1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
|
#ifdef ISSI_ENABLE
#include <stdlib.h>
#include <stdint.h>
#include <util/delay.h>
#include <avr/sfr_defs.h>
#include <avr/io.h>
#include <util/twi.h>
#include "issi.h"
#include "print.h"
#include "TWIlib.h"
#define ISSI_ADDR_DEFAULT 0xE8
#define ISSI_REG_CONFIG 0x00
#define ISSI_REG_CONFIG_PICTUREMODE 0x00
#define ISSI_REG_CONFIG_AUTOPLAYMODE 0x08
#define ISSI_CONF_PICTUREMODE 0x00
#define ISSI_CONF_AUTOFRAMEMODE 0x04
#define ISSI_CONF_AUDIOMODE 0x08
#define ISSI_REG_PICTUREFRAME 0x01
#define ISSI_REG_SHUTDOWN 0x0A
#define ISSI_REG_AUDIOSYNC 0x06
#define ISSI_COMMANDREGISTER 0xFD
#define ISSI_BANK_FUNCTIONREG 0x0B // helpfully called 'page nine'
uint8_t control[8][9] = {
{0, 0, 0, 0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0, 0, 0, 0},
{0, 0, 0, 0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0, 0, 0, 0},
{0, 0, 0, 0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0, 0, 0, 0},
{0, 0, 0, 0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0, 0, 0, 0},
};
ISSIDeviceStruct *issi_devices[4] = {0, 0, 0, 0};
#ifndef cbi
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
#endif
#ifndef sbi
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
#endif
#define I2C_WRITE 0
#define F_SCL 400000UL // SCL frequency
#define Prescaler 1
#define TWBR_val ((((F_CPU / F_SCL) / Prescaler) - 16 ) / 2)
uint8_t i2c_start(uint8_t address)
{
// reset TWI control register
TWCR = 0;
// transmit START condition
TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
// wait for end of transmission
while( !(TWCR & (1<<TWINT)) );
// check if the start condition was successfully transmitted
if((TWSR & 0xF8) != TW_START){ return 1; }
// load slave address into data register
TWDR = address;
// start transmission of address
TWCR = (1<<TWINT) | (1<<TWEN);
// wait for end of transmission
while( !(TWCR & (1<<TWINT)) );
// check if the device has acknowledged the READ / WRITE mode
uint8_t twst = TW_STATUS & 0xF8;
if ( (twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK) ) return 1;
return 0;
}
uint8_t i2c_write(uint8_t data)
{
// load data into data register
TWDR = data;
// start transmission of data
TWCR = (1 << TWINT) | (1 << TWEN);
// wait for end of transmission
while (!(TWCR & (1 << TWINT)))
;
if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
return 1;
}
return 0;
}
uint8_t i2c_transmit(uint8_t address, uint8_t* data, uint16_t length)
{
TWBR = (uint8_t)TWBR_val;
if (i2c_start(address | I2C_WRITE))
return 1;
for (uint16_t i = 0; i < length; i++) {
if (i2c_write(data[i]))
return 1;
}
// transmit STOP condition
TWCR = (1 << TWINT) | (1 << TWEN) | (1 << TWSTO);
return 0;
}
void setFrame(uint8_t device, uint8_t frame)
{
static uint8_t current_frame = -1;
if(current_frame != frame){
uint8_t payload[] = {
ISSI_ADDR_DEFAULT | device << 1,
ISSI_COMMANDREGISTER,
frame
};
TWITransmitData(payload, sizeof(payload), 0, 1);
}
// static uint8_t current_frame = 0xFF;
// if(current_frame == frame){
// // return;
// }
// uint8_t payload[2] = { ISSI_COMMANDREGISTER, frame };
// i2c_transmit(ISSI_ADDR_DEFAULT | device << 1, payload, 2);
// current_frame = frame;
}
void writeRegister8(uint8_t device, uint8_t frame, uint8_t reg, uint8_t data)
{
// Set the frame
setFrame(device, frame);
// Write to the register
uint8_t payload[] = {
ISSI_ADDR_DEFAULT | device << 1,
reg,
data
};
TWITransmitData(payload, sizeof(payload), 0, 1);
}
void activateLED(uint8_t matrix, uint8_t cx, uint8_t cy, uint8_t pwm)
{
uint8_t device_addr = (matrix & 0x06) >> 1;
ISSIDeviceStruct *device = issi_devices[device_addr];
if(device == 0){
return;
}
// xprintf("activeLED: %02X %02X %02X %02X\n", matrix, cy, cx, pwm);
uint8_t x = cx - 1; // funciton takes 1 based counts, but we need 0...
