keyboards/handwired/dactyl_left/keymaps/default/readme.md new file mode 100644 index 0000000000..7fa3e26f5f --- /dev/null +++ b/keyboards/handwired/dactyl_left/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for dactyl_left
\ No newline at end of file diff --git a/keyboards/handwired/dactyl_left/readme.md b/keyboards/handwired/dactyl_left/readme.md new file mode 100644 index 0000000000..edcc832068 --- /dev/null +++ b/keyboards/handwired/dactyl_left/readme.md @@ -0,0 +1,15 @@ +# dactyl_left + + + +A custom build of an ergodox dactyl using a Teensy. Pins are custom. + +Keyboard Maintainer: [RedForty](https://github.com/RedForty) +Hardware Supported: Left side of the dactyl only +Hardware Availability: Custom job + +Make example for this keyboard (after setting up your build environment): + + make handwired/dactyl_left:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/dactyl_left/rules.mk b/keyboards/handwired/dactyl_left/rules.mk new file mode 100644 index 0000000000..61c123d038 --- /dev/null +++ b/keyboards/handwired/dactyl_left/rules.mk @@ -0,0 +1,34 @@ +# MCU name +MCU = atmega32u4 + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = halfkay + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) diff --git a/keyboards/handwired/dactyl_manuform/4x5/4x5.h b/keyboards/handwired/dactyl_manuform/4x5/4x5.h index b34d97adbf..a70f52f3e1 100644 --- a/keyboards/handwired/dactyl_manuform/4x5/4x5.h +++ b/keyboards/handwired/dactyl_manuform/4x5/4x5.h @@ -2,10 +2,8 @@ #include "dactyl_manuform.h" -//void promicro_bootloader_jmp(bool program); #include "quantum.h" - #ifdef USE_I2C #include <stddef.h> #ifdef __AVR__ @@ -14,8 +12,6 @@ #endif #endif -//void promicro_bootloader_jmp(bool program); - #ifndef FLIP_HALF #define LAYOUT( \ L00, L01, L02, L03, L04, R00, R01, R02, R03, R04, \ diff --git a/keyboards/handwired/dactyl_manuform/4x5/keymaps/default/keymap.c b/keyboards/handwired/dactyl_manuform/4x5/keymaps/default/keymap.c index 2e5cfd7ced..1a328f9d0a 100644 --- a/keyboards/handwired/dactyl_manuform/4x5/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl_manuform/4x5/keymaps/default/keymap.c @@ -1,6 +1,5 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; #define _BASE 0 #define _RAISE 1 @@ -20,7 +19,7 @@ extern keymap_config_t keymap_config; #define KC_MU KC_MS_UP #define KC_MD KC_MS_DOWN #define KC_MB1 KC_MS_BTN1 -#define KC_MB2 KC_MS_BTN1 +#define KC_MB2 KC_MS_BTN2 #define RAISE MO(_RAISE) #define LOWER MO(_LOWER) @@ -44,7 +43,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * '------+------' '------+------' * | TAB | HOME | | END | DEL | * '------+------' '------+------' - * | Lower| ~ | | GUI | Raise| + * | Raise| ~ | | GUI | Lower| * '------+------' '------+------' */ @@ -92,7 +91,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * ,----------------------------------, ,----------------------------------, * | F1 | F2 | F3 | F4 | F5 | | F6 | F7 | F8 | F9 | F10 | * |------+------+------+------+------| |-------------+------+------+------| - * | 1 | 2 | 3 | 4 | 5 | | 6 | 7 | 8 | 9 | 10 | + * | 1 | 2 | 3 | 4 | 5 | | 6 | 7 | 8 | 9 | 0 | * |------+------+------+------+------| |------|------+------+------+------| * | ! | @ | # | $ | % | | ^ | & | * | ( | ) | * |------+------+------+-------------, ,-------------+------+------+------, diff --git a/keyboards/handwired/dactyl_manuform/4x5/keymaps/dvorak/rules.mk b/keyboards/handwired/dactyl_manuform/4x5/keymaps/dvorak/rules.mk deleted file mode 100644 index e69de29bb2..0000000000 --- a/keyboards/handwired/dactyl_manuform/4x5/keymaps/dvorak/rules.mk +++ /dev/null diff --git a/keyboards/handwired/dactyl_manuform/4x6/keymaps/default/keymap.c b/keyboards/handwired/dactyl_manuform/4x6/keymaps/default/keymap.c index ad23beef5c..52ddfad038 100644 --- a/keyboards/handwired/dactyl_manuform/4x6/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl_manuform/4x6/keymaps/default/keymap.c @@ -1,6 +1,5 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; #define _BASE 0 #define _RAISE 1 @@ -84,4 +83,3 @@ void persistent_default_layer_set(uint16_t default_layer) { eeconfig_update_default_layer(default_layer); default_layer_set(default_layer); } - diff --git a/keyboards/handwired/dactyl_manuform/5x6/keymaps/default/keymap.c b/keyboards/handwired/dactyl_manuform/5x6/keymaps/default/keymap.c index 0d1efde33b..0910faf899 100644 --- a/keyboards/handwired/dactyl_manuform/5x6/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl_manuform/5x6/keymaps/default/keymap.c @@ -2,7 +2,6 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; #define _QWERTY 0 #define _LOWER 1 @@ -48,5 +47,3 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { _______,_______, _______,_______ ), }; - - diff --git a/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/config.h b/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/config.h new file mode 100644 index 0000000000..98dc760031 --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/config.h @@ -0,0 +1,41 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + + +#pragma once + + +// #define USE_SERIAL +#define USE_I2C +// #define MASTER_LEFT +// #define MASTER_RIGHT +#define EE_HANDS +// Rows are doubled-up +// #define DEBOUNCE 5 +#define TAPPING_TOGGLE 3 +#define ONESHOT_TAP_TOGGLE 3 +#define PERMISSIVE_HOLD +#define IGNORE_MOD_TAP_INTERRUPT +#define TAPPING_TERM 300 +#ifdef RGBLED_NUM +# undef RGBLED_NUM +#endif +#define RGBLED_NUM 54 +#define RGBLIGHT_LIMIT_VAL 200 +#define RGBLIGHT_ANIMATIONS +// #define RGBLIGHT_LED_MAP { 11,10,9,8,7,6,5,4,3,2,1,0,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26 } +#define RGBLIGHT_SPLIT 27 diff --git a/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/keymap.c b/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/keymap.c new file mode 100644 index 0000000000..71a91cfd2a --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/keymap.c @@ -0,0 +1,61 @@ +/* A standard layout for the Dactyl Manuform 5x6 Keyboard */ + +#include QMK_KEYBOARD_H +#include "rishka.h" + +enum layers { + BASE, // default layer + WIN, // Switch keys that are needed in windows + SYMB, // symbols + MDIA // media keys +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + [BASE] = LAYOUT_5x6_wrapper( + KC_EQL , ________________NUMBERS_L__________________, ________________NUMBERS_R__________________, KC_MINS, + KC_ESC , _________________QWERTY_L1_________________, _________________QWERTY_R1_________________, KC_BSLS, + KC_F1 , _____________MOD_QWERTY_L2_________________, _____________MOD_QWERTY_R2_________________, KC_QUOT, + OS_LSFT, _________________QWERTY_L3_________________, _________________QWERTY_R3_________________, OS_RSFT, + KC_LEFT,KC_RGHT, KC_UP, KC_DOWN, + KC_BSPC, KC_SPC, KC_TAB, KC_ENT, + KC_LGUI, MO(SYMB), MO(SYMB), TT(MDIA), + KC_DEL, KC_GRV, TT(WIN), KC_LALT + ), + [WIN] = LAYOUT_5x6_wrapper( + + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _________________QWERTY_L2_________________, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, + _______, _______, _______, _______, + KC_LCTL, _______, _______, _______, + _______, _______, _______, _______ + ), + + [SYMB] = LAYOUT_5x6_wrapper( + KC_F12 , ______________________F_L__________________, ______________________F_R__________________, KC_F11, + _______, _________________SYMBOL_L1_________________, _________________SYMBOL_R1_________________, KC_NLCK, + _______, _________________SYMBOL_L2_________________, _________________SYMBOL_R2_________________, _______, + _______, _________________SYMBOL_L3_________________, _________________SYMBOL_R3_________________, _______, + _______, _______, KC_P0 , KC_PDOT, + _______, _______, _______, _______, + RESET , _______, _______, _______, + RGB_TOG, _______, _______, _______ + ), + [MDIA] = LAYOUT_5x6_wrapper( + + RGB_MOD, RGB_HUI, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + RGB_M_SN, RGB_HUD, _______, KC_MS_U, _______, KC_WH_U, _______, _______, KC_WH_U, _______, _______, _______, + RGB_VAI, RGB_SAI, KC_MS_L, KC_MS_D, KC_MS_R, KC_WH_D, _______, MOUSE_L, KC_WH_D, MOUSE_R, _______, _______, + RGB_VAD, RGB_SAD, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, + KC_BTN1, KC_BTN2, _______, _______, + KC_BTN3, KC_BTN4, _______, _______, + KC_BTN5, _______, _______, _______ + + ), +}; + + diff --git a/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/rules.mk b/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/rules.mk new file mode 100644 index 0000000000..7084862d13 --- /dev/null +++ b/keyboards/handwired/dactyl_manuform/5x6/keymaps/rishka/rules.mk @@ -0,0 +1,3 @@ +BOOTLOADER=qmk-dfu +RGBLIGHT_ENABLE = yes + diff --git a/keyboards/handwired/dactyl_manuform/5x7/keymaps/default/keymap.c b/keyboards/handwired/dactyl_manuform/5x7/keymaps/default/keymap.c index 1378f87232..eb4deb6285 100644 --- a/keyboards/handwired/dactyl_manuform/5x7/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl_manuform/5x7/keymaps/default/keymap.c @@ -1,6 +1,5 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. diff --git a/keyboards/handwired/dactyl_manuform/6x6/keymaps/default/keymap.c b/keyboards/handwired/dactyl_manuform/6x6/keymaps/default/keymap.c index b78a560086..fd2e5f413d 100644 --- a/keyboards/handwired/dactyl_manuform/6x6/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl_manuform/6x6/keymaps/default/keymap.c @@ -1,6 +1,5 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; #define _QWERTY 0 #define _LOWER 1 @@ -52,4 +51,3 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { ), }; - diff --git a/keyboards/handwired/dactyl_manuform/dactyl_manuform.h b/keyboards/handwired/dactyl_manuform/dactyl_manuform.h index 72f2acaab4..d8f27f729c 100644 --- a/keyboards/handwired/dactyl_manuform/dactyl_manuform.h +++ b/keyboards/handwired/dactyl_manuform/dactyl_manuform.h @@ -14,7 +14,6 @@ #include "62key.h" #endif -//void promicro_bootloader_jmp(bool program); #include "quantum.h" diff --git a/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/keymap.c b/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/keymap.c index 3012d40a1b..3770a6d68e 100644 --- a/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl_manuform/dmote/62key/keymaps/default/keymap.c @@ -3,7 +3,6 @@ #include <keymap_colemak.h> #include <sendstring_colemak.h> -extern keymap_config_t keymap_config; // Automatic Layer ID: enum layer_names { diff --git a/keyboards/handwired/dactyl_manuform/rules.mk b/keyboards/handwired/dactyl_manuform/rules.mk index a93de36858..1ba5f5a093 100644 --- a/keyboards/handwired/dactyl_manuform/rules.mk +++ b/keyboards/handwired/dactyl_manuform/rules.mk @@ -1,48 +1,16 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/handwired/dactyl_promicro/keymaps/default/keymap.c b/keyboards/handwired/dactyl_promicro/keymaps/default/keymap.c index d396e46762..394803aef5 100644 --- a/keyboards/handwired/dactyl_promicro/keymaps/default/keymap.c +++ b/keyboards/handwired/dactyl_promicro/keymaps/default/keymap.c @@ -3,7 +3,6 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; #define _QWERTY 0 #define _LOWER 1 diff --git a/keyboards/handwired/dactyl_promicro/rules.mk b/keyboards/handwired/dactyl_promicro/rules.mk index a93de36858..1ba5f5a093 100644 --- a/keyboards/handwired/dactyl_promicro/rules.mk +++ b/keyboards/handwired/dactyl_promicro/rules.mk @@ -1,48 +1,16 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/handwired/daishi/config.h b/keyboards/handwired/daishi/config.h index 15ff6a6a62..b4665bece4 100644 --- a/keyboards/handwired/daishi/config.h +++ b/keyboards/handwired/daishi/config.h @@ -52,10 +52,9 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define DEBOUNCE 5 /* Set up rotary encoder */ -#define NUMBER_OF_ENCODERS 1 #define ENCODERS_PAD_A { F1 } #define ENCODERS_PAD_B { F0 } #define ENCODER_RESOLUTION 2 /* Set delay for tap_code on rotary encoder */ -#define TAP_CODE_DELAY 10
\ No newline at end of file +#define TAP_CODE_DELAY 10 diff --git a/keyboards/handwired/daishi/rules.mk b/keyboards/handwired/daishi/rules.mk index ece1eaaac3..dacecfb0b1 100644 --- a/keyboards/handwired/daishi/rules.mk +++ b/keyboards/handwired/daishi/rules.mk @@ -1,49 +1,14 @@ # MCU name MCU = at90usb1286 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # QMK Build Options @@ -63,4 +28,4 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -ENCODER_ENABLE = yes # Add rotary encoder support
\ No newline at end of file +ENCODER_ENABLE = yes # Add rotary encoder support diff --git a/keyboards/handwired/datahand/rules.mk b/keyboards/handwired/datahand/rules.mk index 59f14e17a4..a46dcedb1c 100644 --- a/keyboards/handwired/datahand/rules.mk +++ b/keyboards/handwired/datahand/rules.mk @@ -1,44 +1,14 @@ -# Project-specific includes -SRC = matrix.c - # MCU name MCU = at90usb1286 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay # Build Options @@ -57,3 +27,6 @@ CUSTOM_MATRIX = yes # We definitely have a nonstandard matrix # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +# Project specific files +SRC = matrix.c diff --git a/keyboards/handwired/downbubble/rules.mk b/keyboards/handwired/downbubble/rules.mk index 87d0d4a1e2..189b82720e 100644 --- a/keyboards/handwired/downbubble/rules.mk +++ b/keyboards/handwired/downbubble/rules.mk @@ -1,43 +1,5 @@ # MCU name MCU = at90usb1286 -#MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay @@ -45,20 +7,10 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/handwired/fivethirteen/rules.mk b/keyboards/handwired/fivethirteen/rules.mk index c8dd19ef7b..64d566cb17 100644 --- a/keyboards/handwired/fivethirteen/rules.mk +++ b/keyboards/handwired/fivethirteen/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable diff --git a/keyboards/handwired/frenchdev/keymaps/default/keymap.c b/keyboards/handwired/frenchdev/keymaps/default/keymap.c index 7b82f36e36..b0713b730c 100644 --- a/keyboards/handwired/frenchdev/keymaps/default/keymap.c +++ b/keyboards/handwired/frenchdev/keymaps/default/keymap.c @@ -12,8 +12,8 @@ #define PEDAL_DELAY 250 #define KEY_DELAY 130 -enum macros { - M_LP = SAFE_RANGE, // left pedal +enum custom_keycodes { + M_LP = SAFE_RANGE, // left pedal M_RP, // right pedal M_SF, // shift M_SFS, // shift and space diff --git a/keyboards/handwired/frenchdev/matrix.c b/keyboards/handwired/frenchdev/matrix.c index 26c2b31260..c9c7e94aea 100644 --- a/keyboards/handwired/frenchdev/matrix.c +++ b/keyboards/handwired/frenchdev/matrix.c @@ -35,9 +35,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "frenchdev.h" -#ifdef DEBUG_MATRIX_SCAN_RATE -#include "timer.h" -#endif /* * This constant define not debouncing time in msecs, but amount of matrix @@ -66,12 +63,6 @@ static void select_row(uint8_t row); static uint8_t mcp23018_reset_loop; -#ifdef DEBUG_MATRIX_SCAN_RATE -uint32_t matrix_timer; -uint32_t matrix_scan_count; -#endif - - __attribute__ ((weak)) void matrix_init_user(void) {} @@ -120,13 +111,7 @@ void matrix_init(void) matrix_debouncing[i] = 0; } -#ifdef DEBUG_MATRIX_SCAN_RATE - matrix_timer = timer_read32(); - matrix_scan_count = 0; -#endif - matrix_init_quantum(); - } void matrix_power_up(void) { @@ -140,12 +125,6 @@ void matrix_power_up(void) { matrix[i] = 0; matrix_debouncing[i] = 0; } - -#ifdef DEBUG_MATRIX_SCAN_RATE - matrix_timer = timer_read32(); - matrix_scan_count = 0; -#endif - } uint8_t matrix_scan(void) @@ -165,20 +144,6 @@ uint8_t matrix_scan(void) } } -#ifdef DEBUG_MATRIX_SCAN_RATE - matrix_scan_count++; - - uint32_t timer_now = timer_read32(); - if (TIMER_DIFF_32(timer_now, matrix_timer)>1000) { - print("matrix scan frequency: "); - pdec(matrix_scan_count); - print("\n"); - - matrix_timer = timer_now; - matrix_scan_count = 0; - } -#endif - for (uint8_t i = 0; i < MATRIX_ROWS; i++) { select_row(i); wait_us(30); // without this wait read unstable value. diff --git a/keyboards/handwired/frenchdev/rules.mk b/keyboards/handwired/frenchdev/rules.mk index 69a12b68d7..abf4e62c4b 100644 --- a/keyboards/handwired/frenchdev/rules.mk +++ b/keyboards/handwired/frenchdev/rules.mk @@ -1,70 +1,15 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = i2c_master.c \ - matrix.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -BOOTLOADER = halfKay +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # comment out to disable the options. @@ -85,3 +30,7 @@ BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 RGBLIGHT_ENABLE = no API_SYSEX_ENABLE = no + +# project specific files +SRC = i2c_master.c \ + matrix.c diff --git a/keyboards/handwired/fruity60/config.h b/keyboards/handwired/fruity60/config.h new file mode 100644 index 0000000000..5cccba3dc8 --- /dev/null +++ b/keyboards/handwired/fruity60/config.h @@ -0,0 +1,53 @@ +/* +Copyright 2019 Yan-Fa Li + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0xB170 +#define DEVICE_VER 0x0001 +#define MANUFACTURER yanfali +#define PRODUCT fruity60 +#define DESCRIPTION An Adafruit BLE 32u4 capable 60 + +/* key matrix size */ +#define MATRIX_ROWS 6 +#define MATRIX_COLS 11 + +#define MATRIX_ROW_PINS \ + { B6, B5, D7, C6, D0, D1 } +#define MATRIX_COL_PINS \ + { F7, F6, F5, F4, F1, F0, D2, D3, B7, D6, C7 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE diff --git a/keyboards/handwired/fruity60/fruity60.c b/keyboards/handwired/fruity60/fruity60.c new file mode 100644 index 0000000000..d68b17955e --- /dev/null +++ b/keyboards/handwired/fruity60/fruity60.c @@ -0,0 +1,51 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "fruity60.h" + +// Optional override functions below. +// You can leave any or all of these undefined. +// These are only required if you want to perform custom actions. + +/* + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} + +*/ diff --git a/keyboards/handwired/fruity60/fruity60.h b/keyboards/handwired/fruity60/fruity60.h new file mode 100644 index 0000000000..7eb2e7e6fd --- /dev/null +++ b/keyboards/handwired/fruity60/fruity60.h @@ -0,0 +1,42 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT_60_tsangan_hhkb( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k50, k51, k52, k53, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k54, k55, k56, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k57, k58, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k59, k5a, \ + k40, k41, k42, k45, k48, k49, k4a \ + ) \ + { \ + {k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a}, \ + {k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a}, \ + {k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a}, \ + {k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a}, \ + {k40, k41, k42, KC_NO, KC_NO, k45, KC_NO, KC_NO, k48, k49, k4a}, \ + {k50, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5a}, \ + } diff --git a/keyboards/handwired/fruity60/info.json b/keyboards/handwired/fruity60/info.json new file mode 100644 index 0000000000..7cf5e61d18 --- /dev/null +++ b/keyboards/handwired/fruity60/info.json @@ -0,0 +1,12 @@ +{ + "keyboard_name": "fruity60", + "url": "https://github.com/yanfali/fruity60", + "maintainer": "qmk", + "width": 15, + "height": 5, + "layouts": { + "LAYOUT": { + "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"x":13, "y":0}, {"label":"Backspace", "x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.5}, {"label":"Win", "x":1.5, "y":4}, {"label":"Alt", "x":2.5, "y":4, "w":1.5}, {"x":4, "y":4, "w":7}, {"label":"Alt", "x":11, "y":4, "w":1.5}, {"label":"Win", "x":12.5, "y":4}, {"label":"Menu", "x":13.5, "y":4, "w":1.5}] + } + } +} diff --git a/keyboards/handwired/fruity60/keymaps/default/config.h b/keyboards/handwired/fruity60/keymaps/default/config.h new file mode 100644 index 0000000000..7d7844ac61 --- /dev/null +++ b/keyboards/handwired/fruity60/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/fruity60/keymaps/default/keymap.c b/keyboards/handwired/fruity60/keymaps/default/keymap.c new file mode 100644 index 0000000000..a6cd15f4e2 --- /dev/null +++ b/keyboards/handwired/fruity60/keymaps/default/keymap.c @@ -0,0 +1,25 @@ +#include QMK_KEYBOARD_H + +enum layer { + BASE, + FN, +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [BASE] = LAYOUT_60_tsangan_hhkb( + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_GRV, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + LCTL_T(KC_ESC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(FN), + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT, KC_RCTL + ), + + [FN] = LAYOUT_60_tsangan_hhkb( + _______, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, + _______, _______, KC_UP, _______, _______, _______, _______, _______, _______, _______, _______, _______, EEP_RST, RESET, + KC_CAPS, KC_LEFT, KC_DOWN, KC_RGHT, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______ + ), + +}; diff --git a/keyboards/handwired/fruity60/keymaps/default/readme.md b/keyboards/handwired/fruity60/keymaps/default/readme.md new file mode 100644 index 0000000000..7c01154cd1 --- /dev/null +++ b/keyboards/handwired/fruity60/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for fruity60 diff --git a/keyboards/handwired/fruity60/readme.md b/keyboards/handwired/fruity60/readme.md new file mode 100644 index 0000000000..ed476d2643 --- /dev/null +++ b/keyboards/handwired/fruity60/readme.md @@ -0,0 +1,15 @@ +# fruity60 + + + +A 60% tsangan, split bs/rs keyboard designed to support the bluefruit 32u4 ble controller + +Keyboard Maintainer: [Yan-Fa Li](https://github.com/yanfali)<br> +Hardware Supported: [github](https://github.com/yanfali/fruity60)<br> +Hardware Availability: You can make them yourself by downloading kicad and generating gerbers.<br> + +Make example for this keyboard (after setting up your build environment): + + make fruity60:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/fruity60/rules.mk b/keyboards/handwired/fruity60/rules.mk new file mode 100644 index 0000000000..9e64f161af --- /dev/null +++ b/keyboards/handwired/fruity60/rules.mk @@ -0,0 +1,38 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency +F_CPU = 8000000 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +BLUETOOTH = AdafruitBLE + +LAYOUTS = 60_tsangan_hhkb diff --git a/keyboards/handwired/gamenum/keymaps/default/keymap.c b/keyboards/handwired/gamenum/keymaps/default/keymap.c index 7d667cd390..237b0fb927 100644 --- a/keyboards/handwired/gamenum/keymaps/default/keymap.c +++ b/keyboards/handwired/gamenum/keymaps/default/keymap.c @@ -29,11 +29,6 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { ) }; -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) { - return MACRO_NONE; -}; - - bool process_record_user(uint16_t keycode, keyrecord_t *record) { switch(keycode) { case TO(HDN): diff --git a/keyboards/handwired/gamenum/rules.mk b/keyboards/handwired/gamenum/rules.mk index d980716eae..3989329835 100644 --- a/keyboards/handwired/gamenum/rules.mk +++ b/keyboards/handwired/gamenum/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change yes to no to disable @@ -65,5 +28,3 @@ MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 - - diff --git a/keyboards/handwired/hacked_motospeed/config.h b/keyboards/handwired/hacked_motospeed/config.h index 1a341c0f4e..d4bf11f235 100644 --- a/keyboards/handwired/hacked_motospeed/config.h +++ b/keyboards/handwired/hacked_motospeed/config.h @@ -43,7 +43,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. */ // WR XR YR ZR VR ZL YL XL WL VL -#define MATRIX_ROW_PINS { B3, B5, F1, B4, B6, D5, D4, D6, D7, C4} +#define MATRIX_ROW_PINS { B3, B4, F1, B5, B6, D5, D4, D6, D7, C4} // ER DR CR BR AR FR FL AL BL CL DL EL #define MATRIX_COL_PINS { F7, F6, F5, F4, F3, F2, E0, E1, C0, C1, C2, C3 } @@ -120,7 +120,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. * power-up. * */ -#define FORCE_NKRO /* * Magic Key Options diff --git a/keyboards/handwired/hacked_motospeed/keymaps/german/keymap.c b/keyboards/handwired/hacked_motospeed/keymaps/german/keymap.c new file mode 100644 index 0000000000..23c076680f --- /dev/null +++ b/keyboards/handwired/hacked_motospeed/keymaps/german/keymap.c @@ -0,0 +1,10 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[0] = LAYOUT(KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, LSFT(KC_8), LSFT(KC_9), KC_PEQL, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, LSFT(KC_MINS), MO(2), MO(6), KC_TAB, KC_BSPC, KC_SPC, MO(1), KC_LCTL, KC_LALT, MO(4), KC_LGUI, MO(2)), +[1] = LAYOUT(LALT(KC_F4), LSFT(KC_Q), LSFT(KC_W), LSFT(KC_E), LSFT(KC_R), LSFT(KC_T), LSFT(KC_Y), LSFT(KC_U), LSFT(KC_I), LSFT(KC_O), LSFT(KC_P), LSFT(KC_A), LSFT(KC_S), LSFT(KC_D), LSFT(KC_F), LSFT(KC_G), LSFT(KC_H), LSFT(KC_J), LSFT(KC_K), LSFT(KC_L), RALT(KC_7), RALT(KC_0), KC_NUHS, LSFT(KC_Z), LSFT(KC_X), LSFT(KC_C), LSFT(KC_V), LSFT(KC_B), LSFT(KC_N), LSFT(KC_M), LSFT(KC_COMM), LSFT(KC_DOT), LSFT(KC_1), MO(3), TG(6), LSFT(KC_TAB), KC_DEL, KC_ENT, KC_TRNS, LSFT(KC_LCTL), LSFT(KC_LALT), LSFT(KC_RALT), LSFT(KC_LGUI), MO(3)), +[2] = LAYOUT(LSFT(KC_GRV), RALT(KC_Q), KC_JYEN, RALT(KC_E), LSFT(KC_4), LSFT(KC_5), LSFT(KC_6), KC_LBRC, KC_UP, KC_SCLN, KC_PSCR, KC_QUOT, KC_MINS, LSFT(KC_7), LSFT(KC_2), LSFT(KC_NUHS), LSFT(KC_3), KC_LEFT, KC_DOWN, KC_RGHT, KC_NUBS, LSFT(KC_NUBS), RALT(KC_RBRC), KC_GRV, LSFT(KC_RBRC), KC_SLSH, KC_RBRC, RALT(KC_NUBS), KC_HOME, KC_PGDN, KC_PGUP, KC_END, RALT(KC_6), KC_TRNS, KC_CAPS, KC_TAB, KC_DEL, KC_ENT, MO(3), OUT_BT, OUT_USB, OUT_AUTO, BL_STEP, KC_TRNS), +[3] = LAYOUT(LSFT(KC_GRV), RALT(KC_Q), KC_JYEN, RALT(KC_E), LSFT(KC_4), LSFT(KC_5), LSFT(KC_6), LSFT(KC_LBRC), KC_UP, LSFT(KC_SCLN), KC_PSCR, LSFT(KC_QUOT), KC_MINS, RALT(KC_MINS), LSFT(KC_EQL), KC_EQL, LSFT(KC_3), KC_LEFT, KC_DOWN, KC_RGHT, RALT(KC_8), RALT(KC_9), RALT(KC_RBRC), KC_GRV, LSFT(KC_RBRC), LSFT(KC_SLSH), KC_RBRC, RALT(KC_NUBS), KC_HOME, KC_PGDN, KC_PGUP, KC_END, RALT(KC_6), KC_TRNS, KC_CAPS, LSFT(KC_TAB), LSFT(KC_DEL), LSFT(KC_ENT), KC_TRNS, RSFT(KC_RCTL), RSFT(KC_LALT), RSFT(KC_RALT), RSFT(KC_RGUI), KC_TRNS), +[4] = LAYOUT(RALT(KC_ESC), RALT(KC_Q), RALT(KC_W), RALT(KC_E), RALT(KC_R), RALT(KC_T), RALT(KC_Y), RALT(KC_U), RALT(KC_I), RALT(KC_O), RALT(KC_P), RALT(KC_A), RALT(KC_S), RALT(KC_D), RALT(KC_F), RALT(KC_G), RALT(KC_H), RALT(KC_J), RALT(KC_K), RALT(KC_L), RALT(KC_8), RALT(KC_9), LSFT(KC_0), RALT(KC_Z), RALT(KC_X), RALT(KC_C), RALT(KC_V), RALT(KC_B), RALT(KC_N), RALT(KC_M), RALT(KC_COMM), RALT(KC_DOT), RALT(KC_6), KC_NO, RALT(KC_ENT), RALT(KC_TAB), RALT(KC_DEL), RALT(KC_SPC), RALT(KC_LSFT), RALT(KC_LCTL), RALT(KC_LALT), KC_TRNS, RALT(KC_LGUI), KC_NO), +[5] = LAYOUT(KC_0, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_F11, KC_F12, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_NO, KC_TRNS, KC_TAB, KC_BSPC, KC_SPC, KC_LSFT, KC_LCTL, KC_LALT, KC_RALT, KC_LGUI, KC_NO) +}; diff --git a/keyboards/handwired/hacked_motospeed/keymaps/german/layers.json b/keyboards/handwired/hacked_motospeed/keymaps/german/layers.json new file mode 100644 index 0000000000..d2ff7c5b46 --- /dev/null +++ b/keyboards/handwired/hacked_motospeed/keymaps/german/layers.json @@ -0,0 +1 @@ +[["KC_ESC", "KC_Q", "KC_W", "KC_E", "KC_R", "KC_T", "KC_Y", "KC_U", "KC_I", "KC_O", "KC_P", "KC_A", "KC_S", "KC_D", "KC_F", "KC_G", "KC_H", "KC_J", "KC_K", "KC_L", "LSFT(KC_8)", "LSFT(KC_9)", "KC_PEQL", "KC_Z", "KC_X", "KC_C", "KC_V", "KC_B", "KC_N", "KC_M", "KC_COMM", "KC_DOT", "LSFT(KC_MINS)", "MO(2)", "MO(6)", "KC_TAB", "KC_BSPC", "KC_SPC", "MO(1)", "KC_LCTL", "KC_LALT", "MO(4)", "KC_LGUI", "MO(2)"], ["LALT(KC_F4)", "LSFT(KC_Q)", "LSFT(KC_W)", "LSFT(KC_E)", "LSFT(KC_R)", "LSFT(KC_T)", "LSFT(KC_Y)", "LSFT(KC_U)", "LSFT(KC_I)", "LSFT(KC_O)", "LSFT(KC_P)", "LSFT(KC_A)", "LSFT(KC_S)", "LSFT(KC_D)", "LSFT(KC_F)", "LSFT(KC_G)", "LSFT(KC_H)", "LSFT(KC_J)", "LSFT(KC_K)", "LSFT(KC_L)", "RALT(KC_7)", "RALT(KC_0)", "KC_NUHS", "LSFT(KC_Z)", "LSFT(KC_X)", "LSFT(KC_C)", "LSFT(KC_V)", "LSFT(KC_B)", "LSFT(KC_N)", "LSFT(KC_M)", "LSFT(KC_COMM)", "LSFT(KC_DOT)", "LSFT(KC_1)", "MO(3)", "TG(6)", "LSFT(KC_TAB)", "KC_DEL", "KC_ENT", "KC_TRNS", "LSFT(KC_LCTL)", "LSFT(KC_LALT)", "LSFT(KC_RALT)", "LSFT(KC_LGUI)", "MO(3)"], ["LSFT(KC_GRV)", "RALT(KC_Q)", "KC_JYEN", "RALT(KC_E)", "LSFT(KC_4)", "LSFT(KC_5)", "LSFT(KC_6)", "KC_LBRC", "KC_UP", "KC_SCLN", "KC_PSCR", "KC_QUOT", "KC_MINS", "LSFT(KC_7)", "LSFT(KC_2)", "LSFT(KC_NUHS)", "LSFT(KC_3)", "KC_LEFT", "KC_DOWN", "KC_RGHT", "KC_NUBS", "LSFT(KC_NUBS)", "RALT(KC_RBRC)", "KC_GRV", "LSFT(KC_RBRC)", "KC_SLSH", "KC_RBRC", "RALT(KC_NUBS)", "KC_HOME", "KC_PGDN", "KC_PGUP", "KC_END", "RALT(KC_6)", "KC_TRNS", "KC_CAPS", "KC_TAB", "KC_DEL", "KC_ENT", "MO(3)", "OUT_BT", "OUT_USB", "OUT_AUTO", "BL_STEP", "KC_TRNS"], ["LSFT(KC_GRV)", "RALT(KC_Q)", "KC_JYEN", "RALT(KC_E)", "LSFT(KC_4)", "LSFT(KC_5)", "LSFT(KC_6)", "LSFT(KC_LBRC)", "KC_UP", "LSFT(KC_SCLN)", "KC_PSCR", "LSFT(KC_QUOT)", "KC_MINS", "RALT(KC_MINS)", "LSFT(KC_EQL)", "KC_EQL", "LSFT(KC_3)", "KC_LEFT", "KC_DOWN", "KC_RGHT", "RALT(KC_8)", "RALT(KC_9)", "RALT(KC_RBRC)", "KC_GRV", "LSFT(KC_RBRC)", "LSFT(KC_SLSH)", "KC_RBRC", "RALT(KC_NUBS)", "KC_HOME", "KC_PGDN", "KC_PGUP", "KC_END", "RALT(KC_6)", "KC_TRNS", "KC_CAPS", "LSFT(KC_TAB)", "LSFT(KC_DEL)", "LSFT(KC_ENT)", "KC_TRNS", "RSFT(KC_RCTL)", "RSFT(KC_LALT)", "RSFT(KC_RALT)", "RSFT(KC_RGUI)", "KC_TRNS"], ["RALT(KC_ESC)", "RALT(KC_Q)", "RALT(KC_W)", "RALT(KC_E)", "RALT(KC_R)", "RALT(KC_T)", "RALT(KC_Y)", "RALT(KC_U)", "RALT(KC_I)", "RALT(KC_O)", "RALT(KC_P)", "RALT(KC_A)", "RALT(KC_S)", "RALT(KC_D)", "RALT(KC_F)", "RALT(KC_G)", "RALT(KC_H)", "RALT(KC_J)", "RALT(KC_K)", "RALT(KC_L)", "RALT(KC_8)", "RALT(KC_9)", "LSFT(KC_0)", "RALT(KC_Z)", "RALT(KC_X)", "RALT(KC_C)", "RALT(KC_V)", "RALT(KC_B)", "RALT(KC_N)", "RALT(KC_M)", "RALT(KC_COMM)", "RALT(KC_DOT)", "RALT(KC_6)", "KC_NO", "RALT(KC_ENT)", "RALT(KC_TAB)", "RALT(KC_DEL)", "RALT(KC_SPC)", "RALT(KC_LSFT)", "RALT(KC_LCTL)", "RALT(KC_LALT)", "KC_TRNS", "RALT(KC_LGUI)", "KC_NO"], ["KC_0", "KC_F1", "KC_F2", "KC_F3", "KC_F4", "KC_F5", "KC_F6", "KC_F7", "KC_F8", "KC_F9", "KC_F10", "KC_1", "KC_2", "KC_3", "KC_4", "KC_5", "KC_6", "KC_7", "KC_8", "KC_9", "KC_F11", "KC_F12", "KC_F13", "KC_F14", "KC_F15", "KC_F16", "KC_F17", "KC_F18", "KC_F19", "KC_F20", "KC_F21", "KC_F22", "KC_F23", "KC_NO", "KC_TRNS", "KC_TAB", "KC_BSPC", "KC_SPC", "KC_LSFT", "KC_LCTL", "KC_LALT", "KC_RALT", "KC_LGUI", "KC_NO"]]
