blob: 87ed40fabf20e321718416097608d99720b033a6 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
|
#include "infinity_ergodox.h"
#include "ch.h"
#include "hal.h"
#include "serial_link/system/serial_link.h"
#include "lcd_backlight.h"
void init_serial_link_hal(void) {
PORTA->PCR[1] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(2);
PORTA->PCR[2] = PORTx_PCRn_DSE | PORTx_PCRn_SRE | PORTx_PCRn_MUX(2);
PORTE->PCR[0] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(3);
PORTE->PCR[1] = PORTx_PCRn_DSE | PORTx_PCRn_SRE | PORTx_PCRn_MUX(3);
}
#define RED_PIN 1
#define GREEN_PIN 2
#define BLUE_PIN 3
#define CHANNEL_RED FTM0->CHANNEL[0]
#define CHANNEL_GREEN FTM0->CHANNEL[1]
#define CHANNEL_BLUE FTM0->CHANNEL[2]
#define RGB_PORT PORTC
#define RGB_PORT_GPIO GPIOC
// Base FTM clock selection (72 MHz system clock)
// @ 0xFFFF period, 72 MHz / (0xFFFF * 2) = Actual period
// Higher pre-scalar will use the most power (also look the best)
// Pre-scalar calculations
// 0 - 72 MHz -> 549 Hz
// 1 - 36 MHz -> 275 Hz
// 2 - 18 MHz -> 137 Hz
// 3 - 9 MHz -> 69 Hz (Slightly visible flicker)
// 4 - 4 500 kHz -> 34 Hz (Visible flickering)
// 5 - 2 250 kHz -> 17 Hz
// 6 - 1 125 kHz -> 9 Hz
// 7 - 562 500 Hz -> 4 Hz
// Using a higher pre-scalar without flicker is possible but FTM0_MOD will need to be reduced
// Which will reduce the brightness range
#define PRESCALAR_DEFINE 0
void lcd_backlight_hal_init(void) {
// Setup Backlight
SIM->SCGC6 |= SIM_SCGC6_FTM0;
FTM0->CNT = 0; // Reset counter
// PWM Period
// 16-bit maximum
FTM0->MOD = 0xFFFF;
// Set FTM to PWM output - Edge Aligned, Low-true pulses
#define CNSC_MODE FTM_SC_CPWMS | FTM_SC_PS(4) | FTM_SC_CLKS(0)
CHANNEL_RED.CnSC = CNSC_MODE;
CHANNEL_GREEN.CnSC = CNSC_MODE;
CHANNEL_BLUE.CnSC = CNSC_MODE;
// System clock, /w prescalar setting
FTM0->SC = FTM_SC_CLKS(1) | FTM_SC_PS(PRESCALAR_DEFINE);
CHANNEL_RED.CnV = 0;
CHANNEL_GREEN.CnV = 0;
CHANNEL_BLUE.CnV = 0;
RGB_PORT_GPIO->PDDR |= (1 << RED_PIN);
RGB_PORT_GPIO->PDDR |= (1 << GREEN_PIN);
RGB_PORT_GPIO->PDDR |= (1 << BLUE_PIN);
#define RGB_MODE PORTx_PCRn_SRE | PORTx_PCRn_DSE | PORTx_PCRn_MUX(4)
RGB_PORT->PCR[RED_PIN] = RGB_MODE;
RGB_PORT->PCR[GREEN_PIN] = RGB_MODE;
RGB_PORT->PCR[BLUE_PIN] = RGB_MODE;
}
void lcd_backlight_hal_color(uint16_t r, uint16_t g, uint16_t b) {
CHANNEL_RED.CnV = r;
CHANNEL_GREEN.CnV = g;
CHANNEL_BLUE.CnV = b;
}
|
