diff options
Diffstat (limited to 'tmk_core/protocol')
16 files changed, 2507 insertions, 2507 deletions
diff --git a/tmk_core/protocol/iwrap/suart.S b/tmk_core/protocol/iwrap/suart.S index 1b02909638..a873515e10 100644 --- a/tmk_core/protocol/iwrap/suart.S +++ b/tmk_core/protocol/iwrap/suart.S @@ -1,156 +1,156 @@ -;---------------------------------------------------------------------------;
-; Software implemented UART module ;
-; (C)ChaN, 2005 (http://elm-chan.org/) ;
-;---------------------------------------------------------------------------;
-; Bit rate settings:
-;
-; 1MHz 2MHz 4MHz 6MHz 8MHz 10MHz 12MHz 16MHz 20MHz
-; 2.4kbps 138 - - - - - - - -
-; 4.8kbps 68 138 - - - - - - -
-; 9.6kbps 33 68 138 208 - - - - -
-; 19.2kbps - 33 68 102 138 173 208 - -
-; 38.4kbps - - 33 50 68 85 102 138 172
-; 57.6kbps - - 21 33 44 56 68 91 114
-; 115.2kbps - - - - 21 27 33 44 56
-
-.nolist
-#include <avr/io.h>
-.list
-
-#define BPS 102 /* Bit delay. (see above table) */
-#define BIDIR 0 /* 0:Separated Tx/Rx, 1:Shared Tx/Rx */
-
-#define OUT_1 sbi _SFR_IO_ADDR(SUART_OUT_PORT), SUART_OUT_BIT /* Output 1 */
-#define OUT_0 cbi _SFR_IO_ADDR(SUART_OUT_PORT), SUART_OUT_BIT /* Output 0 */
-#define SKIP_IN_1 sbis _SFR_IO_ADDR(SUART_IN_PIN), SUART_IN_BIT /* Skip if 1 */
-#define SKIP_IN_0 sbic _SFR_IO_ADDR(SUART_IN_PIN), SUART_IN_BIT /* Skip if 0 */
-
-
-
-#ifdef SPM_PAGESIZE
-.macro _LPMI reg
- lpm \reg, Z+
-.endm
-.macro _MOVW dh,dl, sh,sl
- movw \dl, \sl
-.endm
-#else
-.macro _LPMI reg
- lpm
- mov \reg, r0
- adiw ZL, 1
-.endm
-.macro _MOVW dh,dl, sh,sl
- mov \dl, \sl
- mov \dh, \sh
-.endm
-#endif
-
-
-
-;---------------------------------------------------------------------------;
-; Transmit a byte in serial format of N81
-;
-;Prototype: void xmit (uint8_t data);
-;Size: 16 words
-
-.global xmit
-.func xmit
-xmit:
-#if BIDIR
- ldi r23, BPS-1 ;Pre-idle time for bidirectional data line
-5: dec r23 ;
- brne 5b ;/
-#endif
- in r0, _SFR_IO_ADDR(SREG) ;Save flags
-
- com r24 ;C = start bit
- ldi r25, 10 ;Bit counter
- cli ;Start critical section
-
-1: ldi r23, BPS-1 ;----- Bit transferring loop
-2: dec r23 ;Wait for a bit time
- brne 2b ;/
- brcs 3f ;MISO = bit to be sent
- OUT_1 ;
-3: brcc 4f ;
- OUT_0 ;/
-4: lsr r24 ;Get next bit into C
- dec r25 ;All bits sent?
- brne 1b ; no, coutinue
-
- out _SFR_IO_ADDR(SREG), r0 ;End of critical section
- ret
-.endfunc
-
-
-
-;---------------------------------------------------------------------------;
-; Receive a byte
-;
-;Prototype: uint8_t rcvr (void);
-;Size: 19 words
-
-.global rcvr
-.func rcvr
-rcvr:
- in r0, _SFR_IO_ADDR(SREG) ;Save flags
-
- ldi r24, 0x80 ;Receiving shift reg
- cli ;Start critical section
-
-1: SKIP_IN_1 ;Wait for idle
- rjmp 1b
-2: SKIP_IN_0 ;Wait for start bit
- rjmp 2b
- ldi r25, BPS/2 ;Wait for half bit time
-3: dec r25
- brne 3b
-
-4: ldi r25, BPS ;----- Bit receiving loop
-5: dec r25 ;Wait for a bit time
- brne 5b ;/
- lsr r24 ;Next bit
- SKIP_IN_0 ;Get a data bit into r24.7
- ori r24, 0x80
- brcc 4b ;All bits received? no, continue
-
- out _SFR_IO_ADDR(SREG), r0 ;End of critical section
- ret
-.endfunc
-
-
-; Not wait for start bit. This should be called after detecting start bit.
-.global recv
-.func recv
-recv:
- in r0, _SFR_IO_ADDR(SREG) ;Save flags
-
- ldi r24, 0x80 ;Receiving shift reg
- cli ;Start critical section
-
-;1: SKIP_IN_1 ;Wait for idle
-; rjmp 1b
-;2: SKIP_IN_0 ;Wait for start bit
-; rjmp 2b
- ldi r25, BPS/2 ;Wait for half bit time
-3: dec r25
- brne 3b
-
-4: ldi r25, BPS ;----- Bit receiving loop
-5: dec r25 ;Wait for a bit time
- brne 5b ;/
- lsr r24 ;Next bit
- SKIP_IN_0 ;Get a data bit into r24.7
- ori r24, 0x80
- brcc 4b ;All bits received? no, continue
-
- ldi r25, BPS/2 ;Wait for half bit time
-6: dec r25
- brne 6b
-7: SKIP_IN_1 ;Wait for stop bit
- rjmp 7b
-
- out _SFR_IO_ADDR(SREG), r0 ;End of critical section
- ret
-.endfunc
+;---------------------------------------------------------------------------; +; Software implemented UART module ; +; (C)ChaN, 2005 (http://elm-chan.org/) ; +;---------------------------------------------------------------------------; +; Bit rate settings: +; +; 1MHz 2MHz 4MHz 6MHz 8MHz 10MHz 12MHz 16MHz 20MHz +; 2.4kbps 138 - - - - - - - - +; 4.8kbps 68 138 - - - - - - - +; 9.6kbps 33 68 138 208 - - - - - +; 19.2kbps - 33 68 102 138 173 208 - - +; 38.4kbps - - 33 50 68 85 102 138 172 +; 57.6kbps - - 21 33 44 56 68 91 114 +; 115.2kbps - - - - 21 27 33 44 56 + +.nolist +#include <avr/io.h> +.list + +#define BPS 102 /* Bit delay. (see above table) */ +#define BIDIR 0 /* 0:Separated Tx/Rx, 1:Shared Tx/Rx */ + +#define OUT_1 sbi _SFR_IO_ADDR(SUART_OUT_PORT), SUART_OUT_BIT /* Output 1 */ +#define OUT_0 cbi _SFR_IO_ADDR(SUART_OUT_PORT), SUART_OUT_BIT /* Output 0 */ +#define SKIP_IN_1 sbis _SFR_IO_ADDR(SUART_IN_PIN), SUART_IN_BIT /* Skip if 1 */ +#define SKIP_IN_0 sbic _SFR_IO_ADDR(SUART_IN_PIN), SUART_IN_BIT /* Skip if 0 */ + + + +#ifdef SPM_PAGESIZE +.macro _LPMI reg + lpm \reg, Z+ +.endm +.macro _MOVW dh,dl, sh,sl + movw \dl, \sl +.endm +#else +.macro _LPMI reg + lpm + mov \reg, r0 + adiw ZL, 1 +.endm +.macro _MOVW dh,dl, sh,sl + mov \dl, \sl + mov \dh, \sh +.endm +#endif + + + +;---------------------------------------------------------------------------; +; Transmit a byte in serial format of N81 +; +;Prototype: void xmit (uint8_t data); +;Size: 16 words + +.global xmit +.func xmit +xmit: +#if BIDIR + ldi r23, BPS-1 ;Pre-idle time for bidirectional data line +5: dec r23 ; + brne 5b ;/ +#endif + in r0, _SFR_IO_ADDR(SREG) ;Save flags + + com r24 ;C = start bit + ldi r25, 10 ;Bit counter + cli ;Start critical section + +1: ldi r23, BPS-1 ;----- Bit transferring loop +2: dec r23 ;Wait for a bit time + brne 2b ;/ + brcs 3f ;MISO = bit to be sent + OUT_1 ; +3: brcc 4f ; + OUT_0 ;/ +4: lsr r24 ;Get next bit into C + dec r25 ;All bits sent? + brne 1b ; no, coutinue + + out _SFR_IO_ADDR(SREG), r0 ;End of critical section + ret +.endfunc + + + +;---------------------------------------------------------------------------; +; Receive a byte +; +;Prototype: uint8_t rcvr (void); +;Size: 19 words + +.global rcvr +.func rcvr +rcvr: + in r0, _SFR_IO_ADDR(SREG) ;Save flags + + ldi r24, 0x80 ;Receiving shift reg + cli ;Start critical section + +1: SKIP_IN_1 ;Wait for idle + rjmp 1b +2: SKIP_IN_0 ;Wait for start bit + rjmp 2b + ldi r25, BPS/2 ;Wait for half bit time +3: dec r25 + brne 3b + +4: ldi r25, BPS ;----- Bit receiving loop +5: dec r25 ;Wait for a bit time + brne 5b ;/ + lsr r24 ;Next bit + SKIP_IN_0 ;Get a data bit into r24.7 + ori r24, 0x80 + brcc 4b ;All bits received? no, continue + + out _SFR_IO_ADDR(SREG), r0 ;End of critical section + ret +.endfunc + + +; Not wait for start bit. This should be called after detecting start bit. +.global recv +.func recv +recv: + in r0, _SFR_IO_ADDR(SREG) ;Save flags + + ldi r24, 0x80 ;Receiving shift reg + cli ;Start critical section + +;1: SKIP_IN_1 ;Wait for idle +; rjmp 1b +;2: SKIP_IN_0 ;Wait for start bit +; rjmp 2b + ldi r25, BPS/2 ;Wait for half bit time +3: dec r25 + brne 3b + +4: ldi r25, BPS ;----- Bit receiving loop +5: dec r25 ;Wait for a bit time + brne 5b ;/ + lsr r24 ;Next bit + SKIP_IN_0 ;Get a data bit into r24.7 + ori r24, 0x80 + brcc 4b ;All bits received? no, continue + + ldi r25, BPS/2 ;Wait for half bit time +6: dec r25 + brne 6b +7: SKIP_IN_1 ;Wait for stop bit + rjmp 7b + + out _SFR_IO_ADDR(SREG), r0 ;End of critical section + ret +.endfunc diff --git a/tmk_core/protocol/iwrap/suart.h b/tmk_core/protocol/iwrap/suart.h index 72725b998f..7d92be0692 100644 --- a/tmk_core/protocol/iwrap/suart.h +++ b/tmk_core/protocol/iwrap/suart.h @@ -1,8 +1,8 @@ -#ifndef SUART
-#define SUART
-
-void xmit(uint8_t);
-uint8_t rcvr(void);
-uint8_t recv(void);
-
-#endif /* SUART */
+#ifndef SUART +#define SUART + +void xmit(uint8_t); +uint8_t rcvr(void); +uint8_t recv(void); + +#endif /* SUART */ diff --git a/tmk_core/protocol/iwrap/wd.h b/tmk_core/protocol/iwrap/wd.h index 99058f0331..12395bf696 100644 --- a/tmk_core/protocol/iwrap/wd.h +++ b/tmk_core/protocol/iwrap/wd.h @@ -1,159 +1,159 @@ -/* This is from http://www.mtcnet.net/~henryvm/wdt/ */
-#ifndef _AVR_WD_H_
-#define _AVR_WD_H_
-
-#include <avr/io.h>
-
-/*
-Copyright (c) 2009, Curt Van Maanen
-
-Permission to use, copy, modify, and/or distribute this software for any
-purpose with or without fee is hereby granted, provided that the above
-copyright notice and this permission notice appear in all copies.
