diff options
author | zvecr <git@zvecr.com> | 2019-12-24 00:14:48 +0000 |
---|---|---|
committer | zvecr <git@zvecr.com> | 2020-01-26 23:33:03 +0000 |
commit | 98e55557052f30f4c621568247526cc4d5d41026 (patch) | |
tree | d8768bd3ff2dc0605b00efcafced44f759cc9c78 /keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103 | |
parent | d3abebb601e4e45f8c0b44c34d3c80dbf5bb9203 (diff) |
Remove duplicate board files
Diffstat (limited to 'keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103')
3 files changed, 0 insertions, 227 deletions
diff --git a/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.c b/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.c deleted file mode 100644 index 8c5a87f35f..0000000000 --- a/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.c +++ /dev/null @@ -1,56 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#include "hal.h" - -// Value to place in RTC backup register 10 for persistent bootloader mode -#define RTC_BOOTLOADER_FLAG 0x424C - -/** - * @brief PAL setup. - * @details Digital I/O ports static configuration as defined in @p board.h. - * This variable is used by the HAL when initializing the PAL driver. - */ -#if HAL_USE_PAL || defined(__DOXYGEN__) -const PALConfig pal_default_config = -{ - {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, - {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, - {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, - {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, - {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, -}; -#endif - -/* - * Early initialization code. - * This initialization must be performed just after stack setup and before - * any other initialization. - */ -void __early_init(void) { - - stm32_clock_init(); -} - -/* - * Board-specific initialization code. - */ -void boardInit(void) { - //JTAG-DP Disabled and SW-DP Enabled - AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE; - //Set backup register DR10 to enter bootloader on reset - BKP->DR10 = RTC_BOOTLOADER_FLAG; -} diff --git a/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.h b/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.h deleted file mode 100644 index 9427adabf1..0000000000 --- a/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.h +++ /dev/null @@ -1,166 +0,0 @@ -/* - ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio - - Licensed under the Apache License, Version 2.0 (the "License"); - you may not use this file except in compliance with the License. - You may obtain a copy of the License at - - http://www.apache.org/licenses/LICENSE-2.0 - - Unless required by applicable law or agreed to in writing, software - distributed under the License is distributed on an "AS IS" BASIS, - WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - See the License for the specific language governing permissions and - limitations under the License. -*/ - -#ifndef _BOARD_H_ -#define _BOARD_H_ - -/* - * Setup for a Generic STM32F103 board. - */ - -/* - * Board identifier. - */ -#define BOARD_GENERIC_STM32_F103 -#define BOARD_NAME "Generic STM32F103x board" - -/* - * Board frequencies. - */ -#define STM32_LSECLK 32768 -#define STM32_HSECLK 8000000 - -/* - * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. - */ -#define STM32F103xB - -/* - * IO pins assignments - */ - -/* on-board */ - -#define GPIOA_LED 8 -#define GPIOD_OSC_IN 0 -#define GPIOD_OSC_OUT 1 - -/* In case your board has a "USB enable" hardware - controlled by a pin, define it here. (It could be just - a 1.5k resistor connected to D+ line.) -*/ -/* -#define GPIOB_USB_DISC 10 -*/ - -/* - * I/O ports initial setup, this configuration is established soon after reset - * in the initialization code. - * - * The digits have the following meaning: - * 0 - Analog input. - * 1 - Push Pull output 10MHz. - * 2 - Push Pull output 2MHz. - * 3 - Push Pull output 50MHz. - * 4 - Digital input. - * 5 - Open Drain output 10MHz. - * 6 - Open Drain output 2MHz. - * 7 - Open Drain output 50MHz. - * 8 - Digital input with PullUp or PullDown resistor depending on ODR. - * 9 - Alternate Push Pull output 10MHz. - * A - Alternate Push Pull output 2MHz. - * B - Alternate Push Pull output 50MHz. - * C - Reserved. - * D - Alternate Open Drain output 10MHz. - * E - Alternate Open Drain output 2MHz. - * F - Alternate Open Drain output 50MHz. - * Please refer to the STM32 Reference Manual for details. - */ - -/* - * Port A setup. - * Everything input with pull-up except: - * PA2 - Alternate output (USART2 TX). - * PA3 - Normal input (USART2 RX). - * PA9 - Alternate output (USART1 TX). - * PA10 - Normal input (USART1 RX). - */ -#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */ -#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ -#define VAL_GPIOAODR 0xFFFFFFFF - -/* - * Port B setup. - * Everything input with pull-up except: - * PB10 - Push Pull output (USB switch). - */ -#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ -#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */ -#define VAL_GPIOBODR 0xFFFFFFFF - -/* - * Port C setup. - * Everything input with pull-up except: - * PC13 - Push Pull output (LED). - */ -#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ -#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */ -#define VAL_GPIOCODR 0xFFFFFFFF - -/* - * Port D setup. - * Everything input with pull-up except: - * PD0 - Normal input (XTAL). - * PD1 - Normal input (XTAL). - */ -#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ -#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ -#define VAL_GPIODODR 0xFFFFFFFF - -/* - * Port E setup. - * Everything input with pull-up except: - */ -#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ -#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ -#define VAL_GPIOEODR 0xFFFFFFFF - -/* - * USB bus activation macro, required by the USB driver. - */ -/* The point is that most of the generic STM32F103* boards - have a 1.5k resistor connected on one end to the D+ line - and on the other end to some pin. Or even a slightly more - complicated "USB enable" circuit, controlled by a pin. - That should go here. - - However on some boards (e.g. one that I have), there's no - such hardware. In which case it's better to not do anything. -*/ -/* -#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC) -*/ -#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT); - -/* - * USB bus de-activation macro, required by the USB driver. - */ -/* -#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC) -*/ -#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12); - -#if !defined(_FROM_ASM_) -#ifdef __cplusplus -extern "C" { -#endif - void boardInit(void); -#ifdef __cplusplus -} -#endif -#endif /* _FROM_ASM_ */ - -#endif /* _BOARD_H_ */ diff --git a/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.mk b/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.mk deleted file mode 100644 index 6b8b312fd9..0000000000 --- a/keyboards/cannonkeys/practice65/boards/GENERIC_STM32_F103/board.mk +++ /dev/null @@ -1,5 +0,0 @@ -# List of all the board related files. -BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F103/board.c - -# Required include directories -BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F103 |