\ No newline at end of file diff --git a/keyboards/handwired/hacked_motospeed/keymaps/german/readme.md b/keyboards/handwired/hacked_motospeed/keymaps/german/readme.md new file mode 100755 index 0000000000..fd07b155fb --- /dev/null +++ b/keyboards/handwired/hacked_motospeed/keymaps/german/readme.md @@ -0,0 +1,13 @@ +# Generated Keymap Layout + +This layout was generated by the QMK API. You can find the JSON data used to +generate this keymap in the file layers.json. + +To make use of this file you will need follow the following steps: + +* Download or Clone QMK Firmware: <https://github.com/qmk/qmk_firmware/> +* Extract QMK Firmware to a location on your hard drive +* Copy this folder into %s +* You are now ready to compile or use your keymap with the source + +More information can be found in the QMK docs: <https://docs.qmk.fm>
\ No newline at end of file diff --git a/keyboards/handwired/hacked_motospeed/rules.mk b/keyboards/handwired/hacked_motospeed/rules.mk index 1dc955718f..7cb9e914ec 100644 --- a/keyboards/handwired/hacked_motospeed/rules.mk +++ b/keyboards/handwired/hacked_motospeed/rules.mk @@ -1,43 +1,5 @@ # MCU name MCU = at90usb1286 -#MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay @@ -45,20 +7,10 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=1024 - - # Build Options # change yes to no to disable # @@ -70,7 +22,7 @@ COMMAND_ENABLE = yes # Commands for debug and configuration # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = yes # USB Nkey Rollover +NKRO_ENABLE = no # USB Nkey Rollover BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality on B7 by default RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) @@ -78,4 +30,6 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches -HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
\ No newline at end of file +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) +NO_USB_STARTUP_CHECK = yes # Disable initialization only when usb is plugged in +BLUETOOTH = RN42 diff --git a/keyboards/handwired/hexon38/rules.mk b/keyboards/handwired/hexon38/rules.mk index 2b6f17afc2..fb5e1b0c9b 100644 --- a/keyboards/handwired/hexon38/rules.mk +++ b/keyboards/handwired/hexon38/rules.mk @@ -1,54 +1,16 @@ -# see https://github.com/pepaslabs/hexon38 - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay - # Enabled build options: BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) diff --git a/keyboards/handwired/hnah108/config.h b/keyboards/handwired/hnah108/config.h new file mode 100644 index 0000000000..b2d84e3e38 --- /dev/null +++ b/keyboards/handwired/hnah108/config.h @@ -0,0 +1,245 @@ +/* +Copyright 2019 HnahKB + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0002 +#define MANUFACTURER HnahKB +#define PRODUCT Hnah108 +#define DESCRIPTION Fullsize PCB keyboard + +/* key matrix size */ +#define MATRIX_ROWS 10 +#define MATRIX_COLS 11 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS \ + { F7, F6, F5, F4, F1, C7, B4, B5, B6, C6 } +#define MATRIX_COL_PINS \ + { F0, E6, B0, D0, D1, D2, D3, D5, D4, D6, D7 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + + +#define ENCODERS_PAD_A { B2 } +#define ENCODERS_PAD_B { B3 } + +#define ENCODER_RESOLUTION 4 + +#define BACKLIGHT_PIN B7 +#define BACKLIGHT_BREATHING +#define BACKLIGHT_LEVELS 4 + +#define RGB_DI_PIN E2 +#define DRIVER_LED_TOTAL 31 + +// #define RGBLIGHT_HUE_STEP 8 +// #define RGBLIGHT_SAT_STEP 8 +// #define RGBLIGHT_VAL_STEP 8 +// #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ +// #define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ +// /*== or choose animations ==*/ +// #define RGBLIGHT_EFFECT_BREATHING +// #define RGBLIGHT_EFFECT_RAINBOW_MOOD +// #define RGBLIGHT_EFFECT_RAINBOW_SWIRL +// #define RGBLIGHT_EFFECT_SNAKE +// #define RGBLIGHT_EFFECT_KNIGHT +// #define RGBLIGHT_EFFECT_CHRISTMAS +// #define RGBLIGHT_EFFECT_STATIC_GRADIENT +// #define RGBLIGHT_EFFECT_RGB_TEST +// #define RGBLIGHT_EFFECT_ALTERNATING +// /*== customize breathing effect ==*/ +// /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ +// #define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 +// /*==== use exp() and sin() ====*/ +// #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 +// #define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +/* defined by default; to change, uncomment and set to the combination you want */ +// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP H +//#define MAGIC_KEY_HELP_ALT SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER0_ALT GRAVE +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER B +//#define MAGIC_KEY_BOOTLOADER_ALT ESC +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_EEPROM_CLEAR BSPACE +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +/* + * HD44780 LCD Display Configuration + */ +/* +#define LCD_LINES 2 //< number of visible lines of the display +#define LCD_DISP_LENGTH 16 //< visibles characters per line of the display + +#define LCD_IO_MODE 1 //< 0: memory mapped mode, 1: IO port mode + +#if LCD_IO_MODE +#define LCD_PORT PORTB //< port for the LCD lines +#define LCD_DATA0_PORT LCD_PORT //< port for 4bit data bit 0 +#define LCD_DATA1_PORT LCD_PORT //< port for 4bit data bit 1 +#define LCD_DATA2_PORT LCD_PORT //< port for 4bit data bit 2 +#define LCD_DATA3_PORT LCD_PORT //< port for 4bit data bit 3 +#define LCD_DATA0_PIN 4 //< pin for 4bit data bit 0 +#define LCD_DATA1_PIN 5 //< pin for 4bit data bit 1 +#define LCD_DATA2_PIN 6 //< pin for 4bit data bit 2 +#define LCD_DATA3_PIN 7 //< pin for 4bit data bit 3 +#define LCD_RS_PORT LCD_PORT //< port for RS line +#define LCD_RS_PIN 3 //< pin for RS line +#define LCD_RW_PORT LCD_PORT //< port for RW line +#define LCD_RW_PIN 2 //< pin for RW line +#define LCD_E_PORT LCD_PORT //< port for Enable line +#define LCD_E_PIN 1 //< pin for Enable line +#endif +*/ diff --git a/keyboards/handwired/hnah108/hnah108.c b/keyboards/handwired/hnah108/hnah108.c new file mode 100644 index 0000000000..a05cc4fe12 --- /dev/null +++ b/keyboards/handwired/hnah108/hnah108.c @@ -0,0 +1,43 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "hnah108.h" + + + +led_config_t g_led_config = { { + //Key Matrix to LED Index + { 18, 17, 16,NO_LED, 15, 14,NO_LED,NO_LED, 13, 12,NO_LED}, + {NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED}, + {19, NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED}, + {NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED}, + {20, NO_LED,NO_LED,NO_LED,NO_LED,24 ,NO_LED,NO_LED,26 ,NO_LED,NO_LED}, + { 21, 22, 23, 25, 27,NO_LED, 28, 29,NO_LED, 0, 1}, + { 11, 10,NO_LED, 9,NO_LED, 8,NO_LED, 7, 6,NO_LED, 5}, + {NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED, 4}, + {NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED, 3}, + {NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED,NO_LED, 2} +}, { + //LED Index to Physical Positon + { 0, 0}, { 18, 0}, { 37, 0 }, { 56, 0}, { 74, 0}, { 93, 0}, { 112, 0 }, { 130, 0}, { 149, 0}, { 168, 0}, { 186, 0 }, { 205, 0}, + { 0, 25} , { 205, 25}, + { 0, 51} , { 205, 51}, + { 0, 63} , { 18, 63}, { 37, 63}, { 56, 63}, { 74, 63}, { 93, 63}, { 112, 63}, { 130, 63},{ 149, 63}, { 168, 63}, { 186, 63 }, { 205, 63}, +}, { + 1,1,1,1,1,1,1,1,1,1,1,1,1, + 1,1, + 1,1, + 1,1,1,1,1,1,1,1,1,1,1,1,1, +} };
\ No newline at end of file diff --git a/keyboards/handwired/hnah108/hnah108.h b/keyboards/handwired/hnah108/hnah108.h new file mode 100644 index 0000000000..9ea34b83ad --- /dev/null +++ b/keyboards/handwired/hnah108/hnah108.h @@ -0,0 +1,72 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + + +#define LAYOUT_all( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61, k62, k63, k64, k65, k66, k67, k68, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72, k73, k74, k75, k76, k77, k78, k69, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, k82, k83, k84, k85, k86, k87, k79, k6A, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91, k93, k94, k96, k97, k88, \ + k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k90, k92, k95, k98, k99, k89, k7A, \ + k50, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k9A, k8A \ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A }, \ + { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A }, \ + { k50, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A }, \ + { k60, k61, k62, k63, k64, k65, k66, k67, k68, k69, k6A }, \ + { k70, k71, k72, k73, k74, k75, k76, k77, k78, k79, k7A }, \ + { k80, k81, k82, k83, k84, k85, k86, k87, k88, k89, k8A }, \ + { k90, k91, k92, k93, k94, k95, k96, k97, k98, k99, k9A }, \ +} + +#define LAYOUT_fullsize_iso( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61, k62, k63, k64, k65, k66, k67, k68, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72, k73, k74, k75, k76, k77, k78, k69, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, k83, k84, k85, k86, k87, k79, k6A, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91, k93, k94, k96, k97, k88, \ + k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k90, k92, k95, k98, k99, k89, k7A, \ + k50, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k9A, k8A \ +) LAYOUT_all( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61, k62, k63, k64, k65, k66, k67, k68, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72, k73, k74, k75, k76, k77, k78, k69, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, KC_NO, k83, k84, k85, k86, k87, k79, k6A, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91, k93, k94, k96, k97, k88, \ + k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k90, k92, k95, k98, k99, k89, k7A, \ + k50, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k9A, k8A \ +) + +#define LAYOUT_fullsize_ansi( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61, k62, k63, k64, k65, k66, k67, k68, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72, k73, k74, k75, k76, k77, k78, k69, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, k82, k83, k84, k85, k86, k87, k79, k6A, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91, k94, k96, k97, k88, \ + k40, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k90, k92, k95, k98, k99, k89, k7A, \ + k50, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k9A, k8A \ +) LAYOUT_all( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k60, k61, k62, k63, k64, k65, k66, k67, k68, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k70, k71, k72, k73, k74, k75, k76, k77, k78, k69, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k80, k81, k82, k83, k84, k85, k86, k87, k79, k6A, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k91,KC_NO,k94, k96, k97, k88, \ + k40,KC_NO,k42, k43, k44, k45, k46, k47, k48, k49, k4A, k90, k92, k95, k98, k99, k89, k7A, \ + k50, k51, k52, k53, k54, k55, k56, k57, k58, k59, k5A, k9A, k8A \ +) diff --git a/keyboards/handwired/hnah108/info.json b/keyboards/handwired/hnah108/info.json new file mode 100644 index 0000000000..a8671a870c --- /dev/null +++ b/keyboards/handwired/hnah108/info.json @@ -0,0 +1,18 @@ +{ + "keyboard_name": "hnah108", + "url": "", + "maintainer": "HnahKB", + "width": 22.5, + "height": 6.25, + "layouts": { + "LAYOUT_all": { + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"x":18.5, "y":0}, {"x":19.5, "y":0}, {"x":20.5, "y":0}, {"x":21.5, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"|", "x":13.5, "y":2.25, "w":1.5}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"@", "x":11.75, "y":3.25}, {"label":"~", "x":12.75, "y":3.25}, {"label":"Enter", "x":13.75, "y":3.25, "w":1.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":1.25}, {"label":"|", "x":1.25, "y":4.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}] + }, + "LAYOUT_fullsize_iso": { + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"x":18.5, "y":0}, {"x":19.5, "y":0}, {"x":20.5, "y":0}, {"x":21.5, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"Enter", "x":13.75, "y":2.25, "w":1.25, "h":2}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"@", "x":11.75, "y":3.25}, {"label":"~", "x":12.75, "y":3.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":1.25}, {"label":"|", "x":1.25, "y":4.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}] + }, + "LAYOUT_fullsize_ansi": { + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"x":18.5, "y":0}, {"x":19.5, "y":0}, {"x":20.5, "y":0}, {"x":21.5, "y":0}, {"label":"~", "x":0, "y":1.25}, {"label":"!", "x":1, "y":1.25}, {"label":"@", "x":2, "y":1.25}, {"label":"#", "x":3, "y":1.25}, {"label":"$", "x":4, "y":1.25}, {"label":"%", "x":5, "y":1.25}, {"label":"^", "x":6, "y":1.25}, {"label":"&", "x":7, "y":1.25}, {"label":"*", "x":8, "y":1.25}, {"label":"(", "x":9, "y":1.25}, {"label":")", "x":10, "y":1.25}, {"label":"_", "x":11, "y":1.25}, {"label":"+", "x":12, "y":1.25}, {"label":"Backspace", "x":13, "y":1.25, "w":2}, {"label":"Insert", "x":15.25, "y":1.25}, {"label":"Home", "x":16.25, "y":1.25}, {"label":"PgUp", "x":17.25, "y":1.25}, {"label":"Num Lock", "x":18.5, "y":1.25}, {"label":"/", "x":19.5, "y":1.25}, {"label":"*", "x":20.5, "y":1.25}, {"label":"-", "x":21.5, "y":1.25}, {"label":"Tab", "x":0, "y":2.25, "w":1.5}, {"label":"Q", "x":1.5, "y":2.25}, {"label":"W", "x":2.5, "y":2.25}, {"label":"E", "x":3.5, "y":2.25}, {"label":"R", "x":4.5, "y":2.25}, {"label":"T", "x":5.5, "y":2.25}, {"label":"Y", "x":6.5, "y":2.25}, {"label":"U", "x":7.5, "y":2.25}, {"label":"I", "x":8.5, "y":2.25}, {"label":"O", "x":9.5, "y":2.25}, {"label":"P", "x":10.5, "y":2.25}, {"label":"{", "x":11.5, "y":2.25}, {"label":"}", "x":12.5, "y":2.25}, {"label":"|", "x":13.5, "y":2.25, "w":1.5}, {"label":"Delete", "x":15.25, "y":2.25}, {"label":"End", "x":16.25, "y":2.25}, {"label":"PgDn", "x":17.25, "y":2.25}, {"label":"7", "x":18.5, "y":2.25}, {"label":"8", "x":19.5, "y":2.25}, {"label":"9", "x":20.5, "y":2.25}, {"label":"+", "x":21.5, "y":2.25, "h":2}, {"label":"Caps Lock", "x":0, "y":3.25, "w":1.75}, {"label":"A", "x":1.75, "y":3.25}, {"label":"S", "x":2.75, "y":3.25}, {"label":"D", "x":3.75, "y":3.25}, {"label":"F", "x":4.75, "y":3.25}, {"label":"G", "x":5.75, "y":3.25}, {"label":"H", "x":6.75, "y":3.25}, {"label":"J", "x":7.75, "y":3.25}, {"label":"K", "x":8.75, "y":3.25}, {"label":"L", "x":9.75, "y":3.25}, {"label":":", "x":10.75, "y":3.25}, {"label":"\"", "x":11.75, "y":3.25}, {"label":"Enter", "x":12.75, "y":3.25, "w":2.25}, {"label":"4", "x":18.5, "y":3.25}, {"label":"5", "x":19.5, "y":3.25}, {"label":"6", "x":20.5, "y":3.25}, {"label":"Shift", "x":0, "y":4.25, "w":2.25}, {"label":"Z", "x":2.25, "y":4.25}, {"label":"X", "x":3.25, "y":4.25}, {"label":"C", "x":4.25, "y":4.25}, {"label":"V", "x":5.25, "y":4.25}, {"label":"B", "x":6.25, "y":4.25}, {"label":"N", "x":7.25, "y":4.25}, {"label":"M", "x":8.25, "y":4.25}, {"label":"<", "x":9.25, "y":4.25}, {"label":">", "x":10.25, "y":4.25}, {"label":"?", "x":11.25, "y":4.25}, {"label":"Shift", "x":12.25, "y":4.25, "w":2.75}, {"label":"\u2191", "x":16.25, "y":4.25}, {"label":"1", "x":18.5, "y":4.25}, {"label":"2", "x":19.5, "y":4.25}, {"label":"3", "x":20.5, "y":4.25}, {"label":"Enter", "x":21.5, "y":4.25, "h":2}, {"label":"Ctrl", "x":0, "y":5.25, "w":1.25}, {"label":"Win", "x":1.25, "y":5.25, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.25, "w":1.25}, {"x":3.75, "y":5.25, "w":6.25}, {"label":"Alt", "x":10, "y":5.25, "w":1.25}, {"label":"Win", "x":11.25, "y":5.25, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.25, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.25, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.25}, {"label":"\u2193", "x":16.25, "y":5.25}, {"label":"\u2192", "x":17.25, "y":5.25}, {"label":"0", "x":18.5, "y":5.25, "w":2}, {"label":".", "x":20.5, "y":5.25}] + } + } +}
\ No newline at end of file diff --git a/keyboards/handwired/hnah108/keymaps/default/config.h b/keyboards/handwired/hnah108/keymaps/default/config.h new file mode 100644 index 0000000000..348d7c5513 --- /dev/null +++ b/keyboards/handwired/hnah108/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/hnah108/keymaps/default/keymap.c b/keyboards/handwired/hnah108/keymaps/default/keymap.c new file mode 100644 index 0000000000..6d8fe072c1 --- /dev/null +++ b/keyboards/handwired/hnah108/keymaps/default/keymap.c @@ -0,0 +1,79 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +enum hnah_layers{ + _QWERTY, + _FN +}; + +#define LOWER MO(_FN) +#define RAISE MO(_QWERTY) + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_QWERTY] = LAYOUT_all( /* Base */ + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS, KC_MYCM, KC_CALC, KC_MPLY, LOWER, + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_INS, KC_HOME, KC_PGUP, KC_NLCK, KC_PSLS, KC_PAST, KC_PMNS, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_SLSH, KC_DEL, KC_END, KC_PGDN, KC_P7, KC_P8, KC_P9, KC_PPLS, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NUHS, KC_ENT, KC_P4, KC_P5, KC_P6, + KC_LSFT, KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_BSLS, KC_RSFT, KC_UP, KC_P1, KC_P2, KC_P3, KC_PENT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_APP, KC_RGUI, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT, KC_P0, KC_PDOT + ), + + [_FN] = LAYOUT_all( /* Base */ + RESET, BL_STEP,RGB_TOG, RGB_MOD, RGB_RMOD, RGB_HUI, RGB_HUD, RGB_VAI, RGB_VAD, RGB_SPI, RGB_SPD, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_VOLD, KC_VOLU, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRIU, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_BRID, _______, _______, _______ + ), +}; + +void encoder_update_user(uint8_t index, bool clockwise) { + if (index == 0) { + if (IS_LAYER_ON(_FN)) { + if (clockwise) { + tap_code(KC_BRIU); + } else { + tap_code(KC_BRID); + } + } else { + if (clockwise) { + tap_code(KC_VOLU); + + } else { + tap_code(KC_VOLD); + } + } + } +} + +void rgb_matrix_indicators_user(void) +{ + if IS_HOST_LED_ON(USB_LED_CAPS_LOCK) + { + rgb_matrix_set_color(30, 0x00, 0xFF, 0x00); + } else if IS_HOST_LED_ON(USB_LED_NUM_LOCK) + { + rgb_matrix_set_color(30, 0xFF, 0x00, 0x00); + } else if IS_HOST_LED_ON(USB_LED_SCROLL_LOCK) + { + rgb_matrix_set_color(30, 0x00, 0x00, 0xFF); + } else { + rgb_matrix_set_color(30, 0x00, 0x00, 0x00); + } +}
\ No newline at end of file diff --git a/keyboards/handwired/hnah108/keymaps/default/readme.md b/keyboards/handwired/hnah108/keymaps/default/readme.md new file mode 100644 index 0000000000..37477efdb1 --- /dev/null +++ b/keyboards/handwired/hnah108/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for hnah108
\ No newline at end of file diff --git a/keyboards/handwired/hnah108/readme.md b/keyboards/handwired/hnah108/readme.md new file mode 100644 index 0000000000..d4cd6a1802 --- /dev/null +++ b/keyboards/handwired/hnah108/readme.md @@ -0,0 +1,14 @@ +# hnah108 + + + +A Full size keyboard pcb with rotary encoder. Used ws2811 IC as a indicator LED driver + +Keyboard Maintainer: [HnahKB](https://github.com/vuhopkep) +Hardware Supported: Hnah108 v1 + +Make example for this keyboard (after setting up your build environment): + + make handwired/hnah108:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/hnah108/rules.mk b/keyboards/handwired/hnah108/rules.mk new file mode 100644 index 0000000000..8e486c594b --- /dev/null +++ b/keyboards/handwired/hnah108/rules.mk @@ -0,0 +1,35 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) +ENCODER_ENABLE = yes +RGB_MATRIX_ENABLE = WS2812 diff --git a/keyboards/handwired/hnah40/config.h b/keyboards/handwired/hnah40/config.h index b7a4105d00..3d3c05fd42 100644 --- a/keyboards/handwired/hnah40/config.h +++ b/keyboards/handwired/hnah40/config.h @@ -78,6 +78,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. */ // #define GRAVE_ESC_CTRL_OVERRIDE +#define USB_MAX_POWER_CONSUMPTION 100 + /* * Force NKRO * diff --git a/keyboards/handwired/hnah40/info.json b/keyboards/handwired/hnah40/info.json index 6a577a5207..f9664d22c9 100644 --- a/keyboards/handwired/hnah40/info.json +++ b/keyboards/handwired/hnah40/info.json @@ -39,7 +39,8 @@ {"label":"N", "x":6.75, "y":2}, {"label":"M", "x":7.75, "y":2}, {"label":",", "x":8.75, "y":2}, - {"label":"Shift", "x":9.75, "y":2, "w":2.25}, + {"label":".", "x":9.75, "y":2}, + {"label":"Shift", "x":10.75, "y":2, "w":1.25}, {"label":"Ctrl", "x":0, "y":3, "w":1.25}, {"label":"Win", "x":1.25, "y":3, "w":1.5}, {"label":"Alt", "x":2.75, "y":3, "w":1.25}, @@ -51,4 +52,4 @@ ] } } -}
\ No newline at end of file +} diff --git a/keyboards/handwired/hnah40/rules.mk b/keyboards/handwired/hnah40/rules.mk index efd11bfa5c..bbdf5176c4 100644 --- a/keyboards/handwired/hnah40/rules.mk +++ b/keyboards/handwired/hnah40/rules.mk @@ -1,44 +1,15 @@ # MCU name MCU = atmega328p -PROTOCOL = VUSB -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -BOOTLOADER = bootloadHID +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = USBasp # Flash program via avrdude, but default command is not suitable. # You can use hnah40:default:program @@ -69,5 +40,3 @@ BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) -NO_UART = yes -NO_SUSPEND_POWER_DOWN = yes
\ No newline at end of file diff --git a/keyboards/handwired/hnah40/usbconfig.h b/keyboards/handwired/hnah40/usbconfig.h index cbd37c34dc..b26a3c7d67 100644 --- a/keyboards/handwired/hnah40/usbconfig.h +++ b/keyboards/handwired/hnah40/usbconfig.h @@ -109,21 +109,10 @@ section at the end of this file). * (e.g. HID), but never want to send any data. This option saves a couple * of bytes in flash memory and the transmit buffers in RAM. */ -#define USB_CFG_INTR_POLL_INTERVAL 1 -/* If you compile a version with endpoint 1 (interrupt-in), this is the poll - * interval. The value is in milliseconds and must not be less than 10 ms for - * low speed devices. - */ #define USB_CFG_IS_SELF_POWERED 0 /* Define this to 1 if the device has its own power supply. Set it to 0 if the * device is powered from the USB bus. */ -// max power draw with maxed white underglow measured at 120 mA (peaks) -#define USB_CFG_MAX_BUS_POWER 100 -/* Set this variable to the maximum USB bus power consumption of your device. - * The value is in milliamperes. [It will be divided by two since USB - * communicates power requirements in units of 2 mA.] - */ #define USB_CFG_IMPLEMENT_FN_WRITE 1 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out * transfers. Set it to 0 if you don't need it and want to save a couple of @@ -239,7 +228,7 @@ section at the end of this file). * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand * the implications! */ -#define USB_CFG_DEVICE_VERSION 0x00, 0x01 +#define USB_CFG_DEVICE_VERSION (DEVICE_VER & 0xFF), ((DEVICE_VER >> 8) & 0xFF) /* Version number of the device: Minor number first, then major number. */ #define USB_CFG_VENDOR_NAME 'H','n','a','h','K','B' diff --git a/keyboards/handwired/hnah40rgb/config.h b/keyboards/handwired/hnah40rgb/config.h new file mode 100644 index 0000000000..7741f3965f --- /dev/null +++ b/keyboards/handwired/hnah40rgb/config.h @@ -0,0 +1,68 @@ +/* +Copyright 2019 HnahKB + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER HnahKB +#define PRODUCT Hnah40V2 +#define DESCRIPTION A custom rgb keyboard + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 11 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS \ + { B7, D7, F1, F0 } +#define MATRIX_COL_PINS \ + { D5, D6, D3, D2, B6, C6, C7, F7, F6, F5, F4 } + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + +#ifdef RGB_MATRIX_ENABLE +#define RGB_DI_PIN E2 +#define DRIVER_LED_TOTAL 50 +#define RGB_MATRIX_KEYPRESSES // reacts to keypresses +#define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (instead of keypresses) +#define RGB_MATRIX_FRAMEBUFFER_EFFECTS +#define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects +#define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended +#define RGB_MATRIX_LED_FLUSH_LIMIT 16 // limits in milliseconds how frequently an animation will update the LEDs. 16 (16ms) is equivalent to limiting to 60fps (increases keyboard responsiveness) +#define RGB_MATRIX_MAXIMUM_BRIGHTNESS 200 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255 +#define RGB_MATRIX_STARTUP_MODE RGB_MATRIX_CYCLE_PINWHEEL // Sets the default mode, if none has been set +#endif diff --git a/keyboards/handwired/hnah40rgb/hnah40rgb.c b/keyboards/handwired/hnah40rgb/hnah40rgb.c new file mode 100644 index 0000000000..2bf1373d91 --- /dev/null +++ b/keyboards/handwired/hnah40rgb/hnah40rgb.c @@ -0,0 +1,47 @@ +#include "hnah40rgb.h" +#ifdef RGB_MATRIX_ENABLE +#if defined (ansi) +led_config_t g_led_config = { { + //Key Matrix to LED Index + {0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10}, + {22, 21, 20, 19, 18, 17, 16, 15, 14, 13, 12 }, + {23, 24, 25, 26, 27, 28, 29, 30, 31, NO_LED, 34}, + {43, 42, 41, NO_LED, NO_LED, NO_LED, 38, NO_LED, 36, 35, 11} +}, { + //LED Index to Physical Positon + { 0, 0}, { 20, 0}, { 40, 0 }, { 61, 0 }, { 81, 0}, { 101, 0}, { 122, 0}, { 142, 0}, { 162, 0}, { 183, 0}, { 224, 0}, { 224, 0}, + {224, 21}, {183, 21}, {162,21 }, {142, 21}, {122,21}, { 101,21}, { 81 ,21}, { 61 ,21}, { 40 ,21}, { 20 ,21}, { 0 ,21}, + { 0, 42}, { 20, 42}, { 40,42 }, { 61, 42}, { 81,42}, { 101,42}, { 122,42}, { 142,42}, { 162,42}, { 183,42}, { 224,42}, + {224, 64}, {224, 64}, {181,64 }, {162, 64}, {122,64}, {101,64}, { 61,64}, { 40,64}, { 20,64}, { 0,64}, + { 0,64}, { 0,0}, { 224,10}, { 224,18}, { 224,30}, { 224,47}, +}, { + 1, 4, 4, 4, 4, 4, 4, 4, 4, 4, 1, + 1, 4, 4, 4, 4, 4, 4, 4, 4, 4, 1, + 1, 4, 4, 4, 4, 4, 4, 4, 4, 4, 1, + 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, + 1, 1, 1, 1, 1, 1, +} }; + +#else +led_config_t g_led_config = { { + //Key Matrix to LED Index + {0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10}, + {22, 21, 20, 19, 18, 17, 16, 15, 14, 13, 12 }, + {23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 34}, + {43, 42, 41, NO_LED, 40, 39, 38, 37, 36, 35, 11} +}, { + //LED Index to Physical Positon + { 0, 0}, { 20, 0}, { 40, 0 }, { 61, 0 }, { 81, 0}, { 101, 0}, { 122, 0}, { 142, 0}, { 162, 0}, { 183, 0}, { 224, 0}, { 224, 0}, + {224, 21}, {183, 21}, {162,21 }, {142, 21}, {122,21}, { 101,21}, { 81 ,21}, { 61 ,21}, { 40 ,21}, { 20 ,21}, { 0 ,21}, + { 0, 42}, { 20, 42}, { 40,42 }, { 61, 42}, { 81,42}, { 101,42}, { 122,42}, { 142,42}, { 162,42}, { 183,42}, { 224,42}, + {224, 64}, {224, 64}, {181,64 }, {162, 64}, {122,64}, {101,64}, { 61,64}, { 40,64}, { 20,64}, { 0,64}, + { 0,64}, { 0,0}, { 224,10}, { 224,18}, { 224,30}, { 224,47}, +}, { + 1, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, + 1, 1, 4, 4, 4, 4, 4, 4, 4, 4, 4, + 1, 1, 4, 4, 4, 4, 4, 4, 4, 4, 4, + 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, + 1, 1, 1, 1, 1, 1, +} }; +#endif +#endif
\ No newline at end of file diff --git a/keyboards/handwired/hnah40rgb/hnah40rgb.h b/keyboards/handwired/hnah40rgb/hnah40rgb.h new file mode 100644 index 0000000000..182c68603a --- /dev/null +++ b/keyboards/handwired/hnah40rgb/hnah40rgb.h @@ -0,0 +1,44 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +#define LAYOUT_all( \ +k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k10, k41, \ +k11, k12, k13, k14, k15, k16, k17, k18, k19, k20, k21, k22, \ +k23, k24, k25, k26, k27, k28, k29, k30, k31, k32, k33,\ +k34, k35, k36, k37, k38, k39, k40 \ +) \ +{ \ + {k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k10}, \ + {k11, k12, k13, k14, k15, k16, k17, k18, k19, k20, k21}, \ + {k22, k23, k24, k25, k26, k27, k28, k29, k30, k31, k32}, \ + {k33, k34, k35, KC_NO,k36, KC_NO, k37, k38, k39, k40, k41}, \ +} + +#define LAYOUT_ansi( \ +k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k10, k41, \ +k11, k12, k13, k14, k15, k16, k17, k18, k19, k20, k21, \ +k22, k23, k24, k25, k26, k27, k28, k29, k30, k32,\ +k33, k34, k35, k38, k39, k40 \ +) \ +{ \ + {k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k10}, \ + {k11, k12, k13, k14, k15, k16, k17, k18, k19, k20, k21}, \ + {k22, k23, k24, k25, k26, k27, k28, k29, k30, KC_NO, k32}, \ + {k33, k34, k35, KC_NO, KC_NO, KC_NO, k38, KC_NO, k39, k40, k41}, \ +} diff --git a/keyboards/handwired/hnah40rgb/info.json b/keyboards/handwired/hnah40rgb/info.json new file mode 100644 index 0000000000..dd1b423259 --- /dev/null +++ b/keyboards/handwired/hnah40rgb/info.json @@ -0,0 +1,100 @@ +{ + "keyboard_name": "Hnah40", + "url": "", + "maintainer": "HnahKB", + "width": 12, + "height": 4, + "layouts": { + "LAYOUT_all": { + "key_count": 42, + "layout": [ + {"label":"Esc", "x":0, "y":0}, + {"label":"Q", "x":1, "y":0}, + {"label":"W", "x":2, "y":0}, + {"label":"E", "x":3, "y":0}, + {"label":"R", "x":4, "y":0}, + {"label":"T", "x":5, "y":0}, + {"label":"Y", "x":6, "y":0}, + {"label":"U", "x":7, "y":0}, + {"label":"I", "x":8, "y":0}, + {"label":"O", "x":9, "y":0}, + {"label":"P", "x":10, "y":0}, + {"label":"BSPC", "x":11, "y":0}, + {"label":"Caps Lock", "x":0, "y":1, "w":1.5}, + {"label":"A", "x":1.5, "y":1}, + {"label":"S", "x":2.5, "y":1}, + {"label":"D", "x":3.5, "y":1}, + {"label":"F", "x":4.5, "y":1}, + {"label":"G", "x":5.5, "y":1}, + {"label":"H", "x":6.5, "y":1}, + {"label":"J", "x":7.5, "y":1}, + {"label":"K", "x":8.5, "y":1}, + {"label":"L", "x":9.5, "y":1}, + {"label":"Enter", "x":10.5, "y":1, "w":1.5}, + {"label":"Shift", "x":0, "y":2, "w":1.75}, + {"label":"Z", "x":1.75, "y":2}, + {"label":"X", "x":2.75, "y":2}, + {"label":"C", "x":3.75, "y":2}, + {"label":"V", "x":4.75, "y":2}, + {"label":"B", "x":5.75, "y":2}, + {"label":"N", "x":6.75, "y":2}, + {"label":"M", "x":7.75, "y":2}, + {"label":",", "x":8.75, "y":2}, + {"label":".", "x":9.75, "y":2}, + {"label":"Shift", "x":10.75, "y":2, "w":1.25}, + {"label":"Ctrl", "x":0, "y":3, "w":1.25}, + {"label":"Win", "x":1.25, "y":3, "w":1}, + {"label":"Alt", "x":2.25, "y":3, "w":1.25}, + {"label":"Space", "x":3.5, "y":3, "w":2.25}, + {"label":"Space", "x":5.75, "y":3, "w":2.75}, + {"label":"App", "x":8.5, "y":3, "w":1.25}, + {"label":"Fn", "x":9.75, "y":3, "w":1}, + {"label":"Ctrl", "x":10.75, "y":3, "w":1.25} + ] + }, + "LAYOUT_ansi": { + "key_count": 39, + "layout": [ + {"label":"Esc", "x":0, "y":0}, + {"label":"Q", "x":1, "y":0}, + {"label":"W", "x":2, "y":0}, + {"label":"E", "x":3, "y":0}, + {"label":"R", "x":4, "y":0}, + {"label":"T", "x":5, "y":0}, + {"label":"Y", "x":6, "y":0}, + {"label":"U", "x":7, "y":0}, + {"label":"I", "x":8, "y":0}, + {"label":"O", "x":9, "y":0}, + {"label":"P", "x":10, "y":0}, + {"label":"BSPC", "x":11, "y":0}, + {"label":"Caps Lock", "x":0, "y":1, "w":1.5}, + {"label":"A", "x":1.5, "y":1}, + {"label":"S", "x":2.5, "y":1}, + {"label":"D", "x":3.5, "y":1}, + {"label":"F", "x":4.5, "y":1}, + {"label":"G", "x":5.5, "y":1}, + {"label":"H", "x":6.5, "y":1}, + {"label":"J", "x":7.5, "y":1}, + {"label":"K", "x":8.5, "y":1}, + {"label":"L", "x":9.5, "y":1}, + {"label":"Enter", "x":10.5, "y":1, "w":1.5}, + {"label":"Shift", "x":0, "y":2, "w":1.75}, + {"label":"Z", "x":1.75, "y":2}, + {"label":"X", "x":2.75, "y":2}, + {"label":"C", "x":3.75, "y":2}, + {"label":"V", "x":4.75, "y":2}, + {"label":"B", "x":5.75, "y":2}, + {"label":"N", "x":6.75, "y":2}, + {"label":"M", "x":7.75, "y":2}, + {"label":",", "x":8.75, "y":2}, + {"label":"Shift", "x":9.75, "y":2, "w":2.25}, + {"label":"Ctrl", "x":0, "y":3, "w":1.25}, + {"label":"Win", "x":1.25, "y":3}, + {"label":"Alt", "x":2.25, "y":3, "w":1.25}, + {"label":"Space", "x":3.5, "y":3, "w":6}, + {"label":"App", "x":9.5, "y":3, "w":1.25}, + {"label":"Ctrl", "x":10.75, "y":3, "w":1.25} + ] + } + } +} diff --git a/keyboards/handwired/hnah40rgb/keymaps/ansi/config.h b/keyboards/handwired/hnah40rgb/keymaps/ansi/config.h new file mode 100644 index 0000000000..66cd76a901 --- /dev/null +++ b/keyboards/handwired/hnah40rgb/keymaps/ansi/config.h @@ -0,0 +1,18 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once +#define ansi
\ No newline at end of file diff --git a/keyboards/handwired/hnah40rgb/keymaps/ansi/keymap.c b/keyboards/handwired/hnah40rgb/keymaps/ansi/keymap.c new file mode 100644 index 0000000000..320f7d93e4 --- /dev/null +++ b/keyboards/handwired/hnah40rgb/keymaps/ansi/keymap.c @@ -0,0 +1,67 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +enum hnah_layers{ + _BASE, + _L1, + _L2 +}; + +enum hnah_keycodes{ + BASE, + L1, + L2 +}; + +#define L1 MO(_L1) +#define L2 MO(_L2) + +// Defines the keycodes used by our macros in process_record_user + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_BASE] = LAYOUT_ansi(/* Base */ + KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + LT(_L2,KC_CAPS), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_RSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPACE, L1, KC_RCTL ), + [_L1] = LAYOUT_ansi(/* Base */ + RESET, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, + KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_SCLN, KC_QUOT, + KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS ), + [_L2] = LAYOUT_ansi(/* Base */ + RGB_TOG, RGB_RMOD, KC_UP, RGB_MOD, RGB_HUI, RGB_VAI, RGB_SAI, RGB_SPI, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, RGB_HUD, RGB_VAD, RGB_SAD, RGB_SPD, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TAB, KC_TRNS, KC_TRNS ), +}; + +void rgb_matrix_indicators_user(void) +{ + if (IS_HOST_LED_ON(USB_LED_CAPS_LOCK)) + { + rgb_matrix_set_color(22, 255, 255, 255); + } + if (IS_LAYER_ON(_L1)) + { + rgb_matrix_set_color(46, 255, 255, 255); + } + if (IS_LAYER_ON(_L2)) + { + rgb_matrix_set_color(45, 255, 255, 255); + } +}
\ No newline at end of file diff --git a/keyboards/handwired/hnah40rgb/keymaps/ansi/readme.md b/keyboards/handwired/hnah40rgb/keymaps/ansi/readme.md new file mode 100644 index 0000000000..825a57ab07 --- /dev/null +++ b/keyboards/handwired/hnah40rgb/keymaps/ansi/readme.md @@ -0,0 +1 @@ +# The ansi keymap for hnah40rgb
\ No newline at end of file diff --git a/keyboards/handwired/hnah40rgb/keymaps/default/config.h b/keyboards/handwired/hnah40rgb/keymaps/default/config.h new file mode 100644 index 0000000000..aa9325a59d --- /dev/null +++ b/keyboards/handwired/hnah40rgb/keymaps/default/config.h @@ -0,0 +1,17 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once diff --git a/keyboards/handwired/hnah40rgb/keymaps/default/keymap.c b/keyboards/handwired/hnah40rgb/keymaps/default/keymap.c new file mode 100644 index 0000000000..2906f8bdbf --- /dev/null +++ b/keyboards/handwired/hnah40rgb/keymaps/default/keymap.c @@ -0,0 +1,67 @@ +/* Copyright 2019 HnahKB + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +enum hnah_layers{ + _BASE, + _L1, + _L2 +}; + +enum hnah_keycodes{ + BASE, + L1, + L2 +}; + +#define L1 MO(_L1) +#define L2 MO(_L2) + +// Defines the keycodes used by our macros in process_record_user + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_BASE] = LAYOUT_all(/* Base */ + KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + LT(_L2,KC_CAPS), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPACE, KC_SPACE, KC_RALT, L1, KC_RCTL ), + [_L1] = LAYOUT_all(/* Base */ + RESET, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, + KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_SCLN, KC_QUOT, + KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_TRNS, KC_SLSH, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS ), + [_L2] = LAYOUT_all(/* Base */ + RGB_TOG, RGB_RMOD, KC_UP, RGB_MOD, RGB_HUI, RGB_VAI, RGB_SAI, RGB_SPI, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, RGB_HUD, RGB_VAD, RGB_SAD, RGB_SPD, KC_TRNS, KC_TRNS, KC_BSLS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TAB, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS ), +}; + +void rgb_matrix_indicators_user(void) +{ + if (IS_HOST_LED_ON(USB_LED_CAPS_LOCK)) + { + rgb_matrix_set_color(22, 255, 255, 255); + } + if (IS_LAYER_ON(_L1)) + { + rgb_matrix_set_color(46, 255, 255, 255); + } + if (IS_LAYER_ON(_L2)) + { + rgb_matrix_set_color(45, 255, 255, 255); + } +}
\ No newline at end of file diff --git a/keyboards/handwired/hnah40rgb/keymaps/default/readme.md b/keyboards/handwired/hnah40rgb/keymaps/default/readme.md new file mode 100644 index 0000000000..866686644d --- /dev/null +++ b/keyboards/handwired/hnah40rgb/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for hnah40rgb
\ No newline at end of file diff --git a/keyboards/handwired/hnah40rgb/readme.md b/keyboards/handwired/hnah40rgb/readme.md new file mode 100644 index 0000000000..80876f8da2 --- /dev/null +++ b/keyboards/handwired/hnah40rgb/readme.md @@ -0,0 +1,14 @@ +# hnah40rgb + + + +A 40 percent keyboard Hnah40v2 rgb version + +Keyboard Maintainer: [HnahKB](https://github.com/vuhopkep) +Hardware Availability: Hnah40V2 RGB + +Make example for this keyboard (after setting up your build environment): + + make handwired/hnah40rgb:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/hnah40rgb/rules.mk b/keyboards/handwired/hnah40rgb/rules.mk new file mode 100644 index 0000000000..5ad9f40c30 --- /dev/null +++ b/keyboards/handwired/hnah40rgb/rules.mk @@ -0,0 +1,33 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32A bootloadHID +BOOTLOADER = atmel-dfu + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration +MOUSEKEY_ENABLE = no # Mouse keys +EXTRAKEY_ENABLE = no # Audio control and System control +CONSOLE_ENABLE = no # Console for debug +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs +RGB_MATRIX_ENABLE = WS2812
\ No newline at end of file diff --git a/keyboards/handwired/ibm122m/rules.mk b/keyboards/handwired/ibm122m/rules.mk index ba4be67667..f775fa03b3 100644 --- a/keyboards/handwired/ibm122m/rules.mk +++ b/keyboards/handwired/ibm122m/rules.mk @@ -1,51 +1,15 @@ # MCU name MCU = at90usb1286 -BOOTLOADER = halfKay - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable diff --git a/keyboards/handwired/jn68m/rules.mk b/keyboards/handwired/jn68m/rules.mk index 42d85ada17..80b59d628d 100644 --- a/keyboards/handwired/jn68m/rules.mk +++ b/keyboards/handwired/jn68m/rules.mk @@ -1,64 +1,16 @@ # MCU name -#MCU = at90usb1286 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/handwired/jopr/rules.mk b/keyboards/handwired/jopr/rules.mk index de83252c38..ae10be0d26 100644 --- a/keyboards/handwired/jopr/rules.mk +++ b/keyboards/handwired/jopr/rules.mk @@ -1,52 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options # comment out to disable the options. # diff --git a/keyboards/handwired/jot50/keymaps/default/keymap.c b/keyboards/handwired/jot50/keymaps/default/keymap.c index 4ec535c31d..7342dcd22e 100644 --- a/keyboards/handwired/jot50/keymaps/default/keymap.c +++ b/keyboards/handwired/jot50/keymaps/default/keymap.c @@ -3,7 +3,6 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. @@ -81,4 +80,3 @@ uint32_t layer_state_set_user(uint32_t state) { void matrix_init_user(void) { } - diff --git a/keyboards/handwired/jot50/rules.mk b/keyboards/handwired/jot50/rules.mk index 36a100c963..d01dfefa5e 100644 --- a/keyboards/handwired/jot50/rules.mk +++ b/keyboards/handwired/jot50/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/handwired/jotanck/keymaps/default/keymap.c b/keyboards/handwired/jotanck/keymaps/default/keymap.c index 3eb01a6581..2467559a60 100644 --- a/keyboards/handwired/jotanck/keymaps/default/keymap.c +++ b/keyboards/handwired/jotanck/keymaps/default/keymap.c @@ -3,7 +3,6 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. @@ -13,11 +12,14 @@ extern keymap_config_t keymap_config; #define _QWERTY 0 #define _LOWER 1 #define _RAISE 2 -#define _ADJUST 3 #define LOWER MO(_LOWER) #define RAISE MO(_RAISE) +static bool is_ctl_pressed; +static bool is_esc_pressed; +static bool is_bspc_pressed; + const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { /* Qwerty @@ -73,20 +75,46 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_HOME, KC_PGDN, KC_PGUP, KC_END ), - -/* Adjust */ -[_ADJUST] = LAYOUT_ortho_4x12 ( - _______, RESET, _______, _______, _______, _______, _______, _______, KC_PSCR, KC_SLCK, KC_PAUS, _______, - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______ -), + }; uint32_t layer_state_set_user(uint32_t state) { - return update_tri_layer_state(state, _LOWER, _RAISE, _ADJUST); + #ifdef JOTANCK_LEDS + switch (biton32(state)) { + case _LOWER: + writePinHigh(JOTANCK_LED1); + writePinLow(JOTANCK_LED2); + break; + case _RAISE: + writePinLow(JOTANCK_LED1); + writePinHigh(JOTANCK_LED2); + break; + default: + writePinLow(JOTANCK_LED1); + writePinLow(JOTANCK_LED2); + break; + }; + #endif + return state; } -void matrix_init_user(void) { +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case KC_LCTL: + is_ctl_pressed = record->event.pressed; + break; + case KC_ESC: + is_esc_pressed = record->event.pressed; + break; + case KC_BSPC: + is_bspc_pressed = record->event.pressed; + break; + }; + return true; } +void matrix_scan_user(void) { + if (is_ctl_pressed && is_esc_pressed && is_bspc_pressed) { + reset_keyboard(); + } +} diff --git a/keyboards/handwired/jotanck/readme.md b/keyboards/handwired/jotanck/readme.md index e9dd824030..3ceea1ef4c 100644 --- a/keyboards/handwired/jotanck/readme.md +++ b/keyboards/handwired/jotanck/readme.md @@ -35,4 +35,6 @@ Make example for this keyboard (after setting up your build environment):  +To reset the keyboard press Ctrl+Esc+BackSpace + See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/jotanck/rules.mk b/keyboards/handwired/jotanck/rules.mk index fa28814133..2a233cccd0 100644 --- a/keyboards/handwired/jotanck/rules.mk +++ b/keyboards/handwired/jotanck/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/handwired/jotpad16/keymaps/default/keymap.c b/keyboards/handwired/jotpad16/keymaps/default/keymap.c index fb5dc71e23..a5d81ab3f4 100644 --- a/keyboards/handwired/jotpad16/keymaps/default/keymap.c +++ b/keyboards/handwired/jotpad16/keymaps/default/keymap.c @@ -3,7 +3,6 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. diff --git a/keyboards/handwired/jotpad16/rules.mk b/keyboards/handwired/jotpad16/rules.mk index 8105f800cb..0c9370f1c1 100644 --- a/keyboards/handwired/jotpad16/rules.mk +++ b/keyboards/handwired/jotpad16/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/handwired/kbod/keymaps/default/keymap.c b/keyboards/handwired/kbod/keymaps/default/keymap.c index 49083820ad..3119784e26 100644 --- a/keyboards/handwired/kbod/keymaps/default/keymap.c +++ b/keyboards/handwired/kbod/keymaps/default/keymap.c @@ -75,11 +75,6 @@ bool process_record_user(uint16_t keycode, keyrecord_t *record) { } } -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - return MACRO_NONE; -}; - void led_set_user(uint8_t usb_led) { if (usb_led & _BV(USB_LED_CAPS_LOCK)) { PORTB |= _BV(PB0); diff --git a/keyboards/handwired/kbod/rules.mk b/keyboards/handwired/kbod/rules.mk index b97cacd5c3..0c84098633 100644 --- a/keyboards/handwired/kbod/rules.mk +++ b/keyboards/handwired/kbod/rules.mk @@ -1,52 +1,15 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change yes to no to disable diff --git a/keyboards/handwired/lovelive9/rules.mk b/keyboards/handwired/lovelive9/rules.mk index 99a531a638..4799b5ec92 100644 --- a/keyboards/handwired/lovelive9/rules.mk +++ b/keyboards/handwired/lovelive9/rules.mk @@ -1,49 +1,14 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina # Build Options diff --git a/keyboards/handwired/maartenwut/rules.mk b/keyboards/handwired/maartenwut/rules.mk index 7ed63c65ec..5f50d6b52a 100755 --- a/keyboards/handwired/maartenwut/rules.mk +++ b/keyboards/handwired/maartenwut/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # change yes to no to disable diff --git a/keyboards/handwired/magicforce61/rules.mk b/keyboards/handwired/magicforce61/rules.mk index 91147ab4fb..d1ed63f65b 100644 --- a/keyboards/handwired/magicforce61/rules.mk +++ b/keyboards/handwired/magicforce61/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = at90usb1286 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=1024 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable diff --git a/keyboards/handwired/magicforce68/rules.mk b/keyboards/handwired/magicforce68/rules.mk index fe01b544c8..3989329835 100644 --- a/keyboards/handwired/magicforce68/rules.mk +++ b/keyboards/handwired/magicforce68/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change yes to no to disable diff --git a/keyboards/handwired/mechboards_micropad/rules.mk b/keyboards/handwired/mechboards_micropad/rules.mk index 8ac2297e46..a61b3b3d83 100644 --- a/keyboards/handwired/mechboards_micropad/rules.mk +++ b/keyboards/handwired/mechboards_micropad/rules.mk @@ -1,64 +1,16 @@ # MCU name -#MCU = at90usb1286 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/handwired/minorca/keymaps/default/keymap.c b/keyboards/handwired/minorca/keymaps/default/keymap.c index 29ed7aa03f..f8f9061fec 100644 --- a/keyboards/handwired/minorca/keymaps/default/keymap.c +++ b/keyboards/handwired/minorca/keymaps/default/keymap.c @@ -1,6 +1,5 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. diff --git a/keyboards/handwired/minorca/rules.mk b/keyboards/handwired/minorca/rules.mk index 3e408e2b93..5c29c0c93e 100644 --- a/keyboards/handwired/minorca/rules.mk +++ b/keyboards/handwired/minorca/rules.mk @@ -1,50 +1,15 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change to "no" to disable the options, or define them in the Makefile in @@ -64,4 +29,4 @@ BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
\ No newline at end of file +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend diff --git a/keyboards/handwired/ms_sculpt_mobile/rules.mk b/keyboards/handwired/ms_sculpt_mobile/rules.mk index 680c057d36..d38138bbb8 100644 --- a/keyboards/handwired/ms_sculpt_mobile/rules.mk +++ b/keyboards/handwired/ms_sculpt_mobile/rules.mk @@ -1,37 +1,27 @@ - -## Project specific files -SRC= babblePaste.c - - ifdef ASTAR - CFLAGS=-D ASTAR - MCU = atmega32u4 - SCULPT_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done ; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) - + MCU = atmega32u4 + CFLAGS = -D ASTAR + USB = /dev/cu.usbmodem14141 + SCULPT_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done ; avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) else - MCU = at90usb1286 - SCULPT_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex + MCU = at90usb1286 + SCULPT_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex endif -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp ifdef ASTAR - BOOTLOADER = caterina + BOOTLOADER = caterina else - BOOTLOADER = atmel-dfu + BOOTLOADER = atmel-dfu endif -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = no # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) @@ -47,10 +37,5 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 - -USB = /dev/cu.usbmodem14141 - - - -# upload: build -# $(SCULPT_UPLOAD_COMMAND) +# Project specific files +SRC = babblePaste.c diff --git a/keyboards/handwired/nicekey/rules.mk b/keyboards/handwired/nicekey/rules.mk index cfa693a73b..61c1fa79aa 100644 --- a/keyboards/handwired/nicekey/rules.mk +++ b/keyboards/handwired/nicekey/rules.mk @@ -1,53 +1,15 @@ - - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # comment out to disable the options. @@ -58,4 +20,4 @@ EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = yes # Console for debug(+400) COMMAND_ENABLE = yes # Commands for debug and configuration #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
\ No newline at end of file +#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA diff --git a/keyboards/handwired/not_so_minidox/keymaps/default/keymap.c b/keyboards/handwired/not_so_minidox/keymaps/default/keymap.c index 9e89611631..296a7a281d 100644 --- a/keyboards/handwired/not_so_minidox/keymaps/default/keymap.c +++ b/keyboards/handwired/not_so_minidox/keymaps/default/keymap.c @@ -1,6 +1,5 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. diff --git a/keyboards/handwired/not_so_minidox/rules.mk b/keyboards/handwired/not_so_minidox/rules.mk index 833dd4b79e..ae5cb83b7b 100644 --- a/keyboards/handwired/not_so_minidox/rules.mk +++ b/keyboards/handwired/not_so_minidox/rules.mk @@ -1,53 +1,16 @@ -SRC += matrix.c \ - i2c.c \ - split_util.c \ - serial.c - # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -69,3 +32,7 @@ USE_I2C ?= no SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend CUSTOM_MATRIX = yes +SRC += matrix.c \ + i2c.c \ + split_util.c \ + serial.c diff --git a/keyboards/handwired/numbrero/readme.md b/keyboards/handwired/numbrero/readme.md index 42f005dbe2..931c601274 100644 --- a/keyboards/handwired/numbrero/readme.md +++ b/keyboards/handwired/numbrero/readme.md @@ -8,6 +8,6 @@ Hardware Availability: The Board Podcast Slack Make example for this keyboard (after setting up your build environment): - make handwired/numbrero/numbrero:default + make handwired/numbrero:default See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/numbrero/rules.mk b/keyboards/handwired/numbrero/rules.mk index bda6c866e2..969dd0b507 100644 --- a/keyboards/handwired/numbrero/rules.mk +++ b/keyboards/handwired/numbrero/rules.mk @@ -1,49 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -#Bootloder -#Pro Micro = caterina +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Boot Section Size in *bytes* -#OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # comment out to disable the options. # diff --git a/keyboards/handwired/numpad20/rules.mk b/keyboards/handwired/numpad20/rules.mk index 361b2e93af..b5e96d74bf 100644 --- a/keyboards/handwired/numpad20/rules.mk +++ b/keyboards/handwired/numpad20/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable @@ -64,4 +27,4 @@ BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by d MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6
\ No newline at end of file +AUDIO_ENABLE = no # Audio output on port C6 diff --git a/keyboards/handwired/onekey/bluepill/config.h b/keyboards/handwired/onekey/bluepill/config.h index 3d88ee00e5..01555e4315 100644 --- a/keyboards/handwired/onekey/bluepill/config.h +++ b/keyboards/handwired/onekey/bluepill/config.h @@ -21,3 +21,9 @@ #define MATRIX_COL_PINS { B0 } #define MATRIX_ROW_PINS { A7 } #define UNUSED_PINS + +#define BACKLIGHT_PIN A0 +#define BACKLIGHT_PWM_DRIVER PWMD2 +#define BACKLIGHT_PWM_CHANNEL 1 + +#define RGB_DI_PIN A1 diff --git a/keyboards/handwired/onekey/bluepill/halconf.h b/keyboards/handwired/onekey/bluepill/halconf.h index 72879a575b..53b2f91e33 100644 --- a/keyboards/handwired/onekey/bluepill/halconf.h +++ b/keyboards/handwired/onekey/bluepill/halconf.h @@ -146,7 +146,7 @@ * @brief Enables the SPI subsystem. */ #if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) -#define HAL_USE_SPI TRUE +#define HAL_USE_SPI FALSE #endif /** diff --git a/keyboards/handwired/onekey/bluepill/mcuconf.h b/keyboards/handwired/onekey/bluepill/mcuconf.h index fced27289e..a645d3c5d5 100644 --- a/keyboards/handwired/onekey/bluepill/mcuconf.h +++ b/keyboards/handwired/onekey/bluepill/mcuconf.h @@ -132,8 +132,8 @@ * PWM driver system settings. */ #define STM32_PWM_USE_ADVANCED FALSE -#define STM32_PWM_USE_TIM1 TRUE -#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 TRUE #define STM32_PWM_USE_TIM3 FALSE #define STM32_PWM_USE_TIM4 FALSE #define STM32_PWM_USE_TIM5 FALSE @@ -168,7 +168,7 @@ * SPI driver system settings. */ #define STM32_SPI_USE_SPI1 FALSE -#define STM32_SPI_USE_SPI2 TRUE +#define STM32_SPI_USE_SPI2 FALSE #define STM32_SPI_USE_SPI3 FALSE #define STM32_SPI_SPI1_DMA_PRIORITY 1 #define STM32_SPI_SPI2_DMA_PRIORITY 1 diff --git a/keyboards/handwired/onekey/bluepill/rules.mk b/keyboards/handwired/onekey/bluepill/rules.mk index 46274066dd..aeda2782b9 100644 --- a/keyboards/handwired/onekey/bluepill/rules.mk +++ b/keyboards/handwired/onekey/bluepill/rules.mk @@ -1,7 +1,11 @@ # GENERIC STM32F103C8T6 board - stm32duino bootloader +BOARD = GENERIC_STM32_F103 + OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000 MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader -BOARD = GENERIC_STM32_F103 + +DFU_ARGS = -d 1eaf:0003 -a2 -R +DFU_SUFFIX_ARGS ?= -v 1eaf -p 0003 # OPT_DEFS = # MCU_LDSCRIPT = STM32F103x8 diff --git a/keyboards/handwired/onekey/config.h b/keyboards/handwired/onekey/config.h index 6f7ec1289f..64a447481d 100644 --- a/keyboards/handwired/onekey/config.h +++ b/keyboards/handwired/onekey/config.h @@ -35,6 +35,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* Set 0 if debouncing isn't needed */ #define DEBOUNCE 5 +#define TAPPING_TERM 500 + /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE /* Locking resynchronize hack */ diff --git a/keyboards/handwired/onekey/elite_c/rules.mk b/keyboards/handwired/onekey/elite_c/rules.mk index eb7c443951..2f20507d4d 100644 --- a/keyboards/handwired/onekey/elite_c/rules.mk +++ b/keyboards/handwired/onekey/elite_c/rules.mk @@ -1,58 +1,12 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/onekey/keymaps/backlight/config.h b/keyboards/handwired/onekey/keymaps/backlight/config.h new file mode 100644 index 0000000000..af01528b43 --- /dev/null +++ b/keyboards/handwired/onekey/keymaps/backlight/config.h @@ -0,0 +1,3 @@ +#pragma once + +#define BACKLIGHT_BREATHING diff --git a/keyboards/handwired/onekey/keymaps/backlight/keymap.c b/keyboards/handwired/onekey/keymaps/backlight/keymap.c new file mode 100644 index 0000000000..1f4be16a62 --- /dev/null +++ b/keyboards/handwired/onekey/keymaps/backlight/keymap.c @@ -0,0 +1,40 @@ +#include QMK_KEYBOARD_H + +//Tap Dance Declarations +enum { + TD_BL = 0 +}; + +void dance_cln_finished (qk_tap_dance_state_t *state, void *user_data) { + // noop +} + +void dance_cln_reset (qk_tap_dance_state_t *state, void *user_data) { + switch (state->count) { + case 1: + // single tap - step through backlight + backlight_step(); + break; +#ifdef BACKLIGHT_BREATHING + case 2: + // double tap - toggle breathing + breathing_toggle(); + break; + case 3: + //tripple tap - do some pulse stuff + breathing_pulse(); + break; +#endif + default: + // more - nothing + break; + } +} + +qk_tap_dance_action_t tap_dance_actions[] = { + [TD_BL] = ACTION_TAP_DANCE_FN_ADVANCED (NULL, dance_cln_finished, dance_cln_reset) +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + LAYOUT( TD(TD_BL) ) +}; diff --git a/keyboards/handwired/onekey/keymaps/backlight/rules.mk b/keyboards/handwired/onekey/keymaps/backlight/rules.mk new file mode 100644 index 0000000000..176e099770 --- /dev/null +++ b/keyboards/handwired/onekey/keymaps/backlight/rules.mk @@ -0,0 +1,2 @@ +BACKLIGHT_ENABLE = yes +TAP_DANCE_ENABLE = yes diff --git a/keyboards/handwired/onekey/keymaps/rgb/config.h b/keyboards/handwired/onekey/keymaps/rgb/config.h new file mode 100644 index 0000000000..89e76326b4 --- /dev/null +++ b/keyboards/handwired/onekey/keymaps/rgb/config.h @@ -0,0 +1,4 @@ +#pragma once + +#define RGBLED_NUM 9 +#define RGBLIGHT_ANIMATIONS diff --git a/keyboards/handwired/onekey/keymaps/rgb/keymap.c b/keyboards/handwired/onekey/keymaps/rgb/keymap.c new file mode 100644 index 0000000000..a96c6f3863 --- /dev/null +++ b/keyboards/handwired/onekey/keymaps/rgb/keymap.c @@ -0,0 +1,11 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + LAYOUT( RGB_MOD ) +}; + +void keyboard_post_init_user(void) { + rgblight_enable_noeeprom(); + rgblight_sethsv_noeeprom_cyan(); + rgblight_mode_noeeprom(RGBLIGHT_MODE_RAINBOW_SWIRL); +} diff --git a/keyboards/handwired/onekey/keymaps/rgb/rules.mk b/keyboards/handwired/onekey/keymaps/rgb/rules.mk new file mode 100644 index 0000000000..1e3cebb145 --- /dev/null +++ b/keyboards/handwired/onekey/keymaps/rgb/rules.mk @@ -0,0 +1 @@ +RGBLIGHT_ENABLE = yes diff --git a/keyboards/handwired/onekey/promicro/rules.mk b/keyboards/handwired/onekey/promicro/rules.mk index dc6f196237..e6fef51727 100644 --- a/keyboards/handwired/onekey/promicro/rules.mk +++ b/keyboards/handwired/onekey/promicro/rules.mk @@ -1,58 +1,12 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/onekey/proton_c/config.h b/keyboards/handwired/onekey/proton_c/config.h index f6bedcfe64..fe34f94add 100644 --- a/keyboards/handwired/onekey/proton_c/config.h +++ b/keyboards/handwired/onekey/proton_c/config.h @@ -21,3 +21,10 @@ #define MATRIX_COL_PINS { A3 } #define MATRIX_ROW_PINS { A2 } #define UNUSED_PINS + +#define BACKLIGHT_PIN B8 +#define BACKLIGHT_PWM_DRIVER PWMD4 +#define BACKLIGHT_PWM_CHANNEL 3 +#define BACKLIGHT_PAL_MODE 2 + +#define RGB_DI_PIN A1 diff --git a/keyboards/handwired/onekey/pytest/config.h b/keyboards/handwired/onekey/pytest/config.h new file mode 100644 index 0000000000..f6bedcfe64 --- /dev/null +++ b/keyboards/handwired/onekey/pytest/config.h @@ -0,0 +1,23 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { A3 } +#define MATRIX_ROW_PINS { A2 } +#define UNUSED_PINS diff --git a/keyboards/handwired/onekey/pytest/readme.md b/keyboards/handwired/onekey/pytest/readme.md new file mode 100644 index 0000000000..dbbd991f1c --- /dev/null +++ b/keyboards/handwired/onekey/pytest/readme.md @@ -0,0 +1,3 @@ +# PyTest onekey + +This is used by the python test framework. It's probably not useful otherwise. diff --git a/keyboards/handwired/onekey/pytest/rules.mk b/keyboards/handwired/onekey/pytest/rules.mk new file mode 100644 index 0000000000..b17a3d0316 --- /dev/null +++ b/keyboards/handwired/onekey/pytest/rules.mk @@ -0,0 +1,2 @@ +# MCU name +MCU = STM32F303 diff --git a/keyboards/handwired/onekey/pytest/templates/keymap.c b/keyboards/handwired/onekey/pytest/templates/keymap.c new file mode 100644 index 0000000000..d355210c47 --- /dev/null +++ b/keyboards/handwired/onekey/pytest/templates/keymap.c @@ -0,0 +1 @@ +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {__KEYMAP_GOES_HERE__}; diff --git a/keyboards/handwired/onekey/stm32f0_disco/chconf.h b/keyboards/handwired/onekey/stm32f0_disco/chconf.h new file mode 100644 index 0000000000..99fa8ce398 --- /dev/null +++ b/keyboards/handwired/onekey/stm32f0_disco/chconf.h @@ -0,0 +1,524 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 10000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 2 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 0 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/* Use __WFI in the idle thread for waiting. Does lower the power + * consumption. */ +#define CORTEX_ENABLE_WFI_IDLE TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM FALSE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT FALSE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE FALSE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP FALSE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS FALSE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK FALSE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS FALSE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS FALSE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK FALSE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS FALSE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/onekey/stm32f0_disco/config.h b/keyboards/handwired/onekey/stm32f0_disco/config.h new file mode 100644 index 0000000000..637ed65d3f --- /dev/null +++ b/keyboards/handwired/onekey/stm32f0_disco/config.h @@ -0,0 +1,30 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +#define MATRIX_COL_PINS { B4 } +#define MATRIX_ROW_PINS { B5 } +#define UNUSED_PINS + +#define BACKLIGHT_PIN C8 +#define BACKLIGHT_PWM_DRIVER PWMD3 +#define BACKLIGHT_PWM_CHANNEL 3 +#define BACKLIGHT_PAL_MODE 0 + +#define RGB_DI_PIN B15 diff --git a/keyboards/handwired/onekey/stm32f0_disco/halconf.h b/keyboards/handwired/onekey/stm32f0_disco/halconf.h new file mode 100644 index 0000000000..53b2f91e33 --- /dev/null +++ b/keyboards/handwired/onekey/stm32f0_disco/halconf.h @@ -0,0 +1,353 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef _HALCONF_H_ +#define _HALCONF_H_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT FALSE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM TRUE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB FALSE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* _HALCONF_H_ */ + +/** @} */ diff --git a/keyboards/handwired/onekey/stm32f0_disco/mcuconf.h b/keyboards/handwired/onekey/stm32f0_disco/mcuconf.h new file mode 100644 index 0000000000..20c48b611a --- /dev/null +++ b/keyboards/handwired/onekey/stm32f0_disco/mcuconf.h @@ -0,0 +1,171 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _MCUCONF_H_ +#define _MCUCONF_H_ + +/* + * STM32F0xx drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 3...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +#define STM32F0xx_MCUCONF + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 +#define STM32_HSI_ENABLED TRUE +#define STM32_HSI14_ENABLED TRUE +#define STM32_HSI48_ENABLED FALSE +#define STM32_LSI_ENABLED TRUE +#define STM32_HSE_ENABLED FALSE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSI_DIV2 +#define STM32_PREDIV_VALUE 1 +#define STM32_PLLMUL_VALUE 12 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE STM32_PPRE_DIV1 +#define STM32_ADCSW STM32_ADCSW_HSI14 +#define STM32_ADCPRE STM32_ADCPRE_DIV4 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_ADCPRE STM32_ADCPRE_DIV4 +#define STM32_ADCSW STM32_ADCSW_HSI14 +#define STM32_USBSW STM32_USBSW_HSI48 +#define STM32_CECSW STM32_CECSW_HSI +#define STM32_I2C1SW STM32_I2C1SW_HSI +#define STM32_USART1SW STM32_USART1SW_PCLK +#define STM32_RTCSEL STM32_RTCSEL_LSI + +/* + * ADC driver system settings. + */ +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_IRQ_PRIORITY 2 +#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 2 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_1_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI2_3_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI4_15_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 3 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 3 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM14 FALSE +#define STM32_GPT_TIM1_IRQ_PRIORITY 2 +#define STM32_GPT_TIM2_IRQ_PRIORITY 2 +#define STM32_GPT_TIM3_IRQ_PRIORITY 2 +#define STM32_GPT_TIM14_IRQ_PRIORITY 2 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 3 +#define STM32_I2C_I2C2_IRQ_PRIORITY 3 +#define STM32_I2C_USE_DMA TRUE +#define STM32_I2C_I2C1_DMA_PRIORITY 1 +#define STM32_I2C_I2C2_DMA_PRIORITY 1 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 3 +#define STM32_ICU_TIM2_IRQ_PRIORITY 3 +#define STM32_ICU_TIM3_IRQ_PRIORITY 3 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 TRUE +#define STM32_PWM_TIM1_IRQ_PRIORITY 3 +#define STM32_PWM_TIM2_IRQ_PRIORITY 3 +#define STM32_PWM_TIM3_IRQ_PRIORITY 3 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 FALSE +#define STM32_SERIAL_USART1_PRIORITY 3 +#define STM32_SERIAL_USART2_PRIORITY 3 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 2 +#define STM32_SPI_SPI2_IRQ_PRIORITY 2 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 2 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 3 +#define STM32_UART_USART2_IRQ_PRIORITY 3 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_LP_IRQ_PRIORITY 3 + +#endif /* _MCUCONF_H_ */ diff --git a/keyboards/handwired/onekey/stm32f0_disco/readme.md b/keyboards/handwired/onekey/stm32f0_disco/readme.md new file mode 100644 index 0000000000..48d999d69c --- /dev/null +++ b/keyboards/handwired/onekey/stm32f0_disco/readme.md @@ -0,0 +1,5 @@ +# STM32F072 Discovery kit onekey + +Supported Hardware: <https://www.st.com/en/evaluation-tools/32f072bdiscovery.html> + +To trigger keypress, short together pins *B4* and *B5*. diff --git a/keyboards/handwired/onekey/stm32f0_disco/rules.mk b/keyboards/handwired/onekey/stm32f0_disco/rules.mk new file mode 100644 index 0000000000..69639f940e --- /dev/null +++ b/keyboards/handwired/onekey/stm32f0_disco/rules.mk @@ -0,0 +1,34 @@ +## chip/board settings +# the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +MCU_FAMILY = STM32 +MCU_SERIES = STM32F0xx +# linker script to use +# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +MCU_LDSCRIPT = STM32F072xB +# startup code to use +# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ +MCU_STARTUP = stm32f0xx +# it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +BOARD = ST_STM32F072B_DISCOVERY +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m0 +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +ARMV = 6 +# If you want to be able to jump to bootloader from firmware on STM32 MCUs, +# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in +# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have +# a custom board definition that you plan to reuse). +# If you're not setting it here, leave it commented out. +# It is chip dependent, the correct number can be looked up here (page 175): +# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf +# This also requires a patch to chibios: +# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch +#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800 + +# Options to pass to dfu-util when flashing +DFU_ARGS = -d 0483:df11 -a 0 -s 0x08000000:leave +DFU_SUFFIX_ARGS = -p df11 -v 0483 diff --git a/keyboards/handwired/onekey/teensy_2/rules.mk b/keyboards/handwired/onekey/teensy_2/rules.mk index 3fb7c7e5a7..ae398e2588 100644 --- a/keyboards/handwired/onekey/teensy_2/rules.mk +++ b/keyboards/handwired/onekey/teensy_2/rules.mk @@ -1,58 +1,12 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay - - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/onekey/teensy_2pp/rules.mk b/keyboards/handwired/onekey/teensy_2pp/rules.mk index e318e4b9e7..c421eb862e 100644 --- a/keyboards/handwired/onekey/teensy_2pp/rules.mk +++ b/keyboards/handwired/onekey/teensy_2pp/rules.mk @@ -1,58 +1,12 @@ # MCU name MCU = at90usb1286 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = halfkay - - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 diff --git a/keyboards/handwired/ortho5x13/rules.mk b/keyboards/handwired/ortho5x13/rules.mk index fe01b544c8..b5e96d74bf 100644 --- a/keyboards/handwired/ortho5x13/rules.mk +++ b/keyboards/handwired/ortho5x13/rules.mk @@ -1,52 +1,15 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable diff --git a/keyboards/handwired/owlet60/config.h b/keyboards/handwired/owlet60/config.h new file mode 100644 index 0000000000..29fd0b1e57 --- /dev/null +++ b/keyboards/handwired/owlet60/config.h @@ -0,0 +1,250 @@ +/* +Copyright 2019 worthlessowl + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0xDA19 +#define DEVICE_VER 0x0001 +#define MANUFACTURER worthlessowl +#define PRODUCT Owlet60 +#define DESCRIPTION TGR Alice inspired 65 or 60 percent keyboard + +/* key matrix size */ +#define MATRIX_ROWS 9 +#define MATRIX_COLS 8 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS {B5, F4, F5, F6, F7, B1, B3, B2, B6} +#define MATRIX_COL_SELECT_PINS {D7, B4, E6} +#define MATRIX_COL_DATA_PIN {C6} +#define MATRIX_COL_PINS {} + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +/* + * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN. + */ +//#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6 + +//#define BACKLIGHT_PIN D3 +//#define BACKLIGHT_BREATHING +//#define BACKLIGHT_LEVELS 3 + +#define RGB_DI_PIN D0 +#ifdef RGB_DI_PIN + #define RGBLED_NUM 8 + #define RGBLIGHT_HUE_STEP 8 + #define RGBLIGHT_SAT_STEP 8 + #define RGBLIGHT_VAL_STEP 8 + #define RGBLIGHT_LIMIT_VAL 128 /* The maximum brightness level */ + #define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ +/*== all animations enable ==*/ + #define RGBLIGHT_ANIMATIONS +// /*== or choose animations ==*/ +// #define RGBLIGHT_EFFECT_BREATHING +// #define RGBLIGHT_EFFECT_RAINBOW_MOOD +// #define RGBLIGHT_EFFECT_RAINBOW_SWIRL +// #define RGBLIGHT_EFFECT_SNAKE +// #define RGBLIGHT_EFFECT_KNIGHT +// #define RGBLIGHT_EFFECT_CHRISTMAS +// #define RGBLIGHT_EFFECT_STATIC_GRADIENT +// #define RGBLIGHT_EFFECT_RGB_TEST +// #define RGBLIGHT_EFFECT_ALTERNATING +// /*== customize breathing effect ==*/ +// /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ +// #define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 +// /*==== use exp() and sin() ====*/ +// #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 +// #define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 +#endif + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 9 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +//#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +/* defined by default; to change, uncomment and set to the combination you want */ +// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP H +//#define MAGIC_KEY_HELP_ALT SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER0_ALT GRAVE +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER B +//#define MAGIC_KEY_BOOTLOADER_ALT ESC +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_EEPROM_CLEAR BSPACE +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +/* + * HD44780 LCD Display Configuration + */ +/* +#define LCD_LINES 2 //< number of visible lines of the display +#define LCD_DISP_LENGTH 16 //< visibles characters per line of the display + +#define LCD_IO_MODE 1 //< 0: memory mapped mode, 1: IO port mode + +#if LCD_IO_MODE +#define LCD_PORT PORTB //< port for the LCD lines +#define LCD_DATA0_PORT LCD_PORT //< port for 4bit data bit 0 +#define LCD_DATA1_PORT LCD_PORT //< port for 4bit data bit 1 +#define LCD_DATA2_PORT LCD_PORT //< port for 4bit data bit 2 +#define LCD_DATA3_PORT LCD_PORT //< port for 4bit data bit 3 +#define LCD_DATA0_PIN 4 //< pin for 4bit data bit 0 +#define LCD_DATA1_PIN 5 //< pin for 4bit data bit 1 +#define LCD_DATA2_PIN 6 //< pin for 4bit data bit 2 +#define LCD_DATA3_PIN 7 //< pin for 4bit data bit 3 +#define LCD_RS_PORT LCD_PORT //< port for RS line +#define LCD_RS_PIN 3 //< pin for RS line +#define LCD_RW_PORT LCD_PORT //< port for RW line +#define LCD_RW_PIN 2 //< pin for RW line +#define LCD_E_PORT LCD_PORT //< port for Enable line +#define LCD_E_PIN 1 //< pin for Enable line +#endif +*/ + +/* Bootmagic Lite key configuration */ +// #define BOOTMAGIC_LITE_ROW 0 +// #define BOOTMAGIC_LITE_COLUMN 0 diff --git a/keyboards/handwired/owlet60/info.json b/keyboards/handwired/owlet60/info.json new file mode 100644 index 0000000000..6e5345c337 --- /dev/null +++ b/keyboards/handwired/owlet60/info.json @@ -0,0 +1,25 @@ +{ + "keyboard_name": "Owlet60", + "url": "https://github.com/qmk/qmk_firmware/tree/master/keyboards/handwired/owlet60/", + "maintainer": "worthlessowl", + "width": 19, + "height": 5, + "layouts": { + "LAYOUT_owlet60_full_bsp": { + "key_count": 71, + "layout": [{"label":"F1", "x":0.5, "y":0}, {"label":"~", "x":1.75, "y":0}, {"label":"!", "x":2.75, "y":0}, {"label":"@", "x":3.75, "y":0}, {"label":"#", "x":4.75, "y":0}, {"label":"$", "x":5.75, "y":0}, {"label":"%", "x":6.75, "y":0}, {"label":"^", "x":7.75, "y":0}, {"label":"&", "x":9.25, "y":0}, {"label":"*", "x":10.25, "y":0}, {"label":"(", "x":11.25, "y":0}, {"label":")", "x":12.25, "y":0}, {"label":"_", "x":13.25, "y":0}, {"label":"+", "x":14.25, "y":0}, {"label":"Backspace", "x":15.25, "y":0, "w":2}, {"label":"PgUp", "x":17.25, "y":0}, {"label":"F2", "x":0.25, "y":1}, {"label":"Tab", "x":1.5, "y":1, "w":1.5}, {"label":"Q", "x":3, "y":1}, {"label":"W", "x":4, "y":1}, {"label":"E", "x":5, "y":1}, {"label":"R", "x":6, "y":1}, {"label":"T", "x":7, "y":1}, {"label":"Y", "x":9, "y":1}, {"label":"U", "x":10, "y":1}, {"label":"I", "x":11, "y":1}, {"label":"O", "x":12, "y":1}, {"label":"P", "x":13, "y":1}, {"label":"{", "x":14, "y":1}, {"label":"}", "x":15, "y":1}, {"label":"|", "x":16, "y":1, "w":1.5}, {"label":"PgDn", "x":17.5, "y":1}, {"label":"F3", "x":0, "y":2}, {"label":"Caps Lock", "x":1.25, "y":2, "w":1.75}, {"label":"A", "x":3, "y":2}, {"label":"S", "x":4, "y":2}, {"label":"D", "x":5, "y":2}, {"label":"F", "x":6, "y":2}, {"label":"G", "x":7, "y":2}, {"label":"H", "x":9.5, "y":2}, {"label":"J", "x":10.5, "y":2}, {"label":"K", "x":11.5, "y":2}, {"label":"L", "x":12.5, "y":2}, {"label":":", "x":13.5, "y":2}, {"label":"\"", "x":14.5, "y":2}, {"label":"Enter", "x":15.5, "y":2, "w":2.25}, {"label":"Home", "x":17.75, "y":2}, {"label":"Shift", "x":1, "y":3, "w":2.25}, {"label":"Z", "x":3.25, "y":3}, {"label":"X", "x":4.25, "y":3}, {"label":"C", "x":5.25, "y":3}, {"label":"V", "x":6.25, "y":3}, {"label":"B", "x":7.25, "y":3}, {"label":"B", "x":9.25, "y":3}, {"label":"N", "x":10.25, "y":3}, {"label":"M", "x":11.25, "y":3}, {"label":"<", "x":12.25, "y":3}, {"label":">", "x":13.25, "y":3}, {"label":"?", "x":14.25, "y":3}, {"label":"Shift", "x":15.25, "y":3, "w":1.75}, {"label":"Up", "x":17, "y":3}, {"label":"End", "x":18, "y":3}, {"label":"Ctrl", "x":1, "y":4, "w":1.5}, {"label":"Alt", "x":3.5, "y":4, "w":1.5}, {"x":5, "y":4, "w":2.25}, {"label":"Super", "x":7.25, "y":4, "w":1.25}, {"x":9.25, "y":4, "w":2}, {"label":"Alt", "x":11.25, "y":4, "w":1.5}, {"label":"Left", "x":16, "y":4}, {"label":"Down", "x":17, "y":4}, {"label":"Right", "x":18, "y":4}] + }, + "LAYOUT_owlet60_split_bsp": { + "key_count": 72, + "layout": [{"label":"F1", "x":0.5, "y":0}, {"label":"~", "x":1.75, "y":0}, {"label":"!", "x":2.75, "y":0}, {"label":"@", "x":3.75, "y":0}, {"label":"#", "x":4.75, "y":0}, {"label":"$", "x":5.75, "y":0}, {"label":"%", "x":6.75, "y":0}, {"label":"^", "x":7.75, "y":0}, {"label":"&", "x":9.25, "y":0}, {"label":"*", "x":10.25, "y":0}, {"label":"(", "x":11.25, "y":0}, {"label":")", "x":12.25, "y":0}, {"label":"_", "x":13.25, "y":0}, {"label":"+", "x":14.25, "y":0}, {"label":"Bsp", "x":15.25, "y":0}, {"label":"Del", "x":16.25, "y":0}, {"label":"PgUp", "x":17.25, "y":0}, {"label":"F2", "x":0.25, "y":1}, {"label":"Tab", "x":1.5, "y":1, "w":1.5}, {"label":"Q", "x":3, "y":1}, {"label":"W", "x":4, "y":1}, {"label":"E", "x":5, "y":1}, {"label":"R", "x":6, "y":1}, {"label":"T", "x":7, "y":1}, {"label":"Y", "x":9, "y":1}, {"label":"U", "x":10, "y":1}, {"label":"I", "x":11, "y":1}, {"label":"O", "x":12, "y":1}, {"label":"P", "x":13, "y":1}, {"label":"{", "x":14, "y":1}, {"label":"}", "x":15, "y":1}, {"label":"|", "x":16, "y":1, "w":1.5}, {"label":"PgDn", "x":17.5, "y":1}, {"label":"F3", "x":0, "y":2}, {"label":"Caps Lock", "x":1.25, "y":2, "w":1.75}, {"label":"A", "x":3, "y":2}, {"label":"S", "x":4, "y":2}, {"label":"D", "x":5, "y":2}, {"label":"F", "x":6, "y":2}, {"label":"G", "x":7, "y":2}, {"label":"H", "x":9.5, "y":2}, {"label":"J", "x":10.5, "y":2}, {"label":"K", "x":11.5, "y":2}, {"label":"L", "x":12.5, "y":2}, {"label":":", "x":13.5, "y":2}, {"label":"\"", "x":14.5, "y":2}, {"label":"Enter", "x":15.5, "y":2, "w":2.25}, {"label":"Home", "x":17.75, "y":2}, {"label":"Shift", "x":1, "y":3, "w":2.25}, {"label":"Z", "x":3.25, "y":3}, {"label":"X", "x":4.25, "y":3}, {"label":"C", "x":5.25, "y":3}, {"label":"V", "x":6.25, "y":3}, {"label":"B", "x":7.25, "y":3}, {"label":"B", "x":9.25, "y":3}, {"label":"N", "x":10.25, "y":3}, {"label":"M", "x":11.25, "y":3}, {"label":"<", "x":12.25, "y":3}, {"label":">", "x":13.25, "y":3}, {"label":"?", "x":14.25, "y":3}, {"label":"Shift", "x":15.25, "y":3, "w":1.75}, {"label":"Up", "x":17, "y":3}, {"label":"End", "x":18, "y":3}, {"label":"Ctrl", "x":1, "y":4, "w":1.5}, {"label":"Alt", "x":3.5, "y":4, "w":1.5}, {"x":5, "y":4, "w":2.25}, {"label":"Super", "x":7.25, "y":4, "w":1.25}, {"x":9.25, "y":4, "w":2}, {"label":"Alt", "x":11.25, "y":4, "w":1.5}, {"label":"Left", "x":16, "y":4}, {"label":"Down", "x":17, "y":4}, {"label":"Right", "x":18, "y":4}] + }, + "LAYOUT_owlet60_60_percent_split_bsp": { + "key_count": 66, + "layout": [{"label":"F1", "x":0.5, "y":0}, {"label":"~", "x":1.75, "y":0}, {"label":"!", "x":2.75, "y":0}, {"label":"@", "x":3.75, "y":0}, {"label":"#", "x":4.75, "y":0}, {"label":"$", "x":5.75, "y":0}, {"label":"%", "x":6.75, "y":0}, {"label":"^", "x":7.75, "y":0}, {"label":"&", "x":9.25, "y":0}, {"label":"*", "x":10.25, "y":0}, {"label":"(", "x":11.25, "y":0}, {"label":")", "x":12.25, "y":0}, {"label":"_", "x":13.25, "y":0}, {"label":"+", "x":14.25, "y":0}, {"label":"Bsp", "x":15.25, "y":0}, {"label":"Del", "x":16.25, "y":0}, {"label":"F2", "x":0.25, "y":1}, {"label":"Tab", "x":1.5, "y":1, "w":1.5}, {"label":"Q", "x":3, "y":1}, {"label":"W", "x":4, "y":1}, {"label":"E", "x":5, "y":1}, {"label":"R", "x":6, "y":1}, {"label":"T", "x":7, "y":1}, {"label":"Y", "x":9, "y":1}, {"label":"U", "x":10, "y":1}, {"label":"I", "x":11, "y":1}, {"label":"O", "x":12, "y":1}, {"label":"P", "x":13, "y":1}, {"label":"{", "x":14, "y":1}, {"label":"}", "x":15, "y":1}, {"label":"|", "x":16, "y":1, "w":1.5}, {"label":"F3", "x":0, "y":2}, {"label":"Caps Lock", "x":1.25, "y":2, "w":1.75}, {"label":"A", "x":3, "y":2}, {"label":"S", "x":4, "y":2}, {"label":"D", "x":5, "y":2}, {"label":"F", "x":6, "y":2}, {"label":"G", "x":7, "y":2}, {"label":"H", "x":9.5, "y":2}, {"label":"J", "x":10.5, "y":2}, {"label":"K", "x":11.5, "y":2}, {"label":"L", "x":12.5, "y":2}, {"label":":", "x":13.5, "y":2}, {"label":"\"", "x":14.5, "y":2}, {"label":"Enter", "x":15.5, "y":2, "w":2.25}, {"label":"Shift", "x":1, "y":3, "w":2.25}, {"label":"Z", "x":3.25, "y":3}, {"label":"X", "x":4.25, "y":3}, {"label":"C", "x":5.25, "y":3}, {"label":"V", "x":6.25, "y":3}, {"label":"B", "x":7.25, "y":3}, {"label":"B", "x":9.25, "y":3}, {"label":"N", "x":10.25, "y":3}, {"label":"M", "x":11.25, "y":3}, {"label":"<", "x":12.25, "y":3}, {"label":">", "x":13.25, "y":3}, {"label":"?", "x":14.25, "y":3}, {"label":"Shift", "x":15.25, "y":3, "w":1.75}, {"label":"Up", "x":17, "y":3}, {"label":"Ctrl", "x":1, "y":4, "w":1.5}, {"label":"Alt", "x":3.5, "y":4, "w":1.5}, {"x":5, "y":4, "w":2.25}, {"label":"Super", "x":7.25, "y":4, "w":1.25}, {"x":9.25, "y":4, "w":2}, {"label":"Alt", "x":11.25, "y":4, "w":1.5}, {"label":"Ctrl", "x":16.25, "y":4, "w":1.5}] + }, + "LAYOUT_owlet60_60_percent_full_bsp": { + "key_count": 65, + "layout": [{"label":"F1", "x":0.5, "y":0}, {"label":"~", "x":1.75, "y":0}, {"label":"!", "x":2.75, "y":0}, {"label":"@", "x":3.75, "y":0}, {"label":"#", "x":4.75, "y":0}, {"label":"$", "x":5.75, "y":0}, {"label":"%", "x":6.75, "y":0}, {"label":"^", "x":7.75, "y":0}, {"label":"&", "x":9.25, "y":0}, {"label":"*", "x":10.25, "y":0}, {"label":"(", "x":11.25, "y":0}, {"label":")", "x":12.25, "y":0}, {"label":"_", "x":13.25, "y":0}, {"label":"+", "x":14.25, "y":0}, {"label":"Bsp", "x":15.25, "y":0, "w":2}, {"label":"F2", "x":0.25, "y":1}, {"label":"Tab", "x":1.5, "y":1, "w":1.5}, {"label":"Q", "x":3, "y":1}, {"label":"W", "x":4, "y":1}, {"label":"E", "x":5, "y":1}, {"label":"R", "x":6, "y":1}, {"label":"T", "x":7, "y":1}, {"label":"Y", "x":9, "y":1}, {"label":"U", "x":10, "y":1}, {"label":"I", "x":11, "y":1}, {"label":"O", "x":12, "y":1}, {"label":"P", "x":13, "y":1}, {"label":"{", "x":14, "y":1}, {"label":"}", "x":15, "y":1}, {"label":"|", "x":16, "y":1, "w":1.5}, {"label":"F3", "x":0, "y":2}, {"label":"Caps Lock", "x":1.25, "y":2, "w":1.75}, {"label":"A", "x":3, "y":2}, {"label":"S", "x":4, "y":2}, {"label":"D", "x":5, "y":2}, {"label":"F", "x":6, "y":2}, {"label":"G", "x":7, "y":2}, {"label":"H", "x":9.5, "y":2}, {"label":"J", "x":10.5, "y":2}, {"label":"K", "x":11.5, "y":2}, {"label":"L", "x":12.5, "y":2}, {"label":":", "x":13.5, "y":2}, {"label":"\"", "x":14.5, "y":2}, {"label":"Enter", "x":15.5, "y":2, "w":2.25}, {"label":"Shift", "x":1, "y":3, "w":2.25}, {"label":"Z", "x":3.25, "y":3}, {"label":"X", "x":4.25, "y":3}, {"label":"C", "x":5.25, "y":3}, {"label":"V", "x":6.25, "y":3}, {"label":"B", "x":7.25, "y":3}, {"label":"B", "x":9.25, "y":3}, {"label":"N", "x":10.25, "y":3}, {"label":"M", "x":11.25, "y":3}, {"label":"<", "x":12.25, "y":3}, {"label":">", "x":13.25, "y":3}, {"label":"?", "x":14.25, "y":3}, {"label":"Shift", "x":15.25, "y":3, "w":1.75}, {"label":"Up", "x":17, "y":3}, {"label":"Ctrl", "x":1, "y":4, "w":1.5}, {"label":"Alt", "x":3.5, "y":4, "w":1.5}, {"x":5, "y":4, "w":2.25}, {"label":"Super", "x":7.25, "y":4, "w":1.25}, {"x":9.25, "y":4, "w":2}, {"label":"Alt", "x":11.25, "y":4, "w":1.5}, {"label":"Ctrl", "x":16.25, "y":4, "w":1.5}] + } + } +} diff --git a/keyboards/handwired/owlet60/keymaps/default/config.h b/keyboards/handwired/owlet60/keymaps/default/config.h new file mode 100644 index 0000000000..f662fe7c93 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 worthlessowl + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/owlet60/keymaps/default/keymap.c b/keyboards/handwired/owlet60/keymaps/default/keymap.c new file mode 100644 index 0000000000..b4d0360db3 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/default/keymap.c @@ -0,0 +1,74 @@ +/* Copyright 2019 worthlessowl + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +// Defines the keycodes used by our macros in process_record_user +enum custom_keycodes { + QMKBEST = SAFE_RANGE, + QMKURL +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT_owlet60_full_bsp( + KC_1, KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_PGUP, \ + KC_2, KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_PGDOWN, \ + KC_3, KC_CAPS,KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_ENT, KC_HOME, \ + KC_LSFT,KC_Z, KC_X, KC_C, KC_V, KC_B, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_END, \ + KC_LCTRL, KC_LALT, KC_SPC, MO(1),KC_SPC, KC_RALT, KC_LEFT, KC_DOWN, KC_RIGHT \ + ), + + [1] = LAYOUT_owlet60_full_bsp( + KC_NO, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, RGB_TOG, \ + KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, RGB_MOD, \ + KC_NO, KC_NO,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,KC_NO, KC_NO, RGB_VAI, \ + KC_TRNS,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_N, KC_NO, KC_NO,KC_NO, KC_NO, KC_NO, KC_TRNS, RGB_VAD, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ) +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QMKBEST: + if (record->event.pressed) { + // when keycode QMKBEST is pressed + SEND_STRING("QMK is the best thing ever!"); + } else { + // when keycode QMKBEST is released + } + break; + case QMKURL: + if (record->event.pressed) { + // when keycode QMKURL is pressed + SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER)); + } else { + // when keycode QMKURL is released + } + break; + } + return true; +} + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/handwired/owlet60/keymaps/default/readme.md b/keyboards/handwired/owlet60/keymaps/default/readme.md new file mode 100644 index 0000000000..1d177ae102 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for owlet60
