diff options
Diffstat (limited to 'keyboards/gh60/Makefile')
| -rw-r--r-- | keyboards/gh60/Makefile | 73 |
1 files changed, 1 insertions, 72 deletions
diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile index 075b77256f..57b2ef62e5 100644 --- a/keyboards/gh60/Makefile +++ b/keyboards/gh60/Makefile @@ -1,74 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -# CONSOLE_ENABLE ?= yes # Console for debug(+400) -# COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif - |