1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
|
/*
* ----------------------------------------------------------------------------
* "THE BEER-WARE LICENSE" (Revision 42):
* <https://github.com/Legonut> wrote this file. As long as you retain this
* notice you can do whatever you want with this stuff. If we meet some day, and
* you think this stuff is worth it, you can buy me a beer in return. David Rauseo
* ----------------------------------------------------------------------------
*/
#pragma once
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0x3535
#define PRODUCT_ID 0x3505
#define MANUFACTURER RGBKB
#define PRODUCT Mün
#define USB_POLLING_INTERVAL_MS 1
/* Matrix Configuration - Rows are doubled up */
#define MATRIX_ROWS 14
// B1, A2 reserved for encoder / touch encoder support
#define MATRIX_ROW_PINS { A1, A3, B3, A13, B15, B1, A2 }
#define MATRIX_COLS 7
#define MATRIX_COL_PINS { A0, B11, B0, B10, B12, B2, A8 }
#define MATRIX_IO_DELAY 5
#define BUSY_WAIT
#define BUSY_WAIT_INSTRUCTIONS 35 // Increase if two rows are pressed at the same time.
#define GPIO_INPUT_PIN_DELAY 10
/* Touchbar adjustments */
#define TOUCH_DEADZONE 50 // width of a "button", wider inputs will be interpreted as a swipe
#define TOUCH_TERM 350 // time of a "button" touch, longer inputs will be a swipe
#define TOUCH_RESOLUTION 25 // sensitivity of swipes, lower=faster
/* Encoder Configuration */
#define ENCODERS_PAD_A { B8, B9 }
#define ENCODERS_PAD_B { A14, A15 }
#define TOUCH_SEGMENTS 3
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION COL2ROW
/* CRC Configuration */
#define CRC8_OPTIMIZE_SPEED
#define CRC8_USE_TABLE
/* Split Keyboard Configuration */
#define EE_HANDS
#define SPLIT_USB_DETECT
// also handles the SERIAL_USART_TX_PIN define
#define SOFT_SERIAL_PIN A9
#define SERIAL_USART_TX_PAL_MODE 7
#define SERIAL_USART_TIMEOUT 5
#define SERIAL_USART_DRIVER SD1
//#define SERIAL_USART_FULL_DUPLEX - Waiting on reunification pr
#if SERIAL_USART_FULL_DUPLEX
#define SERIAL_USART_RX_PIN A10
#define SERIAL_USART_RX_PAL_MODE 7
// Mun connects TX to TX and RX to RX as we were planning on i2c split, so we need pin swap for full duplex
#define SERIAL_USART_PIN_SWAP
#define SERIAL_USART_SPEED (2 * 1024 * 1024)
#else
#define SERIAL_USART_SPEED (1 * 1024 * 1024)
#endif
/* Split Transport Features */
#define SPLIT_TRANSPORT_MIRROR
#define SPLIT_LAYER_STATE_ENABLE
#define SPLIT_LED_STATE_ENABLE
#define SPLIT_TRANSACTION_IDS_KB TOUCH_ENCODER_SYNC, RGB_MENU_SYNC
/* RGB LED Configuration */
#define RGB_DI_PIN B5
#define RGBLED_NUM 98
#define RGBLED_SPLIT { 49, 49 }
#define RGBLIGHT_ANIMATIONS
#define DRIVER_LED_TOTAL RGBLED_NUM
#define RGB_MATRIX_SPLIT RGBLED_SPLIT
#define RGB_MATRIX_CENTER { 128, 34 }
#define RGB_MATRIX_LED_FLUSH_LIMIT 33
#define RGB_MATRIX_LED_PROCESS_LIMIT 10
#define RGB_MATRIX_KEYPRESSES
#define RGB_MATRIX_FRAMEBUFFER_EFFECTS
#define RGB_DISABLE_WHEN_USB_SUSPENDED
#if RGB_UNLIMITED_POWER
#define RGBLIGHT_LIMIT_VAL 255
#else
#define RGBLIGHT_LIMIT_VAL 127
#endif
#define RGB_MATRIX_MAXIMUM_BRIGHTNESS RGBLIGHT_LIMIT_VAL
#define WS2812_PWM_DRIVER PWMD3
#define WS2812_PWM_CHANNEL 2
#define WS2812_PWM_PAL_MODE 2
#define WS2812_DMA_STREAM STM32_DMA1_STREAM3
#define WS2812_DMA_CHANNEL 3
#define TOUCH_UPDATE_INTERVAL 33
#define OLED_UPDATE_INTERVAL 33
#define TAP_CODE_DELAY 5
|