-
-THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
-WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
-MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
-ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
-WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
-ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
-OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
-
-
-include usage-
- #include "wd.h" //if in same directory as project
- #include <avr/wd.h> //if wd.h is in avr directory
-
-set watchdog modes and prescale
-
-usage-
- WD_SET(mode,[timeout]); //prescale always set
-
-modes-
- WD_OFF disabled
- WD_RST normal reset mode
- WD_IRQ interrupt only mode (if supported)
- WD_RST_IRQ interrupt+reset mode (if supported)
-
-timeout-
- WDTO_15MS default if no timeout provided
- WDTO_30MS
- WDTO_60MS
- WDTO_120MS
- WDTO_250MS
- WDTO_500MS
- WDTO_1S
- WDTO_2S
- WDTO_4S (if supported)
- WDTO_8S (if supported)
-
-examples-
- WD_SET(WD_RST,WDTO_1S); //reset mode, 1s timeout
- WD_SET(WD_OFF); //watchdog disabled (if not fused on)
- WD_SET(WD_RST); //reset mode, 15ms (default timeout)
- WD_SET(WD_IRQ,WDTO_120MS); //interrupt only mode, 120ms timeout
- WD_SET(WD_RST_IRQ,WDTO_2S); //interrupt+reset mode, 2S timeout
-
-
-for enhanced watchdogs, if the watchdog is not being used WDRF should be
-cleared on every power up or reset, along with disabling the watchdog-
- WD_DISABLE(); //clear WDRF, then turn off watchdog
-
-*/
-
-//reset registers to the same name (MCUCSR)
-#if !defined(MCUCSR)
-#define MCUCSR MCUSR
-#endif
-
-//watchdog registers to the same name (WDTCSR)
-#if !defined(WDTCSR)
-#define WDTCSR WDTCR
-#endif
-
-//if enhanced watchdog, define irq values, create disable macro
-#if defined(WDIF)
-#define WD_IRQ 0xC0
-#define WD_RST_IRQ 0xC8
-#define WD_DISABLE() do{ \
- MCUCSR &= ~(1<<WDRF); \
- WD_SET(WD_OFF); \
- }while(0)
-#endif
-
-//all watchdogs
-#define WD_RST 8
-#define WD_OFF 0
-
-//prescale values
-#define WDTO_15MS 0
-#define WDTO_30MS 1
-#define WDTO_60MS 2
-#define WDTO_120MS 3
-#define WDTO_250MS 4
-#define WDTO_500MS 5
-#define WDTO_1S 6
-#define WDTO_2S 7
-
-//prescale values for avrs with WDP3
-#if defined(WDP3)
-#define WDTO_4S 0x20
-#define WDTO_8S 0x21
-#endif
-
-//watchdog reset
-#define WDR() __asm__ __volatile__("wdr")
-
-//avr reset using watchdog
-#define WD_AVR_RESET() do{ \
- __asm__ __volatile__("cli"); \
- WD_SET_UNSAFE(WD_RST); \
- while(1); \
- }while(0)
-
-/*set the watchdog-
-1. save SREG
-2. turn off irq's
-3. reset watchdog timer
-4. enable watchdog change
-5. write watchdog value
-6. restore SREG (restoring irq status)
-*/
-#define WD_SET(val,...) \
- __asm__ __volatile__( \
- "in __tmp_reg__,__SREG__" "\n\t" \
- "cli" "\n\t" \
- "wdr" "\n\t" \
- "sts %[wdreg],%[wden]" "\n\t" \
- "sts %[wdreg],%[wdval]" "\n\t" \
- "out __SREG__,__tmp_reg__" "\n\t" \
- : \
- : [wdreg] "M" (&WDTCSR), \
- [wden] "r" ((uint8_t)(0x18)), \
- [wdval] "r" ((uint8_t)(val|(__VA_ARGS__+0))) \
- : "r0" \
-)
-
-/*set the watchdog when I bit in SREG known to be clear-
-1. reset watchdog timer
-2. enable watchdog change
-5. write watchdog value
-*/
-#define WD_SET_UNSAFE(val,...) \
- __asm__ __volatile__( \
- "wdr" "\n\t" \
- "sts %[wdreg],%[wden]" "\n\t" \
- "sts %[wdreg],%[wdval]" "\n\t" \
- : \
- : [wdreg] "M" (&WDTCSR), \
- [wden] "r" ((uint8_t)(0x18)), \
- [wdval] "r" ((uint8_t)(val|(__VA_ARGS__+0))) \
-)
-
-
-//for compatibility with avr/wdt.h
-#define wdt_enable(val) WD_SET(WD_RST,val)
-#define wdt_disable() WD_SET(WD_OFF)
-
-
-#endif /* _AVR_WD_H_ */
+/* This is from http://www.mtcnet.net/~henryvm/wdt/ */ +#ifndef _AVR_WD_H_ +#define _AVR_WD_H_ + +#include <avr/io.h> + +/* +Copyright (c) 2009, Curt Van Maanen + +Permission to use, copy, modify, and/or distribute this software for any +purpose with or without fee is hereby granted, provided that the above +copyright notice and this permission notice appear in all copies. + +THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR +ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN +ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF +OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + + +include usage- + #include "wd.h" //if in same directory as project + #include <avr/wd.h> //if wd.h is in avr directory + +set watchdog modes and prescale + +usage- + WD_SET(mode,[timeout]); //prescale always set + +modes- + WD_OFF disabled + WD_RST normal reset mode + WD_IRQ interrupt only mode (if supported) + WD_RST_IRQ interrupt+reset mode (if supported) + +timeout- + WDTO_15MS default if no timeout provided + WDTO_30MS + WDTO_60MS + WDTO_120MS + WDTO_250MS + WDTO_500MS + WDTO_1S + WDTO_2S + WDTO_4S (if supported) + WDTO_8S (if supported) + +examples- + WD_SET(WD_RST,WDTO_1S); //reset mode, 1s timeout + WD_SET(WD_OFF); //watchdog disabled (if not fused on) + WD_SET(WD_RST); //reset mode, 15ms (default timeout) + WD_SET(WD_IRQ,WDTO_120MS); //interrupt only mode, 120ms timeout + WD_SET(WD_RST_IRQ,WDTO_2S); //interrupt+reset mode, 2S timeout + + +for enhanced watchdogs, if the watchdog is not being used WDRF should be +cleared on every power up or reset, along with disabling the watchdog- + WD_DISABLE(); //clear WDRF, then turn off watchdog + +*/ + +//reset registers to the same name (MCUCSR) +#if !defined(MCUCSR) +#define MCUCSR MCUSR +#endif + +//watchdog registers to the same name (WDTCSR) +#if !defined(WDTCSR) +#define WDTCSR WDTCR +#endif + +//if enhanced watchdog, define irq values, create disable macro +#if defined(WDIF) +#define WD_IRQ 0xC0 +#define WD_RST_IRQ 0xC8 +#define WD_DISABLE() do{ \ + MCUCSR &= ~(1<<WDRF); \ + WD_SET(WD_OFF); \ + }while(0) +#endif + +//all watchdogs +#define WD_RST 8 +#define WD_OFF 0 + +//prescale values +#define WDTO_15MS 0 +#define WDTO_30MS 1 +#define WDTO_60MS 2 +#define WDTO_120MS 3 +#define WDTO_250MS 4 +#define WDTO_500MS 5 +#define WDTO_1S 6 +#define WDTO_2S 7 + +//prescale values for avrs with WDP3 +#if defined(WDP3) +#define WDTO_4S 0x20 +#define WDTO_8S 0x21 +#endif + +//watchdog reset +#define WDR() __asm__ __volatile__("wdr") + +//avr reset using watchdog +#define WD_AVR_RESET() do{ \ + __asm__ __volatile__("cli"); \ + WD_SET_UNSAFE(WD_RST); \ + while(1); \ + }while(0) + +/*set the watchdog- +1. save SREG +2. turn off irq's +3. reset watchdog timer +4. enable watchdog change +5. write watchdog value +6. restore SREG (restoring irq status) +*/ +#define WD_SET(val,...) \ + __asm__ __volatile__( \ + "in __tmp_reg__,__SREG__" "\n\t" \ + "cli" "\n\t" \ + "wdr" "\n\t" \ + "sts %[wdreg],%[wden]" "\n\t" \ + "sts %[wdreg],%[wdval]" "\n\t" \ + "out __SREG__,__tmp_reg__" "\n\t" \ + : \ + : [wdreg] "M" (&WDTCSR), \ + [wden] "r" ((uint8_t)(0x18)), \ + [wdval] "r" ((uint8_t)(val|(__VA_ARGS__+0))) \ + : "r0" \ +) + +/*set the watchdog when I bit in SREG known to be clear- +1. reset watchdog timer +2. enable watchdog change +5. write watchdog value +*/ +#define WD_SET_UNSAFE(val,...) \ + __asm__ __volatile__( \ + "wdr" "\n\t" \ + "sts %[wdreg],%[wden]" "\n\t" \ + "sts %[wdreg],%[wdval]" "\n\t" \ + : \ + : [wdreg] "M" (&WDTCSR), \ + [wden] "r" ((uint8_t)(0x18)), \ + [wdval] "r" ((uint8_t)(val|(__VA_ARGS__+0))) \ +) + + +//for compatibility with avr/wdt.h +#define wdt_enable(val) WD_SET(WD_RST,val) +#define wdt_disable() WD_SET(WD_OFF) + + +#endif /* _AVR_WD_H_ */ diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/CDC/asf.xml b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/CDC/asf.xml index 72f3ff04c7..02e7063c66 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/CDC/asf.xml +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/CDC/asf.xml @@ -1,161 +1,161 @@ -<asf xmlversion="1.0">
- <project caption="CDC Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.128_4" force-caption="true" workspace-name="lufa_cdc_128kb_4kb_">
- <require idref="lufa.bootloaders.cdc"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb1287"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1F000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="CDC Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.64_4" force-caption="true" workspace-name="lufa_cdc_64kb_4kb_">
- <require idref="lufa.bootloaders.cdc"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb647"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0xF000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="CDC Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.32_4" force-caption="true" workspace-name="lufa_cdc_32kb_4kb_">
- <require idref="lufa.bootloaders.cdc"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega32u4"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x7000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="CDC Bootloader - 16KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.16_4" force-caption="true" workspace-name="lufa_cdc_16kb_4kb_">
- <require idref="lufa.bootloaders.cdc"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega16u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x3000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="CDC Bootloader - 8KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.8_4" force-caption="true" workspace-name="lufa_cdc_8kb_4kb_">
- <require idref="lufa.bootloaders.cdc"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega8u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <module type="application" id="lufa.bootloaders.cdc" caption="CDC Bootloader">
- <info type="description" value="summary">
- CDC Class Bootloader, capable of reprogramming a device using avrdude or other AVR109 protocol compliant software when plugged into a host.
- </info>
-
- <info type="gui-flag" value="move-to-root"/>
-
- <info type="keyword" value="Technology">
- <keyword value="Bootloaders"/>
- <keyword value="USB Device"/>
- </info>
-
- <device-support-alias value="lufa_avr8"/>
- <device-support-alias value="lufa_xmega"/>
- <device-support-alias value="lufa_uc3"/>
-
- <build type="include-path" value="."/>
- <build type="c-source" value="BootloaderCDC.c"/>
- <build type="header-file" value="BootloaderCDC.h"/>
- <build type="c-source" value="Descriptors.c"/>
- <build type="header-file" value="Descriptors.h"/>
- <build type="c-source" value="BootloaderAPI.c"/>
- <build type="header-file" value="BootloaderAPI.h"/>
- <build type="asm-source" value="BootloaderAPITable.S"/>
-
- <build type="module-config" subtype="path" value="Config"/>
- <build type="header-file" value="Config/LUFAConfig.h"/>
- <build type="header-file" value="Config/AppConfig.h"/>
-
- <build type="distribute" subtype="user-file" value="doxyfile"/>
- <build type="distribute" subtype="user-file" value="BootloaderCDC.txt"/>
- <build type="distribute" subtype="user-file" value="LUFA CDC Bootloader.inf"/>
-
- <require idref="lufa.common"/>
- <require idref="lufa.platform"/>
- <require idref="lufa.drivers.usb"/>
- <require idref="lufa.drivers.board"/>
- <require idref="lufa.drivers.board.leds"/>
- </module>
-</asf>
+<asf xmlversion="1.0"> + <project caption="CDC Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.128_4" force-caption="true" workspace-name="lufa_cdc_128kb_4kb_"> + <require idref="lufa.bootloaders.cdc"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb1287"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1F000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="CDC Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.64_4" force-caption="true" workspace-name="lufa_cdc_64kb_4kb_"> + <require idref="lufa.bootloaders.cdc"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb647"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0xF000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="CDC Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.32_4" force-caption="true" workspace-name="lufa_cdc_32kb_4kb_"> + <require idref="lufa.bootloaders.cdc"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega32u4"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x7000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="CDC Bootloader - 16KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.16_4" force-caption="true" workspace-name="lufa_cdc_16kb_4kb_"> + <require idref="lufa.bootloaders.cdc"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega16u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x3000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="CDC Bootloader - 8KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.cdc.avr8.8_4" force-caption="true" workspace-name="lufa_cdc_8kb_4kb_"> + <require idref="lufa.bootloaders.cdc"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega8u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <module type="application" id="lufa.bootloaders.cdc" caption="CDC Bootloader"> + <info type="description" value="summary"> + CDC Class Bootloader, capable of reprogramming a device using avrdude or other AVR109 protocol compliant software when plugged into a host. + </info> + + <info type="gui-flag" value="move-to-root"/> + + <info type="keyword" value="Technology"> + <keyword value="Bootloaders"/> + <keyword value="USB Device"/> + </info> + + <device-support-alias value="lufa_avr8"/> + <device-support-alias value="lufa_xmega"/> + <device-support-alias value="lufa_uc3"/> + + <build type="include-path" value="."/> + <build type="c-source" value="BootloaderCDC.c"/> + <build type="header-file" value="BootloaderCDC.h"/> + <build type="c-source" value="Descriptors.c"/> + <build type="header-file" value="Descriptors.h"/> + <build type="c-source" value="BootloaderAPI.c"/> + <build type="header-file" value="BootloaderAPI.h"/> + <build type="asm-source" value="BootloaderAPITable.S"/> + + <build type="module-config" subtype="path" value="Config"/> + <build type="header-file" value="Config/LUFAConfig.h"/> + <build type="header-file" value="Config/AppConfig.h"/> + + <build type="distribute" subtype="user-file" value="doxyfile"/> + <build type="distribute" subtype="user-file" value="BootloaderCDC.txt"/> + <build type="distribute" subtype="user-file" value="LUFA CDC Bootloader.inf"/> + + <require idref="lufa.common"/> + <require idref="lufa.platform"/> + <require idref="lufa.drivers.usb"/> + <require idref="lufa.drivers.board"/> + <require idref="lufa.drivers.board.leds"/> + </module> +</asf> diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/asf.xml b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/asf.xml index 6f3312b764..f56aba69f5 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/asf.xml +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/asf.xml @@ -1,156 +1,156 @@ -<asf xmlversion="1.0">
- <project caption="DFU Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.128_4" force-caption="true" workspace-name="lufa_dfu_128kb_4kb_">
- <require idref="lufa.bootloaders.dfu"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb1287"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1F000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="DFU Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.64_4" force-caption="true" workspace-name="lufa_dfu_64kb_4kb_">
- <require idref="lufa.bootloaders.dfu"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb647"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0xF000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="DFU Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.32_4" force-caption="true" workspace-name="lufa_dfu_32kb_4kb_">
- <require idref="lufa.bootloaders.dfu"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega32u4"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x7000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="DFU Bootloader - 16KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.16_4" force-caption="true" workspace-name="lufa_dfu_16kb_4kb_">
- <require idref="lufa.bootloaders.dfu"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega16u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x3000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="DFU Bootloader - 8KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.8_4" force-caption="true" workspace-name="lufa_dfu_8kb_4kb_">
- <require idref="lufa.bootloaders.dfu"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega8u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <module type="application" id="lufa.bootloaders.dfu" caption="DFU Bootloader">
- <info type="description" value="summary">
- DFU Class Bootloader, capable of reprogramming a device using the Atmel FLIP or other AVR DFU programming software when plugged into a host.
- </info>
-
- <info type="gui-flag" value="move-to-root"/>
-
- <info type="keyword" value="Technology">
- <keyword value="Bootloaders"/>
- <keyword value="USB Device"/>
- </info>
-
- <device-support-alias value="lufa_avr8"/>
- <device-support-alias value="lufa_xmega"/>
- <device-support-alias value="lufa_uc3"/>
-
- <build type="include-path" value="."/>
- <build type="c-source" value="BootloaderDFU.c"/>
- <build type="header-file" value="BootloaderDFU.h"/>
- <build type="c-source" value="Descriptors.c"/>
- <build type="header-file" value="Descriptors.h"/>
- <build type="c-source" value="BootloaderAPI.c"/>
- <build type="header-file" value="BootloaderAPI.h"/>
- <build type="asm-source" value="BootloaderAPITable.S"/>
-
- <build type="module-config" subtype="path" value="Config"/>
- <build type="header-file" value="Config/LUFAConfig.h"/>
- <build type="header-file" value="Config/AppConfig.h"/>
-
- <build type="distribute" subtype="user-file" value="doxyfile"/>
- <build type="distribute" subtype="user-file" value="BootloaderDFU.txt"/>
-
- <require idref="lufa.common"/>
- <require idref="lufa.platform"/>
- <require idref="lufa.drivers.usb"/>
- <require idref="lufa.drivers.board"/>
- <require idref="lufa.drivers.board.leds"/>
- </module>
-</asf>
+<asf xmlversion="1.0"> + <project caption="DFU Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.128_4" force-caption="true" workspace-name="lufa_dfu_128kb_4kb_"> + <require idref="lufa.bootloaders.dfu"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb1287"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1F000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="DFU Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.64_4" force-caption="true" workspace-name="lufa_dfu_64kb_4kb_"> + <require idref="lufa.bootloaders.dfu"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb647"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0xF000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="DFU Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.32_4" force-caption="true" workspace-name="lufa_dfu_32kb_4kb_"> + <require idref="lufa.bootloaders.dfu"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega32u4"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x7000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="DFU Bootloader - 16KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.16_4" force-caption="true" workspace-name="lufa_dfu_16kb_4kb_"> + <require idref="lufa.bootloaders.dfu"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega16u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x3000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="DFU Bootloader - 8KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.dfu.avr8.8_4" force-caption="true" workspace-name="lufa_dfu_8kb_4kb_"> + <require idref="lufa.bootloaders.dfu"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega8u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <module type="application" id="lufa.bootloaders.dfu" caption="DFU Bootloader"> + <info type="description" value="summary"> + DFU Class Bootloader, capable of reprogramming a device using the Atmel FLIP or other AVR DFU programming software when plugged into a host. + </info> + + <info type="gui-flag" value="move-to-root"/> + + <info type="keyword" value="Technology"> + <keyword value="Bootloaders"/> + <keyword value="USB Device"/> + </info> + + <device-support-alias value="lufa_avr8"/> + <device-support-alias value="lufa_xmega"/> + <device-support-alias value="lufa_uc3"/> + + <build type="include-path" value="."/> + <build type="c-source" value="BootloaderDFU.c"/> + <build type="header-file" value="BootloaderDFU.h"/> + <build type="c-source" value="Descriptors.c"/> + <build type="header-file" value="Descriptors.h"/> + <build type="c-source" value="BootloaderAPI.c"/> + <build type="header-file" value="BootloaderAPI.h"/> + <build type="asm-source" value="BootloaderAPITable.S"/> + + <build type="module-config" subtype="path" value="Config"/> + <build type="header-file" value="Config/LUFAConfig.h"/> + <build type="header-file" value="Config/AppConfig.h"/> + + <build type="distribute" subtype="user-file" value="doxyfile"/> + <build type="distribute" subtype="user-file" value="BootloaderDFU.txt"/> + + <require idref="lufa.common"/> + <require idref="lufa.platform"/> + <require idref="lufa.drivers.usb"/> + <require idref="lufa.drivers.board"/> + <require idref="lufa.drivers.board.leds"/> + </module> +</asf> diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/HID/asf.xml b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/HID/asf.xml index 9394b13530..c67b9419ed 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/HID/asf.xml +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/HID/asf.xml @@ -1,123 +1,123 @@ -<asf xmlversion="1.0">
- <project caption="HID Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.128_4" force-caption="true" workspace-name="lufa_hid_128kb_4kb_">
- <require idref="lufa.bootloaders.hid"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb1287"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1F000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/>
- </project>
-
- <project caption="HID Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.64_4" force-caption="true" workspace-name="lufa_hid_64kb_4kb_">
- <require idref="lufa.bootloaders.hid"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb647"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0xF000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/>
- </project>
-
- <project caption="HID Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.32_4" force-caption="true" workspace-name="lufa_hid_32kb_4kb_">
- <require idref="lufa.bootloaders.hid"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega32u4"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x7000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/>
- </project>
-
- <project caption="HID Bootloader - 16KB FLASH / 2KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.16_2" force-caption="true" workspace-name="lufa_hid_16kb_2kb_">
- <require idref="lufa.bootloaders.hid"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega16u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x3800"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x3800"/>
- </project>
-
- <project caption="HID Bootloader - 8KB FLASH / 2KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.8_2" force-caption="true" workspace-name="lufa_hid_8kb_2kb_">
- <require idref="lufa.bootloaders.hid"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega8u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1800"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1800"/>
- </project>
-
- <module type="application" id="lufa.bootloaders.hid" caption="HID Bootloader">
- <info type="description" value="summary">
- HID Class Bootloader, capable of reprogramming a device via a custom cross-platform command line utility when plugged into a host.
- </info>
-
- <info type="gui-flag" value="move-to-root"/>
-
- <info type="keyword" value="Technology">
- <keyword value="Bootloaders"/>
- <keyword value="USB Device"/>
- </info>
-
- <device-support-alias value="lufa_avr8"/>
- <device-support-alias value="lufa_xmega"/>
- <device-support-alias value="lufa_uc3"/>
-
- <build type="include-path" value="."/>
- <build type="c-source" value="BootloaderHID.c"/>
- <build type="header-file" value="BootloaderHID.h"/>
- <build type="c-source" value="Descriptors.c"/>
- <build type="header-file" value="Descriptors.h"/>
-
- <build type="module-config" subtype="path" value="Config"/>
- <build type="header-file" value="Config/LUFAConfig.h"/>
-
- <build type="distribute" subtype="user-file" value="doxyfile"/>
- <build type="distribute" subtype="user-file" value="BootloaderHID.txt"/>
- <build type="distribute" subtype="directory" value="HostLoaderApp"/>
- <build type="distribute" subtype="directory" value="HostLoaderApp_Python"/>
-
- <require idref="lufa.common"/>
- <require idref="lufa.platform"/>
- <require idref="lufa.drivers.usb"/>
- <require idref="lufa.drivers.board"/>
- <require idref="lufa.drivers.board.leds"/>
- </module>
-</asf>
+<asf xmlversion="1.0"> + <project caption="HID Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.128_4" force-caption="true" workspace-name="lufa_hid_128kb_4kb_"> + <require idref="lufa.bootloaders.hid"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb1287"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1F000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/> + </project> + + <project caption="HID Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.64_4" force-caption="true" workspace-name="lufa_hid_64kb_4kb_"> + <require idref="lufa.bootloaders.hid"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb647"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0xF000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/> + </project> + + <project caption="HID Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.32_4" force-caption="true" workspace-name="lufa_hid_32kb_4kb_"> + <require idref="lufa.bootloaders.hid"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega32u4"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x7000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/> + </project> + + <project caption="HID Bootloader - 16KB FLASH / 2KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.16_2" force-caption="true" workspace-name="lufa_hid_16kb_2kb_"> + <require idref="lufa.bootloaders.hid"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega16u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x3800"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x3800"/> + </project> + + <project caption="HID Bootloader - 8KB FLASH / 2KB Boot - AVR8 Architecture" id="lufa.bootloaders.hid.avr8.8_2" force-caption="true" workspace-name="lufa_hid_8kb_2kb_"> + <require idref="lufa.bootloaders.hid"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega8u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1800"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1800"/> + </project> + + <module type="application" id="lufa.bootloaders.hid" caption="HID Bootloader"> + <info type="description" value="summary"> + HID Class Bootloader, capable of reprogramming a device via a custom cross-platform command line utility when plugged into a host. + </info> + + <info type="gui-flag" value="move-to-root"/> + + <info type="keyword" value="Technology"> + <keyword value="Bootloaders"/> + <keyword value="USB Device"/> + </info> + + <device-support-alias value="lufa_avr8"/> + <device-support-alias value="lufa_xmega"/> + <device-support-alias value="lufa_uc3"/> + + <build type="include-path" value="."/> + <build type="c-source" value="BootloaderHID.c"/> + <build type="header-file" value="BootloaderHID.h"/> + <build type="c-source" value="Descriptors.c"/> + <build type="header-file" value="Descriptors.h"/> + + <build type="module-config" subtype="path" value="Config"/> + <build type="header-file" value="Config/LUFAConfig.h"/> + + <build type="distribute" subtype="user-file" value="doxyfile"/> + <build type="distribute" subtype="user-file" value="BootloaderHID.txt"/> + <build type="distribute" subtype="directory" value="HostLoaderApp"/> + <build type="distribute" subtype="directory" value="HostLoaderApp_Python"/> + + <require idref="lufa.common"/> + <require idref="lufa.platform"/> + <require idref="lufa.drivers.usb"/> + <require idref="lufa.drivers.board"/> + <require idref="lufa.drivers.board.leds"/> + </module> +</asf> diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderAPITable.S b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderAPITable.S index 6844d4b01c..91fc949666 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderAPITable.S +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderAPITable.S @@ -1,102 +1,102 @@ -/*
- LUFA Library
- Copyright (C) Dean Camera, 2014.
-
- dean [at] fourwalledcubicle [dot] com
- www.lufa-lib.org
-*/
-
-/*
- Copyright 2014 Dean Camera (dean [at] fourwalledcubicle [dot] com)
-
- Permission to use, copy, modify, distribute, and sell this
- software and its documentation for any purpose is hereby granted
- without fee, provided that the above copyright notice appear in
- all copies and that both that the copyright notice and this
- permission notice and warranty disclaimer appear in supporting
- documentation, and that the name of the author not be used in
- advertising or publicity pertaining to distribution of the
- software without specific, written prior permission.
-
- The author disclaims all warranties with regard to this
- software, including all implied warranties of merchantability
- and fitness. In no event shall the author be liable for any
- special, indirect or consequential damages or any damages
- whatsoever resulting from loss of use, data or profits, whether
- in an action of contract, negligence or other tortious action,
- arising out of or in connection with the use or performance of
- this software.
-*/
-
-#if AUX_BOOT_SECTION_SIZE > 0
-#warning Using a AUX bootloader section in addition to the defined bootloader space (see documentation).
-
-; Trampoline to jump over the AUX bootloader section to the start of the bootloader,
-; on devices where an AUX bootloader section is used.
-.section .boot_aux_trampoline, "ax"
-.global Boot_AUX_Trampoline
-Boot_AUX_Trampoline:
- jmp BOOT_START_ADDR
-#endif
-
-; Trampolines to actual API implementations if the target address is outside the
-; range of a rjmp instruction (can happen with large bootloader sections)
-.section .apitable_trampolines, "ax"
-.global BootloaderAPI_Trampolines
-BootloaderAPI_Trampolines:
-
- BootloaderAPI_ErasePage_Trampoline:
- jmp BootloaderAPI_ErasePage
- BootloaderAPI_WritePage_Trampoline:
- jmp BootloaderAPI_WritePage
- BootloaderAPI_FillWord_Trampoline:
- jmp BootloaderAPI_FillWord
- BootloaderAPI_ReadSignature_Trampoline:
- jmp BootloaderAPI_ReadSignature
- BootloaderAPI_ReadFuse_Trampoline:
- jmp BootloaderAPI_ReadFuse
- BootloaderAPI_ReadLock_Trampoline:
- jmp BootloaderAPI_ReadLock
- BootloaderAPI_WriteLock_Trampoline:
- jmp BootloaderAPI_WriteLock
- BootloaderAPI_UNUSED1:
- ret
- BootloaderAPI_UNUSED2:
- ret
- BootloaderAPI_UNUSED3:
- ret
- BootloaderAPI_UNUSED4:
- ret
- BootloaderAPI_UNUSED5:
- ret
-
-
-
-; API function jump table
-.section .apitable_jumptable, "ax"
-.global BootloaderAPI_JumpTable
-BootloaderAPI_JumpTable:
-
- rjmp BootloaderAPI_ErasePage_Trampoline
- rjmp BootloaderAPI_WritePage_Trampoline
- rjmp BootloaderAPI_FillWord_Trampoline
- rjmp BootloaderAPI_ReadSignature_Trampoline
- rjmp BootloaderAPI_ReadFuse_Trampoline
- rjmp BootloaderAPI_ReadLock_Trampoline
- rjmp BootloaderAPI_WriteLock_Trampoline
- rjmp BootloaderAPI_UNUSED1 ; UNUSED ENTRY 1
- rjmp BootloaderAPI_UNUSED2 ; UNUSED ENTRY 2
- rjmp BootloaderAPI_UNUSED3 ; UNUSED ENTRY 3
- rjmp BootloaderAPI_UNUSED4 ; UNUSED ENTRY 4
- rjmp BootloaderAPI_UNUSED5 ; UNUSED ENTRY 5
-
-
-
-; Bootloader table signatures and information
-.section .apitable_signatures, "ax"
-.global BootloaderAPI_Signatures
-BootloaderAPI_Signatures:
-
- .long BOOT_START_ADDR ; Start address of the bootloader
- .word 0xDF30 ; Signature for the MS class bootloader, V1
- .word 0xDCFB ; Signature for a LUFA class bootloader
+/* + LUFA Library + Copyright (C) Dean Camera, 2014. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2014 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaims all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +#if AUX_BOOT_SECTION_SIZE > 0 +#warning Using a AUX bootloader section in addition to the defined bootloader space (see documentation). + +; Trampoline to jump over the AUX bootloader section to the start of the bootloader, +; on devices where an AUX bootloader section is used. +.section .boot_aux_trampoline, "ax" +.global Boot_AUX_Trampoline +Boot_AUX_Trampoline: + jmp BOOT_START_ADDR +#endif + +; Trampolines to actual API implementations if the target address is outside the +; range of a rjmp instruction (can happen with large bootloader sections) +.section .apitable_trampolines, "ax" +.global BootloaderAPI_Trampolines +BootloaderAPI_Trampolines: + + BootloaderAPI_ErasePage_Trampoline: + jmp BootloaderAPI_ErasePage + BootloaderAPI_WritePage_Trampoline: + jmp BootloaderAPI_WritePage + BootloaderAPI_FillWord_Trampoline: + jmp BootloaderAPI_FillWord + BootloaderAPI_ReadSignature_Trampoline: + jmp BootloaderAPI_ReadSignature + BootloaderAPI_ReadFuse_Trampoline: + jmp BootloaderAPI_ReadFuse + BootloaderAPI_ReadLock_Trampoline: + jmp BootloaderAPI_ReadLock + BootloaderAPI_WriteLock_Trampoline: + jmp BootloaderAPI_WriteLock + BootloaderAPI_UNUSED1: + ret + BootloaderAPI_UNUSED2: + ret + BootloaderAPI_UNUSED3: + ret + BootloaderAPI_UNUSED4: + ret + BootloaderAPI_UNUSED5: + ret + + + +; API function jump table +.section .apitable_jumptable, "ax" +.global BootloaderAPI_JumpTable +BootloaderAPI_JumpTable: + + rjmp BootloaderAPI_ErasePage_Trampoline + rjmp BootloaderAPI_WritePage_Trampoline + rjmp BootloaderAPI_FillWord_Trampoline + rjmp BootloaderAPI_ReadSignature_Trampoline + rjmp BootloaderAPI_ReadFuse_Trampoline + rjmp BootloaderAPI_ReadLock_Trampoline + rjmp BootloaderAPI_WriteLock_Trampoline + rjmp BootloaderAPI_UNUSED1 ; UNUSED ENTRY 1 + rjmp BootloaderAPI_UNUSED2 ; UNUSED ENTRY 2 + rjmp BootloaderAPI_UNUSED3 ; UNUSED ENTRY 3 + rjmp BootloaderAPI_UNUSED4 ; UNUSED ENTRY 4 + rjmp BootloaderAPI_UNUSED5 ; UNUSED ENTRY 5 + + + +; Bootloader table signatures and information +.section .apitable_signatures, "ax" +.global BootloaderAPI_Signatures +BootloaderAPI_Signatures: + + .long BOOT_START_ADDR ; Start address of the bootloader + .word 0xDF30 ; Signature for the MS class bootloader, V1 + .word 0xDCFB ; Signature for a LUFA class bootloader diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/asf.xml b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/asf.xml index f1d550d1eb..700ffa26ff 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/asf.xml +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/asf.xml @@ -1,156 +1,156 @@ -<asf xmlversion="1.0">
- <project caption="Mass Storage Bootloader - 128KB FLASH / 8KB Boot - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.128_8" force-caption="true" workspace-name="lufa_ms_128kb_8kb_">
- <require idref="lufa.bootloaders.mass_storage"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb1287"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1E000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1E000"/>
-
- <build type="define" name="AUX_BOOT_SECTION_SIZE" value="0"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="Mass Storage Bootloader - 64KB FLASH / 8KB Boot - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.64_8" force-caption="true" workspace-name="lufa_ms_64kb_8kb_">
- <require idref="lufa.bootloaders.mass_storage"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb647"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0xE000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0xE000"/>
-
- <build type="define" name="AUX_BOOT_SECTION_SIZE" value="0"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="Mass Storage Bootloader - 32KB FLASH / 4KB Boot (2KB AUX) - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.32_4" force-caption="true" workspace-name="lufa_ms_32kb_4kb_">
- <require idref="lufa.bootloaders.mass_storage"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega32u4"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x7000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/>
-
- <build type="define" name="AUX_BOOT_SECTION_SIZE" value="2048"/>
- <build type="linker-config" subtype="flags" value="--section-start=.boot_aux=0x6810"/>
- <build type="linker-config" subtype="flags" value="--section-start=.boot_aux_trampoline=0x6800"/>
- <build type="linker-config" subtype="flags" value="--undefined=Boot_AUX_Trampoline"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="Mass Storage Bootloader - 16KB FLASH / 4KB Boot (2KB AUX) - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.16_4" force-caption="true" workspace-name="lufa_ms_16kb_4kb_">
- <require idref="lufa.bootloaders.mass_storage"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega16u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x3000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/>
-
- <build type="define" name="AUX_BOOT_SECTION_SIZE" value="2048"/>
- <build type="linker-config" subtype="flags" value="--section-start=.boot_aux=0x2810"/>
- <build type="linker-config" subtype="flags" value="--section-start=.boot_aux_trampoline=0x2800"/>
- <build type="linker-config" subtype="flags" value="--undefined=Boot_AUX_Trampoline"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <module type="application" id="lufa.bootloaders.mass_storage" caption="Mass Storage Bootloader">
- <info type="description" value="summary">
- Mass Storage Class Bootloader, capable of reprogramming a device via binary BIN files copied to the virtual FAT12 file-system it creates when plugged into a host.
- </info>
-
- <info type="gui-flag" value="move-to-root"/>
-
- <info type="keyword" value="Technology">
- <keyword value="Bootloaders"/>
- <keyword value="USB Device"/>
- </info>
-
- <device-support-alias value="lufa_avr8"/>
- <device-support-alias value="lufa_xmega"/>
- <device-support-alias value="lufa_uc3"/>
-
- <build type="include-path" value="."/>
- <build type="c-source" value="BootloaderMassStorage.c"/>
- <build type="header-file" value="BootloaderMassStorage.h"/>
- <build type="c-source" value="Descriptors.c"/>
- <build type="header-file" value="Descriptors.h"/>
- <build type="c-source" value="BootloaderAPI.c"/>
- <build type="header-file" value="BootloaderAPI.h"/>
- <build type="asm-source" value="BootloaderAPITable.S"/>
-
- <build type="module-config" subtype="path" value="Config"/>
- <build type="header-file" value="Config/LUFAConfig.h"/>
- <build type="header-file" value="Config/AppConfig.h"/>
-
- <build type="include-path" value="Lib"/>
- <build type="header-file" value="Lib/VirtualFAT.h"/>
- <build type="c-source" value="Lib/VirtualFAT.c"/>
- <build type="header-file" value="Lib/SCSI.h"/>
- <build type="c-source" value="Lib/SCSI.c"/>
-
- <build type="distribute" subtype="user-file" value="doxyfile"/>
- <build type="distribute" subtype="user-file" value="BootloaderMassStorage.txt"/>
-
- <require idref="lufa.common"/>
- <require idref="lufa.platform"/>
- <require idref="lufa.drivers.usb"/>
- <require idref="lufa.drivers.board"/>
- <require idref="lufa.drivers.board.leds"/>
- </module>
-</asf>
+<asf xmlversion="1.0"> + <project caption="Mass Storage Bootloader - 128KB FLASH / 8KB Boot - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.128_8" force-caption="true" workspace-name="lufa_ms_128kb_8kb_"> + <require idref="lufa.bootloaders.mass_storage"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb1287"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1E000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1E000"/> + + <build type="define" name="AUX_BOOT_SECTION_SIZE" value="0"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="Mass Storage Bootloader - 64KB FLASH / 8KB Boot - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.64_8" force-caption="true" workspace-name="lufa_ms_64kb_8kb_"> + <require idref="lufa.bootloaders.mass_storage"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb647"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0xE000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0xE000"/> + + <build type="define" name="AUX_BOOT_SECTION_SIZE" value="0"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="Mass Storage Bootloader - 32KB FLASH / 4KB Boot (2KB AUX) - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.32_4" force-caption="true" workspace-name="lufa_ms_32kb_4kb_"> + <require idref="lufa.bootloaders.mass_storage"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega32u4"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x7000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/> + + <build type="define" name="AUX_BOOT_SECTION_SIZE" value="2048"/> + <build type="linker-config" subtype="flags" value="--section-start=.boot_aux=0x6810"/> + <build type="linker-config" subtype="flags" value="--section-start=.boot_aux_trampoline=0x6800"/> + <build type="linker-config" subtype="flags" value="--undefined=Boot_AUX_Trampoline"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="Mass Storage Bootloader - 16KB FLASH / 4KB Boot (2KB AUX) - AVR8 Architecture" id="lufa.bootloaders.mass_storage.avr8.16_4" force-caption="true" workspace-name="lufa_ms_16kb_4kb_"> + <require idref="lufa.bootloaders.mass_storage"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega16u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x3000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/> + + <build type="define" name="AUX_BOOT_SECTION_SIZE" value="2048"/> + <build type="linker-config" subtype="flags" value="--section-start=.boot_aux=0x2810"/> + <build type="linker-config" subtype="flags" value="--section-start=.boot_aux_trampoline=0x2800"/> + <build type="linker-config" subtype="flags" value="--undefined=Boot_AUX_Trampoline"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <module type="application" id="lufa.bootloaders.mass_storage" caption="Mass Storage Bootloader"> + <info type="description" value="summary"> + Mass Storage Class Bootloader, capable of reprogramming a device via binary BIN files copied to the virtual FAT12 file-system it creates when plugged into a host. + </info> + + <info type="gui-flag" value="move-to-root"/> + + <info type="keyword" value="Technology"> + <keyword value="Bootloaders"/> + <keyword value="USB Device"/> + </info> + + <device-support-alias value="lufa_avr8"/> + <device-support-alias value="lufa_xmega"/> + <device-support-alias value="lufa_uc3"/> + + <build type="include-path" value="."/> + <build type="c-source" value="BootloaderMassStorage.c"/> + <build type="header-file" value="BootloaderMassStorage.h"/> + <build type="c-source" value="Descriptors.c"/> + <build type="header-file" value="Descriptors.h"/> + <build type="c-source" value="BootloaderAPI.c"/> + <build type="header-file" value="BootloaderAPI.h"/> + <build type="asm-source" value="BootloaderAPITable.S"/> + + <build type="module-config" subtype="path" value="Config"/> + <build type="header-file" value="Config/LUFAConfig.h"/> + <build type="header-file" value="Config/AppConfig.h"/> + + <build type="include-path" value="Lib"/> + <build type="header-file" value="Lib/VirtualFAT.h"/> + <build type="c-source" value="Lib/VirtualFAT.c"/> + <build type="header-file" value="Lib/SCSI.h"/> + <build type="c-source" value="Lib/SCSI.c"/> + + <build type="distribute" subtype="user-file" value="doxyfile"/> + <build type="distribute" subtype="user-file" value="BootloaderMassStorage.txt"/> + + <require idref="lufa.common"/> + <require idref="lufa.platform"/> + <require idref="lufa.drivers.usb"/> + <require idref="lufa.drivers.board"/> + <require idref="lufa.drivers.board.leds"/> + </module> +</asf> diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/makefile b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/makefile index 91bb4038e8..a0edb2c4f5 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/makefile +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/MassStorage/makefile @@ -1,68 +1,68 @@ -#
-# LUFA Library
-# Copyright (C) Dean Camera, 2014.
-#
-# dean [at] fourwalledcubicle [dot] com
-# www.lufa-lib.org
-#
-# --------------------------------------
-# LUFA Project Makefile.
-# --------------------------------------
-
-# Run "make help" for target help.
-
-MCU = at90usb1287
-ARCH = AVR8
-BOARD = USBKEY
-F_CPU = 8000000
-F_USB = $(F_CPU)
-OPTIMIZATION = s
-TARGET = BootloaderMassStorage
-SRC = $(TARGET).c Descriptors.c BootloaderAPI.c BootloaderAPITable.S Lib/SCSI.c Lib/VirtualFAT.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS)
-LUFA_PATH = ../../LUFA
-CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ -DBOOT_START_ADDR=$(BOOT_START_OFFSET)
-LD_FLAGS = -Wl,--section-start=.text=$(BOOT_START_OFFSET) $(BOOT_API_LD_FLAGS)
-
-# Flash size and bootloader section sizes of the target, in KB. These must
-# match the target's total FLASH size and the bootloader size set in the
-# device's fuses.
-FLASH_SIZE_KB = 128
-BOOT_SECTION_SIZE_KB = 8
-
-# Bootloader address calculation formulas
-# Do not modify these macros, but rather modify the dependent values above.
-CALC_ADDRESS_IN_HEX = $(shell printf "0x%X" $$(( $(1) )) )
-BOOT_START_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) - $(BOOT_SECTION_SIZE_KB)) * 1024 )
-BOOT_SEC_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) * 1024) - ($(strip $(1))) )
-
-# Bootloader linker section flags for relocating the API table sections to
-# known FLASH addresses - these should not normally be user-edited.
-BOOT_SECTION_LD_FLAG = -Wl,--section-start=$(strip $(1))=$(call BOOT_SEC_OFFSET, $(3)) -Wl,--undefined=$(strip $(2))
-BOOT_API_LD_FLAGS = $(call BOOT_SECTION_LD_FLAG, .apitable_trampolines, BootloaderAPI_Trampolines, 96)
-BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_jumptable, BootloaderAPI_JumpTable, 32)
-BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_signatures, BootloaderAPI_Signatures, 8)
-
-# Check if the bootloader needs an AUX section, located before the real bootloader section to store some of the
-# bootloader code. This is required for 32KB and smaller devices, where the actual bootloader is 6KB but the maximum
-# bootloader section size is 4KB. The actual usable application space will be reduced by 6KB for these devices.
-ifeq ($(BOOT_SECTION_SIZE_KB),8)
- CC_FLAGS += -DAUX_BOOT_SECTION_SIZE=0
-else
- AUX_BOOT_SECTION_SIZE_KB = (6 - $(BOOT_SECTION_SIZE_KB))
-
- CC_FLAGS += -DAUX_BOOT_SECTION_SIZE='($(AUX_BOOT_SECTION_SIZE_KB) * 1024)'
- LD_FLAGS += -Wl,--section-start=.boot_aux=$(call BOOT_SEC_OFFSET, (($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024 - 16))
- LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .boot_aux_trampoline, Boot_AUX_Trampoline, ($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024)
-endif
-
-# Default target
-all:
-
-# Include LUFA build script makefiles
-include $(LUFA_PATH)/Build/lufa_core.mk
-include $(LUFA_PATH)/Build/lufa_sources.mk
-include $(LUFA_PATH)/Build/lufa_build.mk
-include $(LUFA_PATH)/Build/lufa_cppcheck.mk
-include $(LUFA_PATH)/Build/lufa_doxygen.mk
-include $(LUFA_PATH)/Build/lufa_avrdude.mk
-include $(LUFA_PATH)/Build/lufa_atprogram.mk
+# +# LUFA Library +# Copyright (C) Dean Camera, 2014. +# +# dean [at] fourwalledcubicle [dot] com +# www.lufa-lib.org +# +# -------------------------------------- +# LUFA Project Makefile. +# -------------------------------------- + +# Run "make help" for target help. + +MCU = at90usb1287 +ARCH = AVR8 +BOARD = USBKEY +F_CPU = 8000000 +F_USB = $(F_CPU) +OPTIMIZATION = s +TARGET = BootloaderMassStorage +SRC = $(TARGET).c Descriptors.c BootloaderAPI.c BootloaderAPITable.S Lib/SCSI.c Lib/VirtualFAT.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS) +LUFA_PATH = ../../LUFA +CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ -DBOOT_START_ADDR=$(BOOT_START_OFFSET) +LD_FLAGS = -Wl,--section-start=.text=$(BOOT_START_OFFSET) $(BOOT_API_LD_FLAGS) + +# Flash size and bootloader section sizes of the target, in KB. These must +# match the target's total FLASH size and the bootloader size set in the +# device's fuses. +FLASH_SIZE_KB = 128 +BOOT_SECTION_SIZE_KB = 8 + +# Bootloader address calculation formulas +# Do not modify these macros, but rather modify the dependent values above. +CALC_ADDRESS_IN_HEX = $(shell printf "0x%X" $$(( $(1) )) ) +BOOT_START_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) - $(BOOT_SECTION_SIZE_KB)) * 1024 ) +BOOT_SEC_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) * 1024) - ($(strip $(1))) ) + +# Bootloader linker section flags for relocating the API table sections to +# known FLASH addresses - these should not normally be user-edited. +BOOT_SECTION_LD_FLAG = -Wl,--section-start=$(strip $(1))=$(call BOOT_SEC_OFFSET, $(3)) -Wl,--undefined=$(strip $(2)) +BOOT_API_LD_FLAGS = $(call BOOT_SECTION_LD_FLAG, .apitable_trampolines, BootloaderAPI_Trampolines, 96) +BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_jumptable, BootloaderAPI_JumpTable, 32) +BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_signatures, BootloaderAPI_Signatures, 8) + +# Check if the bootloader needs an AUX section, located before the real bootloader section to store some of the +# bootloader code. This is required for 32KB and smaller devices, where the actual bootloader is 6KB but the maximum +# bootloader section size is 4KB. The actual usable application space will be reduced by 6KB for these devices. +ifeq ($(BOOT_SECTION_SIZE_KB),8) + CC_FLAGS += -DAUX_BOOT_SECTION_SIZE=0 +else + AUX_BOOT_SECTION_SIZE_KB = (6 - $(BOOT_SECTION_SIZE_KB)) + + CC_FLAGS += -DAUX_BOOT_SECTION_SIZE='($(AUX_BOOT_SECTION_SIZE_KB) * 1024)' + LD_FLAGS += -Wl,--section-start=.boot_aux=$(call BOOT_SEC_OFFSET, (($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024 - 16)) + LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .boot_aux_trampoline, Boot_AUX_Trampoline, ($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024) +endif + +# Default target +all: + +# Include LUFA build script makefiles +include $(LUFA_PATH)/Build/lufa_core.mk +include $(LUFA_PATH)/Build/lufa_sources.mk +include $(LUFA_PATH)/Build/lufa_build.mk +include $(LUFA_PATH)/Build/lufa_cppcheck.mk +include $(LUFA_PATH)/Build/lufa_doxygen.mk +include $(LUFA_PATH)/Build/lufa_avrdude.mk +include $(LUFA_PATH)/Build/lufa_atprogram.mk diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/BootloaderAPITable.S b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/BootloaderAPITable.S index ec499b74e5..88c51da825 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/BootloaderAPITable.S +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/BootloaderAPITable.S @@ -1,91 +1,91 @@ -/*
- LUFA Library
- Copyright (C) Dean Camera, 2014.
-
- dean [at] fourwalledcubicle [dot] com
- www.lufa-lib.org
-*/
-
-/*
- Copyright 2014 Dean Camera (dean [at] fourwalledcubicle [dot] com)
-
- Permission to use, copy, modify, distribute, and sell this
- software and its documentation for any purpose is hereby granted
- without fee, provided that the above copyright notice appear in
- all copies and that both that the copyright notice and this
- permission notice and warranty disclaimer appear in supporting
- documentation, and that the name of the author not be used in
- advertising or publicity pertaining to distribution of the
- software without specific, written prior permission.
-
- The author disclaims all warranties with regard to this
- software, including all implied warranties of merchantability
- and fitness. In no event shall the author be liable for any
- special, indirect or consequential damages or any damages
- whatsoever resulting from loss of use, data or profits, whether
- in an action of contract, negligence or other tortious action,
- arising out of or in connection with the use or performance of
- this software.
-*/
-
-; Trampolines to actual API implementations if the target address is outside the
-; range of a rjmp instruction (can happen with large bootloader sections)
-.section .apitable_trampolines, "ax"
-.global BootloaderAPI_Trampolines
-BootloaderAPI_Trampolines:
-
- BootloaderAPI_ErasePage_Trampoline:
- jmp BootloaderAPI_ErasePage
- BootloaderAPI_WritePage_Trampoline:
- jmp BootloaderAPI_WritePage
- BootloaderAPI_FillWord_Trampoline:
- jmp BootloaderAPI_FillWord
- BootloaderAPI_ReadSignature_Trampoline:
- jmp BootloaderAPI_ReadSignature
- BootloaderAPI_ReadFuse_Trampoline:
- jmp BootloaderAPI_ReadFuse
- BootloaderAPI_ReadLock_Trampoline:
- jmp BootloaderAPI_ReadLock
- BootloaderAPI_WriteLock_Trampoline:
- jmp BootloaderAPI_WriteLock
- BootloaderAPI_UNUSED1:
- ret
- BootloaderAPI_UNUSED2:
- ret
- BootloaderAPI_UNUSED3:
- ret
- BootloaderAPI_UNUSED4:
- ret
- BootloaderAPI_UNUSED5:
- ret
-
-
-
-; API function jump table
-.section .apitable_jumptable, "ax"
-.global BootloaderAPI_JumpTable
-BootloaderAPI_JumpTable:
-
- rjmp BootloaderAPI_ErasePage_Trampoline
- rjmp BootloaderAPI_WritePage_Trampoline
- rjmp BootloaderAPI_FillWord_Trampoline
- rjmp BootloaderAPI_ReadSignature_Trampoline
- rjmp BootloaderAPI_ReadFuse_Trampoline
- rjmp BootloaderAPI_ReadLock_Trampoline
- rjmp BootloaderAPI_WriteLock_Trampoline
- rjmp BootloaderAPI_UNUSED1 ; UNUSED ENTRY 1
- rjmp BootloaderAPI_UNUSED2 ; UNUSED ENTRY 2
- rjmp BootloaderAPI_UNUSED3 ; UNUSED ENTRY 3
- rjmp BootloaderAPI_UNUSED4 ; UNUSED ENTRY 4
- rjmp BootloaderAPI_UNUSED5 ; UNUSED ENTRY 5
-
-
-
-; Bootloader table signatures and information
-.section .apitable_signatures, "ax"
-.global BootloaderAPI_Signatures
-BootloaderAPI_Signatures:
-
- .long BOOT_START_ADDR ; Start address of the bootloader
- .word 0xDF20 ; Signature for the Printer class bootloader
- .word 0xDCFB ; Signature for a LUFA class bootloader
+/* + LUFA Library + Copyright (C) Dean Camera, 2014. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2014 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaims all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +; Trampolines to actual API implementations if the target address is outside the +; range of a rjmp instruction (can happen with large bootloader sections) +.section .apitable_trampolines, "ax" +.global BootloaderAPI_Trampolines +BootloaderAPI_Trampolines: + + BootloaderAPI_ErasePage_Trampoline: + jmp BootloaderAPI_ErasePage + BootloaderAPI_WritePage_Trampoline: + jmp BootloaderAPI_WritePage + BootloaderAPI_FillWord_Trampoline: + jmp BootloaderAPI_FillWord + BootloaderAPI_ReadSignature_Trampoline: + jmp BootloaderAPI_ReadSignature + BootloaderAPI_ReadFuse_Trampoline: + jmp BootloaderAPI_ReadFuse + BootloaderAPI_ReadLock_Trampoline: + jmp BootloaderAPI_ReadLock + BootloaderAPI_WriteLock_Trampoline: + jmp BootloaderAPI_WriteLock + BootloaderAPI_UNUSED1: + ret + BootloaderAPI_UNUSED2: + ret + BootloaderAPI_UNUSED3: + ret + BootloaderAPI_UNUSED4: + ret + BootloaderAPI_UNUSED5: + ret + + + +; API function jump table +.section .apitable_jumptable, "ax" +.global BootloaderAPI_JumpTable +BootloaderAPI_JumpTable: + + rjmp BootloaderAPI_ErasePage_Trampoline + rjmp BootloaderAPI_WritePage_Trampoline + rjmp BootloaderAPI_FillWord_Trampoline + rjmp BootloaderAPI_ReadSignature_Trampoline + rjmp BootloaderAPI_ReadFuse_Trampoline + rjmp BootloaderAPI_ReadLock_Trampoline + rjmp BootloaderAPI_WriteLock_Trampoline + rjmp BootloaderAPI_UNUSED1 ; UNUSED ENTRY 1 + rjmp BootloaderAPI_UNUSED2 ; UNUSED ENTRY 2 + rjmp BootloaderAPI_UNUSED3 ; UNUSED ENTRY 3 + rjmp BootloaderAPI_UNUSED4 ; UNUSED ENTRY 4 + rjmp BootloaderAPI_UNUSED5 ; UNUSED ENTRY 5 + + + +; Bootloader table signatures and information +.section .apitable_signatures, "ax" +.global BootloaderAPI_Signatures +BootloaderAPI_Signatures: + + .long BOOT_START_ADDR ; Start address of the bootloader + .word 0xDF20 ; Signature for the Printer class bootloader + .word 0xDCFB ; Signature for a LUFA class bootloader diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/asf.xml b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/asf.xml index 86a56911ed..b5c0c6b3a5 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/asf.xml +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/asf.xml @@ -1,159 +1,159 @@ -<asf xmlversion="1.0">
- <project caption="Printer Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.128_4" force-caption="true" workspace-name="lufa_printer_128kb_4kb_">
- <require idref="lufa.bootloaders.printer"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb1287"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1F000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="Printer Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.64_4" force-caption="true" workspace-name="lufa_printer_64kb_4kb_">
- <require idref="lufa.bootloaders.printer"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="at90usb647"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0xF000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="Printer Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.32_4" force-caption="true" workspace-name="lufa_printer_32kb_4kb_">
- <require idref="lufa.bootloaders.printer"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega32u4"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x7000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="Printer Bootloader - 16KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.16_4" force-caption="true" workspace-name="lufa_printer_16kb_4kb_">
- <require idref="lufa.bootloaders.printer"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega16u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x3000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <project caption="Printer Bootloader - 8KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.8_4" force-caption="true" workspace-name="lufa_printer_8kb_4kb_">
- <require idref="lufa.bootloaders.printer"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8"/>
-
- <device-support value="atmega8u2"/>
- <config name="lufa.drivers.board.name" value="none"/>
-
- <config name="config.compiler.optimization.level" value="size"/>
-
- <build type="define" name="F_CPU" value="16000000UL"/>
- <build type="define" name="F_USB" value="16000000UL"/>
-
- <build type="define" name="BOOT_START_ADDR" value="0x1000"/>
- <build type="linker-config" subtype="flags" value="--section-start=.text=0x1000"/>
-
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FA0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FE0"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/>
- <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FF8"/>
- <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/>
- </project>
-
- <module type="application" id="lufa.bootloaders.printer" caption="Printer Bootloader">
- <info type="description" value="summary">
- Printer Class Bootloader, capable of reprogramming a device by "printing" new HEX files to the virtual Plain-Text printer it creates when plugged into a host.
- </info>
-
- <info type="gui-flag" value="move-to-root"/>
-
- <info type="keyword" value="Technology">
- <keyword value="Bootloaders"/>
- <keyword value="USB Device"/>
- </info>
-
- <device-support-alias value="lufa_avr8"/>
- <device-support-alias value="lufa_xmega"/>
- <device-support-alias value="lufa_uc3"/>
-
- <build type="include-path" value="."/>
- <build type="c-source" value="BootloaderPrinter.c"/>
- <build type="header-file" value="BootloaderPrinter.h"/>
- <build type="c-source" value="Descriptors.c"/>
- <build type="header-file" value="Descriptors.h"/>
- <build type="c-source" value="BootloaderAPI.c"/>
- <build type="header-file" value="BootloaderAPI.h"/>
- <build type="asm-source" value="BootloaderAPITable.S"/>
-
- <build type="module-config" subtype="path" value="Config"/>
- <build type="header-file" value="Config/LUFAConfig.h"/>
-
- <build type="distribute" subtype="user-file" value="doxyfile"/>
- <build type="distribute" subtype="user-file" value="BootloaderPrinter.txt"/>
-
- <require idref="lufa.common"/>
- <require idref="lufa.platform"/>
- <require idref="lufa.drivers.usb"/>
- <require idref="lufa.drivers.board"/>
- <require idref="lufa.drivers.board.leds"/>
- </module>
-</asf>
+<asf xmlversion="1.0"> + <project caption="Printer Bootloader - 128KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.128_4" force-caption="true" workspace-name="lufa_printer_128kb_4kb_"> + <require idref="lufa.bootloaders.printer"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb1287"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1F000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1F000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="Printer Bootloader - 64KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.64_4" force-caption="true" workspace-name="lufa_printer_64kb_4kb_"> + <require idref="lufa.bootloaders.printer"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="at90usb647"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0xF000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0xF000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0xFFA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0xFFE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0xFFF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="Printer Bootloader - 32KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.32_4" force-caption="true" workspace-name="lufa_printer_32kb_4kb_"> + <require idref="lufa.bootloaders.printer"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega32u4"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x7000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x7000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x7FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x7FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x7FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="Printer Bootloader - 16KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.16_4" force-caption="true" workspace-name="lufa_printer_16kb_4kb_"> + <require idref="lufa.bootloaders.printer"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega16u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x3000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x3000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x3FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x3FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x3FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <project caption="Printer Bootloader - 8KB FLASH / 4KB Boot - AVR8 Architecture" id="lufa.bootloaders.printer.avr8.8_4" force-caption="true" workspace-name="lufa_printer_8kb_4kb_"> + <require idref="lufa.bootloaders.printer"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8"/> + + <device-support value="atmega8u2"/> + <config name="lufa.drivers.board.name" value="none"/> + + <config name="config.compiler.optimization.level" value="size"/> + + <build type="define" name="F_CPU" value="16000000UL"/> + <build type="define" name="F_USB" value="16000000UL"/> + + <build type="define" name="BOOT_START_ADDR" value="0x1000"/> + <build type="linker-config" subtype="flags" value="--section-start=.text=0x1000"/> + + <build type="linker-config" subtype="flags" value="--section-start=.apitable_trampolines=0x1FA0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Trampolines"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_jumptable=0x1FE0"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_JumpTable"/> + <build type="linker-config" subtype="flags" value="--section-start=.apitable_signatures=0x1FF8"/> + <build type="linker-config" subtype="flags" value="--undefined=BootloaderAPI_Signatures"/> + </project> + + <module type="application" id="lufa.bootloaders.printer" caption="Printer Bootloader"> + <info type="description" value="summary"> + Printer Class Bootloader, capable of reprogramming a device by "printing" new HEX files to the virtual Plain-Text printer it creates when plugged into a host. + </info> + + <info type="gui-flag" value="move-to-root"/> + + <info type="keyword" value="Technology"> + <keyword value="Bootloaders"/> + <keyword value="USB Device"/> + </info> + + <device-support-alias value="lufa_avr8"/> + <device-support-alias value="lufa_xmega"/> + <device-support-alias value="lufa_uc3"/> + + <build type="include-path" value="."/> + <build type="c-source" value="BootloaderPrinter.c"/> + <build type="header-file" value="BootloaderPrinter.h"/> + <build type="c-source" value="Descriptors.c"/> + <build type="header-file" value="Descriptors.h"/> + <build type="c-source" value="BootloaderAPI.c"/> + <build type="header-file" value="BootloaderAPI.h"/> + <build type="asm-source" value="BootloaderAPITable.S"/> + + <build type="module-config" subtype="path" value="Config"/> + <build type="header-file" value="Config/LUFAConfig.h"/> + + <build type="distribute" subtype="user-file" value="doxyfile"/> + <build type="distribute" subtype="user-file" value="BootloaderPrinter.txt"/> + + <require idref="lufa.common"/> + <require idref="lufa.platform"/> + <require idref="lufa.drivers.usb"/> + <require idref="lufa.drivers.board"/> + <require idref="lufa.drivers.board.leds"/> + </module> +</asf> diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/makefile b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/makefile index 0716c3bbe8..0db035de3b 100644 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/makefile +++ b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/Printer/makefile @@ -1,55 +1,55 @@ -#
-# LUFA Library
-# Copyright (C) Dean Camera, 2014.
-#
-# dean [at] fourwalledcubicle [dot] com
-# www.lufa-lib.org
-#
-# --------------------------------------
-# LUFA Project Makefile.
-# --------------------------------------
-
-# Run "make help" for target help.
-
-MCU = at90usb1287
-ARCH = AVR8
-BOARD = USBKEY
-F_CPU = 8000000
-F_USB = $(F_CPU)
-OPTIMIZATION = s
-TARGET = BootloaderPrinter
-SRC = $(TARGET).c Descriptors.c BootloaderAPI.c BootloaderAPITable.S $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS)
-LUFA_PATH = ../../LUFA
-CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ -DBOOT_START_ADDR=$(BOOT_START_OFFSET)
-LD_FLAGS = -Wl,--section-start=.text=$(BOOT_START_OFFSET) $(BOOT_API_LD_FLAGS)
-
-# Flash size and bootloader section sizes of the target, in KB. These must
-# match the target's total FLASH size and the bootloader size set in the
-# device's fuses.
-FLASH_SIZE_KB = 128
-BOOT_SECTION_SIZE_KB = 8
-
-# Bootloader address calculation formulas
-# Do not modify these macros, but rather modify the dependent values above.
-CALC_ADDRESS_IN_HEX = $(shell printf "0x%X" $$(( $(1) )) )
-BOOT_START_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) - $(BOOT_SECTION_SIZE_KB)) * 1024 )
-BOOT_SEC_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) * 1024) - ($(strip $(1))) )
-
-# Bootloader linker section flags for relocating the API table sections to
-# known FLASH addresses - these should not normally be user-edited.
-BOOT_SECTION_LD_FLAG = -Wl,--section-start=$(strip $(1))=$(call BOOT_SEC_OFFSET, $(3)) -Wl,--undefined=$(strip $(2))
-BOOT_API_LD_FLAGS = $(call BOOT_SECTION_LD_FLAG, .apitable_trampolines, BootloaderAPI_Trampolines, 96)
-BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_jumptable, BootloaderAPI_JumpTable, 32)
-BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_signatures, BootloaderAPI_Signatures, 8)
-
-# Default target
-all:
-
-# Include LUFA build script makefiles
-include $(LUFA_PATH)/Build/lufa_core.mk
-include $(LUFA_PATH)/Build/lufa_sources.mk
-include $(LUFA_PATH)/Build/lufa_build.mk
-include $(LUFA_PATH)/Build/lufa_cppcheck.mk
-include $(LUFA_PATH)/Build/lufa_doxygen.mk
-include $(LUFA_PATH)/Build/lufa_avrdude.mk
-include $(LUFA_PATH)/Build/lufa_atprogram.mk
+# +# LUFA Library +# Copyright (C) Dean Camera, 2014. +# +# dean [at] fourwalledcubicle [dot] com +# www.lufa-lib.org +# +# -------------------------------------- +# LUFA Project Makefile. +# -------------------------------------- + +# Run "make help" for target help. + +MCU = at90usb1287 +ARCH = AVR8 +BOARD = USBKEY +F_CPU = 8000000 +F_USB = $(F_CPU) +OPTIMIZATION = s +TARGET = BootloaderPrinter +SRC = $(TARGET).c Descriptors.c BootloaderAPI.c BootloaderAPITable.S $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS) +LUFA_PATH = ../../LUFA +CC_FLAGS = -DUSE_LUFA_CONFIG_HEADER -IConfig/ -DBOOT_START_ADDR=$(BOOT_START_OFFSET) +LD_FLAGS = -Wl,--section-start=.text=$(BOOT_START_OFFSET) $(BOOT_API_LD_FLAGS) + +# Flash size and bootloader section sizes of the target, in KB. These must +# match the target's total FLASH size and the bootloader size set in the +# device's fuses. +FLASH_SIZE_KB = 128 +BOOT_SECTION_SIZE_KB = 8 + +# Bootloader address calculation formulas +# Do not modify these macros, but rather modify the dependent values above. +CALC_ADDRESS_IN_HEX = $(shell printf "0x%X" $$(( $(1) )) ) +BOOT_START_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) - $(BOOT_SECTION_SIZE_KB)) * 1024 ) +BOOT_SEC_OFFSET = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) * 1024) - ($(strip $(1))) ) + +# Bootloader linker section flags for relocating the API table sections to +# known FLASH addresses - these should not normally be user-edited. +BOOT_SECTION_LD_FLAG = -Wl,--section-start=$(strip $(1))=$(call BOOT_SEC_OFFSET, $(3)) -Wl,--undefined=$(strip $(2)) +BOOT_API_LD_FLAGS = $(call BOOT_SECTION_LD_FLAG, .apitable_trampolines, BootloaderAPI_Trampolines, 96) +BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_jumptable, BootloaderAPI_JumpTable, 32) +BOOT_API_LD_FLAGS += $(call BOOT_SECTION_LD_FLAG, .apitable_signatures, BootloaderAPI_Signatures, 8) + +# Default target +all: + +# Include LUFA build script makefiles +include $(LUFA_PATH)/Build/lufa_core.mk +include $(LUFA_PATH)/Build/lufa_sources.mk +include $(LUFA_PATH)/Build/lufa_build.mk +include $(LUFA_PATH)/Build/lufa_cppcheck.mk +include $(LUFA_PATH)/Build/lufa_doxygen.mk +include $(LUFA_PATH)/Build/lufa_avrdude.mk +include $(LUFA_PATH)/Build/lufa_atprogram.mk diff --git a/tmk_core/protocol/lufa/LUFA-git/LUFA/Build/HID_EEPROM_Loader/makefile b/tmk_core/protocol/lufa/LUFA-git/LUFA/Build/HID_EEPROM_Loader/makefile index 9fd188c936..e839ba6b1d 100644 --- a/tmk_core/protocol/lufa/LUFA-git/LUFA/Build/HID_EEPROM_Loader/makefile +++ b/tmk_core/protocol/lufa/LUFA-git/LUFA/Build/HID_EEPROM_Loader/makefile @@ -1,42 +1,42 @@ -#
-# LUFA Library
-# Copyright (C) Dean Camera, 2014.
-#
-# dean [at] fourwalledcubicle [dot] com
-# www.lufa-lib.org
-#
-# --------------------------------------
-# LUFA Project Makefile.
-# --------------------------------------
-
-# Run "make help" for target help.
-
-MCU = at90usb1287
-ARCH = AVR8
-F_CPU = 1000000
-F_USB = $(F_CPU)
-OPTIMIZATION = s
-TARGET = HID_EEPROM_Loader
-SRC = $(TARGET).c
-LUFA_PATH = ../../../LUFA
-CC_FLAGS =
-LD_FLAGS =
-OBJECT_FILES = InputEEData.o
-
-# Default target
-all:
-
-# Determine the AVR sub-architecture of the build main application object file
-FIND_AVR_SUBARCH = avr$(shell avr-objdump -f $(TARGET).o | grep architecture | cut -d':' -f3 | cut -d',' -f1)
-
-# Create a linkable object file with the input binary EEPROM data stored in the FLASH section
-InputEEData.o: InputEEData.bin $(TARGET).o $(MAKEFILE_LIST)
- @echo $(MSG_OBJCPY_CMD) Converting \"$<\" to a object file \"$@\"
- avr-objcopy -I binary -O elf32-avr -B $(call FIND_AVR_SUBARCH) --rename-section .data=.progmem.data,contents,alloc,readonly,data $< $@
-
-# Include LUFA build script makefiles
-include $(LUFA_PATH)/Build/lufa_core.mk
-include $(LUFA_PATH)/Build/lufa_build.mk
-include $(LUFA_PATH)/Build/lufa_cppcheck.mk
-include $(LUFA_PATH)/Build/lufa_doxygen.mk
-include $(LUFA_PATH)/Build/lufa_hid.mk
+# +# LUFA Library +# Copyright (C) Dean Camera, 2014. +# +# dean [at] fourwalledcubicle [dot] com +# www.lufa-lib.org +# +# -------------------------------------- +# LUFA Project Makefile. +# -------------------------------------- + +# Run "make help" for target help. + +MCU = at90usb1287 +ARCH = AVR8 +F_CPU = 1000000 +F_USB = $(F_CPU) +OPTIMIZATION = s +TARGET = HID_EEPROM_Loader +SRC = $(TARGET).c +LUFA_PATH = ../../../LUFA +CC_FLAGS = +LD_FLAGS = +OBJECT_FILES = InputEEData.o + +# Default target +all: + +# Determine the AVR sub-architecture of the build main application object file +FIND_AVR_SUBARCH = avr$(shell avr-objdump -f $(TARGET).o | grep architecture | cut -d':' -f3 | cut -d',' -f1) + +# Create a linkable object file with the input binary EEPROM data stored in the FLASH section +InputEEData.o: InputEEData.bin $(TARGET).o $(MAKEFILE_LIST) + @echo $(MSG_OBJCPY_CMD) Converting \"$<\" to a object file \"$@\" + avr-objcopy -I binary -O elf32-avr -B $(call FIND_AVR_SUBARCH) --rename-section .data=.progmem.data,contents,alloc,readonly,data $< $@ + +# Include LUFA build script makefiles +include $(LUFA_PATH)/Build/lufa_core.mk +include $(LUFA_PATH)/Build/lufa_build.mk +include $(LUFA_PATH)/Build/lufa_cppcheck.mk +include $(LUFA_PATH)/Build/lufa_doxygen.mk +include $(LUFA_PATH)/Build/lufa_hid.mk diff --git a/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/DeviceTemplate/asf.xml b/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/DeviceTemplate/asf.xml index fd65db283f..e952714e16 100644 --- a/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/DeviceTemplate/asf.xml +++ b/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/DeviceTemplate/asf.xml @@ -1,55 +1,55 @@ -<asf xmlversion="1.0">
- <project caption="USB Device Template" id="lufa.templates.device.project.avr8">
- <require idref="lufa.templates.device"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8_template"/>
-
- <device-support value="at90usb1287"/>
- <config name="lufa.drivers.board.name" value="usbkey"/>
-
- <build type="define" name="F_CPU" value="8000000UL"/>
- <build type="define" name="F_USB" value="8000000UL"/>
- </project>
-
- <project caption="USB Device Template" id="lufa.templates.device.project.xmega">
- <require idref="lufa.templates.device"/>
- <require idref="lufa.boards.dummy.xmega"/>
- <generator value="as5_8_template"/>
-
- <device-support value="atxmega256a3bu"/>
- <config name="lufa.drivers.board.name" value="a3bu_xplained"/>
-
- <build type="define" name="F_CPU" value="32000000UL"/>
- <build type="define" name="F_USB" value="48000000UL"/>
- </project>
-
- <module type="application" id="lufa.templates.device" caption="USB Device Template">
- <info type="description" value="summary">
- Template for a LUFA USB device mode application.
- </info>
-
- <info type="gui-flag" value="move-to-root"/>
-
- <info type="keyword" value="Technology">
- <keyword value="USB Device"/>
- <keyword value="Template Projects"/>
- </info>
-
- <device-support-alias value="lufa_avr8"/>
- <device-support-alias value="lufa_xmega"/>
- <device-support-alias value="lufa_uc3"/>
-
- <build type="c-source" value="DeviceApplication.c"/>
- <build type="c-source" value="Descriptors.c"/>
- <build type="header-file" value="DeviceApplication.h"/>
- <build type="header-file" value="Descriptors.h"/>
-
- <build type="module-config" subtype="path" value=".."/>
- <build type="header-file" value="../LUFAConfig.h"/>
-
- <require idref="lufa.common"/>
- <require idref="lufa.platform"/>
- <require idref="lufa.drivers.usb"/>
- <require idref="lufa.drivers.board"/>
- </module>
-</asf>
+<asf xmlversion="1.0"> + <project caption="USB Device Template" id="lufa.templates.device.project.avr8"> + <require idref="lufa.templates.device"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8_template"/> + + <device-support value="at90usb1287"/> + <config name="lufa.drivers.board.name" value="usbkey"/> + + <build type="define" name="F_CPU" value="8000000UL"/> + <build type="define" name="F_USB" value="8000000UL"/> + </project> + + <project caption="USB Device Template" id="lufa.templates.device.project.xmega"> + <require idref="lufa.templates.device"/> + <require idref="lufa.boards.dummy.xmega"/> + <generator value="as5_8_template"/> + + <device-support value="atxmega256a3bu"/> + <config name="lufa.drivers.board.name" value="a3bu_xplained"/> + + <build type="define" name="F_CPU" value="32000000UL"/> + <build type="define" name="F_USB" value="48000000UL"/> + </project> + + <module type="application" id="lufa.templates.device" caption="USB Device Template"> + <info type="description" value="summary"> + Template for a LUFA USB device mode application. + </info> + + <info type="gui-flag" value="move-to-root"/> + + <info type="keyword" value="Technology"> + <keyword value="USB Device"/> + <keyword value="Template Projects"/> + </info> + + <device-support-alias value="lufa_avr8"/> + <device-support-alias value="lufa_xmega"/> + <device-support-alias value="lufa_uc3"/> + + <build type="c-source" value="DeviceApplication.c"/> + <build type="c-source" value="Descriptors.c"/> + <build type="header-file" value="DeviceApplication.h"/> + <build type="header-file" value="Descriptors.h"/> + + <build type="module-config" subtype="path" value=".."/> + <build type="header-file" value="../LUFAConfig.h"/> + + <require idref="lufa.common"/> + <require idref="lufa.platform"/> + <require idref="lufa.drivers.usb"/> + <require idref="lufa.drivers.board"/> + </module> +</asf> diff --git a/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/HostTemplate/asf.xml b/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/HostTemplate/asf.xml index c1996ec711..c3860c056d 100644 --- a/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/HostTemplate/asf.xml +++ b/tmk_core/protocol/lufa/LUFA-git/LUFA/CodeTemplates/HostTemplate/asf.xml @@ -1,41 +1,41 @@ -<asf xmlversion="1.0">
- <project caption="USB Host Template" id="lufa.templates.host.project">
- <require idref="lufa.templates.host"/>
- <require idref="lufa.boards.dummy.avr8"/>
- <generator value="as5_8_template"/>
-
- <device-support value="at90usb1287"/>
- <config name="lufa.drivers.board.name" value="usbkey"/>
-
- <build type="define" name="F_CPU" value="8000000UL"/>
- <build type="define" name="F_USB" value="8000000UL"/>
- </project>
-
- <module type="application" id="lufa.templates.host" caption="USB Host Template">
- <info type="description" value="summary">
- Template for a LUFA USB host mode application.
- </info>
-
- <info type="gui-flag" value="move-to-root"/>
-
- <info type="keyword" value="Technology">
- <keyword value="USB Host"/>
- <keyword value="Template Projects"/>
- </info>
-
- <device-support-alias value="lufa_avr8"/>
- <device-support-alias value="lufa_xmega"/>
- <device-support-alias value="lufa_uc3"/>
-
- <build type="c-source" value="HostApplication.c"/>
- <build type="header-file" value="HostApplication.h"/>
-
- <build type="module-config" subtype="path" value=".."/>
- <build type="header-file" value="../LUFAConfig.h"/>
-
- <require idref="lufa.common"/>
- <require idref="lufa.platform"/>
- <require idref="lufa.drivers.usb"/>
- <require idref="lufa.drivers.board"/>
- </module>
-</asf>
+<asf xmlversion="1.0"> + <project caption="USB Host Template" id="lufa.templates.host.project"> + <require idref="lufa.templates.host"/> + <require idref="lufa.boards.dummy.avr8"/> + <generator value="as5_8_template"/> + + <device-support value="at90usb1287"/> + <config name="lufa.drivers.board.name" value="usbkey"/> + + <build type="define" name="F_CPU" value="8000000UL"/> + <build type="define" name="F_USB" value="8000000UL"/> + </project> + + <module type="application" id="lufa.templates.host" caption="USB Host Template"> + <info type="description" value="summary"> + Template for a LUFA USB host mode application. + </info> + + <info type="gui-flag" value="move-to-root"/> + + <info type="keyword" value="Technology"> + <keyword value="USB Host"/> + <keyword value="Template Projects"/> + </info> + + <device-support-alias value="lufa_avr8"/> + <device-support-alias value="lufa_xmega"/> + <device-support-alias value="lufa_uc3"/> + + <build type="c-source" value="HostApplication.c"/> + <build type="header-file" value="HostApplication.h"/> + + <build type="module-config" subtype="path" value=".."/> + <build type="header-file" value="../LUFAConfig.h"/> + + <require idref="lufa.common"/> + <require idref="lufa.platform"/> + <require idref="lufa.drivers.usb"/> + <require idref="lufa.drivers.board"/> + </module> +</asf> diff --git a/tmk_core/protocol/lufa/LUFA-git/LUFA/DoxygenPages/BuildSystem.txt b/tmk_core/protocol/lufa/LUFA-git/LUFA/DoxygenPages/BuildSystem.txt index 7ddfa1be3f..0ae1dd678f 100644 --- a/tmk_core/protocol/lufa/LUFA-git/LUFA/DoxygenPages/BuildSystem.txt +++ b/tmk_core/protocol/lufa/LUFA-git/LUFA/DoxygenPages/BuildSystem.txt @@ -1,975 +1,975 @@ -/** \file
- *
- * This file contains special DoxyGen information for the generation of the main page and other special
- * documentation pages. It is not a project source file.
- */
-
-/** \page Page_BuildSystem The LUFA Build System
- *
- * \section Sec_BuildSystem_Overview Overview of the LUFA Build System
- * The LUFA build system is an attempt at making a set of re-usable, modular build make files which
- * can be referenced in a LUFA powered project, to minimize the amount of code required in an
- * application makefile. The system is written in GNU Make, and each module is independent of
- * one-another.
