3 files changed, 13 insertions, 16 deletions

diff --git a/drivers/painter/comms/qp_comms_i2c.c b/drivers/painter/comms/qp_comms_i2c.c
index ec45ddfb3b..93f503f3dd 100644
--- a/drivers/painter/comms/qp_comms_i2c.c
+++ b/drivers/painter/comms/qp_comms_i2c.c
@@ -28,18 +28,14 @@ bool qp_comms_i2c_init(painter_device_t device) {
 }
 
 bool qp_comms_i2c_start(painter_device_t device) {
-    painter_driver_t *     driver       = (painter_driver_t *)device;
-    qp_comms_i2c_config_t *comms_config = (qp_comms_i2c_config_t *)driver->comms_config;
-    return i2c_start(comms_config->chip_address << 1) == I2C_STATUS_SUCCESS;
+    return true;
 }
 
 uint32_t qp_comms_i2c_send_data(painter_device_t device, const void *data, uint32_t byte_count) {
     return qp_comms_i2c_send_raw(device, data, byte_count);
 }
 
-void qp_comms_i2c_stop(painter_device_t device) {
-    i2c_stop();
-}
+void qp_comms_i2c_stop(painter_device_t device) {}
 
 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 // Command+Data I2C support
diff --git a/drivers/painter/comms/qp_comms_spi.c b/drivers/painter/comms/qp_comms_spi.c
index 9f52bc7d1f..4e6067394b 100644
--- a/drivers/painter/comms/qp_comms_spi.c
+++ b/drivers/painter/comms/qp_comms_spi.c
@@ -17,8 +17,8 @@ bool qp_comms_spi_init(painter_device_t device) {
     spi_init();
 
     // Set up CS as output high
-    setPinOutput(comms_config->chip_select_pin);
-    writePinHigh(comms_config->chip_select_pin);
+    gpio_set_pin_output(comms_config->chip_select_pin);
+    gpio_write_pin_high(comms_config->chip_select_pin);
 
     return true;
 }
@@ -49,7 +49,7 @@ void qp_comms_spi_stop(painter_device_t device) {
     painter_driver_t *     driver       = (painter_driver_t *)device;
     qp_comms_spi_config_t *comms_config = (qp_comms_spi_config_t *)driver->comms_config;
     spi_stop();
-    writePinHigh(comms_config->chip_select_pin);
+    gpio_write_pin_high(comms_config->chip_select_pin);
 }
 
 const painter_comms_vtable_t spi_comms_vtable = {
@@ -74,16 +74,16 @@ bool qp_comms_spi_dc_reset_init(painter_device_t device) {
 
     // Set up D/C as output low, if specified
     if (comms_config->dc_pin != NO_PIN) {
-        setPinOutput(comms_config->dc_pin);
-        writePinLow(comms_config->dc_pin);
+        gpio_set_pin_output(comms_config->dc_pin);
+        gpio_write_pin_low(comms_config->dc_pin);
     }
 
     // Set up RST as output, if specified, performing a reset in the process
     if (comms_config->reset_pin != NO_PIN) {
-        setPinOutput(comms_config->reset_pin);
-        writePinLow(comms_config->reset_pin);
+        gpio_set_pin_output(comms_config->reset_pin);
+        gpio_write_pin_low(comms_config->reset_pin);
         wait_ms(20);
-        writePinHigh(comms_config->reset_pin);
+        gpio_write_pin_high(comms_config->reset_pin);
         wait_ms(20);
     }
 
@@ -93,14 +93,14 @@ bool qp_comms_spi_dc_reset_init(painter_device_t device) {
 uint32_t qp_comms_spi_dc_reset_send_data(painter_device_t device, const void *data, uint32_t byte_count) {
     painter_driver_t *              driver       = (painter_driver_t *)device;
     qp_comms_spi_dc_reset_config_t *comms_config = (qp_comms_spi_dc_reset_config_t *)driver->comms_config;
-    writePinHigh(comms_config->dc_pin);
+    gpio_write_pin_high(comms_config->dc_pin);
     return qp_comms_spi_send_data(device, data, byte_count);
 }
 
 void qp_comms_spi_dc_reset_send_command(painter_device_t device, uint8_t cmd) {
     painter_driver_t *              driver       = (painter_driver_t *)device;
     qp_comms_spi_dc_reset_config_t *comms_config = (qp_comms_spi_dc_reset_config_t *)driver->comms_config;
-    writePinLow(comms_config->dc_pin);
+    gpio_write_pin_low(comms_config->dc_pin);
     spi_write(cmd);
 }
 
diff --git a/drivers/painter/comms/qp_comms_spi.h b/drivers/painter/comms/qp_comms_spi.h
index ff323c3c10..c39ea95f72 100644
--- a/drivers/painter/comms/qp_comms_spi.h
+++ b/drivers/painter/comms/qp_comms_spi.h
@@ -38,6 +38,7 @@ typedef struct qp_comms_spi_dc_reset_config_t {
     bool                  command_params_uses_command_pin; // keep D/C held low when sending command sequences for data bytes
 } qp_comms_spi_dc_reset_config_t;
 
+bool     qp_comms_spi_dc_reset_init(painter_device_t device);
 void     qp_comms_spi_dc_reset_send_command(painter_device_t device, uint8_t cmd);
 uint32_t qp_comms_spi_dc_reset_send_data(painter_device_t device, const void* data, uint32_t byte_count);
 void     qp_comms_spi_dc_reset_bulk_command_sequence(painter_device_t device, const uint8_t* sequence, size_t sequence_len);