Manual user keymap removal (#23104)

4 files changed, 0 insertions, 178 deletions

diff --git a/keyboards/wilba_tech/zeal60/keymaps/tusing/README.md b/keyboards/wilba_tech/zeal60/keymaps/tusing/README.md
deleted file mode 100644
index 1fbd745742..0000000000
--- a/keyboards/wilba_tech/zeal60/keymaps/tusing/README.md
+++ /dev/null
@@ -1,79 +0,0 @@
-# RGB Underglow Strip on the Zeal60: A Guide
-
-<img src="https://i.imgur.com/UuUdOCb.jpg" width="800">
-
-## Requirements
-
-- WS2812B RGB strip, preferably 60 LEDs/meter
-- Wire, solder
-- Tape, hot glue, or some sort of adhesive
-
-## A. Connecting the strip
-You might find the [**full PCB image**](https://cdn.shopify.com/s/files/1/0490/7329/files/zeal60jumpers.png) helpful. Ignore the red boxes!
-
-1. Connect V+ to the receiving end of the thermistor labeled F1; connect GND to the board's GND pin. (*Avoid connecting +V to the board's +5V pin* - you will likely overload the thermistor, and you will limit your maximum brightness.)
-
-    <img src="https://i.imgur.com/jd7qivh.png" width="300">
-
-2. Connect DI to PB0.
-
-    <img src="https://i.imgur.com/BiMyMLv.jpg" width="300">
-
-3. Should look something like this when finished:
-
-    <img src="https://i.imgur.com/ngxYMuA.jpg" width="600">
-
-*Optional:* To allow considerably more light to escape, consider angling the strip outwards by using some sort of fulcrum under the strip. (I used a thick wire.)
-
-## B. Enabling the strip
-1. If it is not present already, add the following to your ***keymap's*** ```Makefile```:
-
-    ```Makefile
-    RGBLIGHT_ENABLE = yes
-    AUDIO_ENABLE = no     #Underglow animations cannot be used with audio.
-    ```
-2. If it is not present already, add the following to your *keymap's* ```config.h```, and edit the values as necessary:
-
-    ```c
-    // Set up RGB underglow.
-    #define WS2812_DI_PIN B0          // The pin your RGB strip is wired to
-    #define RGBLED_NUM 35          // Number of LEDs
-    #define RGBLIGHT_HUE_STEP 5    // How much each press of rgb_hue changes hue
-    #define RGBLIGHT_SAT_STEP 10   // How much each press of rgb_sat changes sat
-    #define RGBLIGHT_VAL_STEP 10   // How much each press of rgb_val changes val
-    ```
-3. If they are not present already, add the following keycodes to your keymap to control the RGB strip: ```RGB_TOG``` (on/off), ```RGB_MOD``` (step through modes), ```RGB_HUI```, ```RGB_HUD```, ```RGB_SAI```, ```RGB_SAD```, ```RGB_VAI```, ```RGB_VAD``` (HSV increase/decrease). Add these to your keymap.
-
-## C. Dealing with current limits
-USB 2.0 ports on laptops provide up to 500mA max, but USB 3.0 ports can provide up to 900mA; USB 3.1 up to 1.5A; and powered USB hubs even more. We can run our keyboard at a higher brightness if we draw more power. **The Zeal60 uses 500mA at max brightness.** This means that **you have about 400mA remaining for the strip to use on a USB 3.0 port**; 1000mA free on a USB 3.1 port, so on and so forth.
-
-***Warning:*** **This means you will need to turn *off* your RGB strip before connecting to a USB 2.0 port**, as USB 2.0 cannot sustain the current necessary!
-
-1. If not present already, add the following to your keymap's ```config.h```. Change the numbers based on your needs. The ones below are safe underestimates.
-
-    ```c
-    // Enable current limiting for RGB underglow.
-    #define RGBSTRIP_CURRENT_LIMIT 400    // Strip current limit in mA. (USB amperage - 500mA for keyboard)
-    #define RGBSTRIP_MAX_CURRENT_PER_LIGHT 50 // mA per light when at max brightness.
-    ```
-    *Example:* I use a USB port capable of providing 1800 mA. The keyboard uses 500mA, so my personal value (in the `tusing` keymap) for `RGBSTRIP_CURRENT_LIMIT` is 1300. The particular WS2812B RGB strip I have uses a maximum of 60 mA per LED, so that is my personal value for `RGBSTRIP_MAX_CURRENT_PER_LIGHT`.
-2. Toggle on the LED strip (```RGB_TOG```) and step through animations (```RGB_MOD```) to test it out!
-
-## D. Sources and resources
-### A. Connecting the strip.