\ No newline at end of file diff --git a/keyboards/handwired/owlet60/keymaps/oled_testing/config.h b/keyboards/handwired/owlet60/keymaps/oled_testing/config.h new file mode 100644 index 0000000000..884d36b690 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/oled_testing/config.h @@ -0,0 +1,22 @@ +/* Copyright 2019 worthlessowl + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here + + +#define OLED_FONT_H "customfont.c" diff --git a/keyboards/handwired/owlet60/keymaps/oled_testing/customfont.c b/keyboards/handwired/owlet60/keymaps/oled_testing/customfont.c new file mode 100644 index 0000000000..b7ad73bfa2 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/oled_testing/customfont.c @@ -0,0 +1,20 @@ +#pragma once + +#ifdef __AVR__ +# include <avr/io.h> +# include <avr/pgmspace.h> +#elif defined(ESP8266) +# include <pgmspace.h> +#else +# define PROGMEM +#endif + +// Helidox 8x6 font with QMK Firmware Logo +// Online editor: http://teripom.x0.com/ + +static const unsigned char font[] PROGMEM = { +0x00,0x00,0x00,0x00,0x00,0x00,0x3e,0x5b,0x4f,0x5b,0x3e,0x00,0x3e,0x6b,0x4f,0x6b,0x3e,0x00,0x1c,0x3e,0x7c,0x3e,0x1c,0x00,0x18,0x3c,0x7e,0x3c,0x18,0x00,0x1c,0x57,0x7d,0x57,0x1c,0x00,0x1c,0x5e,0x7f,0x5e,0x1c,0x00,0x00,0x18,0x3c,0x18,0x00,0x00,0xff,0xe7,0xc3,0xe7,0xff,0x00,0x00,0x18,0x24,0x18,0x00,0x00,0xff,0xe7,0xdb,0xe7,0xff,0x00,0x30,0x48,0x3a,0x06,0x0e,0x00,0x26,0x29,0x79,0x29,0x26,0x00,0x40,0x7f,0x05,0x05,0x07,0x00,0x40,0x7f,0x05,0x25,0x3f,0x00,0x5a,0x3c,0xe7,0x3c,0x5a,0x00,0x7f,0x3e,0x1c,0x1c,0x08,0x00,0x08,0x1c,0x1c,0x3e,0x7f,0x00,0x14,0x22,0x7f,0x22,0x14,0x00,0x5f,0x5f,0x00,0x5f,0x5f,0x00,0x06,0x09,0x7f,0x01,0x7f,0x00,0x00,0x66,0x89,0x95,0x6a,0x00,0x60,0x60,0x60,0x60,0x60,0x00,0x94,0xa2,0xff,0xa2,0x94,0x00,0x08,0x04,0x7e,0x04,0x08,0x00,0x10,0x20,0x7e,0x20,0x10,0x00,0x08,0x08,0x2a,0x1c,0x08,0x00,0x08,0x1c,0x2a,0x08,0x08,0x00,0x1e,0x10,0x10,0x10,0x10,0x00,0x0c,0x1e,0x0c,0x1e,0x0c,0x00,0x30,0x38,0x3e,0x38,0x30,0x00,0x06,0x0e,0x3e,0x0e,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x5f,0x00,0x00,0x00,0x00,0x07,0x00,0x07,0x00,0x00,0x14,0x7f,0x14,0x7f,0x14,0x00,0x24,0x2a,0x7f,0x2a,0x12,0x00,0x23,0x13,0x08,0x64,0x62,0x00,0x36,0x49,0x56,0x20,0x50,0x00,0x00,0x08,0x07,0x03,0x00,0x00,0x00,0x1c,0x22,0x41,0x00,0x00,0x00,0x41,0x22,0x1c,0x00,0x00,0x2a,0x1c,0x7f,0x1c,0x2a,0x00,0x08,0x08,0x3e,0x08,0x08,0x00,0x00,0x80,0x70,0x30,0x00,0x00,0x08,0x08,0x08,0x08,0x08,0x00,0x00,0x00,0x60,0x60,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x00,0x3e,0x51,0x49,0x45,0x3e,0x00,0x00,0x42,0x7f,0x40,0x00,0x00,0x72,0x49,0x49,0x49,0x46,0x00,0x21,0x41,0x49,0x4d,0x33,0x00,0x18,0x14,0x12,0x7f,0x10,0x00,0x27,0x45,0x45,0x45,0x39,0x00,0x3c,0x4a,0x49,0x49,0x31,0x00,0x41,0x21,0x11,0x09,0x07,0x00,0x36,0x49,0x49,0x49,0x36,0x00,0x46,0x49,0x49,0x29,0x1e,0x00,0x00,0x00,0x14,0x00,0x00,0x00,0x00,0x40,0x34,0x00,0x00,0x00,0x00,0x08,0x14,0x22,0x41,0x00,0x14,0x14,0x14,0x14,0x14,0x00,0x00,0x41,0x22,0x14,0x08,0x00,0x02,0x01,0x59,0x09,0x06,0x00,0x3e,0x41,0x5d,0x59,0x4e,0x00,0x7c,0x12,0x11,0x12,0x7c,0x00,0x7f,0x49,0x49,0x49, +0x36,0x00,0x3e,0x41,0x41,0x41,0x22,0x00,0x7f,0x41,0x41,0x41,0x3e,0x00,0x7f,0x49,0x49,0x49,0x41,0x00,0x7f,0x09,0x09,0x09,0x01,0x00,0x3e,0x41,0x41,0x51,0x73,0x00,0x7f,0x08,0x08,0x08,0x7f,0x00,0x00,0x41,0x7f,0x41,0x00,0x00,0x20,0x40,0x41,0x3f,0x01,0x00,0x7f,0x08,0x14,0x22,0x41,0x00,0x7f,0x40,0x40,0x40,0x40,0x00,0x7f,0x02,0x1c,0x02,0x7f,0x00,0x7f,0x04,0x08,0x10,0x7f,0x00,0x3e,0x41,0x41,0x41,0x3e,0x00,0x7f,0x09,0x09,0x09,0x06,0x00,0x3e,0x41,0x51,0x21,0x5e,0x00,0x7f,0x09,0x19,0x29,0x46,0x00,0x26,0x49,0x49,0x49,0x32,0x00,0x03,0x01,0x7f,0x01,0x03,0x00,0x3f,0x40,0x40,0x40,0x3f,0x00,0x1f,0x20,0x40,0x20,0x1f,0x00,0x3f,0x40,0x38,0x40,0x3f,0x00,0x63,0x14,0x08,0x14,0x63,0x00,0x03,0x04,0x78,0x04,0x03,0x00,0x61,0x59,0x49,0x4d,0x43,0x00,0x00,0x7f,0x41,0x41,0x41,0x00,0x02,0x04,0x08,0x10,0x20,0x00,0x00,0x41,0x41,0x41,0x7f,0x00,0x04,0x02,0x01,0x02,0x04,0x00,0x40,0x40,0x40,0x40,0x40,0x00,0x00,0x03,0x07,0x08,0x00,0x00,0x20,0x54,0x54,0x78,0x40,0x00,0x7f,0x28,0x44,0x44,0x38,0x00,0x38,0x44,0x44,0x44,0x28,0x00,0x38,0x44,0x44,0x28,0x7f,0x00,0x38,0x54,0x54,0x54,0x18,0x00,0x00,0x08,0x7e,0x09,0x02,0x00,0x18,0xa4,0xa4,0x9c,0x78,0x00,0x7f,0x08,0x04,0x04,0x78,0x00,0x00,0x44,0x7d,0x40,0x00,0x00,0x20,0x40,0x40,0x3d,0x00,0x00,0x7f,0x10,0x28,0x44,0x00,0x00,0x00,0x41,0x7f,0x40,0x00,0x00,0x7c,0x04,0x78,0x04,0x78,0x00,0x7c,0x08,0x04,0x04,0x78,0x00,0x38,0x44,0x44,0x44,0x38,0x00,0xfc,0x18,0x24,0x24,0x18,0x00,0x18,0x24,0x24,0x18,0xfc,0x00,0x7c,0x08,0x04,0x04,0x08,0x00,0x48,0x54,0x54,0x54,0x24,0x00,0x04,0x04,0x3f,0x44,0x24,0x00,0x3c,0x40,0x40,0x20,0x7c,0x00,0x1c,0x20,0x40,0x20,0x1c,0x00,0x3c,0x40,0x30,0x40,0x3c,0x00,0x44,0x28,0x10,0x28,0x44,0x00,0x4c,0x90,0x90,0x90,0x7c,0x00,0x44,0x64,0x54,0x4c,0x44,0x00,0x00,0x08,0x36,0x41,0x00,0x00,0x00,0x00,0x77,0x00,0x00,0x00,0x00,0x41,0x36,0x08,0x00,0x00,0x02,0x01,0x02,0x04,0x02,0x00,0x3c,0x26,0x23,0x26,0x3c,0x00,0x00,0x00,0x00,0x80,0xe0,0xe0,0xe0,0xe0,0x60,0x60,0xe0,0xe0,0xc0,0x80,0x00,0x00,0x00,0x04,0x0c,0x1c,0x1c,0x1c,0x18,0x38,0x38,0x78,0x70,0x70,0xf0,0xa0,0xa0,0x08, +0x18,0x18,0x18,0x1c,0x1c,0x1c,0x1c,0x1c,0x18,0x18,0x18,0xf8,0xf8,0xfc,0xf0,0x10,0x10,0x00,0x00,0x80,0xe0,0xf8,0xf0,0x70,0x70,0x70,0x70,0x60,0x60,0xe0,0xe0,0xe0,0xe0,0xe0,0xe0,0xc0,0xc0,0xc0,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0xc0,0xf8,0xfc,0xfe,0xde,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xc0,0xf0,0xf8,0xfc,0x3e,0x1e,0x06,0x01,0x00,0x00,0x00,0x7f,0x41,0x41,0x41,0x7f,0x00,0x7f,0x41,0x41,0x41,0x7f,0x00,0x00,0x80,0xc0,0xe0,0x7e,0x5b,0x4f,0x5b,0xfe,0xc0,0x00,0x00,0xc0,0x00,0xdc,0xd7,0xde,0xde,0xde,0xd7,0xdc,0x00,0xc0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0f,0x7f,0xff,0xf3,0xe0,0xc0,0xc0,0xc0,0xf3,0xff,0xff,0x00,0x00,0x00,0x00,0x00,0x20,0x70,0x78,0x78,0xf8,0xf8,0xdc,0xcc,0x8c,0x84,0x07,0x03,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xfc,0xff,0xff,0xff,0x00,0x00,0x00,0xc0,0xfc,0xff,0x1f,0x03,0x01,0x00,0x00,0xc0,0xe0,0xfc,0x7f,0x1f,0x0f,0x03,0x80,0xe0,0xfc,0xff,0x1f,0x03,0x00,0x00,0x00,0x00,0x00,0xe0,0xfc,0xff,0x3f,0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x07,0x0f,0x0f,0x0f,0x0e,0x1e,0x1e,0x0e,0x0c,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x69,0x69,0x6f,0x26,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x0f,0x1f,0x3f,0x3c,0x78,0x70,0x60,0x00,0x00,0x00,0x7f,0x41,0x41,0x41,0x7f,0x00,0x7f,0x41,0x41,0x41,0x7f,0x00,0x30,0x7b,0x7f,0x78,0x30,0x20,0x20,0x30,0x78,0x7f,0x3b,0x00,0x03,0x00,0x0f,0x7f,0x0f,0x0f,0x0f,0x7f,0x0f,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x03,0x03,0x03,0x01,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x38,0x38,0x1c,0x1c,0x0e,0x0e,0x07,0x03,0x03,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x07,0x03,0x01,0x00, +0x00,0x00,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x00,0x00,0x00,0x0e,0x0f,0x07,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x07,0x03,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, +}; diff --git a/keyboards/handwired/owlet60/keymaps/oled_testing/keymap.c b/keyboards/handwired/owlet60/keymaps/oled_testing/keymap.c new file mode 100644 index 0000000000..f63ec18933 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/oled_testing/keymap.c @@ -0,0 +1,108 @@ +/* Copyright 2019 worthlessowl + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +// Defines the keycodes used by our macros in process_record_user +enum custom_keycodes { + QMKBEST = SAFE_RANGE, + QMKURL +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT_owlet60_full_bsp( + KC_1, KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_PGUP, \ + KC_2, KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_PGDOWN, \ + KC_3, KC_CAPS,KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_ENT, KC_HOME, \ + KC_LSFT,KC_Z, KC_X, KC_C, KC_V, KC_B, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_END, \ + KC_LCTRL, KC_LALT, KC_SPC, MO(1),KC_SPC, KC_RALT, KC_LEFT, KC_DOWN, KC_RIGHT \ + ), + + [1] = LAYOUT_owlet60_full_bsp( + KC_NO, KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, RGB_TOG, \ + KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, RGB_MOD, \ + KC_NO, KC_NO,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO,KC_NO, KC_NO, RGB_VAI, \ + KC_TRNS,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_N, KC_NO, KC_NO,KC_NO, KC_NO, KC_NO, KC_TRNS, RGB_VAD, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ) +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QMKBEST: + if (record->event.pressed) { + // when keycode QMKBEST is pressed + SEND_STRING("QMK is the best thing ever!"); + } else { + // when keycode QMKBEST is released + } + break; + case QMKURL: + if (record->event.pressed) { + // when keycode QMKURL is pressed + SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER)); + } else { + // when keycode QMKURL is released + } + break; + } + return true; +} + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +void led_set_user(uint8_t usb_led) { + +} + +#ifdef OLED_DRIVER_ENABLE +oled_rotation_t oled_init_user(oled_rotation_t rotation) { + //return OLED_ROTATION_180; + return OLED_ROTATION_180; +} +void oled_task_user(void) { + // Host Keyboard Layer Status + /*oled_write_P(PSTR("Lyr: "), false); + switch (get_highest_layer(layer_state)) { + case 0: + oled_write_P(PSTR("Alpha\n"), false); + break; + case 1: + oled_write_P(PSTR("FN\n"), false); + break; + default: + // Or use the write_ln shortcut over adding '\n' to the end of your string + oled_write_ln_P(PSTR("Undefined"), false); + } + + uint8_t led_usb_state = host_keyboard_leds(); + oled_write_P(led_usb_state & (1<<USB_LED_CAPS_LOCK) ? PSTR("CAPLCK ") : PSTR(" "), false); + */ + + static const char PROGMEM qmk_logo[] = { + 0x80,0x81,0x82,0x83,0x84,0x85,0x86,0x87,0x88,0x89,0x8a,0x8b,0x8c,0x8d,0x8e,0x8f,0x90,0x91,0x92,0x93,0x94, + 0xa0,0xa1,0xa2,0xa3,0xa4,0xa5,0xa6,0xa7,0xa8,0xa9,0xaa,0xab,0xac,0xad,0xae,0xaf,0xb0,0xb1,0xb2,0xb3,0xb4, + 0xc0,0xc1,0xc2,0xc3,0xc4,0xc5,0xc6,0xc7,0xc8,0xc9,0xca,0xcb,0xcc,0xcd,0xce,0xcf,0xd0,0xd1,0xd2,0xd3,0xd4,0 + }; + + oled_write_P(qmk_logo, false); +} +#endif diff --git a/keyboards/handwired/owlet60/keymaps/oled_testing/readme.md b/keyboards/handwired/owlet60/keymaps/oled_testing/readme.md new file mode 100644 index 0000000000..1d177ae102 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/oled_testing/readme.md @@ -0,0 +1 @@ +# The default keymap for owlet60
\ No newline at end of file diff --git a/keyboards/handwired/owlet60/keymaps/oled_testing/rules.mk b/keyboards/handwired/owlet60/keymaps/oled_testing/rules.mk new file mode 100644 index 0000000000..48a51b2250 --- /dev/null +++ b/keyboards/handwired/owlet60/keymaps/oled_testing/rules.mk @@ -0,0 +1 @@ +OLED_DRIVER_ENABLE = yes
\ No newline at end of file diff --git a/keyboards/handwired/owlet60/matrix.c b/keyboards/handwired/owlet60/matrix.c new file mode 100644 index 0000000000..994f527ec7 --- /dev/null +++ b/keyboards/handwired/owlet60/matrix.c @@ -0,0 +1,315 @@ +/* +Copyright 2019 worthlessowl +based on work by: +Jun Wako <wakojun@gmail.com> +Cole Markham <cole@ccmcomputing.net> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +/* + * scan matrix + */ +#include <stdint.h> +#include <stdbool.h> +#include "owlet60.h" +#include "wait.h" +#include "print.h" +#include "debug.h" +#include "util.h" +#include "matrix.h" +#include "config.h" +#include "timer.h" + +#if (MATRIX_COLS <= 8) +# define print_matrix_header() print("\nr/c 01234567\n") +# define print_matrix_row(row) print_bin_reverse8(matrix_get_row(row)) +# define matrix_bitpop(i) bitpop(matrix[i]) +# define ROW_SHIFTER ((uint8_t)1) +#elif (MATRIX_COLS <= 16) +# define print_matrix_header() print("\nr/c 0123456789ABCDEF\n") +# define print_matrix_row(row) print_bin_reverse16(matrix_get_row(row)) +# define matrix_bitpop(i) bitpop16(matrix[i]) +# define ROW_SHIFTER ((uint16_t)1) +#elif (MATRIX_COLS <= 32) +# define print_matrix_header() print("\nr/c 0123456789ABCDEF0123456789ABCDEF\n") +# define print_matrix_row(row) print_bin_reverse32(matrix_get_row(row)) +# define matrix_bitpop(i) bitpop32(matrix[i]) +# define ROW_SHIFTER ((uint32_t)1) +#endif + +static const uint8_t row_pins[MATRIX_ROWS] = MATRIX_ROW_PINS; +static const uint8_t col_select_pins[3] = MATRIX_COL_SELECT_PINS; +static const uint8_t dat_pin = MATRIX_COL_DATA_PIN; + +/* matrix state(1:on, 0:off) */ +static matrix_row_t raw_matrix[MATRIX_ROWS]; //raw values +static matrix_row_t matrix[MATRIX_ROWS]; //raw values + +/* 2d array containing binary representation of its index */ +static const uint8_t num_in_binary[8][3] = { + {0, 0, 0}, + {0, 0, 1}, + {0, 1, 0}, + {0, 1, 1}, + {1, 0, 0}, + {1, 0, 1}, + {1, 1, 0}, + {1, 1, 1}, +}; + +static void select_col_analog(uint8_t col); +static void mux_pin_control(const uint8_t binary[]); +void debounce_init(uint8_t num_rows); +void debounce(matrix_row_t raw[], matrix_row_t cooked[], uint8_t num_rows, bool changed); + + +__attribute__ ((weak)) +void matrix_init_user(void) {} + +__attribute__ ((weak)) +void matrix_scan_user(void) {} + +__attribute__ ((weak)) +void matrix_init_kb(void) { + matrix_init_user(); +} + +__attribute__ ((weak)) +void matrix_scan_kb(void) { + matrix_scan_user(); +} + +inline +uint8_t matrix_rows(void) +{ + return MATRIX_ROWS; +} + +inline +uint8_t matrix_cols(void) +{ + return MATRIX_COLS; +} + +inline +bool matrix_is_on(uint8_t row, uint8_t col) +{ + return (matrix[row] & ((matrix_row_t)1<<col)); +} + +inline +matrix_row_t matrix_get_row(uint8_t row) +{ + // Matrix mask lets you disable switches in the returned matrix data. For example, if you have a + // switch blocker installed and the switch is always pressed. +#ifdef MATRIX_MASKED + return matrix[row] & matrix_mask[row]; +#else + return matrix[row]; +#endif +} + +void matrix_print(void) +{ + print_matrix_header(); + + for (uint8_t row = 0; row < MATRIX_ROWS; row++) { + phex(row); print(": "); + print_matrix_row(row); + print("\n"); + } +} + +uint8_t matrix_key_count(void) +{ + uint8_t count = 0; + for (uint8_t i = 0; i < MATRIX_ROWS; i++) { + count += matrix_bitpop(i); + } + return count; +} + +// uses standard row code +static void select_row(uint8_t row) +{ + setPinOutput(row_pins[row]); + writePinLow(row_pins[row]); +} + +static void unselect_row(uint8_t row) +{ + setPinInputHigh(row_pins[row]); +} + +static void unselect_rows(void) +{ + for(uint8_t x = 0; x < MATRIX_ROWS; x++) { + setPinInputHigh(row_pins[x]); + } +} + +static void init_pins(void) { // still need some fixing, this might not work + unselect_rows(); // with the loop + /* + for (uint8_t x = 0; x < MATRIX_COLS; x++) { + setPinInputHigh(col_pins[x]); + } + */ + setPinInputHigh(dat_pin); +} + +static bool read_cols_on_row(matrix_row_t current_matrix[], uint8_t current_row) +{ + // Store last value of row prior to reading + matrix_row_t last_row_value = current_matrix[current_row]; + + // Clear data in matrix row + current_matrix[current_row] = 0; + + // Select row and wait for row selecton to stabilize + select_row(current_row); + wait_us(30); + + // For each col... + for(uint8_t col_index = 0; col_index < MATRIX_COLS; col_index++) { + + // Select the col pin to read (active low) + select_col_analog(col_index); + wait_us(30); + uint8_t pin_state = readPin(dat_pin); + + // Populate the matrix row with the state of the col pin + current_matrix[current_row] |= pin_state ? 0 : (ROW_SHIFTER << col_index); + } + + // Unselect row + unselect_row(current_row); + + return (last_row_value != current_matrix[current_row]); +} + + +void matrix_init(void) { + + // initialize key pins + init_pins(); + + // initialize matrix state: all keys off + for (uint8_t i=0; i < MATRIX_ROWS; i++) { + raw_matrix[i] = 0; + matrix[i] = 0; + } + + debounce_init(MATRIX_ROWS); + + matrix_init_quantum(); + + setPinInput(D5); + writePinLow(D5); + + setPinInput(B0); + writePinLow(B0); +} + +// modified for per col read matrix scan +uint8_t matrix_scan(void) +{ + bool changed = false; + + for (uint8_t current_row = 0; current_row < MATRIX_ROWS; current_row++) { + changed |= read_cols_on_row(raw_matrix, current_row); + } + + debounce(raw_matrix, matrix, MATRIX_ROWS, changed); + + matrix_scan_quantum(); + return (uint8_t)changed; +} + +/* +uint8_t matrix_scan(void) +{ + bool changed = false; + +#if (DIODE_DIRECTION == COL2ROW) + // Set row, read cols + for (uint8_t current_row = 0; current_row < MATRIX_ROWS; current_row++) { + changed |= read_cols_on_row(raw_matrix, current_row); + } +#endif + + debounce(raw_matrix, matrix, MATRIX_ROWS, changed); + + matrix_scan_quantum(); + return (uint8_t)changed; +} +*/ + +static void select_col_analog(uint8_t col) { + switch(col) { + + case 0: + mux_pin_control(num_in_binary[0]); + break; + case 1: + mux_pin_control(num_in_binary[1]); + break; + case 2: + mux_pin_control(num_in_binary[2]); + break; + case 3: + mux_pin_control(num_in_binary[3]); + break; + case 4: + mux_pin_control(num_in_binary[4]); + break; + case 5: + mux_pin_control(num_in_binary[5]); + break; + case 6: + mux_pin_control(num_in_binary[6]); + break; + case 7: + mux_pin_control(num_in_binary[7]); + break; + default: + break; + } +} + +static void mux_pin_control(const uint8_t binary[]) { + // set pin0 + setPinOutput(col_select_pins[0]); + if(binary[2] == 0) { + writePinLow(col_select_pins[0]); + } + else { + writePinHigh(col_select_pins[0]); + } + // set pin1 + setPinOutput(col_select_pins[1]); + if(binary[1] == 0) { + writePinLow(col_select_pins[1]); + } + else { + writePinHigh(col_select_pins[1]); + } + // set pin2 + setPinOutput(col_select_pins[2]); + if(binary[0] == 0) { + writePinLow(col_select_pins[2]); + } + else { + writePinHigh(col_select_pins[2]); + } +} diff --git a/keyboards/handwired/owlet60/owlet60.c b/keyboards/handwired/owlet60/owlet60.c new file mode 100644 index 0000000000..42d24a291a --- /dev/null +++ b/keyboards/handwired/owlet60/owlet60.c @@ -0,0 +1,53 @@ +/* Copyright 2019 worthlessowl + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "owlet60.h" + +// Optional override functions below. +// You can leave any or all of these undefined. +// These are only required if you want to perform custom actions. + + +/* +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); + +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); + oled_task_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} + +*/ diff --git a/keyboards/handwired/owlet60/owlet60.h b/keyboards/handwired/owlet60/owlet60.h new file mode 100644 index 0000000000..f17f40fdaf --- /dev/null +++ b/keyboards/handwired/owlet60/owlet60.h @@ -0,0 +1,98 @@ +/* Copyright 2019 worthlessowl + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT_owlet60_split_bsp( \ + k50, k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0e, k0f, \ + k51, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, k1e, \ + k52, k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, k3d, k3e, \ + k40, k41, k42, k43, k44, k45, k46, k47, k48 \ +) { \ + { k50, k11, k13, k15, k07, k19, k1b, k1d}, \ + { k51, k21, k23, k25, k17, k29, k2b, k3d}, \ + { k52, k31, k33, k35, k27, k39, k3b, k47}, \ + { k40, k41, k42, k43, k37, k45, k46, k48}, \ + { k30, k32, k34, k44, k38, k3a, k3c, k3e}, \ + { k20, k22, k24, k36, k28, k2a, k2c, k2d}, \ + { k10, k12, k14, k26, k18, k1a, k1c, k1e}, \ + { k00, k02, k04, k16, k08, k0a, k0c, k0f}, \ + { k01, k03, k05, k06, k09, k0b, k0d, k0e} \ +} + +#define LAYOUT_owlet60_full_bsp( \ + k50, k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0f, \ + k51, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, k1e, \ + k52, k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, k2d, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, k3d, k3e, \ + k40, k41, k42, k43, k44, k45, k46, k47, k48 \ +) { \ + { k50, k11, k13, k15, k07, k19, k1b, k1d}, \ + { k51, k21, k23, k25, k17, k29, k2b, k3d}, \ + { k52, k31, k33, k35, k27, k39, k3b, k47}, \ + { k40, k41, k42, k43, k37, k45, k46, k48}, \ + { k30, k32, k34, k44, k38, k3a, k3c, k3e}, \ + { k20, k22, k24, k36, k28, k2a, k2c, k2d}, \ + { k10, k12, k14, k26, k18, k1a, k1c, k1e}, \ + { k00, k02, k04, k16, k08, k0a, k0c, k0f}, \ + { k01, k03, k05, k06, k09, k0b, k0d, KC_NO} \ +} + +#define LAYOUT_owlet60_60_percent_split_bsp( \ + k50, k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k0e, \ + k51, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \ + k52, k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, k3d, \ + k40, k41, k42, k43, k44, k45, k47 \ +) { \ + { k50, k11, k13, k15, k07, k19, k1b, k1d}, \ + { k51, k21, k23, k25, k17, k29, k2b, k3d}, \ + { k52, k31, k33, k35, k27, k39, k3b, k47}, \ + { k40, k41, k42, k43, k37, k45, KC_NO, KC_NO}, \ + { k30, k32, k34, k44, k38, k3a, k3c, KC_NO}, \ + { k20, k22, k24, k36, k28, k2a, k2c, KC_NO}, \ + { k10, k12, k14, k26, k18, k1a, k1c, KC_NO}, \ + { k00, k02, k04, k16, k08, k0a, k0c, KC_NO}, \ + { k01, k03, k05, k06, k09, k0b, k0d, k0e} \ +} + +#define LAYOUT_owlet60_60_percent_full_bsp( \ + k50, k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, \ + k51, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \ + k52, k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, k3d, \ + k40, k41, k42, k43, k44, k45, k47 \ +) { \ + { k50, k11, k13, k15, k07, k19, k1b, k1d}, \ + { k51, k21, k23, k25, k17, k29, k2b, k3d}, \ + { k52, k31, k33, k35, k27, k39, k3b, k47}, \ + { k40, k41, k42, k43, k37, k45, KC_NO, KC_NO}, \ + { k30, k32, k34, k44, k38, k3a, k3c, KC_NO}, \ + { k20, k22, k24, k36, k28, k2a, k2c, KC_NO}, \ + { k10, k12, k14, k26, k18, k1a, k1c, KC_NO}, \ + { k00, k02, k04, k16, k08, k0a, k0c, KC_NO}, \ + { k01, k03, k05, k06, k09, k0b, k0d, KC_NO} \ +} diff --git a/keyboards/handwired/owlet60/readme.md b/keyboards/handwired/owlet60/readme.md new file mode 100644 index 0000000000..05439e7eb4 --- /dev/null +++ b/keyboards/handwired/owlet60/readme.md @@ -0,0 +1,13 @@ +# owlet60 + +Owlet60, a TGR Alice inspired 60%-65% keyboard. Powered with a Pro Micro and 4051 mux multiplexed matrix. PCB can be permanently snapped off for a 60% layout. + +Keyboard Maintainer: [worthlessowl](https://github.com/worthlessowl) +Hardware Supported: Owlet60 PCB, standard Pro Micro +Hardware Availability: Keyboard is running on a local pre order as of 24 September 2019, limited quantity + +Make example for this keyboard (after setting up your build environment): + + make handwired/owlet60:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/owlet60/rules.mk b/keyboards/handwired/owlet60/rules.mk new file mode 100644 index 0000000000..6d8bdfd1c6 --- /dev/null +++ b/keyboards/handwired/owlet60/rules.mk @@ -0,0 +1,48 @@ +SRC += matrix.c + +# MCU name +MCU = atmega32u4 + + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# atmega32a bootloadHID +BOOTLOADER = caterina + + +# If you don't know the bootloader type, then you can specify the +# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +# OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) +CUSTOM_MATRIX = yes +OLED_DRIVER_ENABLE = no
\ No newline at end of file diff --git a/keyboards/handwired/pilcrow/rules.mk b/keyboards/handwired/pilcrow/rules.mk index 67badc8207..b5e96d74bf 100644 --- a/keyboards/handwired/pilcrow/rules.mk +++ b/keyboards/handwired/pilcrow/rules.mk @@ -1,52 +1,15 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable diff --git a/keyboards/handwired/postageboard/config.h b/keyboards/handwired/postageboard/config.h new file mode 100644 index 0000000000..417cc9901c --- /dev/null +++ b/keyboards/handwired/postageboard/config.h @@ -0,0 +1,21 @@ +/* +Copyright 2019 Yan-Fa Li + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + diff --git a/keyboards/handwired/postageboard/keymaps/default/keymap.c b/keyboards/handwired/postageboard/keymaps/default/keymap.c new file mode 100644 index 0000000000..a42697a9b1 --- /dev/null +++ b/keyboards/handwired/postageboard/keymaps/default/keymap.c @@ -0,0 +1,51 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +// Defines names for use in layer keycodes and the keymap +enum layer_names { + _BASE, + _FN +}; + +// Defines the keycodes used by our macros in process_record_user +enum custom_keycodes { + QMKURL = SAFE_RANGE +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Base */ + [_BASE] = LAYOUT( + KC_A, KC_1, MO(_FN) + ), + [_FN] = LAYOUT( + RESET, QMKURL, _______ + ) +}; + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QMKURL: + if (record->event.pressed) { + // when keycode QMKURL is pressed + SEND_STRING("https://qmk.fm/" SS_TAP(X_ENTER)); + } else { + // when keycode QMKURL is released + } + break; + } + return true; +} diff --git a/keyboards/handwired/postageboard/keymaps/default/readme.md b/keyboards/handwired/postageboard/keymaps/default/readme.md new file mode 100644 index 0000000000..c166556a85 --- /dev/null +++ b/keyboards/handwired/postageboard/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for PostageBoard diff --git a/keyboards/handwired/postageboard/mini/config.h b/keyboards/handwired/postageboard/mini/config.h new file mode 100644 index 0000000000..ac7d468855 --- /dev/null +++ b/keyboards/handwired/postageboard/mini/config.h @@ -0,0 +1,61 @@ +/* +Copyright 2019 Yan-Fa Li + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0xB07D +#define DEVICE_VER 0x0002 +#define MANUFACTURER LifeIsOnTheWire +#define PRODUCT PostageBoard +#define DESCRIPTION "A Handwire Controller Board Round 2" + +/* key matrix size */ +#define MATRIX_ROWS 1 +#define MATRIX_COLS 3 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS { D5 } +#define MATRIX_COL_PINS { E6, B3, B7 } +#define UNUSED_PINS { D0, D1, D2, D3, D4, D6, D7, B4, B5, B6, C6, C7, B2, B1, B0, F7, F6, F5, F4, F1, F0 } + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* Bootmagic Lite key configuration */ +// #define BOOTMAGIC_LITE_ROW 0 +// #define BOOTMAGIC_LITE_COLUMN 0 diff --git a/keyboards/handwired/postageboard/mini/mini.c b/keyboards/handwired/postageboard/mini/mini.c new file mode 100644 index 0000000000..381ad975f0 --- /dev/null +++ b/keyboards/handwired/postageboard/mini/mini.c @@ -0,0 +1,18 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "mini.h" + diff --git a/keyboards/handwired/postageboard/mini/mini.h b/keyboards/handwired/postageboard/mini/mini.h new file mode 100644 index 0000000000..28ee58ef13 --- /dev/null +++ b/keyboards/handwired/postageboard/mini/mini.h @@ -0,0 +1,34 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +/* This is a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT( \ + k00, k01, k02 \ +) \ +{ \ + { k00, k01, k02 } \ +} diff --git a/keyboards/handwired/postageboard/mini/rules.mk b/keyboards/handwired/postageboard/mini/rules.mk new file mode 100644 index 0000000000..96e8e574cf --- /dev/null +++ b/keyboards/handwired/postageboard/mini/rules.mk @@ -0,0 +1,29 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu + +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs diff --git a/keyboards/handwired/postageboard/postageboard.c b/keyboards/handwired/postageboard/postageboard.c new file mode 100644 index 0000000000..005ce313df --- /dev/null +++ b/keyboards/handwired/postageboard/postageboard.c @@ -0,0 +1 @@ +#include "postageboard.h" diff --git a/keyboards/handwired/postageboard/postageboard.h b/keyboards/handwired/postageboard/postageboard.h new file mode 100644 index 0000000000..5bd9ceee5a --- /dev/null +++ b/keyboards/handwired/postageboard/postageboard.h @@ -0,0 +1,26 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +#define LAYOUT( \ + k00, k01, k02 \ +) \ +{ \ + { k00, k01, k02 } \ +} diff --git a/keyboards/handwired/postageboard/r1/config.h b/keyboards/handwired/postageboard/r1/config.h new file mode 100644 index 0000000000..435e87fa1b --- /dev/null +++ b/keyboards/handwired/postageboard/r1/config.h @@ -0,0 +1,61 @@ +/* +Copyright 2019 Yan-Fa Li + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0xB07D +#define DEVICE_VER 0x0001 +#define MANUFACTURER LifeIsOnTheWire +#define PRODUCT PostageBoard +#define DESCRIPTION "A Handwire Controller Board" + +/* key matrix size */ +#define MATRIX_ROWS 1 +#define MATRIX_COLS 3 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS { B6 } +#define MATRIX_COL_PINS { B7, C6, C7 } +#define UNUSED_PINS { D4, D6, D7, B4, B5, D5, D3, D2, D1, D0, B2, B3, F0, F1, F4, F5, F6, F7, E6, B0, B1 } + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* Bootmagic Lite key configuration */ +// #define BOOTMAGIC_LITE_ROW 0 +// #define BOOTMAGIC_LITE_COLUMN 0 diff --git a/keyboards/handwired/postageboard/r1/r1.c b/keyboards/handwired/postageboard/r1/r1.c new file mode 100644 index 0000000000..e87edc145b --- /dev/null +++ b/keyboards/handwired/postageboard/r1/r1.c @@ -0,0 +1,18 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "r1.h" + diff --git a/keyboards/handwired/postageboard/r1/r1.h b/keyboards/handwired/postageboard/r1/r1.h new file mode 100644 index 0000000000..28ee58ef13 --- /dev/null +++ b/keyboards/handwired/postageboard/r1/r1.h @@ -0,0 +1,34 @@ +/* Copyright 2019 Yan-Fa Li + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +/* This is a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT( \ + k00, k01, k02 \ +) \ +{ \ + { k00, k01, k02 } \ +} diff --git a/keyboards/handwired/postageboard/r1/rules.mk b/keyboards/handwired/postageboard/r1/rules.mk new file mode 100644 index 0000000000..96e8e574cf --- /dev/null +++ b/keyboards/handwired/postageboard/r1/rules.mk @@ -0,0 +1,29 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu + +BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs diff --git a/keyboards/handwired/postageboard/readme.md b/keyboards/handwired/postageboard/readme.md new file mode 100644 index 0000000000..db9d0d11c5 --- /dev/null +++ b/keyboards/handwired/postageboard/readme.md @@ -0,0 +1,25 @@ +# Postage Board + +### Round 1 + + +### Round 2: Mini version + + +The Postage board is a controller board meant to aid people in making a hand wired keyboard. Controller boards are essentially the brain of the keyboard. It is similar to the common Teensy 2.0, and also the Pro Micro. + +However, neither the Teensy, nor the Pro Micro are designed for keyboards specifically. They are just general Arduino-like boards meant for a variety of DIY projects. The Postage Board is designed for mechanical keyboards specifically, and thus the process of assembling your keyboard is easier, and the final product is more refined. + +* Keyboard Maintainer: [LifeIsOnTheWire](https://github.com/LifeIsOnTheWire/Postage-Board) +* Hardware Supported: Available at GB +* Hardware Availability: Available at GB + +Make example for this keyboard (after setting up your build environment): + + make handwired/postageboard/r1:default + +or + + make handwired/postageboard/mini:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/postageboard/rules.mk b/keyboards/handwired/postageboard/rules.mk new file mode 100644 index 0000000000..a7fcf6bea6 --- /dev/null +++ b/keyboards/handwired/postageboard/rules.mk @@ -0,0 +1 @@ +DEFAULT_FOLDER=handwired/postageboard/mini diff --git a/keyboards/handwired/prime_exl/config.h b/keyboards/handwired/prime_exl/config.h index a2962c0746..ef6e204ec4 100644 --- a/keyboards/handwired/prime_exl/config.h +++ b/keyboards/handwired/prime_exl/config.h @@ -56,16 +56,16 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // TODO: refactor with new user EEPROM code (coming soon) #define EEPROM_MAGIC 0x451F -#define EEPROM_MAGIC_ADDR 32 +#define EEPROM_MAGIC_ADDR 34 // Bump this every time we change what we store // This will automatically reset the EEPROM with defaults // and avoid loading invalid data from the EEPROM #define EEPROM_VERSION 0x08 -#define EEPROM_VERSION_ADDR 34 +#define EEPROM_VERSION_ADDR 36 // Dynamic keymap starts after EEPROM version -#define DYNAMIC_KEYMAP_EEPROM_ADDR 35 -// Dynamic macro starts after dynamic keymaps (35+(4*10*9*2)) = (35+720) -#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 755 -#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 269 // 1024-DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR +#define DYNAMIC_KEYMAP_EEPROM_ADDR 37 +// Dynamic macro starts after dynamic keymaps (37+(4*10*9*2)) = (37+720) +#define DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR 757 +#define DYNAMIC_KEYMAP_MACRO_EEPROM_SIZE 267 // 1024-DYNAMIC_KEYMAP_MACRO_EEPROM_ADDR #define DYNAMIC_KEYMAP_MACRO_COUNT 16