uint8_t y = cy - 1; // creating them once for less confusion
uint8_t control_reg = (y << 1) | (matrix & 0x01);
if(pwm == 0){
cbi(device->led_ctrl[control_reg], x);
cbi(device->led_blink_ctrl[control_reg], x);
}else{
sbi(device->led_ctrl[control_reg], x);
sbi(device->led_blink_ctrl[control_reg], x);
}
uint8_t pwm_reg = 0;
switch(matrix & 0x01){
case 0:
pwm_reg = 0x00;
break;
case 1:
pwm_reg = 0x08;
break;
}
pwm_reg += (y << 4) + x;
device->led_pwm[pwm_reg] = pwm;
device->led_dirty = 1;
}
void update_issi(uint8_t device_addr, uint8_t blocking)
{
// This seems to take about 6ms
ISSIDeviceStruct *device = issi_devices[device_addr];
if(device != 0){
if(device->fn_dirty){
device->fn_dirty = 0;
setFrame(device_addr, ISSI_BANK_FUNCTIONREG);
TWITransmitData(&device->fn_device_addr, sizeof(device->fn_registers) + 2, 0, 1);
}
if(device->led_dirty){
device->led_dirty = 0;
setFrame(device_addr, 0);
TWITransmitData(&device->led_device_addr, 0xB6, 0, blocking);
}
}
}
void issi_init(void)
{
TWIInit();
for(uint8_t device_addr = 0; device_addr < 4; device_addr++){
// If this device has been previously allocated, free it
if(issi_devices[device_addr] != 0){
free(issi_devices[device_addr]);
}
// Try to shutdown the device, if this fails skip this device
writeRegister8(device_addr, ISSI_BANK_FUNCTIONREG, ISSI_REG_SHUTDOWN, 0x00);
while (!isTWIReady()){_delay_us(1);}
if(TWIInfo.errorCode != 0xFF){
xprintf("ISSI init failed %d %02X %02X\n", device_addr, TWIInfo.mode, TWIInfo.errorCode);
continue;
}
// Allocate the device structure - calloc zeros it for us
ISSIDeviceStruct *device = (ISSIDeviceStruct *)calloc(sizeof(ISSIDeviceStruct) * 2, 1);
issi_devices[device_addr] = device;
device->fn_device_addr = ISSI_ADDR_DEFAULT | device_addr << 1;
device->fn_register_addr = 0;
device->led_device_addr = ISSI_ADDR_DEFAULT | device_addr << 1;
device->led_register_addr = 0;
// set dirty bits so that all of the buffered data is written out
device->fn_dirty = 1;
device->led_dirty = 1;
update_issi(device_addr, 1);
// Set the function register to picture mode
// device->fn_reg[ISSI_REG_CONFIG] = ISSI_REG_CONFIG_PICTUREMODE;
writeRegister8(device_addr, ISSI_BANK_FUNCTIONREG, ISSI_REG_SHUTDOWN, 0x01);
}
// Shutdown and set all registers to 0
// writeRegister8(device_addr, ISSI_BANK_FUNCTIONREG, ISSI_REG_SHUTDOWN, 0x00);
// for(uint8_t bank = 0; bank <= 7; bank++){
// for (uint8_t reg = 0x00; reg <= 0xB3; reg++) {
// writeRegister8(device_addr, bank, reg, 0x00);
// }
// }
// for (uint8_t reg = 0; reg <= 0x0C; reg++) {
// writeRegister8(device_addr, ISSI_BANK_FUNCTIONREG, reg, 0x00);
// }
// writeRegister8(device_addr, ISSI_BANK_FUNCTIONREG, ISSI_REG_CONFIG, ISSI_REG_CONFIG_PICTUREMODE);
// writeRegister8(device_addr, ISSI_BANK_FUNCTIONREG, ISSI_REG_SHUTDOWN, 0x01);
// picture mode
// writeRegister8(ISSI_BANK_FUNCTIONREG, 0x01, 0x01);
//Enable blink
// writeRegister8(ISSI_BANK_FUNCTIONREG, 0x05, 0x48B);
//Enable Breath
}
#endif
|