-* [In-depth description of connecting an RGB strip to the GH60](https://www.reddit.com/r/MechanicalKeyboards/comments/4d5or2/my_first_custom_build_satan_gh60_rbg_underglow_in/d1nz3o7/)
-* [32U4 Pinout](https://40.media.tumblr.com/93b6bbd4113418c2b45459bb177e67c5/tumblr_mi49a20QMB1s5t695o1_1280.png)
-* [Redditor describes connecting RGB strips on his Satan GH60](https://www.reddit.com/r/MechanicalKeyboards/comments/4hbjw4/finally_finished_my_satan_gh60_also_granite_o/d2qn8zx/?context=3)
-* [Another Redditor on RGB with the Satan GH60](https://www.reddit.com/r/MechanicalKeyboards/comments/4ewzdx/gh60_satan_with_the_rgb_mod/d251uu6/ )
-
-### B. Enabling the strip.
-* [QMK Wiki portion on underglow](https://github.com/jackhumbert/qmk_firmware/wiki#rgb-under-glow-mod)
-* [Planck ```Makefile```, ```config.h```, and ```keymap.c``` config example](https://github.com/jackhumbert/qmk_firmware/tree/master/keyboards/planck/keymaps/yang)
-* [Video demonstrating keycode functions and RGB modes on a KC60](https://www.youtube.com/watch?v=VKrpPAHlisY)
-
-### C. Dealing with current limits.
-* [Discussion of cutting jumpers and adding resistors to lower current from Zeal60](https://www.reddit.com/r/MechanicalKeyboards/comments/5hou92/photos_zeal60_lets_just_say_santa_came_early_this/db23qid/)
-* [A selection of 900mA-1.5A current hold fuses - look for an SMD 0805-sized fuse.](https://goo.gl/748avG)
-* [Video detailing technique to solder 0805 resistors](https://www.youtube.com/watch?v=PU7wLcuqc-I&t=123s&list=FLheMlKEVQ5cmVXazUt6HrxQ&index=2)
-* [QMK feature request to implement max power draw limits in ```config.h```](https://github.com/jackhumbert/qmk_firmware/issues/954)
-* [Commit enabling max power draw limits in ```config.h```](https://github.com/jackhumbert/qmk_firmware/commit/83e613ad239459582ae28f78b6c81535b9b138d7)
diff --git a/keyboards/wilba_tech/zeal60/keymaps/tusing/config.h b/keyboards/wilba_tech/zeal60/keymaps/tusing/config.h
deleted file mode 100644
index e797f81941..0000000000
--- a/keyboards/wilba_tech/zeal60/keymaps/tusing/config.h
+++ /dev/null
@@ -1,45 +0,0 @@
-#pragma once
-
-/* Enable/disable LEDs based on layout. */
-#undef RGB_BACKLIGHT_USE_SPLIT_BACKSPACE
-#define RGB_BACKLIGHT_USE_SPLIT_BACKSPACE 0
-
-#undef RGB_BACKLIGHT_USE_SPLIT_LEFT_SHIFT
-#define RGB_BACKLIGHT_USE_SPLIT_LEFT_SHIFT 0
-
-#undef RGB_BACKLIGHT_USE_SPLIT_RIGHT_SHIFT
-#define RGB_BACKLIGHT_USE_SPLIT_RIGHT_SHIFT 0
-
-#undef RGB_BACKLIGHT_USE_7U_SPACEBAR
-#define RGB_BACKLIGHT_USE_7U_SPACEBAR 0
-
-#undef RGB_BACKLIGHT_USE_ISO_ENTER
-#define RGB_BACKLIGHT_USE_ISO_ENTER 0
-
-#undef RGB_BACKLIGHT_DISABLE_HHKB_BLOCKER_LEDS
-#define RGB_BACKLIGHT_DISABLE_HHKB_BLOCKER_LEDS 0
-
-// Set up RGB underglow.
-#define WS2812_DI_PIN B0          // The pin your RGB strip is wired to
-#define RGBLIGHT_EFFECT_BREATHING
-#define RGBLIGHT_EFFECT_RAINBOW_MOOD
-#define RGBLIGHT_EFFECT_RAINBOW_SWIRL
-#define RGBLIGHT_EFFECT_SNAKE
-#define RGBLIGHT_EFFECT_KNIGHT
-#define RGBLIGHT_EFFECT_CHRISTMAS
-#define RGBLIGHT_EFFECT_STATIC_GRADIENT
-#define RGBLIGHT_EFFECT_RGB_TEST
-#define RGBLIGHT_EFFECT_ALTERNATING
-#define RGBLIGHT_EFFECT_TWINKLE
-#define RGBLED_NUM 35          // Number of LEDs
-#define RGBLIGHT_HUE_STEP 5    // How much each press of rgb_hue changes hue
-#define RGBLIGHT_SAT_STEP 10   // How much each press of rgb_sat changes sat
-#define RGBLIGHT_VAL_STEP 10   // How much each press of rgb_val changes val
-
-// Enable current limiting for RGB underglow.