\ No newline at end of file diff --git a/keyboards/handwired/prime_exl/rules.mk b/keyboards/handwired/prime_exl/rules.mk index 5cce4e8113..d7aca43dfc 100644 --- a/keyboards/handwired/prime_exl/rules.mk +++ b/keyboards/handwired/prime_exl/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/handwired/promethium/keymaps/default/keymap.c b/keyboards/handwired/promethium/keymaps/default/keymap.c index b09e30457c..207984407c 100644 --- a/keyboards/handwired/promethium/keymaps/default/keymap.c +++ b/keyboards/handwired/promethium/keymaps/default/keymap.c @@ -84,7 +84,6 @@ enum glow_modes { uint8_t glow_mode = GLOW_MIN; void turn_off_capslock(void); -extern keymap_config_t keymap_config; // layers, ordering is important! enum layers { diff --git a/keyboards/handwired/promethium/keymaps/priyadi/keymap.c b/keyboards/handwired/promethium/keymaps/priyadi/keymap.c index fbb1ae1d69..094eb15762 100644 --- a/keyboards/handwired/promethium/keymaps/priyadi/keymap.c +++ b/keyboards/handwired/promethium/keymaps/priyadi/keymap.c @@ -895,13 +895,13 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { /* Emoji * ,-----------------------------------------------------------------------------------. - * | | | | | | | | | | | | | + * | 💕 | 😢 | 😩 | 😍 | 😏 | 😂 | ♻ | 😒 | 🎶 | 👌 | 😔 | 😌 | * |------+------+------+------+------+-------------+------+------+------+------+------| - * | | | | | | | | | | | | | + * | 👍 | 🙏 | 😁 | 😅 | 😳 | 😊 | ❤ | 👋 | 😘 | 🙌 | 😎 | 🙈 | * |------+------+------+------+------+------+------+------+------+------+------+------| - * | | | | | | | | | | | | | + * | 👎 | 😴 | 👏 | 😭 | ✌ | 💔 | ☀ | 😊 | 😉 | 🌔 | 😕 | 🙉 | * |------+------+------+------+------+------+------+------+------+------+------+------| - * | | | | | | | | | | | | | + * | 💩 | 👀 | 💯 | | 💀 | 😈 | 😇 | 😱 | | 😋 | 😞 | 🙊 | * `-----------------------------------------------------------------------------------' */ [_EMOJI] = LAYOUT( diff --git a/keyboards/handwired/promethium/matrix.c b/keyboards/handwired/promethium/matrix.c index 3b8e5af820..b4a4c6396a 100644 --- a/keyboards/handwired/promethium/matrix.c +++ b/keyboards/handwired/promethium/matrix.c @@ -104,13 +104,6 @@ uint8_t matrix_cols(void) { } void matrix_init(void) { - - // To use PORTF disable JTAG with writing JTD bit twice within four cycles. - #if (defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1287__) || defined(__AVR_ATmega32U4__)) - MCUCR |= _BV(JTD); - MCUCR |= _BV(JTD); - #endif - // initialize row and col unselect_rows(); init_cols(); diff --git a/keyboards/handwired/promethium/rules.mk b/keyboards/handwired/promethium/rules.mk index dab92e52cf..19d20ee03f 100644 --- a/keyboards/handwired/promethium/rules.mk +++ b/keyboards/handwired/promethium/rules.mk @@ -1,50 +1,18 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. +# Processor frequency F_CPU = 8000000 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina # Build Options # change to "no" to disable the options, or define them in the Makefile in diff --git a/keyboards/handwired/pteron/rules.mk b/keyboards/handwired/pteron/rules.mk index 10218020e6..648387460b 100644 --- a/keyboards/handwired/pteron/rules.mk +++ b/keyboards/handwired/pteron/rules.mk @@ -1,45 +1,14 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina # Build Options @@ -55,4 +24,4 @@ NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https:/ BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality RGBLIGHT_ENABLE = no UNICODE_ENABLE = no -UNICODEMAP_ENABLE = no
\ No newline at end of file +UNICODEMAP_ENABLE = no diff --git a/keyboards/handwired/qc60/keymaps/default/keymap.c b/keyboards/handwired/qc60/keymaps/default/keymap.c index 88062d4ed4..a0f6250ffe 100644 --- a/keyboards/handwired/qc60/keymaps/default/keymap.c +++ b/keyboards/handwired/qc60/keymaps/default/keymap.c @@ -16,7 +16,6 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. diff --git a/keyboards/handwired/qc60/rules.mk b/keyboards/handwired/qc60/rules.mk index e61b18b00c..8859f5012d 100644 --- a/keyboards/handwired/qc60/rules.mk +++ b/keyboards/handwired/qc60/rules.mk @@ -1,48 +1,16 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/handwired/reddot/rules.mk b/keyboards/handwired/reddot/rules.mk index 00ca06dd40..4400decaac 100755 --- a/keyboards/handwired/reddot/rules.mk +++ b/keyboards/handwired/reddot/rules.mk @@ -1,45 +1,14 @@ - -#MCU = at90usb1287 +# MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# for avr upload -USB = /dev/cu.usbmodem1421 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp ifdef TEENSY2 BOOTLOADER = halfkay OPT_DEFS += -DATREUS_TEENSY2 @@ -51,11 +20,6 @@ else avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) endif -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - - # Build Options # change yes to no to disable # @@ -77,3 +41,5 @@ AUDIO_ENABLE = no # Audio output on port C6 # upload: build # $(ATREUS_UPLOAD_COMMAND) +# for avr upload +USB = /dev/cu.usbmodem1421 diff --git a/keyboards/handwired/retro_refit/rules.mk b/keyboards/handwired/retro_refit/rules.mk index 98aa19e6b1..04db510d13 100644 --- a/keyboards/handwired/retro_refit/rules.mk +++ b/keyboards/handwired/retro_refit/rules.mk @@ -1,54 +1,15 @@ - - # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # comment out to disable the options. diff --git a/keyboards/handwired/rs60/rules.mk b/keyboards/handwired/rs60/rules.mk index 7b4ec69d0d..ee10944c67 100644 --- a/keyboards/handwired/rs60/rules.mk +++ b/keyboards/handwired/rs60/rules.mk @@ -1,50 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = qmk-dfu -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - -LAYOUTS = ortho_5x12 - -# Boot Section Size in *bytes* -#OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # comment out to disable the options. # @@ -59,3 +25,4 @@ BACKLIGHT_ENABLE = no # Custom backlighting code is used, so this should not b AUDIO_ENABLE = no # This can be enabled if a speaker is connected to the expansion port. Not compatible with RGBLIGHT below RGBLIGHT_ENABLE = no # This can be enabled if a ws2812 strip is connected to the expansion port. +LAYOUTS = ortho_5x12 diff --git a/keyboards/handwired/slash/config.h b/keyboards/handwired/slash/config.h new file mode 100644 index 0000000000..56aec3144a --- /dev/null +++ b/keyboards/handwired/slash/config.h @@ -0,0 +1,59 @@ +/* +Copyright 2019 4sdftemp + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER asdftemp +#define PRODUCT Slash +#define DESCRIPTION 60% keyboard with bluetooth + +/* key matrix size */ +#define MATRIX_ROWS 8 +#define MATRIX_COLS 8 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS { C7, D6, B7, B6, B5, D7, C6, D0 } +#define MATRIX_COL_PINS { D2, F0, F1, F4, F5, F6, F7, D3 } +#define UNUSED_PINS +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE diff --git a/keyboards/handwired/slash/info.json b/keyboards/handwired/slash/info.json new file mode 100644 index 0000000000..713a77aaae --- /dev/null +++ b/keyboards/handwired/slash/info.json @@ -0,0 +1,74 @@ +{ + "keyboard_name": "slash", + "url": "", + "maintainer": "qmk", + "width": 16.75, + "height": 5, + "layouts": { + "LAYOUT": { + "layout": [ + {"label":"`", "x":1.75, "y":0}, + {"label":"1", "x":2.75, "y":0}, + {"label":"2", "x":3.75, "y":0}, + {"label":"3", "x":4.75, "y":0}, + {"label":"4", "x":5.75, "y":0}, + {"label":"5", "x":6.75, "y":0}, + {"label":"6", "x":7.75, "y":0}, + {"label":"7", "x":8.75, "y":0}, + {"label":"8", "x":9.75, "y":0}, + {"label":"9", "x":10.75, "y":0}, + {"label":"0", "x":11.75, "y":0}, + {"label":"-", "x":12.75, "y":0}, + {"label":"=", "x":13.75, "y":0}, + {"label":"Backspace", "x":14.75, "y":0, "w":2}, + {"label":"Tab", "x":1.25, "y":1, "w":1.5}, + {"label":"Q", "x":2.75, "y":1}, + {"label":"W", "x":3.75, "y":1}, + {"label":"E", "x":4.75, "y":1}, + {"label":"R", "x":5.75, "y":1}, + {"label":"T", "x":6.75, "y":1}, + {"label":"Y", "x":7.75, "y":1}, + {"label":"U", "x":8.75, "y":1}, + {"label":"I", "x":9.75, "y":1}, + {"label":"O", "x":10.75, "y":1}, + {"label":"P", "x":11.75, "y":1}, + {"label":"[", "x":12.75, "y":1}, + {"label":"]", "x":13.75, "y":1}, + {"label":"\\", "x":14.75, "y":1, "w":1.5}, + {"label":"Caps Lock", "x":1, "y":2, "w":1.75}, + {"label":"A", "x":2.75, "y":2}, + {"label":"S", "x":3.75, "y":2}, + {"label":"D", "x":4.75, "y":2}, + {"label":"F", "x":5.75, "y":2}, + {"label":"G", "x":6.75, "y":2}, + {"label":"H", "x":7.75, "y":2}, + {"label":"J", "x":8.75, "y":2}, + {"label":"K", "x":9.75, "y":2}, + {"label":"L", "x":10.75, "y":2}, + {"label":";", "x":11.75, "y":2}, + {"label":"'", "x":12.75, "y":2}, + {"label":"Enter", "x":13.75, "y":2, "w":2.25}, + {"label":"Shift", "x":0.5, "y":3, "w":2.25}, + {"label":"Z", "x":2.75, "y":3}, + {"label":"X", "x":3.75, "y":3}, + {"label":"C", "x":4.75, "y":3}, + {"label":"V", "x":5.75, "y":3}, + {"label":"B", "x":6.75, "y":3}, + {"label":"N", "x":7.75, "y":3}, + {"label":"M", "x":8.75, "y":3}, + {"label":",", "x":9.75, "y":3}, + {"label":".", "x":10.75, "y":3}, + {"label":"/", "x":11.75, "y":3}, + {"label":"Shift", "x":12.75, "y":3, "w":2.75}, + {"label":"Ctrl", "x":0, "y":4, "w":1.25}, + {"label":"GUI", "x":1.25, "y":4, "w":1.25}, + {"label":"Alt", "x":2.5, "y":4, "w":1.25}, + {"label":"Space", "x":3.75, "y":4, "w":6.25}, + {"label":"Alt", "x":10, "y":4, "w":1.25}, + {"label":"GUI", "x":11.25, "y":4, "w":1.25}, + {"label":"Menu", "x":12.5, "y":4, "w":1.25}, + {"label":"Ctrl", "x":13.75, "y":4, "w":1.25} + ] + } + } +} diff --git a/keyboards/handwired/slash/keymaps/default/config.h b/keyboards/handwired/slash/keymaps/default/config.h new file mode 100644 index 0000000000..05a8d25b91 --- /dev/null +++ b/keyboards/handwired/slash/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 4sdftemp + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/slash/keymaps/default/keymap.c b/keyboards/handwired/slash/keymaps/default/keymap.c new file mode 100644 index 0000000000..f57ef8b645 --- /dev/null +++ b/keyboards/handwired/slash/keymaps/default/keymap.c @@ -0,0 +1,11 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + LAYOUT( /* Base */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, KC_APP, KC_RCTL + ), +}; diff --git a/keyboards/handwired/slash/keymaps/default/readme.md b/keyboards/handwired/slash/keymaps/default/readme.md new file mode 100644 index 0000000000..517377a4b0 --- /dev/null +++ b/keyboards/handwired/slash/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for slash diff --git a/keyboards/handwired/slash/readme.md b/keyboards/handwired/slash/readme.md new file mode 100644 index 0000000000..954a847388 --- /dev/null +++ b/keyboards/handwired/slash/readme.md @@ -0,0 +1,19 @@ +# slash + + + +I found this project a while ago on [Reddit](https://www.reddit.com/r/MechanicalKeyboards/comments/6v3b6f/build_slash_keyboard_handwired_bluetooth/). This keyboard uses 61 keys in a 8x8 matrix. That bring the required pins to 16 which leaves 1 pin free. Unfortunately I couldn't get the firmware to compile on kbfirmware.com(the way [ND1BV](https://imgur.com/user/ND1BV) described it). So I decided to create the config myself and share it. I changed the wiring of the pins a little bit showed [here](https://i.imgur.com/WZ93xHx.png) + +Keyboard Maintainer: [asdftemp](https://github.com/asdftemp) +Hardware Supported: Adafruit Feather 32u4 Bluefruit LE +Hardware Availability: [Adafruit shop](https://www.adafruit.com/product/2829) + +Make example for this keyboard (after setting up your build environment): + + make handwired/slash:default + +Flashing should be done trough avrdude. Full make command is: + + make handwired/slash:default:flash + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/slash/rules.mk b/keyboards/handwired/slash/rules.mk new file mode 100644 index 0000000000..4aba5bdeb9 --- /dev/null +++ b/keyboards/handwired/slash/rules.mk @@ -0,0 +1,30 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency +F_CPU = 8000000 + +# Bootloader selection +BOOTLOADER = caterina + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = no # Console for debug +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +UNICODE_ENABLE = no # Unicode +#BLUETOOTH_ENABLE = Yes # Enable Bluetooth with the Adafruit EZ-Key HID +BLUETOOTH = AdafruitBLE +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs diff --git a/keyboards/handwired/slash/slash.c b/keyboards/handwired/slash/slash.c new file mode 100644 index 0000000000..59902b5074 --- /dev/null +++ b/keyboards/handwired/slash/slash.c @@ -0,0 +1,16 @@ +/* Copyright 2019 4sdftemp + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "slash.h" diff --git a/keyboards/handwired/slash/slash.h b/keyboards/handwired/slash/slash.h new file mode 100644 index 0000000000..6c1342d6b2 --- /dev/null +++ b/keyboards/handwired/slash/slash.h @@ -0,0 +1,36 @@ +/* Copyright 2019 asdftemp + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +#define LAYOUT( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k0B, k0C, k0D, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k1B, k1C, k1D, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, \ + k40, k41, k42, k43, k44, k45, k46, k47 \ +) \ +{ \ + { k00, k02, k04, k06, k08, k0A, k0C, KC_NO }, \ + { k01, k03, k05, k07, k09, k0B, k0D, KC_NO }, \ + { k10, k12, k14, k16, k18, k1A, k1C, k45 }, \ + { k11, k13, k15, k17, k19, k1B, k1D, k44 }, \ + { k21, k23, k25, k27, k29, k2B, KC_NO, k42 }, \ + { k20, k22, k24, k26, k28, k2A, k2C, k43 }, \ + { k31, k33, k35, k37, k39, k3B, k47, k40 }, \ + { k30, k32, k34, k36, k38, k3A, k46, k41 } \ +} diff --git a/keyboards/handwired/space_oddity/rules.mk b/keyboards/handwired/space_oddity/rules.mk index b597ef2b09..43fc1f34a3 100644 --- a/keyboards/handwired/space_oddity/rules.mk +++ b/keyboards/handwired/space_oddity/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # comment out to disable the options. # diff --git a/keyboards/handwired/splittest/config.h b/keyboards/handwired/splittest/config.h index a502d12382..56574f7529 100644 --- a/keyboards/handwired/splittest/config.h +++ b/keyboards/handwired/splittest/config.h @@ -33,12 +33,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define MATRIX_ROWS 2 #define MATRIX_COLS 1 -// wiring of each half -#define MATRIX_ROW_PINS { B3 } -#define MATRIX_COL_PINS { B6 } -#define SPLIT_HAND_PIN F6 -#define SOFT_SERIAL_PIN D1 - /* define if matrix has ghost */ //#define MATRIX_HAS_GHOST @@ -51,7 +45,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define LOCKING_RESYNC_ENABLE /* ws2812 RGB LED */ -#define RGB_DI_PIN D3 #define RGBLIGHT_ANIMATIONS #define RGBLED_NUM 12 #define RGBLED_SPLIT { 6, 6 } diff --git a/keyboards/handwired/splittest/promicro/config.h b/keyboards/handwired/splittest/promicro/config.h new file mode 100644 index 0000000000..c2a9c6002e --- /dev/null +++ b/keyboards/handwired/splittest/promicro/config.h @@ -0,0 +1,28 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +// wiring of each half +#define MATRIX_ROW_PINS { B3 } +#define MATRIX_COL_PINS { B6 } +#define SPLIT_HAND_PIN F6 +#define SOFT_SERIAL_PIN D1 + +/* ws2812 RGB LED */ +#define RGB_DI_PIN D3 diff --git a/keyboards/handwired/splittest/promicro/readme.md b/keyboards/handwired/splittest/promicro/readme.md new file mode 100644 index 0000000000..64a6f4c249 --- /dev/null +++ b/keyboards/handwired/splittest/promicro/readme.md @@ -0,0 +1,11 @@ +# Pro Micro splittest + +To trigger keypress, short together pins *B3* and *B6* (marked on the PCB as *14* and *10*). + +## Wiring +- Add switches to both Pro Micros across B3 and B6 pins +- Add pull-up resistor to left side between VCC and F6 +- Add pull-down resistors to right side between GND and F6 +- Connect the following pins on both sides together: D0, D1, GND, VCC +- Add I2C 4.7kOhm resistors between D0 and VCC, and D1 and VCC +- Wire Di of RGB strip for each half to D3 diff --git a/keyboards/handwired/splittest/promicro/rules.mk b/keyboards/handwired/splittest/promicro/rules.mk new file mode 100644 index 0000000000..e6fef51727 --- /dev/null +++ b/keyboards/handwired/splittest/promicro/rules.mk @@ -0,0 +1,12 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina diff --git a/keyboards/handwired/splittest/readme.md b/keyboards/handwired/splittest/readme.md index 3dbff32ed4..33dbc6e805 100644 --- a/keyboards/handwired/splittest/readme.md +++ b/keyboards/handwired/splittest/readme.md @@ -4,7 +4,10 @@ Split Tester A two-switch tester built using two Pro Micros, mainly intended to test RGB on split keyboards. Seen here: https://www.instagram.com/p/BvCPNzynwrV/ Keyboard Maintainer: [Bakingpy/nooges](https://github.com/nooges) -Hardware Supported: Pro Micro +Hardware Supported: Pro Micro, Teensy 2.0 +Hardware Availability: + +**See each individual board for pin infomation** Make example for this keyboard (after setting up your build environment): @@ -15,12 +18,3 @@ Example of flashing this keyboard: make handwired/splittest:default:avrdude See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). - -Wiring ------- -- Add switches to both Pro Micros across B3 and B6 pins -- Add pull-up resistor to left side between VCC and F6 -- Add pull-down resistors to right side between GND and F6 -- Connect the following pins on both sides together: D0, D1, GND, VCC -- Add I2C 4.7kOhm resistors between D0 and VCC, and D1 and VCC -- Wire Di of RGB strip for each half to D2 diff --git a/keyboards/handwired/splittest/rules.mk b/keyboards/handwired/splittest/rules.mk index 9512c0f648..2aa484db0b 100644 --- a/keyboards/handwired/splittest/rules.mk +++ b/keyboards/handwired/splittest/rules.mk @@ -1,47 +1,3 @@ -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. -BOOTLOADER = caterina - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -63,3 +19,5 @@ RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend SPLIT_KEYBOARD = yes + +DEFAULT_FOLDER = handwired/splittest/promicro diff --git a/keyboards/handwired/splittest/teensy_2/config.h b/keyboards/handwired/splittest/teensy_2/config.h new file mode 100644 index 0000000000..7c092db307 --- /dev/null +++ b/keyboards/handwired/splittest/teensy_2/config.h @@ -0,0 +1,31 @@ +/* Copyright 2019 + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +// wiring of each half +#define MATRIX_ROW_PINS { F5 } +#define MATRIX_COL_PINS { F7 } +#define SPLIT_HAND_PIN F0 +#define SOFT_SERIAL_PIN D1 + +/* ws2812 RGB LED */ +#define RGB_DI_PIN D3 + +// teensy has vbus detection issues - use usb detection instead +#define SPLIT_USB_DETECT diff --git a/keyboards/handwired/splittest/teensy_2/readme.md b/keyboards/handwired/splittest/teensy_2/readme.md new file mode 100644 index 0000000000..ed5f845d20 --- /dev/null +++ b/keyboards/handwired/splittest/teensy_2/readme.md @@ -0,0 +1,11 @@ +# Teensy 2.0 splittest + +To trigger keypress, short together pins *F5* and *F7* + +## Wiring +- Add switches to both Teensy 2s across F5 and F7 pins +- Add pull-up resistor to left side between VCC and F0 +- Add pull-down resistors to right side between GND and F0 +- Connect the following pins on both sides together: D0, D1, GND, VCC +- Add I2C 4.7kOhm resistors between D0 and VCC, and D1 and VCC +- Wire Di of RGB strip for each half to D3 diff --git a/keyboards/handwired/splittest/teensy_2/rules.mk b/keyboards/handwired/splittest/teensy_2/rules.mk new file mode 100644 index 0000000000..ae398e2588 --- /dev/null +++ b/keyboards/handwired/splittest/teensy_2/rules.mk @@ -0,0 +1,12 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay diff --git a/keyboards/handwired/steamvan/info.json b/keyboards/handwired/steamvan/info.json new file mode 100644 index 0000000000..1a057e5ca2 --- /dev/null +++ b/keyboards/handwired/steamvan/info.json @@ -0,0 +1,24 @@ +{ + "keyboard_name": "steamvan", + "url": "", + "maintainer": "qmk", + "width": 12.75, + "height": 4, + "layouts": { + "LAYOUT_standard": { + "layout": [{"label":"Tab", "x":0, "y":0}, {"label":"Q", "x":1, "y":0}, {"label":"W", "x":2, "y":0}, {"label":"E", "x":3, "y":0}, {"label":"R", "x":4, "y":0}, {"label":"T", "x":5, "y":0}, {"label":"Y", "x":6, "y":0}, {"label":"U", "x":7, "y":0}, {"label":"I", "x":8, "y":0}, {"label":"O", "x":9, "y":0}, {"label":"P", "x":10, "y":0}, {"label":"|", "x":11, "y":0, "w":1.75}, {"label":"Caps Lock", "x":0, "y":1, "w":1.25}, {"label":"A", "x":1.25, "y":1}, {"label":"S", "x":2.25, "y":1}, {"label":"D", "x":3.25, "y":1}, {"label":"F", "x":4.25, "y":1}, {"label":"G", "x":5.25, "y":1}, {"label":"H", "x":6.25, "y":1}, {"label":"J", "x":7.25, "y":1}, {"label":"K", "x":8.25, "y":1}, {"label":"L", "x":9.25, "y":1}, {"label":":", "x":10.25, "y":1}, {"label":"\"", "x":11.25, "y":1, "w":1.5}, {"label":"Shift", "x":0, "y":2, "w":1.75}, {"label":"Z", "x":1.75, "y":2}, {"label":"X", "x":2.75, "y":2}, {"label":"C", "x":3.75, "y":2}, {"label":"V", "x":4.75, "y":2}, {"label":"B", "x":5.75, "y":2}, {"label":"N", "x":6.75, "y":2}, {"label":"M", "x":7.75, "y":2}, {"label":"<", "x":8.75, "y":2}, {"label":">", "x":9.75, "y":2}, {"label":"?", "x":10.75, "y":2}, {"x":11.75, "y":2}, {"label":"Ctrl", "x":0, "y":3, "w":1.25}, {"label":"Win", "x":1.25, "y":3, "w":1.5}, {"label":"Alt", "x":2.75, "y":3, "w":1.25}, {"x":4, "y":3, "w":2.25}, {"x":6.25, "y":3, "w":2}, {"label":"Alt", "x":8.25, "y":3, "w":1.25}, {"label":"Win", "x":9.5, "y":3, "w":1.5}, {"label":"Menu", "x":11, "y":3, "w":1.75}] + }, + + "LAYOUT_arrow": { + "layout": [{"label":"Tab", "x":0, "y":0}, {"label":"Q", "x":1, "y":0}, {"label":"W", "x":2, "y":0}, {"label":"E", "x":3, "y":0}, {"label":"R", "x":4, "y":0}, {"label":"T", "x":5, "y":0}, {"label":"Y", "x":6, "y":0}, {"label":"U", "x":7, "y":0}, {"label":"I", "x":8, "y":0}, {"label":"O", "x":9, "y":0}, {"label":"P", "x":10, "y":0}, {"label":"|", "x":11, "y":0, "w":1.75}, {"label":"Caps Lock", "x":0, "y":1, "w":1.25}, {"label":"A", "x":1.25, "y":1}, {"label":"S", "x":2.25, "y":1}, {"label":"D", "x":3.25, "y":1}, {"label":"F", "x":4.25, "y":1}, {"label":"G", "x":5.25, "y":1}, {"label":"H", "x":6.25, "y":1}, {"label":"J", "x":7.25, "y":1}, {"label":"K", "x":8.25, "y":1}, {"label":"L", "x":9.25, "y":1}, {"label":":", "x":10.25, "y":1}, {"label":"\"", "x":11.25, "y":1, "w":1.5}, {"label":"Shift", "x":0, "y":2, "w":1.75}, {"label":"Z", "x":1.75, "y":2}, {"label":"X", "x":2.75, "y":2}, {"label":"C", "x":3.75, "y":2}, {"label":"V", "x":4.75, "y":2}, {"label":"B", "x":5.75, "y":2}, {"label":"N", "x":6.75, "y":2}, {"label":"M", "x":7.75, "y":2}, {"label":"<", "x":8.75, "y":2}, {"label":">", "x":9.75, "y":2}, {"label":"?", "x":10.75, "y":2}, {"x":11.75, "y":2}, {"label":"Ctrl", "x":0, "y":3, "w":1.25}, {"label":"Win", "x":1.25, "y":3, "w":1.5}, {"label":"Alt", "x":2.75, "y":3, "w":1.25}, {"x":4, "y":3, "w":2.25}, {"x":6.25, "y":3, "w":2}, {"x":8.25, "y":3, "w":1.5}, {"label":"Alt", "x":9.75, "y":3}, {"label":"Win", "x":10.75, "y":3}, {"label":"Menu", "x":11.75, "y":3}] + }, + + "LAYOUT_command": { + "layout": [{"label":"Tab", "x":0, "y":0}, {"label":"Q", "x":1, "y":0}, {"label":"W", "x":2, "y":0}, {"label":"E", "x":3, "y":0}, {"label":"R", "x":4, "y":0}, {"label":"T", "x":5, "y":0}, {"label":"Y", "x":6, "y":0}, {"label":"U", "x":7, "y":0}, {"label":"I", "x":8, "y":0}, {"label":"O", "x":9, "y":0}, {"label":"P", "x":10, "y":0}, {"label":"|", "x":11, "y":0, "w":1.75}, {"label":"Caps Lock", "x":0, "y":1, "w":1.25}, {"label":"A", "x":1.25, "y":1}, {"label":"S", "x":2.25, "y":1}, {"label":"D", "x":3.25, "y":1}, {"label":"F", "x":4.25, "y":1}, {"label":"G", "x":5.25, "y":1}, {"label":"H", "x":6.25, "y":1}, {"label":"J", "x":7.25, "y":1}, {"label":"K", "x":8.25, "y":1}, {"label":"L", "x":9.25, "y":1}, {"label":":", "x":10.25, "y":1}, {"label":"\"", "x":11.25, "y":1, "w":1.5}, {"label":"Shift", "x":0, "y":2, "w":1.75}, {"label":"Z", "x":1.75, "y":2}, {"label":"X", "x":2.75, "y":2}, {"label":"C", "x":3.75, "y":2}, {"label":"V", "x":4.75, "y":2}, {"label":"B", "x":5.75, "y":2}, {"label":"N", "x":6.75, "y":2}, {"label":"M", "x":7.75, "y":2}, {"label":"<", "x":8.75, "y":2}, {"label":">", "x":9.75, "y":2}, {"label":"?", "x":10.75, "y":2}, {"x":11.75, "y":2}, {"label":"Ctrl", "x":0, "y":3}, {"label":"Win", "x":1, "y":3}, {"label":"Alt", "x":2, "y":3}, {"x":3, "y":3}, {"x":4, "y":3, "w":2.25}, {"x":6.25, "y":3, "w":2}, {"x":8.25, "y":3, "w":1.5}, {"label":"Alt", "x":9.75, "y":3, "w":1.5}, {"label":"Win", "x":11.25, "y":3, "w":1.5}] + }, + + "LAYOUT_arrow_command": { + "layout": [{"label":"Tab", "x":0, "y":0}, {"label":"Q", "x":1, "y":0}, {"label":"W", "x":2, "y":0}, {"label":"E", "x":3, "y":0}, {"label":"R", "x":4, "y":0}, {"label":"T", "x":5, "y":0}, {"label":"Y", "x":6, "y":0}, {"label":"U", "x":7, "y":0}, {"label":"I", "x":8, "y":0}, {"label":"O", "x":9, "y":0}, {"label":"P", "x":10, "y":0}, {"label":"|", "x":11, "y":0, "w":1.75}, {"label":"Caps Lock", "x":0, "y":1, "w":1.25}, {"label":"A", "x":1.25, "y":1}, {"label":"S", "x":2.25, "y":1}, {"label":"D", "x":3.25, "y":1}, {"label":"F", "x":4.25, "y":1}, {"label":"G", "x":5.25, "y":1}, {"label":"H", "x":6.25, "y":1}, {"label":"J", "x":7.25, "y":1}, {"label":"K", "x":8.25, "y":1}, {"label":"L", "x":9.25, "y":1}, {"label":":", "x":10.25, "y":1}, {"label":"\"", "x":11.25, "y":1, "w":1.5}, {"label":"Shift", "x":0, "y":2, "w":1.75}, {"label":"Z", "x":1.75, "y":2}, {"label":"X", "x":2.75, "y":2}, {"label":"C", "x":3.75, "y":2}, {"label":"V", "x":4.75, "y":2}, {"label":"B", "x":5.75, "y":2}, {"label":"N", "x":6.75, "y":2}, {"label":"M", "x":7.75, "y":2}, {"label":"<", "x":8.75, "y":2}, {"label":">", "x":9.75, "y":2}, {"label":"?", "x":10.75, "y":2}, {"x":11.75, "y":2}, {"label":"Ctrl", "x":0, "y":3}, {"label":"Win", "x":1, "y":3}, {"label":"Alt", "x":2, "y":3}, {"x":3, "y":3}, {"x":4, "y":3, "w":2.25}, {"x":6.25, "y":3, "w":2}, {"x":8.25, "y":3, "w":1.5}, {"label":"Alt", "x":9.75, "y":3}, {"label":"Win", "x":10.75, "y":3}, {"label":"Menu", "x":11.75, "y":3}] + } + } +} diff --git a/keyboards/handwired/steamvan/keymaps/default/config.h b/keyboards/handwired/steamvan/keymaps/default/config.h new file mode 100644 index 0000000000..271f48d001 --- /dev/null +++ b/keyboards/handwired/steamvan/keymaps/default/config.h @@ -0,0 +1,3 @@ +#pragma once + +// place overrides here diff --git a/keyboards/handwired/steamvan/keymaps/default/keymap.c b/keyboards/handwired/steamvan/keymaps/default/keymap.c new file mode 100644 index 0000000000..e796f09409 --- /dev/null +++ b/keyboards/handwired/steamvan/keymaps/default/keymap.c @@ -0,0 +1,93 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +// This file is based on the default keyman the the MiniVan. + + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. + +enum layer_names { + _QW, + _DV, + _CM, + _L1, + _L2, + _L3, +}; + +// Curly braces have their own keys. These are defined to make them not mess up +// the grid in layer 2. +#define L_CURBR LSFT(KC_LBRC) +#define R_CURBR LSFT(KC_RBRC) + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_QW] = LAYOUT_standard( /* Qwerty */ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + MO(_L1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, MO(_L1), + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2), + KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, KC_SPC, KC_RALT, KC_ESC, TG(_L3) + ), + [_DV] = LAYOUT_standard( /* Dvorak */ + KC_TAB, KC_SLSH, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC, + MO(_L1), KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, MO(_L1), + KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, MO(_L2), + KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, KC_SPC, KC_RALT, KC_ESC, TG(_L3) + ), + [_CM] = LAYOUT_standard( /* Colemak */ + KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC, + MO(_L1), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, MO(_L1), + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2), + KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, KC_SPC, KC_RALT, KC_ESC, TG(_L3) + ), + [_L1] = LAYOUT_standard( /* LAYER 1 */ + KC_GRV, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, + _______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_DOWN, KC_UP, KC_LEFT, KC_RGHT, _______, + _______, KC_ESC, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT, + _______, KC_LGUI, _______, _______, _______, _______, _______, _______ + ), + [_L2] = LAYOUT_standard( /* LAYER 2 */ + _______, DF(_QW), DF(_DV), DF(_CM), _______, _______, _______, KC_7, KC_8, KC_9, KC_0, _______, + KC_ESC, KC_PIPE, KC_DQUO, KC_UNDS, KC_PLUS, L_CURBR, R_CURBR, KC_4, KC_5, KC_6, KC_VOLU, KC_ENT, + _______, _______, _______, _______, _______, _______, KC_0, KC_1, KC_2, KC_3, KC_VOLD, _______, + _______, _______, _______, _______, _______, _______, _______, _______ + ), + [_L3] = LAYOUT_standard( /* LAYER 3 */ + _______, _______, _______, _______, _______, _______, _______, KC_F1, KC_F2, KC_F3, KC_F4, _______, + KC_ESC, _______, _______, _______, _______, _______, _______, KC_F5, KC_F6, KC_F7, KC_F8, _______, + KC_LSFT, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_F9, KC_F10, KC_F11, KC_F12, _______, + _______, KC_LSFT, KC_B, KC_SPC, KC_C, _______, _______, _______ + ) +}; + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/handwired/steamvan/keymaps/default/readme.md b/keyboards/handwired/steamvan/keymaps/default/readme.md new file mode 100644 index 0000000000..efc2165482 --- /dev/null +++ b/keyboards/handwired/steamvan/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for the SteamVan, based on the MiniVan default layout. diff --git a/keyboards/handwired/steamvan/keymaps/jmdaly/config.h b/keyboards/handwired/steamvan/keymaps/jmdaly/config.h new file mode 100644 index 0000000000..271f48d001 --- /dev/null +++ b/keyboards/handwired/steamvan/keymaps/jmdaly/config.h @@ -0,0 +1,3 @@ +#pragma once + +// place overrides here diff --git a/keyboards/handwired/steamvan/keymaps/jmdaly/keymap.c b/keyboards/handwired/steamvan/keymaps/jmdaly/keymap.c new file mode 100644 index 0000000000..2bc5432712 --- /dev/null +++ b/keyboards/handwired/steamvan/keymaps/jmdaly/keymap.c @@ -0,0 +1,80 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. + +enum { + // Layers + _L1, + _L2, + _L3, + _L4, + _L5 +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_L1] = LAYOUT_standard( /* Qwerty */ + LT(_L5, KC_TAB), KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + CTL_T(KC_ESC), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, LT(_L2, KC_QUOT), + KC_LSPO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSPC, + MO(_L2), KC_LGUI, MO(_L3), KC_ENT, LT(_L2, KC_SPC), KC_RALT, KC_BSLS, MO(_L4) + ), + [_L2] = LAYOUT_standard( /* LAYER 2 */ + KC_GRV, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, + _______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, _______, _______, + _______, KC_ESC, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_LBRC, KC_RBRC, KC_MNXT, _______, + _______, KC_LGUI, _______, _______, _______, _______, _______, MO(_L4) + ), + [_L3] = LAYOUT_standard( /* LAYER 3 */ + KC_MINS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, _______, + KC_EQL, KC_PIPE, KC_TILD, KC_UNDS, KC_PLUS, LSFT(KC_LBRC), LSFT(KC_RBRC), KC_4, KC_5, KC_6, KC_VOLU, KC_INS, + _______, _______, _______, KC_DQUO, _______, _______, KC_0, KC_1, KC_2, KC_3, KC_VOLD, _______, + _______, _______, _______, _______, _______, _______, _______, _______ + ), + [_L4] = LAYOUT_standard( /* LAYER 4 */ + RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_PGUP, _______, + KC_ESC, _______, _______, _______, _______, _______, _______, KC_F5, KC_F6, KC_HOME, KC_END, _______, + KC_LSFT, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_F9, KC_F10, KC_PGDN, KC_F12, _______, + _______, KC_LSFT, KC_B, KC_SPC, KC_C, _______, _______, _______ + ), + [_L5] = LAYOUT_standard( /* LAYER 5 */ + _______, LGUI(KC_1), LGUI(KC_2), LGUI(KC_3), LGUI(KC_4), LGUI(KC_5), LGUI(KC_6), LGUI(KC_7), LGUI(KC_8), LGUI(KC_9), LGUI(KC_0), LGUI(KC_MINS), + KC_ESC, _______, _______, _______, _______, _______, _______, KC_F5, KC_F6, KC_HOME, KC_END, _______, + KC_LSFT, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_F9, KC_F10, KC_PGDN, KC_F12, _______, + _______, KC_LSFT, KC_B, KC_SPC, KC_C, _______, _______, _______ + ) +}; + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} diff --git a/keyboards/handwired/steamvan/keymaps/jmdaly/readme.md b/keyboards/handwired/steamvan/keymaps/jmdaly/readme.md new file mode 100644 index 0000000000..5aeae7064f --- /dev/null +++ b/keyboards/handwired/steamvan/keymaps/jmdaly/readme.md @@ -0,0 +1 @@ +# jmdaly's keymap for the steamvan diff --git a/keyboards/handwired/steamvan/readme.md b/keyboards/handwired/steamvan/readme.md new file mode 100644 index 0000000000..508d67f234 --- /dev/null +++ b/keyboards/handwired/steamvan/readme.md @@ -0,0 +1,24 @@ +# SteamVan + +The SteamVan is a 40% PCB that aims to meet the following goals: + +* Switches oriented such that the LEDs are South-facing, for + compatibility with Cherry profile keycaps. +* USB Type-C support in both A to C and C to C configurations. +* QMK support. +* ESD protection circuitry, including data line protection and a + polyfuse on the VCC line. +* Support for per-switch LED backlighting. +* Fits in MiniVan keyboard cases. + +More info on the project, including all of the design files, can be found [here](https://github.com/jmdaly/steamvan). + +Keyboard Maintainer: [jmdaly](https://github.com/jmdaly) +Hardware Supported: SteamVan PCB rev1 +Hardware Availability: Through group buys. + +Make example for this keyboard (after setting up your build environment): + + make handwired/steamvan/rev1:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/steamvan/rev1/chconf.h b/keyboards/handwired/steamvan/rev1/chconf.h new file mode 100644 index 0000000000..1d9f12ff1f --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/chconf.h @@ -0,0 +1,520 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 100000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 2 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 0 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM TRUE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT TRUE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY TRUE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS TRUE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK FALSE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS FALSE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS FALSE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK TRUE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS FALSE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/steamvan/rev1/config.h b/keyboards/handwired/steamvan/rev1/config.h new file mode 100644 index 0000000000..f10f42966b --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/config.h @@ -0,0 +1,70 @@ +/* +Copyright 2019 John M Daly <jmdaly@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER John M Daly +#define PRODUCT SteamVan rev1 +#define DESCRIPTION An open hardware forty percent PCB + +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here: + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + */ +#define STM32_BOOTLOADER_ADDRESS 0x1FFFD800 + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* ROWS: Top to bottom, COLS: Left to right +*/ +#define MATRIX_ROW_PINS { A6, A5, A4, A3 } +#define MATRIX_COL_PINS { A9, A8, B15, B14, B13, A10, B9, B6, B5, B4, B3, A15 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* Backlight configuration + * Backlight LEDs on B8 + */ +#define BACKLIGHT_LEVELS 24 +#define BACKLIGHT_BREATHING +#define BREATHING_PERIOD 6 + +#define RGBLIGHT_ANIMATIONS + +#define RGBLED_NUM 16 +#define RGB_DI_PIN A7 +#define DRIVER_LED_TOTAL RGBLED_NUM + +#define RGB_MATRIX_KEYPRESSES diff --git a/keyboards/handwired/steamvan/rev1/halconf.h b/keyboards/handwired/steamvan/rev1/halconf.h new file mode 100644 index 0000000000..5e5d70219e --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/halconf.h @@ -0,0 +1,388 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef HALCONF_H +#define HALCONF_H + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC TRUE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT TRUE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM TRUE +#endif + +/** + * @brief Enables the QSPI subsystem. + */ +#if !defined(HAL_USE_QSPI) || defined(__DOXYGEN__) +#define HAL_USE_QSPI FALSE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB TRUE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI FALSE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 16 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 256 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/** + * @brief Serial over USB number of buffers. + * @note The default is 2 buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_NUMBER) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_NUMBER 2 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* UART driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_WAIT) || defined(__DOXYGEN__) +#define UART_USE_WAIT FALSE +#endif + +/** + * @brief Enables the @p uartAcquireBus() and @p uartReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(UART_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define UART_USE_MUTUAL_EXCLUSION FALSE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* HALCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/steamvan/rev1/led.c b/keyboards/handwired/steamvan/rev1/led.c new file mode 100644 index 0000000000..1b78fa2f86 --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/led.c @@ -0,0 +1,242 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include "hal.h" +#include "led_custom.h" +#include "rev1.h" +#include "printf.h" + +static void breathing_callback(PWMDriver *pwmp); + +static PWMConfig pwmCFG = { + 0xFFFF, /* PWM clock frequency */ + 256, /* PWM period (in ticks) 1S (1/10kHz=0.1mS 0.1ms*10000 ticks=1S) */ + NULL, /* No Callback */ + { + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, /* Enable Channel 3 */ + {PWM_OUTPUT_DISABLED, NULL} + }, + 0, /* HW dependent part.*/ + 0 +}; + +static PWMConfig pwmCFG_breathing = { + 0xFFFF, /* 10kHz PWM clock frequency */ + 256, /* PWM period (in ticks) 1S (1/10kHz=0.1mS 0.1ms*10000 ticks=1S) */ + breathing_callback, /* Breathing Callback */ + { + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_DISABLED, NULL}, + {PWM_OUTPUT_ACTIVE_HIGH, NULL}, /* Enable Channel 3 */ + {PWM_OUTPUT_DISABLED, NULL} + }, + 0, /* HW dependent part.*/ + 0 +}; + +// See http://jared.geek.nz/2013/feb/linear-led-pwm +static uint16_t cie_lightness(uint16_t v) { + if (v <= 5243) // if below 8% of max + return v / 9; // same as dividing by 900% + else { + uint32_t y = (((uint32_t) v + 10486) << 8) / (10486 + 0xFFFFUL); // add 16% of max and compare + // to get a useful result with integer division, we shift left in the expression above + // and revert what we've done again after squaring. + y = y * y * y >> 8; + if (y > 0xFFFFUL) // prevent overflow + return 0xFFFFU; + else + return (uint16_t) y; + } +} + + +void backlight_init_ports(void) { + palSetPadMode(GPIOB, 8, PAL_MODE_ALTERNATE(2)); + pwmStart(&PWMD4, &pwmCFG); + if(kb_backlight_config.enable){ + if(kb_backlight_config.breathing){ + breathing_enable(); + } else{ + backlight_set(kb_backlight_config.level); + } + } else { + backlight_set(0); + } +} + +void backlight_set(uint8_t level) { + uint32_t duty = (uint32_t)(cie_lightness(0xFFFF * (uint32_t) level / BACKLIGHT_LEVELS)); + if (level == 0) { + // Turn backlight off + // Disable channel 3 on PWM4 + pwmDisableChannel(&PWMD4, 2); + } else { + // Turn backlight on + if(!is_breathing()){ + // Enable channel 3 on PWM4 + pwmEnableChannel(&PWMD4, 2, PWM_FRACTION_TO_WIDTH(&PWMD4,0xFFFF,duty)); + } + } +} + + +uint8_t backlight_tick = 0; + +void backlight_task(void) { +} + +#define BREATHING_NO_HALT 0 +#define BREATHING_HALT_OFF 1 +#define BREATHING_HALT_ON 2 +#define BREATHING_STEPS 128 + +static uint8_t breathing_period = BREATHING_PERIOD; +static uint8_t breathing_halt = BREATHING_NO_HALT; +static uint16_t breathing_counter = 0; + +bool is_breathing(void) { + return PWMD4.config == &pwmCFG_breathing; +} + +#define breathing_min() do {breathing_counter = 0;} while (0) +#define breathing_max() do {breathing_counter = breathing_period * 256 / 2;} while (0) + + +void breathing_interrupt_enable(void){ + pwmStop(&PWMD4); + pwmStart(&PWMD4, &pwmCFG_breathing); + chSysLockFromISR(); + pwmEnablePeriodicNotification(&PWMD4); + pwmEnableChannelI( + &PWMD4, + 2, + PWM_FRACTION_TO_WIDTH( + &PWMD4, + 0xFFFF, + 0xFFFF + ) + ); + chSysUnlockFromISR(); +} + +void breathing_interrupt_disable(void){ + pwmStop(&PWMD4); + pwmStart(&PWMD4, &pwmCFG); +} + +void breathing_enable(void) +{ + breathing_counter = 0; + breathing_halt = BREATHING_NO_HALT; + breathing_interrupt_enable(); +} + +void breathing_pulse(void) +{ + if (kb_backlight_config.level == 0) + breathing_min(); + else + breathing_max(); + breathing_halt = BREATHING_HALT_ON; + breathing_interrupt_enable(); +} + +void breathing_disable(void) +{ + breathing_interrupt_disable(); + // Restore backlight level + backlight_set(kb_backlight_config.level); +} + +void breathing_self_disable(void) +{ + if (kb_backlight_config.level == 0) + breathing_halt = BREATHING_HALT_OFF; + else + breathing_halt = BREATHING_HALT_ON; +} + +void breathing_toggle(void) { + if (is_breathing()){ + breathing_disable(); + } else { + breathing_enable(); + } +} + +void breathing_period_set(uint8_t value) +{ + if (!value) + value = 1; + breathing_period = value; +} + +void breathing_period_default(void) { + breathing_period_set(BREATHING_PERIOD); +} + +void breathing_period_inc(void) +{ + breathing_period_set(breathing_period+1); +} + +void breathing_period_dec(void) +{ + breathing_period_set(breathing_period-1); +} + +/* To generate breathing curve in python: + * from math import sin, pi; [int(sin(x/128.0*pi)**4*255) for x in range(128)] + */ +static const uint8_t breathing_table[BREATHING_STEPS] = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 3, 4, 5, 6, 8, 10, 12, 15, 17, 20, 24, 28, 32, 36, 41, 46, 51, 57, 63, 70, 76, 83, 91, 98, 106, 113, 121, 129, 138, 146, 154, 162, 170, 178, 185, 193, 200, 207, 213, 220, 225, 231, 235, 240, 244, 247, 250, 252, 253, 254, 255, 254, 253, 252, 250, 247, 244, 240, 235, 231, 225, 220, 213, 207, 200, 193, 185, 178, 170, 162, 154, 146, 138, 129, 121, 113, 106, 98, 91, 83, 76, 70, 63, 57, 51, 46, 41, 36, 32, 28, 24, 20, 17, 15, 12, 10, 8, 6, 5, 4, 3, 2, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; + +// Use this before the cie_lightness function. +static inline uint16_t scale_backlight(uint16_t v) { + return v / BACKLIGHT_LEVELS * kb_backlight_config.level; +} + +static void breathing_callback(PWMDriver *pwmp) +{ + (void)pwmp; + uint16_t interval = (uint16_t) breathing_period * 256 / BREATHING_STEPS; + // resetting after one period to prevent ugly reset at overflow. + breathing_counter = (breathing_counter + 1) % (breathing_period * 256); + uint8_t index = breathing_counter / interval % BREATHING_STEPS; + + if (((breathing_halt == BREATHING_HALT_ON) && (index == BREATHING_STEPS / 2)) || + ((breathing_halt == BREATHING_HALT_OFF) && (index == BREATHING_STEPS - 1))) + { + breathing_interrupt_disable(); + } + + uint32_t duty = cie_lightness(scale_backlight(breathing_table[index] * 256)); + + chSysLockFromISR(); + pwmEnableChannelI( + &PWMD4, + 2, + PWM_FRACTION_TO_WIDTH( + &PWMD4, + 0xFFFF, + duty + ) + ); + chSysUnlockFromISR(); +} diff --git a/keyboards/handwired/steamvan/rev1/led_custom.h b/keyboards/handwired/steamvan/rev1/led_custom.h new file mode 100644 index 0000000000..56e723db8f --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/led_custom.h @@ -0,0 +1,22 @@ +/* +Copyright 2019 John M Daly <jmdaly@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +void backlight_task(void); +void breathing_interrupt_disable(void); +void breathing_interrupt_enable(void); diff --git a/keyboards/handwired/steamvan/rev1/mcuconf.h b/keyboards/handwired/steamvan/rev1/mcuconf.h new file mode 100644 index 0000000000..69bf9185d1 --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/mcuconf.h @@ -0,0 +1,257 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef MCUCONF_H +#define MCUCONF_H + +/* + * STM32F3xx drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 15...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +#define STM32F3xx_MCUCONF + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 +#define STM32_HSI_ENABLED TRUE +#define STM32_LSI_ENABLED TRUE +#define STM32_HSE_ENABLED TRUE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSE +#define STM32_PREDIV_VALUE 1 +#define STM32_PLLMUL_VALUE 9 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE1 STM32_PPRE1_DIV2 +#define STM32_PPRE2 STM32_PPRE2_DIV2 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_ADC12PRES STM32_ADC12PRES_DIV1 +#define STM32_ADC34PRES STM32_ADC34PRES_DIV1 +#define STM32_USART1SW STM32_USART1SW_PCLK +#define STM32_USART2SW STM32_USART2SW_PCLK +#define STM32_USART3SW STM32_USART3SW_PCLK +#define STM32_UART4SW STM32_UART4SW_PCLK +#define STM32_UART5SW STM32_UART5SW_PCLK +#define STM32_I2C1SW STM32_I2C1SW_SYSCLK +#define STM32_I2C2SW STM32_I2C2SW_SYSCLK +#define STM32_TIM1SW STM32_TIM1SW_PCLK2 +#define STM32_TIM8SW STM32_TIM8SW_PCLK2 +#define STM32_RTCSEL STM32_RTCSEL_LSI +#define STM32_USB_CLOCK_REQUIRED TRUE +#define STM32_USBPRE STM32_USBPRE_DIV1P5 + +#undef STM32_HSE_BYPASS +// #error "oh no" +// #endif + +/* + * ADC driver system settings. + */ +#define STM32_ADC_DUAL_MODE FALSE +#define STM32_ADC_COMPACT_SAMPLES FALSE +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_USE_ADC2 FALSE +#define STM32_ADC_USE_ADC3 FALSE +#define STM32_ADC_USE_ADC4 FALSE +#define STM32_ADC_ADC1_DMA_STREAM STM32_DMA_STREAM_ID(1, 1) +#define STM32_ADC_ADC2_DMA_STREAM STM32_DMA_STREAM_ID(2, 1) +#define STM32_ADC_ADC3_DMA_STREAM STM32_DMA_STREAM_ID(2, 5) +#define STM32_ADC_ADC4_DMA_STREAM STM32_DMA_STREAM_ID(2, 2) +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_ADC2_DMA_PRIORITY 2 +#define STM32_ADC_ADC3_DMA_PRIORITY 2 +#define STM32_ADC_ADC4_DMA_PRIORITY 2 +#define STM32_ADC_ADC12_IRQ_PRIORITY 5 +#define STM32_ADC_ADC3_IRQ_PRIORITY 5 +#define STM32_ADC_ADC4_IRQ_PRIORITY 5 +#define STM32_ADC_ADC1_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC2_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC3_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC4_DMA_IRQ_PRIORITY 5 +#define STM32_ADC_ADC12_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1 +#define STM32_ADC_ADC34_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV1 + +/* + * CAN driver system settings. + */ +#define STM32_CAN_USE_CAN1 FALSE +#define STM32_CAN_CAN1_IRQ_PRIORITY 11 + +/* + * DAC driver system settings. + */ +#define STM32_DAC_DUAL_MODE FALSE +#define STM32_DAC_USE_DAC1_CH1 TRUE +#define STM32_DAC_USE_DAC1_CH2 TRUE +#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH1_DMA_PRIORITY 2 +#define STM32_DAC_DAC1_CH2_DMA_PRIORITY 2 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI20_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI21_22_29_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI30_32_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI33_IRQ_PRIORITY 6 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM4 FALSE +#define STM32_GPT_USE_TIM6 TRUE +#define STM32_GPT_USE_TIM7 TRUE +#define STM32_GPT_USE_TIM8 TRUE +#define STM32_GPT_TIM1_IRQ_PRIORITY 7 +#define STM32_GPT_TIM2_IRQ_PRIORITY 7 +#define STM32_GPT_TIM3_IRQ_PRIORITY 7 +#define STM32_GPT_TIM4_IRQ_PRIORITY 7 +#define STM32_GPT_TIM6_IRQ_PRIORITY 7 +#define STM32_GPT_TIM7_IRQ_PRIORITY 7 +#define STM32_GPT_TIM8_IRQ_PRIORITY 7 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 10 +#define STM32_I2C_I2C2_IRQ_PRIORITY 10 +#define STM32_I2C_USE_DMA TRUE +#define STM32_I2C_I2C1_DMA_PRIORITY 1 +#define STM32_I2C_I2C2_DMA_PRIORITY 1 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_USE_TIM4 FALSE +#define STM32_ICU_USE_TIM8 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 7 +#define STM32_ICU_TIM2_IRQ_PRIORITY 7 +#define STM32_ICU_TIM3_IRQ_PRIORITY 7 +#define STM32_ICU_TIM4_IRQ_PRIORITY 7 +#define STM32_ICU_TIM8_IRQ_PRIORITY 7 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_USE_TIM4 TRUE +#define STM32_PWM_USE_TIM8 FALSE +#define STM32_PWM_TIM1_IRQ_PRIORITY 7 +#define STM32_PWM_TIM2_IRQ_PRIORITY 7 +#define STM32_PWM_TIM3_IRQ_PRIORITY 7 +#define STM32_PWM_TIM4_IRQ_PRIORITY 7 +#define STM32_PWM_TIM8_IRQ_PRIORITY 7 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 TRUE +#define STM32_SERIAL_USE_USART3 FALSE +#define STM32_SERIAL_USE_UART4 FALSE +#define STM32_SERIAL_USE_UART5 FALSE +#define STM32_SERIAL_USART1_PRIORITY 12 +#define STM32_SERIAL_USART2_PRIORITY 12 +#define STM32_SERIAL_USART3_PRIORITY 12 +#define STM32_SERIAL_UART4_PRIORITY 12 +#define STM32_SERIAL_UART5_PRIORITY 12 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 FALSE +#define STM32_SPI_USE_SPI3 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI3_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 10 +#define STM32_SPI_SPI2_IRQ_PRIORITY 10 +#define STM32_SPI_SPI3_IRQ_PRIORITY 10 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 8 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USE_USART3 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 12 +#define STM32_UART_USART2_IRQ_PRIORITY 12 +#define STM32_UART_USART3_IRQ_PRIORITY 12 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_USART3_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_HP_IRQ_PRIORITY 13 +#define STM32_USB_USB1_LP_IRQ_PRIORITY 14 + +/* + * WDG driver system settings. + */ +#define STM32_WDG_USE_IWDG FALSE + +#endif /* MCUCONF_H */ diff --git a/keyboards/handwired/steamvan/rev1/rev1.c b/keyboards/handwired/steamvan/rev1/rev1.c new file mode 100644 index 0000000000..3188649494 --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/rev1.c @@ -0,0 +1,36 @@ +/* Copyright 2019 John M Daly <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "rev1.h" + +#include "led.h" +#include "printf.h" + +backlight_config_t kb_backlight_config = { + .enable = true, + .breathing = true, + .level = BACKLIGHT_LEVELS +}; + + + +void matrix_init_kb(void) { + matrix_init_user(); + backlight_init_ports(); +} + +void matrix_scan_kb(void) { + matrix_scan_user(); +} diff --git a/keyboards/handwired/steamvan/rev1/rev1.h b/keyboards/handwired/steamvan/rev1/rev1.h new file mode 100644 index 0000000000..83f7ecb9ca --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/rev1.h @@ -0,0 +1,90 @@ +/* Copyright 2019 Jack Humbert <jmdaly@gmail.com> + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" +#include "backlight.h" + +// This a shortcut to help you visually see your layout. +// There are a number of variations depending on the layout of your bottom row. +// The arrow variant adds an additional key on the bottom-right, while the +// command variant adds an additional key on the bottom-left. arrow-command is a +// combination of both of those, having an additional key on both sides. +// +// Please note that the numbering of the macro arguments are based on the +// numbers of the keys on the PCB. + +#define LAYOUT_standard( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ + K30, K31, K33, K34, K36, K38, K39, K3B \ +) \ +{ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ + { K30, K31, KC_NO, K33, K34, KC_NO, K36, KC_NO, K38, K39, KC_NO, K3B } \ +} + +#define LAYOUT_arrow( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ + K30, K31, K33, K34, K36, K38, K39, K3A, K3B \ +) \ +{ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ + { K30, K31, KC_NO, K33, K34, KC_NO, K36, KC_NO, K38, K39, K3A, K3B } \ +} + +#define LAYOUT_command( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ + K30, K31, K32, K33, K34, K36, K38, K39, K3B \ +) \ +{ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ + { K30, K31, K32, K33, K34, KC_NO, K36, KC_NO, K38, K39, KC_NO, K3B } \ +} + +#define LAYOUT_arrow_command( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ + K30, K31, K32, K33, K34, K36, K38, K39, K3A, K3B \ +) \ +{ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ + { K30, K31, K32, K33, K34, KC_NO, K36, KC_NO, K38, K39, K3A, K3B } \ +} + +// Backlighting +extern backlight_config_t kb_backlight_config; +extern bool kb_backlight_breathing; + +void backlight_init_ports(void); +void backlight_set(uint8_t level); +bool is_breathing(void); +void breathing_enable(void); +void breathing_disable(void); diff --git a/keyboards/handwired/steamvan/rev1/rules.mk b/keyboards/handwired/steamvan/rev1/rules.mk new file mode 100644 index 0000000000..471cb4c1e1 --- /dev/null +++ b/keyboards/handwired/steamvan/rev1/rules.mk @@ -0,0 +1,23 @@ +# MCU name +MCU = STM32F303 + +# Code for backlight breathing: +SRC += led.c + +# Build Options +# comment out to disable the options. +# +BACKLIGHT_ENABLE = yes +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality +MIDI_ENABLE = no # MIDI controls +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +LEADER_ENABLE = yes + diff --git a/keyboards/handwired/sticc14/config.h b/keyboards/handwired/sticc14/config.h new file mode 100644 index 0000000000..22011f0788 --- /dev/null +++ b/keyboards/handwired/sticc14/config.h @@ -0,0 +1,249 @@ +/* +Copyright 2019 ErkHal + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER u/ergorius +#define PRODUCT Sticc14 +#define DESCRIPTION Custom macropad + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 3 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * + */ +#define MATRIX_ROW_PINS { F4, F5, F6, F7, B1 } +#define MATRIX_COL_PINS { B6, B2, B3 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +/* + * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN. + */ +#define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6 + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + +// #define RGB_DI_PIN E2 +// #ifdef RGB_DI_PIN +// #define RGBLED_NUM 16 +// #define RGBLIGHT_HUE_STEP 8 +// #define RGBLIGHT_SAT_STEP 8 +// #define RGBLIGHT_VAL_STEP 8 +// #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ +// #define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ +// /*== all animations enable ==*/ +// #define RGBLIGHT_ANIMATIONS +// /*== or choose animations ==*/ +// #define RGBLIGHT_EFFECT_BREATHING +// #define RGBLIGHT_EFFECT_RAINBOW_MOOD +// #define RGBLIGHT_EFFECT_RAINBOW_SWIRL +// #define RGBLIGHT_EFFECT_SNAKE +// #define RGBLIGHT_EFFECT_KNIGHT +// #define RGBLIGHT_EFFECT_CHRISTMAS +// #define RGBLIGHT_EFFECT_STATIC_GRADIENT +// #define RGBLIGHT_EFFECT_RGB_TEST +// #define RGBLIGHT_EFFECT_ALTERNATING +// /*== customize breathing effect ==*/ +// /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ +// #define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 +// /*==== use exp() and sin() ====*/ +// #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 +// #define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 +// #endif + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +/* defined by default; to change, uncomment and set to the combination you want */ +// #define IS_COMMAND() (get_mods() == MOD_MASK_SHIFT) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP H +//#define MAGIC_KEY_HELP_ALT SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER0_ALT GRAVE +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER B +//#define MAGIC_KEY_BOOTLOADER_ALT ESC +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_EEPROM_CLEAR BSPACE +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + +/* + * HD44780 LCD Display Configuration + */ +/* +#define LCD_LINES 2 //< number of visible lines of the display +#define LCD_DISP_LENGTH 16 //< visibles characters per line of the display + +#define LCD_IO_MODE 1 //< 0: memory mapped mode, 1: IO port mode + +#if LCD_IO_MODE +#define LCD_PORT PORTB //< port for the LCD lines +#define LCD_DATA0_PORT LCD_PORT //< port for 4bit data bit 0 +#define LCD_DATA1_PORT LCD_PORT //< port for 4bit data bit 1 +#define LCD_DATA2_PORT LCD_PORT //< port for 4bit data bit 2 +#define LCD_DATA3_PORT LCD_PORT //< port for 4bit data bit 3 +#define LCD_DATA0_PIN 4 //< pin for 4bit data bit 0 +#define LCD_DATA1_PIN 5 //< pin for 4bit data bit 1 +#define LCD_DATA2_PIN 6 //< pin for 4bit data bit 2 +#define LCD_DATA3_PIN 7 //< pin for 4bit data bit 3 +#define LCD_RS_PORT LCD_PORT //< port for RS line +#define LCD_RS_PIN 3 //< pin for RS line +#define LCD_RW_PORT LCD_PORT //< port for RW line +#define LCD_RW_PIN 2 //< pin for RW line +#define LCD_E_PORT LCD_PORT //< port for Enable line +#define LCD_E_PIN 1 //< pin for Enable line +#endif +*/ + +/* Bootmagic Lite key configuration */ +// #define BOOTMAGIC_LITE_ROW 0 +// #define BOOTMAGIC_LITE_COLUMN 0 diff --git a/keyboards/handwired/sticc14/info.json b/keyboards/handwired/sticc14/info.json new file mode 100644 index 0000000000..fac5ab313e --- /dev/null +++ b/keyboards/handwired/sticc14/info.json @@ -0,0 +1,27 @@ +{ + "keyboard_name": "Sticc14", + "url": "", + "maintainer": "erkhal", + "width": 3, + "height": 5, + "layouts": { + "LAYOUT": { + "layout": [ + {"label":"K00", "x":0, "y":0}, + {"label":"K01", "x":1, "y":0}, + {"label":"K02", "x":2, "y":0}, + {"label":"K10", "x":0, "y":1}, + {"label":"K11", "x":1, "y":1}, + {"label":"K12", "x":2, "y":1}, + {"label":"K20", "x":0, "y":2}, + {"label":"K21", "x":1, "y":2}, + {"label":"K22", "x":2, "y":2}, + {"label":"K30", "x":0, "y":3}, + {"label":"K31", "x":1, "y":3}, + {"label":"K32", "x":2, "y":3}, + {"label":"K40", "x":0, "y":4, "w":2}, + {"label":"K41", "x":2, "y":4} + ] + } + } +} diff --git a/keyboards/handwired/sticc14/keymaps/default/config.h b/keyboards/handwired/sticc14/keymaps/default/config.h new file mode 100644 index 0000000000..0d34db1407 --- /dev/null +++ b/keyboards/handwired/sticc14/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 ErkHal + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/sticc14/keymaps/default/keymap.c b/keyboards/handwired/sticc14/keymaps/default/keymap.c new file mode 100644 index 0000000000..17364f0a22 --- /dev/null +++ b/keyboards/handwired/sticc14/keymaps/default/keymap.c @@ -0,0 +1,32 @@ +/* Copyright 2019 ErkHal + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT( /* Base */ + KC_PPLS, KC_PSLS, KC_BSPC, + KC_7, KC_8, KC_9, + KC_4, KC_5, KC_6, + KC_1, KC_2, KC_3, + KC_0, LT(1, KC_ENT)), + + [1] = LAYOUT( + KC_MPRV, KC_MPLY, KC_MNXT, + KC_TRNS, KC_TRNS, KC_TRNS, + KC_MPRV, KC_MPLY, KC_MNXT, + KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS) +}; diff --git a/keyboards/handwired/sticc14/keymaps/default/readme.md b/keyboards/handwired/sticc14/keymaps/default/readme.md new file mode 100644 index 0000000000..098402e68a --- /dev/null +++ b/keyboards/handwired/sticc14/keymaps/default/readme.md @@ -0,0 +1,5 @@ +# Default Sticc14 Layout + + + +Second layer has media keys on top-row. (Prev, Play/Pause, Next) diff --git a/keyboards/handwired/sticc14/readme.md b/keyboards/handwired/sticc14/readme.md new file mode 100644 index 0000000000..65f1a2416f --- /dev/null +++ b/keyboards/handwired/sticc14/readme.md @@ -0,0 +1,15 @@ +# Sticc14 + + + +Sticc14 is a simple macropad, designed to be easy to build and affordable. + +Keyboard Maintainer: [ErkHal](https://github.com/erkhal) +Hardware Supported: Sticc14 +Hardware Availability: [Ergorius](https://reddit.com/u/ergorius) + +Make example for this keyboard (after setting up your build environment): + + make handwired/sticc14:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/sticc14/rules.mk b/keyboards/handwired/sticc14/rules.mk new file mode 100644 index 0000000000..7b326cc319 --- /dev/null +++ b/keyboards/handwired/sticc14/rules.mk @@ -0,0 +1,32 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = caterina + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs diff --git a/keyboards/handwired/sticc14/sticc14.c b/keyboards/handwired/sticc14/sticc14.c new file mode 100644 index 0000000000..8edd2bda6b --- /dev/null +++ b/keyboards/handwired/sticc14/sticc14.c @@ -0,0 +1,51 @@ +/* Copyright 2019 ErkHal + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "sticc14.h" + +// Optional override functions below. +// You can leave any or all of these undefined. +// These are only required if you want to perform custom actions. + +/* + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} + +*/ diff --git a/keyboards/handwired/sticc14/sticc14.h b/keyboards/handwired/sticc14/sticc14.h new file mode 100644 index 0000000000..1a5f51e41a --- /dev/null +++ b/keyboards/handwired/sticc14/sticc14.h @@ -0,0 +1,40 @@ +/* Copyright 2019 ErkHal + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT( \ + K00, K01, K02, \ + K10, K11, K12, \ + K20, K21, K22, \ + K30, K31, K32, \ + K40, K41 \ +) { \ + { K00, K01, K02 }, \ + { K10, K11, K12 }, \ + { K20, K21, K22 }, \ + { K30, K31, K32 }, \ + { K40, K41} \ +} diff --git a/keyboards/handwired/symmetry60/config.h b/keyboards/handwired/symmetry60/config.h new file mode 100644 index 0000000000..ee72208afc --- /dev/null +++ b/keyboards/handwired/symmetry60/config.h @@ -0,0 +1,71 @@ +/* +Copyright 2019 Marhalloweenvt + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x0000 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Marhalloweenvt +#define PRODUCT Symmetry60 +#define DESCRIPTION A Boardwalk-inspired keyboard + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, C7, B6, B5, B4, D7, D6, D4, E6 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL*/ +#define DIODE_DIRECTION COL2ROW + +#define RGB_DI_PIN B1 +#ifdef RGB_DI_PIN +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 14 +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#endif + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCE 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE diff --git a/keyboards/handwired/symmetry60/info.json b/keyboards/handwired/symmetry60/info.json new file mode 100644 index 0000000000..f33c28b0c5 --- /dev/null +++ b/keyboards/handwired/symmetry60/info.json @@ -0,0 +1,83 @@ +{ + "Keyboard_name": "Symmetry60", + "url": "", + "maintainer": "marhalloweenvt", + "width": 14, + "height": 5, + "layouts": { + "LAYOUT_ortho_5x14": { + "layout": [ + {"label":"K00", "x":0, "y":0, "w":1.5}, + {"label":"K01", "x":1.5, "y":0}, + {"label":"K02", "x":2.5, "y":0}, + {"label":"K03", "x":3.5, "y":0}, + {"label":"K04", "x":4.5, "y":0}, + {"label":"K05", "x":5.5, "y":0}, + {"label":"K06", "x":6.5, "y":0}, + {"label":"K07", "x":7.5, "y":0}, + {"label":"K08", "x":8.5, "y":0}, + {"label":"K09", "x":9.5, "y":0}, + {"label":"K0A", "x":10.5, "y":0}, + {"label":"K0B", "x":11.5, "y":0}, + {"label":"K0C", "x":12.5, "y":0}, + {"label":"K0D", "x":13.5, "y":0, "w":1.5}, + {"label":"K10", "x":0, "y":1, "w":1.5}, + {"label":"K11", "x":1.5, "y":1}, + {"label":"K12", "x":2.5, "y":1}, + {"label":"K13", "x":3.5, "y":1}, + {"label":"K14", "x":4.5, "y":1}, + {"label":"K15", "x":5.5, "y":1}, + {"label":"K16", "x":6.5, "y":1}, + {"label":"K17", "x":7.5, "y":1}, + {"label":"K18", "x":8.5, "y":1}, + {"label":"K19", "x":9.5, "y":1}, + {"label":"K1A", "x":10.5, "y":1}, + {"label":"K1B", "x":11.5, "y":1}, + {"label":"K1C", "x":12.5, "y":1}, + {"label":"K1D", "x":13.5, "y":1, "w":1.5}, + {"label":"K20", "x":0, "y":2, "w":1.5}, + {"label":"K21", "x":1.5, "y":2}, + {"label":"K22", "x":2.5, "y":2}, + {"label":"K23", "x":3.5, "y":2}, + {"label":"K24", "x":4.5, "y":2}, + {"label":"K25", "x":5.5, "y":2}, + {"label":"K26", "x":6.5, "y":2}, + {"label":"K27", "x":7.5, "y":2}, + {"label":"K28", "x":8.5, "y":2}, + {"label":"K29", "x":9.5, "y":2}, + {"label":"K2A", "x":10.5, "y":2}, + {"label":"K2B", "x":11.5, "y":2}, + {"label":"K2C", "x":12.5, "y":2}, + {"label":"K2D", "x":13.5, "y":2, "w":1.5}, + {"label":"K30", "x":0, "y":3, "w":1.5}, + {"label":"K31", "x":1.5, "y":3}, + {"label":"K32", "x":2.5, "y":3}, + {"label":"K33", "x":3.5, "y":3}, + {"label":"K34", "x":4.5, "y":3}, + {"label":"K35", "x":5.5, "y":3}, + {"label":"K36", "x":6.5, "y":3}, + {"label":"K37", "x":7.5, "y":3}, + {"label":"K38", "x":8.5, "y":3}, + {"label":"K39", "x":9.5, "y":3}, + {"label":"K3A", "x":10.5, "y":3}, + {"label":"K3B", "x":11.5, "y":3}, + {"label":"K3C", "x":12.5, "y":3}, + {"label":"K3D", "x":13.5, "y":3, "w":1.5}, + {"label":"K40", "x":0, "y":4, "w":1.5}, + {"label":"K41", "x":1.5, "y":4}, + {"label":"K42", "x":2.5, "y":4}, + {"label":"K43", "x":3.5, "y":4}, + {"label":"K44", "x":4.5, "y":4}, + {"label":"K45", "x":5.5, "y":4}, + {"label":"K46", "x":6.5, "y":4}, + {"label":"K47", "x":7.5, "y":4}, + {"label":"K48", "x":8.5, "y":4}, + {"label":"K49", "x":9.5, "y":4}, + {"label":"K4A", "x":10.5, "y":4}, + {"label":"K4B", "x":11.5, "y":4}, + {"label":"K4C", "x":12.5, "y":4}, + {"label":"K4D", "x":13.5, "y":4, "w":1.5} + ] + } + } +} diff --git a/keyboards/handwired/symmetry60/keymaps/default/config.h b/keyboards/handwired/symmetry60/keymaps/default/config.h new file mode 100644 index 0000000000..7b52e1dd03 --- /dev/null +++ b/keyboards/handwired/symmetry60/keymaps/default/config.h @@ -0,0 +1,19 @@ +/* Copyright 2019 marhalloweenvt + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +// place overrides here diff --git a/keyboards/handwired/symmetry60/keymaps/default/keymap.c b/keyboards/handwired/symmetry60/keymaps/default/keymap.c new file mode 100644 index 0000000000..6960698951 --- /dev/null +++ b/keyboards/handwired/symmetry60/keymaps/default/keymap.c @@ -0,0 +1,26 @@ +/* Copyright 2019 marhalloweenvt + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = LAYOUT_ortho_5x14( + KC_GESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_MINS, KC_EQL, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_LBRC, KC_RBRC, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_QUOT, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_HOME, KC_PGUP, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_END, KC_PGDN, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, + KC_LCTL, KC_DEL, KC_LGUI, KC_LALT, KC_SPC, KC_SPC, KC_SPC, KC_SPC, KC_SPC, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, KC_RCTL + ), +}; diff --git a/keyboards/handwired/symmetry60/keymaps/default/readme.md b/keyboards/handwired/symmetry60/keymaps/default/readme.md new file mode 100644 index 0000000000..db25aa3bf2 --- /dev/null +++ b/keyboards/handwired/symmetry60/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default keymap for symmetry60 diff --git a/keyboards/handwired/symmetry60/readme.md b/keyboards/handwired/symmetry60/readme.md new file mode 100644 index 0000000000..5a4de934fe --- /dev/null +++ b/keyboards/handwired/symmetry60/readme.md @@ -0,0 +1,13 @@ +# SYMMETRY60 + +A keyboard inspired by Boardwalk + +* Keyboard Maintainer: [marhalloweenvt](https://github.com/marhalloweenvt) +* Hardware Supported: Symmetry60 PCB +* Hardware Availability: Symmetry60 PCB + +Make example for this keyboard (after setting up your build environment): + + make handwired/symmetry60:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). diff --git a/keyboards/handwired/symmetry60/rules.mk b/keyboards/handwired/symmetry60/rules.mk new file mode 100644 index 0000000000..6830cc6905 --- /dev/null +++ b/keyboards/handwired/symmetry60/rules.mk @@ -0,0 +1,36 @@ +# MCU name +MCU = atmega32u4 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs +LTO_ENABLE = yes # Use link time optimization + +LAYOUTS = ortho_5x14 diff --git a/keyboards/handwired/symmetry60/symmetry60.c b/keyboards/handwired/symmetry60/symmetry60.c new file mode 100644 index 0000000000..70828297c7 --- /dev/null +++ b/keyboards/handwired/symmetry60/symmetry60.c @@ -0,0 +1,16 @@ +/* Copyright 2019 marhalloweenvt + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#include "symmetry60.h" diff --git a/keyboards/handwired/symmetry60/symmetry60.h b/keyboards/handwired/symmetry60/symmetry60.h new file mode 100644 index 0000000000..138e5bb234 --- /dev/null +++ b/keyboards/handwired/symmetry60/symmetry60.h @@ -0,0 +1,42 @@ +/* Copyright 2019 marhalloweenvt + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ +#pragma once + +#include "quantum.h" + +/* This a shortcut to help you visually see your layout. + * + * The first section contains all of the arguments representing the physical + * layout of the board and position of the keys. + * + * The second converts the arguments into a two-dimensional array which + * represents the switch matrix. + */ +#define LAYOUT_ortho_5x14( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \ + K40, K41, K42, K43, K44, K45, K46, K47, K48, K49, K4A, K4B, K4C, K4D \ +) \ +{ \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D }, \ + { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D }, \ + { K40, K41, K42, K43, K44, K45, K46, K47, K48, K49, K4A, K4B, K4C, K4D }, \ +} + diff --git a/keyboards/handwired/tennie/rules.mk b/keyboards/handwired/tennie/rules.mk index 0119dc6fb2..b41b736a71 100644 --- a/keyboards/handwired/tennie/rules.mk +++ b/keyboards/handwired/tennie/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/handwired/terminus_mini/keymaps/default/keymap.c b/keyboards/handwired/terminus_mini/keymaps/default/keymap.c index 276475873a..78578a33ee 100644 --- a/keyboards/handwired/terminus_mini/keymaps/default/keymap.c +++ b/keyboards/handwired/terminus_mini/keymaps/default/keymap.c @@ -15,7 +15,6 @@ */ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. // The underscores don't mean anything - you can have a layer called STUFF or any other name. diff --git a/keyboards/handwired/terminus_mini/keymaps/default/rules.mk b/keyboards/handwired/terminus_mini/keymaps/default/rules.mk index 42ab51f150..a0c29684b1 100644 --- a/keyboards/handwired/terminus_mini/keymaps/default/rules.mk +++ b/keyboards/handwired/terminus_mini/keymaps/default/rules.mk @@ -1,19 +1,3 @@ -# Copyright 2013 Jun Wako <wakojun@gmail.com> -# -# This program is free software: you can redistribute it and/or modify -# it under the terms of the GNU General Public License as published by -# the Free Software Foundation, either version 2 of the License, or -# (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program. If not, see <http://www.gnu.org/licenses/>. - - # QMK Build Options # change to "no" to disable the options, or define them in the rules.mk in # the appropriate keymap folder that will get included automatically diff --git a/keyboards/handwired/terminus_mini/rules.mk b/keyboards/handwired/terminus_mini/rules.mk index 9ecba25d80..684da4cbb9 100644 --- a/keyboards/handwired/terminus_mini/rules.mk +++ b/keyboards/handwired/terminus_mini/rules.mk @@ -1,52 +1,15 @@ # MCU name -#MCU = at90usb1287 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay # Build Options # change yes to no to disable diff --git a/keyboards/handwired/trackpoint/rules.mk b/keyboards/handwired/trackpoint/rules.mk index 47dace8a22..668b3bb1ff 100644 --- a/keyboards/handwired/trackpoint/rules.mk +++ b/keyboards/handwired/trackpoint/rules.mk @@ -1,9 +1,17 @@ +# MCU name MCU = atmega32u4 -F_CPU = 16000000 -ARCH = AVR8 -F_USB = $(F_CPU) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT -OPT_DEFS += -DBOOTLOADER_SIZE=512 + +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = halfkay + + BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) @@ -19,4 +27,3 @@ AUDIO_ENABLE = no # Audio output on port C6 PS2_MOUSE_ENABLE = yes PS2_USE_USART = yes - diff --git a/keyboards/handwired/tradestation/rules.mk b/keyboards/handwired/tradestation/rules.mk index 649b63babf..d3612c3c29 100644 --- a/keyboards/handwired/tradestation/rules.mk +++ b/keyboards/handwired/tradestation/rules.mk @@ -1,54 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Boot Section Size in *bytes* -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # comment out to disable the options. # diff --git a/keyboards/handwired/traveller/keymaps/default/keymap.c b/keyboards/handwired/traveller/keymaps/default/keymap.c index 44f65f4b81..4802b05345 100644 --- a/keyboards/handwired/traveller/keymaps/default/keymap.c +++ b/keyboards/handwired/traveller/keymaps/default/keymap.c @@ -15,13 +15,13 @@ #define RGBLED_TOGGLE 10 #define _HIOUT 15 #define _LWOUT 16 -// Macros -#define MDL 4 -#define MDR 5 -#define MUR 6 -#define MUL 3 - +enum custom_keycodes { + M_MUL = SAFE_RANGE, + M_MDL, + M_MDR, + M_MUR +}; const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { /* Qwerty @@ -102,9 +102,9 @@ Right hand nav keys work pretty well chorded with the Right hand Hi Key */ [_NAV] = KEYMAP( - TG(_NAV), KC_NO, KC_NO, KC_UP, KC_NO, RGUI(KC_RIGHT), KC_WH_U, M(MUL), KC_MS_U, M(MUR), KC_NO, KC_ACL2, + TG(_NAV), KC_NO, KC_NO, KC_UP, KC_NO, RGUI(KC_RIGHT), KC_WH_U, M_MUL, KC_MS_U, M_MUR, KC_NO, KC_ACL2, KC_TRNS, RGUI(KC_LEFT), KC_LEFT, KC_DOWN, KC_RIGHT, LCTL(KC_E), KC_BTN3, KC_MS_L, KC_MS_U, KC_MS_R, KC_NO, KC_ACL1, - KC_TRNS, LCTL(KC_A), LGUI(KC_X),RGUI(KC_C), RGUI(KC_V),KC_NO, KC_ENTER, KC_WH_D, M(MDL), KC_MS_D, M(MDR), KC_UP, KC_ACL0, + KC_TRNS, LCTL(KC_A), LGUI(KC_X),RGUI(KC_C), RGUI(KC_V),KC_NO, KC_ENTER, KC_WH_D, M_MDL, KC_MS_D, M_MDR, KC_UP, KC_ACL0, KC_TRNS, RGUI(KC_Z), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_BTN2, KC_BTN1, KC_TRNS, KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT ), @@ -152,23 +152,10 @@ Right hand nav keys work pretty well chorded with the Right hand Hi Key }; -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - // MACRODOWN only works in this function - switch(id) { - case 0: - if (record->event.pressed) { - register_code(KC_RSFT); - #ifdef BACKLIGHT_ENABLE - backlight_step(); - #endif - } else { - unregister_code(KC_RSFT); - } - break; - +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { // from algernon's ErgoDox EZ layout, - case MUL: + case M_MUL: if (record->event.pressed) { mousekey_on(KC_MS_UP); mousekey_on(KC_MS_LEFT); @@ -177,9 +164,9 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) mousekey_off(KC_MS_LEFT); } mousekey_send(); - break; + return false; - case MUR: + case M_MUR: if (record->event.pressed) { mousekey_on(KC_MS_UP); mousekey_on(KC_MS_RIGHT); @@ -188,9 +175,9 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) mousekey_off(KC_MS_RIGHT); } mousekey_send(); - break; + return false; - case MDL: + case M_MDL: if (record->event.pressed) { mousekey_on(KC_MS_DOWN); mousekey_on(KC_MS_LEFT); @@ -199,9 +186,9 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) mousekey_off(KC_MS_LEFT); } mousekey_send(); - break; + return false; - case MDR: + case M_MDR: if (record->event.pressed) { mousekey_on(KC_MS_DOWN); mousekey_on(KC_MS_RIGHT); @@ -210,11 +197,11 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) mousekey_off(KC_MS_RIGHT); } mousekey_send(); - break; - - + return false; + default: + return true; } - return MACRO_NONE; + return true; }; void LayerLEDSet(uint8_t layr) { @@ -262,11 +249,6 @@ void matrix_scan_user(void) { } } - -bool process_record_user(uint16_t keycode, keyrecord_t *record) { - return true; -} - void led_set_user(uint8_t usb_led) { } diff --git a/keyboards/handwired/traveller/rules.mk b/keyboards/handwired/traveller/rules.mk index 8568def354..0758e59340 100644 --- a/keyboards/handwired/traveller/rules.mk +++ b/keyboards/handwired/traveller/rules.mk @@ -1,46 +1,14 @@ - -#MCU = at90usb1287 +# MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# for avr upload -USB = /dev/cu.usbmodem1421 -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp ifdef TEENSY2 BOOTLOADER = halfkay OPT_DEFS += -DATREUS_TEENSY2 @@ -52,23 +20,6 @@ else avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) endif - - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# MCU name - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # @@ -88,3 +39,5 @@ BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 RGBLIGHT_ENABLE = yes +# for avr upload +USB = /dev/cu.usbmodem1421 diff --git a/keyboards/handwired/tritium_numpad/rules.mk b/keyboards/handwired/tritium_numpad/rules.mk index c990a6ab14..42dfc5cbec 100644 --- a/keyboards/handwired/tritium_numpad/rules.mk +++ b/keyboards/handwired/tritium_numpad/rules.mk @@ -1,47 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # comment out to disable the options. # diff --git a/keyboards/handwired/woodpad/keymaps/default/rules.mk b/keyboards/handwired/woodpad/keymaps/default/rules.mk index fce19bfaa8..394bc0271f 100644 --- a/keyboards/handwired/woodpad/keymaps/default/rules.mk +++ b/keyboards/handwired/woodpad/keymaps/default/rules.mk @@ -1,19 +1,3 @@ -# Copyright 2013 Jun Wako <wakojun@gmail.com> -# -# This program is free software: you can redistribute it and/or modify -# it under the terms of the GNU General Public License as published by -# the Free Software Foundation, either version 2 of the License, or -# (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program. If not, see <http://www.gnu.org/licenses/>. - - # QMK Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -31,4 +15,3 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - diff --git a/keyboards/handwired/woodpad/rules.mk b/keyboards/handwired/woodpad/rules.mk index f8c488307f..7725131978 100644 --- a/keyboards/handwired/woodpad/rules.mk +++ b/keyboards/handwired/woodpad/rules.mk @@ -1,50 +1,16 @@ # MCU name -#MCU = at90usb1286 MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Build Options # change yes to no to disable # @@ -64,15 +30,3 @@ BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE ?= no # Audio output on port C6 FAUXCLICKY_ENABLE ?= no # Use buzzer to emulate clicky switches RGBLIGHT_ENABLE ?= no - -#avrdude: build -# ls /dev/tty* > /tmp/1; \ -# echo "Reset your Pro Micro now"; \ -# while [ -z $$USB ]; do \ -# sleep 1; \ -# ls /dev/tty* > /tmp/2; \ -# USB=`diff /tmp/1 /tmp/2 | $(GREP) -o '/dev/tty.*'`; \ -# done; \ -# avrdude -p $(MCU) -c avr109 -P $$USB -U flash:w:$(BUILD_DIR)/$(TARGET).hex -# -#.PHONY: avrdude diff --git a/keyboards/handwired/wulkan/rules.mk b/keyboards/handwired/wulkan/rules.mk index 3f881b7f12..f432c7d673 100644 --- a/keyboards/handwired/wulkan/rules.mk +++ b/keyboards/handwired/wulkan/rules.mk @@ -1,3 +1,4 @@ +# MCU name MCU = STM32F303 # Build Options diff --git a/keyboards/handwired/xealous/keymaps/default/keymap.c b/keyboards/handwired/xealous/keymaps/default/keymap.c index 4e691a0a76..ca82445a55 100644 --- a/keyboards/handwired/xealous/keymaps/default/keymap.c +++ b/keyboards/handwired/xealous/keymaps/default/keymap.c @@ -1,6 +1,5 @@ #include QMK_KEYBOARD_H -extern keymap_config_t keymap_config; // Each layer gets a name for readability, which is then used in the keymap matrix below. diff --git a/keyboards/handwired/xealous/matrix.c b/keyboards/handwired/xealous/matrix.c index e2d2199391..46410b986d 100644 --- a/keyboards/handwired/xealous/matrix.c +++ b/keyboards/handwired/xealous/matrix.c @@ -27,21 +27,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #include "util.h" #include "matrix.h" #include "split_util.h" -#include "pro_micro.h" #include "config.h" #include "timer.h" -#ifdef DEBUG_MATRIX_SCAN_RATE - #include "matrix_scanrate.h" -#endif - -void matrix_scan_user(void) -{ -#ifdef DEBUG_MATRIX_SCAN_RATE - matrix_check_scan_rate(); - matrix_time_between_scans(); -#endif - -} // Copy this code to split_common/matrix.c, // and call it instead of the unoptimized col_reader. Scan-rate jumps from 1200->1920 diff --git a/keyboards/handwired/xealous/matrix_scanrate.c b/keyboards/handwired/xealous/matrix_scanrate.c deleted file mode 100644 index f2c7cbe6e3..0000000000 --- a/keyboards/handwired/xealous/matrix_scanrate.c +++ /dev/null @@ -1,39 +0,0 @@ -#include <stdint.h> -#include <stdbool.h> -#include <avr/io.h> -#include "wait.h" -#include "print.h" -#include "debug.h" -#include "util.h" -#include "matrix.h" -#include "timer.h" - -#ifdef CONSOLE_ENABLE -static uint16_t matrix_scan_count = 0; -static uint32_t matrix_timer = 0; -void matrix_check_scan_rate(void) { - matrix_scan_count++; - if (matrix_scan_count > 1000) { - uint32_t timer_now = timer_read32(); - uint16_t ms_per_thousand = TIMER_DIFF_32(timer_now, matrix_timer); - uint16_t rate_per_second = 1000000UL / ms_per_thousand; - print("scan_rate: "); - pdec(rate_per_second); - print("\n"); - matrix_timer = timer_now; - matrix_scan_count = 0; - } -} - -static uint32_t last_scan_time = 0; -void matrix_time_between_scans(void) { - if (timer_elapsed(last_scan_time) > 1) - { - print(">1ms elapsed since last scan: "); - pdec(timer_elapsed(last_scan_time)); - print("\n"); - } - last_scan_time = timer_read(); - -} -#endif diff --git a/keyboards/handwired/xealous/matrix_scanrate.h b/keyboards/handwired/xealous/matrix_scanrate.h deleted file mode 100644 index 18d56cd5b4..0000000000 --- a/keyboards/handwired/xealous/matrix_scanrate.h +++ /dev/null @@ -1,4 +0,0 @@ -__attribute__((weak)) -void matrix_check_scan_rate(void) {} -__attribute__((weak)) -void matrix_time_between_scans(void) {} diff --git a/keyboards/handwired/xealous/rev1/rev1.h b/keyboards/handwired/xealous/rev1/rev1.h index d195af49de..0d8913b2ea 100644 --- a/keyboards/handwired/xealous/rev1/rev1.h +++ b/keyboards/handwired/xealous/rev1/rev1.h @@ -1,10 +1,8 @@ #ifndef REV1_H #define REV1_H -//void promicro_bootloader_jmp(bool program); #include "quantum.h" -//void promicro_bootloader_jmp(bool program); #define XXX KC_NO #define LAYOUT( \ diff --git a/keyboards/handwired/xealous/rules.mk b/keyboards/handwired/xealous/rules.mk index ef3357982e..2d816ab7ce 100644 --- a/keyboards/handwired/xealous/rules.mk +++ b/keyboards/handwired/xealous/rules.mk @@ -1,49 +1,16 @@ -SRC += matrix_scanrate.c matrix.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - # Build Options # change to "no" to disable the options, or define them in the Makefile in # the appropriate keymap folder that will get included automatically @@ -66,6 +33,7 @@ SUBPROJECT_rev1 = yes # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +SRC += matrix.c DEBOUNCE_TYPE = eager_pk LAYOUTS = split60 diff --git a/keyboards/handwired/xealousbrown/rules.mk b/keyboards/handwired/xealousbrown/rules.mk index 2bad9a1c6e..c346ef6c98 100644 --- a/keyboards/handwired/xealousbrown/rules.mk +++ b/keyboards/handwired/xealousbrown/rules.mk @@ -1,44 +1,16 @@ - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina + # Build Options # change yes to no to disable # @@ -56,5 +28,3 @@ MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 - - |