-#define RGBSTRIP_CURRENT_LIMIT 1300    // Strip current limit in mA. (USB amperage - 500mA for keyboard)
-#define RGBSTRIP_MAX_CURRENT_PER_LIGHT 40 // mA per light when at max brightness.
-
-// Scale brightnes according to BRIGHTNESS_CORRECTION_TABLE in quantum/rgblight.c.
-// This allows to mitigate uneven brightness from LED underglow strips.
-// #define LED_BRIGHTNESS_CORRECTION
diff --git a/keyboards/wilba_tech/zeal60/keymaps/tusing/keymap.c b/keyboards/wilba_tech/zeal60/keymaps/tusing/keymap.c
deleted file mode 100644
index 21cb2cd73f..0000000000
--- a/keyboards/wilba_tech/zeal60/keymaps/tusing/keymap.c
+++ /dev/null
@@ -1,48 +0,0 @@
-// Default layout for Zeal60
-#include QMK_KEYBOARD_H
-
-// For readability.
-#define   _x_   KC_NO
-#define AUD_PRV LCTL(KC_MPRV) // Previous music track
-#define AUD_PLY LCTL(KC_MPLY) // Pause music
-#define AUD_NXT LCTL(KC_MNXT) // Next music track
-
-// Zeal60-specific keys:
-//  EF_INC, EF_DEC,   // next/previous backlight effect
-//  H1_INC, H1_DEC,   // Color 1 hue increase/decrease
-//  S1_INC, S1_DEC,   // Color 1 saturation increase/decrease
-//  H2_INC, H2_DEC,   // Color 2 hue increase/decrease
-//  S2_INC, S2_DEC,   // Color 2 saturation increase/decrease
-//  BR_INC, BR_DEC,   // backlight brightness increase/decrease
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-// Default layer: Pressing caps-lock momentarily switches to Layer 1.
-// This is the default layer. Pressing an empty keycode on another layer will take you here.
-    [0] = {
-        {KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  KC_BSPC},
-        {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, KC_BSLS},
-        {MO(1),   KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,    _x_  },
-        {KC_LSFT,   _x_  , KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT,   _x_  },
-        {KC_LCTL, KC_LGUI, KC_LALT,   _x_  ,   _x_  ,   _x_  ,   _x_  , KC_SPC,    _x_  ,   _x_  , KC_LEFT, KC_UP,   KC_DOWN, KC_RGHT}
-    },
-
-// Layer 1: Pressing enter switches to layer 2, where backlight controls live.
-// This is a momentary layer: once you let go of caps, you'll be back in layer 1.
-    [1] = {
-        {KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL },
-        {_______, KC_VOLD, KC_MUTE, KC_VOLU, _______, _______, _______, _______, KC_PSCR, KC_SCRL, KC_PAUS, KC_INS,  KC_DEL,  _______},
-        {_______, AUD_PRV, AUD_PLY, AUD_NXT, _______, _______, _______, _______, _______, _______, _______, _______, TO(2)  ,   _x_  },
-        {KC_CAPS,   _x_  , _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______,   _x_  },
-        {KC_RCTL, KC_RGUI, KC_RALT,   _x_  ,   _x_  ,   _x_  ,   _x_  , _______,   _x_  ,   _x_  , KC_HOME, KC_PGUP, KC_PGDN,  KC_END}
-    },
-
-// Layer 2: Zeal60 and backlight configuration. (Get here quickly by pressing Caps+Enter from Layer 1.)
-// This is a persistent layer. Get back to the default layer by pressing enter.
-    [2] = {
-        {QK_BOOT, EF_DEC,  EF_INC,  BR_DEC,  BR_INC,  ES_DEC,  ES_INC,  _______, _______, _______, _______, _______, _______, _______},
-        {_______, H1_DEC,  H1_INC,  S1_DEC,  S1_INC,  _______, _______, _______, _______, _______, _______, _______, _______, _______},
-        {_______, H2_DEC,  H2_INC,  S2_DEC,  S2_INC,  _______, _______, _______, _______, _______, _______, _______, TO(0)  ,   _x_  },
-        {RGB_MOD,   _x_  , RGB_HUD, RGB_HUI, RGB_SAD, RGB_SAI, _______, _______, _______, _______, _______, _______, _______,   _x_  },
-        {RGB_TOG, RGB_VAD, RGB_VAI,   _x_  ,   _x_  ,   _x_  ,   _x_  , _______,   _x_  ,   _x_  , _______, _______, _______, _______}
-    }
-};
diff --git a/keyboards/wilba_tech/zeal60/keymaps/tusing/rules.mk b/keyboards/wilba_tech/zeal60/keymaps/tusing/rules.mk
deleted file mode 100644
index 762905da03..0000000000
--- a/keyboards/wilba_tech/zeal60/keymaps/tusing/rules.mk
+++ /dev/null
@@ -1,6 +0,0 @@
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-RGBLIGHT_ENABLE = yes
-AUDIO_ENABLE = no  # Underglow cannot be used with audio.