- *
- * For details on the prerequisites needed for Linux and Windows machines to be able to use the LUFA
- * build system, see \ref Sec_CompilingApps_Prerequisites.
- *
- * To use a LUFA build system module, simply add an include to your project makefile. All user projects
- * should at a minimum include \ref Page_BuildModule_CORE for base functionality:
- * \code
- * include $(LUFA_PATH)/Build/lufa_core.mk
- * \endcode
- *
- * Once included in your project makefile, the associated build module targets will be added to your
- * project's build makefile targets automatically. To call a build target, run <tt>make {TARGET_NAME}</tt>
- * from the command line, substituting in the appropriate target name.
- *
- * \see \ref Sec_ConfiguringApps_AppMakefileParams for a copy of the sample LUFA project makefile.
- *
- * Each build module may have one or more mandatory parameters (GNU Make variables) which <i>must</i>
- * be supplied in the project makefile for the module to work, and one or more optional parameters which
- * may be defined and which will assume a sensible default if not.
- *
- * \section SSec_BuildSystem_Modules Available Modules
- *
- * The following modules are included in this LUFA release:
- *
- * \li \subpage Page_BuildModule_ATPROGRAM - Device Programming
- * \li \subpage Page_BuildModule_AVRDUDE - Device Programming
- * \li \subpage Page_BuildModule_BUILD - Compiling/Assembling/Linking
- * \li \subpage Page_BuildModule_CORE - Core Build System Functions
- * \li \subpage Page_BuildModule_CPPCHECK - Static Code Analysis
- * \li \subpage Page_BuildModule_DFU - Device Programming
- * \li \subpage Page_BuildModule_DOXYGEN - Automated Source Code Documentation
- * \li \subpage Page_BuildModule_HID - Device Programming
- * \li \subpage Page_BuildModule_SOURCES - LUFA Module Source Code Variables
- *
- * If you have problems building using the LUFA build system, see \subpage Page_BuildTroubleshooting for resolution steps.
- */
-
- /** \page Page_BuildModule_BUILD The BUILD build module
- *
- * The BUILD LUFA build system module, providing targets for the compilation,
- * assembling and linking of an application from source code into binary files
- * suitable for programming into a target device, using the GCC compiler.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_build.mk
- * \endcode
- *
- * \section SSec_BuildModule_BUILD_Requirements Requirements
- * This module requires the the architecture appropriate binaries of the GCC compiler are available in your
- * system's <b>PATH</b> variable. The GCC compiler and associated toolchain is distributed in Atmel AVR Studio
- * 5.x and Atmel Studio 6.x installation directories, as well as in many third party distribution packages.
- *
- * \section SSec_BuildModule_BUILD_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>size</tt></td>
- * <td>Display size of the compiled application FLASH and SRAM segments.</td>
- * </tr>
- * <tr>
- * <td><tt>symbol-sizes</tt></td>
- * <td>Display a size-sorted list of symbols from the compiled application, in decimal bytes.</td>
- * </tr>
- * <tr>
- * <td><tt>lib</tt></td>
- * <td>Build and archive all source files into a library A binary file.</td>
- * </tr>
- * <tr>
- * <td><tt>all</tt></td>
- * <td>Build and link the application into ELF debug and HEX binary files.</td>
- * </tr>
- * <tr>
- * <td><tt>elf</tt></td>
- * <td>Build and link the application into an ELF debug file.</td>
- * </tr>
- * <tr>
- * <td><tt>bin</tt></td>
- * <td>Build and link the application and produce a BIN binary file.</td>
- * </tr>
- * <tr>
- * <td><tt>hex</tt></td>
- * <td>Build and link the application and produce HEX and EEP binary files.</td>
- * </tr>
- * <tr>
- * <td><tt>lss</tt></td>
- * <td>Build and link the application and produce a LSS source code/assembly code mixed listing file.</td>
- * </tr>
- * <tr>
- * <td><tt>clean</tt></td>
- * <td>Remove all intermediary files and binary output files.</td>
- * </tr>
- * <tr>
- * <td><tt>mostlyclean</tt></td>
- * <td>Remove all intermediary files but preserve any binary output files.</td>
- * </tr>
- * <tr>
- * <td><tt><i><filename></i>.s</tt></td>
- * <td>Create an assembly listing of a given input C/C++ source file.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_BUILD_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>TARGET</tt></td>
- * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>ARCH</tt></td>
- * <td>Architecture of the target processor (see \ref Page_DeviceSupport).</td>
- * </tr>
- * <tr>
- * <td><tt>MCU</tt></td>
- * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>SRC</tt></td>
- * <td>List of relative or absolute paths to the application C (.c), C++ (.cpp) and Assembly (.S) source files.</td>
- * </tr>
- * <tr>
- * <td><tt>F_USB</tt></td>
- * <td>Speed in Hz of the input clock frequency to the target's USB controller.</td>
- * </tr>
- * <tr>
- * <td><tt>LUFA_PATH</tt></td>
- * <td>Path to the LUFA library core, either relative or absolute (e.g. <tt>../LUFA-000000/LUFA/</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_BUILD_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><tt>BOARD</tt></td>
- * <td>LUFA board hardware drivers to use (see \ref Page_DeviceSupport).</td>
- * </tr>
- * <tr>
- * <td><tt>OPTIMIZATION</tt></td>
- * <td>Optimization level to use when compiling source files (see GCC manual).</td>
- * </tr>
- * <tr>
- * <td><tt>C_STANDARD</tt></td>
- * <td>Version of the C standard to apply when compiling C++ source files (see GCC manual).</td>
- * </tr>
- * <tr>
- * <td><tt>CPP_STANDARD</tt></td>
- * <td>Version of the C++ standard to apply when compiling C++ source files (see GCC manual).</td>
- * </tr>
- * <tr>
- * <td><tt>DEBUG_FORMAT</tt></td>
- * <td>Format of the debug information to embed in the generated object files (see GCC manual).</td>
- * </tr>
- * <tr>
- * <td><tt>DEBUG_LEVEL</tt></td>
- * <td>Level of the debugging information to embed in the generated object files (see GCC manual).</td>
- * </tr>
- * <tr>
- * <td><tt>F_CPU</tt></td>
- * <td>Speed of the processor CPU clock, in Hz.</td>
- * </tr>
- * <tr>
- * <td><tt>C_FLAGS</tt></td>
- * <td>Flags to pass to the C compiler only, after the automatically generated flags.</td>
- * </tr>
- * <tr>
- * <td><tt>CPP_FLAGS</tt></td>
- * <td>Flags to pass to the C++ compiler only, after the automatically generated flags.</td>
- * </tr>
- * <tr>
- * <td><tt>ASM_FLAGS</tt></td>
- * <td>Flags to pass to the assembler only, after the automatically generated flags.</td>
- * </tr>
- * <tr>
- * <td><tt>CC_FLAGS</tt></td>
- * <td>Common flags to pass to the C/C++ compiler and assembler, after the automatically generated flags.</td>
- * </tr>
- * <tr>
- * <td><tt>COMPILER_PATH</tt></td>
- * <td>Directory where the C/C++ toolchain is located, if not available in the system <tt>PATH</tt>.</td>
- * </tr>
- * <tr>
- * <td><tt>LD_FLAGS</tt></td>
- * <td>Flags to pass to the linker, after the automatically generated flags.</td>
- * </tr>
- * <tr>
- * <td><tt>LINKER_RELAXATIONS</tt></td>
- * <td>Enables or disables linker relaxations when linking the application binary. This can reduce the total size
- * of the application by replacing full \c CALL instructions with smaller \c RCALL instructions where possible.
- * \note On some unpatched versions of binutils, this can cause link failures in some circumstances. If you
- * receive a link error <tt>relocation truncated to fit: R_AVR_13_PCREL</tt>, disable this setting.</td>
- * </tr>
- * <tr>
- * <td><tt>OBJDIR</tt></td>
- * <td>Directory to place the generated object and dependency files. If set to "." the same folder as the source file will be used.
- * \note When this option is enabled, all source filenames <b>must</b> be unique.</td>
- * </tr>
- * <tr>
- * <td><tt>OBJECT_FILES</tt></td>
- * <td>List of additional object files that should be linked into the resulting binary.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_BUILD_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_BUILD_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
-/** \page Page_BuildModule_CORE The CORE build module
- *
- * The core LUFA build system module, providing common build system help and information targets.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_core.mk
- * \endcode
- *
- * \section SSec_BuildModule_CORE_Requirements Requirements
- * This module has no requirements outside a standard *nix shell like environment; the <tt>sh</tt>
- * shell, GNU <tt>make</tt> and *nix CoreUtils (<tt>echo</tt>, <tt>printf</tt>, etc.).
- *
- * \section SSec_BuildModule_CORE_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>help</tt></td>
- * <td>Display build system help and configuration information.</td>
- * </tr>
- * <tr>
- * <td><tt>list_targets</tt></td>
- * <td>List all available build targets from the build system.</td>
- * </tr>
- * <tr>
- * <td><tt>list_modules</tt></td>
- * <td>List all available build modules from the build system.</td>
- * </tr>
- * <tr>
- * <td><tt>list_mandatory</tt></td>
- * <td>List all mandatory parameters required by the included modules.</td>
- * </tr>
- * <tr>
- * <td><tt>list_optional</tt></td>
- * <td>List all optional parameters required by the included modules.</td>
- * </tr>
- * <tr>
- * <td><tt>list_provided</tt></td>
- * <td>List all variables provided by the included modules.</td>
- * </tr>
- * <tr>
- * <td><tt>list_macros</tt></td>
- * <td>List all macros provided by the included modules.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CORE_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CORE_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CORE_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CORE_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
-/** \page Page_BuildModule_ATPROGRAM The ATPROGRAM build module
- *
- * The ATPROGRAM programming utility LUFA build system module, providing targets to reprogram an
- * Atmel processor FLASH and EEPROM memories with a project's compiled binary output files.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_atprogram.mk
- * \endcode
- *
- * \section SSec_BuildModule_ATPROGRAM_Requirements Requirements
- * This module requires the <tt>atprogram.exe</tt> utility to be available in your system's <b>PATH</b>
- * variable. The <tt>atprogram.exe</tt> utility is distributed in Atmel AVR Studio 5.x and Atmel Studio 6.x
- * inside the application install folder's "\atbackend" subdirectory.
- *
- * \section SSec_BuildModule_ATPROGRAM_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>atprogram</tt></td>
- * <td>Program the device FLASH memory with the application's executable data.</td>
- * </tr>
- * <tr>
- * <td><tt>atprogram-ee</tt></td>
- * <td>Program the device EEPROM memory with the application's EEPROM data.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_ATPROGRAM_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>MCU</tt></td>
- * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>TARGET</tt></td>
- * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_ATPROGRAM_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><tt>ATPROGRAM_PROGRAMMER</tt></td>
- * <td>Name of the Atmel programmer or debugger tool to communicate with (e.g. <tt>jtagice3</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>ATPROGRAM_INTERFACE</tt></td>
- * <td>Name of the programming interface to use when programming the target (e.g. <tt>spi</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>ATPROGRAM_PORT</tt></td>
- * <td>Name of the communication port to use when when programming with a serially connected tool (e.g. <tt>COM2</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_ATPROGRAM_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_ATPROGRAM_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
-/** \page Page_BuildModule_AVRDUDE The AVRDUDE build module
- *
- * The AVRDUDE programming utility LUFA build system module, providing targets to reprogram an
- * Atmel processor FLASH and EEPROM memories with a project's compiled binary output files.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_avrdude.mk
- * \endcode
- *
- * \section SSec_BuildModule_AVRDUDE_Requirements Requirements
- * This module requires the <tt>avrdude</tt> utility to be available in your system's <b>PATH</b>
- * variable. The <tt>avrdude</tt> utility is distributed in the old WinAVR project releases for
- * Windows (<a>http://winavr.sourceforge.net</a>) or can be installed on *nix systems via the project's
- * source code (<a>https://savannah.nongnu.org/projects/avrdude</a>) or through the package manager.
- *
- * \section SSec_BuildModule_AVRDUDE_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>avrdude</tt></td>
- * <td>Program the device FLASH memory with the application's executable data.</td>
- * </tr>
- * <tr>
- * <td><tt>avrdude-ee</tt></td>
- * <td>Program the device EEPROM memory with the application's EEPROM data.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_AVRDUDE_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>MCU</tt></td>
- * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>TARGET</tt></td>
- * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_AVRDUDE_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><tt>AVRDUDE_PROGRAMMER</tt></td>
- * <td>Name of the programmer or debugger tool to communicate with (e.g. <tt>jtagicemkii</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>AVRDUDE_PORT</tt></td>
- * <td>Name of the communication port to use when when programming with the connected tool (e.g. <tt>COM2</tt>, <tt>/dev/ttyUSB0</tt> or <tt>usb</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>AVRDUDE_FLAGS</tt></td>
- * <td>Additional flags to pass to avrdude when programming, applied after the automatically generated flags.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_AVRDUDE_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_AVRDUDE_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
- /** \page Page_BuildModule_CPPCHECK The CPPCHECK build module
- *
- * The CPPCHECK programming utility LUFA build system module, providing targets to statically
- * analyze C and C++ source code for errors and performance/style issues.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_cppcheck.mk
- * \endcode
- *
- * \section SSec_BuildModule_CPPCHECK_Requirements Requirements
- * This module requires the <tt>cppcheck</tt> utility to be available in your system's <b>PATH</b>
- * variable. The <tt>cppcheck</tt> utility is distributed through the project's home page
- * (<a>http://cppcheck.sourceforge.net</a>) for Windows, and can be installed on *nix systems via
- * the project's source code or through the package manager.
- *
- * \section SSec_BuildModule_CPPCHECK_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>cppcheck</tt></td>
- * <td>Statically analyze the project source code for issues.</td>
- * </tr>
- * <tr>
- * <td><tt>cppcheck-config</tt></td>
- * <td>Check the <tt>cppcheck</tt> configuration - scan source code and warn about missing header files and other issues.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CPPCHECK_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>SRC</tt></td>
- * <td>List of source files to statically analyze.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CPPCHECK_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><tt>CPPCHECK_INCLUDES</tt></td>
- * <td>Path of extra directories to check when attemting to resolve C/C++ header file includes.</td>
- * </tr>
- * <tr>
- * <td><tt>CPPCHECK_EXCLUDES</tt></td>
- * <td>Paths or path fragments to exclude when analyzing.</td>
- * </tr>
- * <tr>
- * <td><tt>CPPCHECK_MSG_TEMPLATE</tt></td>
- * <td>Output message template to use when printing errors, warnings and information (see <tt>cppcheck</tt> documentation).</td>
- * </tr>
- * <tr>
- * <td><tt>CPPCHECK_ENABLE</tt></td>
- * <td>Analysis rule categories to enable (see <tt>cppcheck</tt> documentation).</td>
- * </tr>
- * <tr>
- * <td><tt>CPPCHECK_SUPPRESS</tt></td>
- * <td>Specific analysis rules to suppress (see <tt>cppcheck</tt> documentation).</td>
- * </tr>
- * <tr>
- * <td><tt>CPPCHECK_FAIL_ON_WARNING</tt></td>
- * <td>Set to <b>Y</b> to fail the analysis job with an error exit code if warnings are found, <b>N</b> to continue without failing.</td>
- * </tr>
- * <tr>
- * <td><tt>CPPCHECK_QUIET</tt></td>
- * <td>Set to <b>Y</b> to suppress all output except warnings and errors, <b>N</b> to show verbose output information.</td>
- * </tr>
- * <tr>
- * <td><tt>CPPCHECK_FLAGS</tt></td>
- * <td>Extra flags to pass to <tt>cppcheck</tt>, after the automatically generated flags.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CPPCHECK_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_CPPCHECK_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
- /** \page Page_BuildModule_DFU The DFU build module
- *
- * The DFU programming utility LUFA build system module, providing targets to reprogram an
- * Atmel processor FLASH and EEPROM memories with a project's compiled binary output files.
- * This module requires a DFU class bootloader to be running in the target, compatible with
- * the DFU bootloader protocol as published by Atmel.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_dfu.mk
- * \endcode
- *
- * \section SSec_BuildModule_DFU_Requirements Requirements
- * This module requires either the <tt>batchisp</tt> utility from Atmel's FLIP utility, or the open
- * source <tt>dfu-programmer</tt> utility (<a>http://dfu-programmer.sourceforge.net/</a>) to be
- * available in your system's <b>PATH</b> variable. On *nix systems the <tt>dfu-programmer</tt> utility
- * can be installed via the project's source code or through the package manager.
- *
- * \section SSec_BuildModule_DFU_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>dfu</tt></td>
- * <td>Program the device FLASH memory with the application's executable data using <tt>dfu-programmer</tt>.</td>
- * </tr>
- * <tr>
- * <td><tt>dfu-ee</tt></td>
- * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>dfu-programmer</tt>.</td>
- * </tr>
- * <tr>
- * <td><tt>flip</tt></td>
- * <td>Program the device FLASH memory with the application's executable data using <tt>batchisp</tt>.</td>
- * </tr>
- * <tr>
- * <td><tt>flip-ee</tt></td>
- * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>batchisp</tt>.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DFU_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>MCU</tt></td>
- * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>TARGET</tt></td>
- * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DFU_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DFU_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DFU_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
- /** \page Page_BuildModule_DOXYGEN The DOXYGEN build module
- *
- * The DOXYGEN code documentation utility LUFA build system module, providing targets to generate
- * project HTML and other format documentation from a set of source files that include special
- * Doxygen comments.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_doxygen.mk
- * \endcode
- *
- * \section SSec_BuildModule_DOXYGEN_Requirements Requirements
- * This module requires the <tt>doxygen</tt> utility from the Doxygen website
- * (<a>http://www.doxygen.org/</a>) to be available in your system's <b>PATH</b> variable. On *nix
- * systems the <tt>doxygen</tt> utility can be installed via the project's source code or through
- * the package manager.
- *
- * \section SSec_BuildModule_DOXYGEN_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>doxygen</tt></td>
- * <td>Generate project documentation.</td>
- * </tr>
- * <tr>
- * <td><tt>doxygen_create</tt></td>
- * <td>Create a new Doxygen configuration file using the latest template.</td>
- * </tr>
- * <tr>
- * <td><tt>doxygen_upgrade</tt></td>
- * <td>Upgrade an existing Doxygen configuration file to the latest template</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DOXYGEN_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>LUFA_PATH</tt></td>
- * <td>Path to the LUFA library core, either relative or absolute (e.g. <tt>../LUFA-000000/LUFA/</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DOXYGEN_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><tt>DOXYGEN_CONF</tt></td>
- * <td>Name and path of the base Doxygen configuration file for the project.</td>
- * </tr>
- * <tr>
- * <td><tt>DOXYGEN_FAIL_ON_WARNING</tt></td>
- * <td>Set to <b>Y</b> to fail the generation with an error exit code if warnings are found other than unsupported configuration parameters, <b>N</b> to continue without failing.</td>
- * </tr>
- * <tr>
- * <td><tt>DOXYGEN_OVERRIDE_PARAMS</tt></td>
- * <td>Extra Doxygen configuration parameters to apply, overriding the corresponding config entry in the project's configuration file (e.g. <tt>QUIET=YES</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DOXYGEN_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_DOXYGEN_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
- /** \page Page_BuildModule_HID The HID build module
- *
- * The HID programming utility LUFA build system module, providing targets to reprogram an
- * Atmel processor's FLASH memory with a project's compiled binary output file. This module
- * requires a HID class bootloader to be running in the target, using a protocol compatible
- * with the PJRC "HalfKay" protocol (<a>http://www.pjrc.com/teensy/halfkay_protocol.html</a>).
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_hid.mk
- * \endcode
- *
- * \section SSec_BuildModule_HID_Requirements Requirements
- * This module requires either the <tt>hid_bootloader_cli</tt> utility from the included LUFA HID
- * class bootloader API subdirectory, or the <tt>teensy_loader_cli</tt> utility from PJRC
- * (<a>http://www.pjrc.com/teensy/loader_cli.html</a>) to be available in your system's <b>PATH</b>
- * variable.
- *
- * \section SSec_BuildModule_HID_Targets Targets
- *
- * <table>
- * <tr>
- * <td><tt>hid</tt></td>
- * <td>Program the device FLASH memory with the application's executable data using <tt>hid_bootloader_cli</tt>.</td>
- * </tr>
- * <tr>
- * <td><tt>hid-ee</tt></td>
- * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>hid_bootloader_cli</tt> and
- * a temporary AVR application programmed into the target's FLASH.
- * \note This will erase the currently loaded application in the target.</td>
- * </tr>
- * <tr>
- * <td><tt>teensy</tt></td>
- * <td>Program the device FLASH memory with the application's executable data using <tt>teensy_loader_cli</tt>.</td>
- * </tr>
- * <tr>
- * <td><tt>teensy-ee</tt></td>
- * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>teensy_loader_cli</tt> and
- * a temporary AVR application programmed into the target's FLASH.
- * \note This will erase the currently loaded application in the target.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_HID_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>MCU</tt></td>
- * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>TARGET</tt></td>
- * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_HID_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_HID_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_HID_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
- /** \page Page_BuildModule_SOURCES The SOURCES build module
- *
- * The SOURCES LUFA build system module, providing variables listing the various LUFA source files
- * required to be build by a project for a given LUFA module. This module gives a way to reference
- * LUFA source files symbolically, so that changes to the library structure do not break the library
- * makefile.
- *
- * To use this module in your application makefile, add the following code:
- * \code
- * include $(LUFA_PATH)/Build/lufa_sources.mk
- * \endcode
- *
- * \section SSec_BuildModule_SOURCES_Requirements Requirements
- * None.
- *
- * \section SSec_BuildModule_SOURCES_Targets Targets
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_SOURCES_MandatoryParams Mandatory Parameters
- *
- * <table>
- * <tr>
- * <td><tt>LUFA_PATH</tt></td>
- * <td>Path to the LUFA library core, either relative or absolute (e.g. <tt>../LUFA-000000/LUFA/</tt>).</td>
- * </tr>
- * <tr>
- * <td><tt>ARCH</tt></td>
- * <td>Architecture of the target processor (see \ref Page_DeviceSupport).</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_SOURCES_OptionalParams Optional Parameters
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_SOURCES_ProvidedVariables Module Provided Variables
- *
- * <table>
- * <tr>
- * <td><tt>LUFA_SRC_USB</tt></td>
- * <td>List of LUFA USB driver source files.</td>
- * </tr>
- * <tr>
- * <td><tt>LUFA_SRC_USBCLASS</tt></td>
- * <td>List of LUFA USB Class driver source files.</td>
- * </tr>
- * <tr>
- * <td><tt>LUFA_SRC_TEMPERATURE</tt></td>
- * <td>List of LUFA temperature sensor driver source files.</td>
- * </tr>
- * <tr>
- * <td><tt>LUFA_SRC_SERIAL</tt></td>
- * <td>List of LUFA Serial U(S)ART driver source files.</td>
- * </tr>
- * <tr>
- * <td><tt>LUFA_SRC_TWI</tt></td>
- * <td>List of LUFA TWI driver source files.</td>
- * </tr>
- * <tr>
- * <td><tt>LUFA_SRC_PLATFORM</tt></td>
- * <td>List of LUFA architecture specific platform management source files.</td>
- * </tr>
- * </table>
- *
- * \section SSec_BuildModule_SOURCES_ProvidedMacros Module Provided Macros
- *
- * <table>
- * <tr>
- * <td><i>None</i></td>
- * </tr>
- * </table>
- */
-
-/** \page Page_BuildTroubleshooting Troubleshooting Information
- *
- * LUFA uses a lot of advanced features of the AVR-GCC compiler, linker, and surrounding binaries. This can sometimes lead to problems compiling applications if one of these
- * features is buggy in the version of the tools used in a build environment. Missing utilities and incorrectly set makefile configuration options can also result in different
- * errors being produced when compilation or other operations are attempted. The table below lists a set of commonly encountered errors and their resolutions.
- *
- * <table>
- * <tr>
- * <th>Problem</th>
- * <th>Resolution</th>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>relocation truncated to fit: R_AVR_13_PCREL against symbol <i>{X}</i></tt></b>" shown when compiling.</td>
- * <td>Try compiling with the setting <tt>LINKER_RELAXATIONS=N</tt> in your LUFA Build System 2.0 makefile, or remove the line <tt>-Wl,--relax</tt>
- * from other makefiles. Alternatively, make sure you have the latest version of the Atmel Toolchain installed for your system.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>error: ld terminated with signal 11 [Segmentation fault]</tt></b>" shown when compiling.</td>
- * <td>Try compiling with the setting <tt>DEBUG_LEVEL=2</tt> in your LUFA Build System 2.0 makefile, or make sure you are using <tt>binutils</tt> version 2.22 or later.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>EMERGENCY ABORT: INFINITE RECURSION DETECTED</tt></b>" shown when compiling.</td>
- * <td>Make sure you are using an up to date version of GNU Make when compiling. This error is a safety system added to the mid-level makefiles, to prevent an issue with
- * GNU make or other variants of Make causing an infinitely recursive build.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Unsupported architecture "<i>{X}</i>"</tt></b>" shown when compiling.</td>
- * <td>Ensure your makefile's <tt>ARCH</tt> setting is set to one of the architecture names (case-sensitive) supported by the version of LUFA you are compiling against.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Makefile <i>{X}</i> value not set</tt></b>" shown when compiling.</td>
- * <td>The specified Makefile value was not configured in your project's makefile or on the command line, and the nominated setting is required by one or more LUFA
- * build system modules. Define the value in your project makefile and try again.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Makefile <i>{X}</i> option cannot be blank</tt></b>" shown when compiling.</td>
- * <td>The specified Makefile value was configured in your project's makefile or on the command line, but was set to an empty value. For the nominated configuration
- * option, an empty value is not allowed. Define the nominated setting to a correct non-blank value and try again.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Makefile <i>{X}</i> option must be Y or N</tt></b>" shown when compiling.</td>
- * <td>The specified Makefile value was configured in your project's makefile or on the command line, but was set to a value other than a Y (for "Yes") or "N" (for "No").
- * This configuration option is required to be one of the aforementioned boolean values, and other values are invalid. Set this option to either Y or N and try again.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Unknown input source file formats: <i>{X}</i></tt></b>" shown when compiling.</td>
- * <td>The nominated source files, specified in your project's makefile in the <tt>SRC</tt> configuration option, has an extension that the LUFA build system does not
- * recognise. The file extensions are case sensitive, and must be one of the supported formats (<tt>*.c</tt>, <tt>*.cpp</tt> or <tt>*.S</tt>).</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Cannot build with OBJDIR parameter set - one or more object file name is not unique</tt></b>" shown when compiling.</td>
- * <td>When a project is built with a non-empty <tt>OBJDIR</tt> object directory name set, all input source files must have unique names, excluding extension and path.
- * This means that input files that are named identically and differ only by their path or extension are invalid when this mode is used.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Source file does not exist: <i>{X}</i></tt></b>" shown when compiling.</td>
- * <td>The nominated input source file, specified in the user project's <tt>SRC</tt> parameter, could not be found. Ensure the source file exists and the absolute or
- * relative path given in the user project makefile is correct and try again.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>Doxygen configuration file <i>{X}</i> does not exist</tt></b>" shown when upgrading a Doxygen configuration file.</td>
- * <td>The nominated Doxygen configuration file, specified in the user project's <tt>DOXYGEN_CONF</tt> parameter, could not be found. Ensure the configuration file exists
- * and the absolute or relative path given in the user project makefile is correct and try again, or run the appropriate makefile target to generate a new configuration
- * file.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>avr-gcc: error: unrecognized option '<i>{X}</i>'</tt></b>" shown when compiling.</td>
- * <td>An unrecognised option was supplied to the compiler, usually in the <tt>C_FLAGS</tt>, <tt>CPP_FLAGS</tt>, <tt>ASM_FLAGS</tt> or <tt>CC_FLAGS</tt> configuration
- * options. The nominated compiler switch may be invalid, or unsupported by the version of AVR-GCC on the host system. Remove the unrecognised flag if invalid, or
- * upgrade to the latest AVR-GCC. If the option is a valid linker option, use the prefix "-Wl," to ensure it is passed to the linker correctly.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>makefile:{X}: {Y}.mk: No such file or directory</tt></b>" shown when make is invoked.</td>
- * <td>The path to the nominated makefile module was incorrect. This usually indicates that the makefile <tt>LUFA_PATH</tt> option is not set to a valid relative or
- * absolute path to the LUFA library core.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>fatal error: LUFAConfig.h: No such file or directory</tt></b>" shown when compiling.</td>
- * <td>The <tt>USE_LUFA_CONFIG_HEADER</tt> compile time option was set in the user project makefile, but the user supplied <tt>LUFAConfig.h</tt> header could not be
- * found. Ensure that the directory that contains this configuration file is correctly passed to the compiler via the -I switch in the makefile <tt>CC_FLAGS</tt>
- * parameter.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>ld.exe: section .apitable_trampolines loaded at <i>{X}</i> overlaps section .text</tt></b>" shown when compiling a bootloader.</td>
- * <td>The bootloader is compiling too large for the given <tt>FLASH_SIZE_KB</tt> and <tt>BOOT_SECTION_SIZE_KB</tt> parameters set in the bootloader makefile. This
- * usually indicates that these values are incorrect for the specified device the bootloader is targeting. If these values are correct, a newer version of the
- * compiler may need to be used to ensure that the bootloader is built within the section size constraints of the target device.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>unknown MCU '<i>{X}</i>' specified</tt></b>" shown when compiling.</td>
- * <td>The specified microcontroller device model name set in the user application's makefile as the <tt>MCU</tt> parameter is incorrect, or unsupported by the
- * version of the compiler being used. Make sure the model name is correct, or upgrade to the latest Atmel Toolchain to obtain newer device support.</td>
- * </tr>
- * <tr>
- * <td>Error "<b><tt>undefined reference to `<i>{X}</i>'</tt></b>" shown when compiling.</td>
- * <td>This is usually caused by a missing source file in the user application's <tt>SRC</tt> configuration parameter. If the indicated symbol is one from the LUFA
- * library, you may be missing a LUFA source makefile module (see \ref Page_BuildModule_SOURCES).</td>
- * </tr>
- * </table>
- *
- * For troubleshooting other errors you encounter, please see \ref Sec_ProjectHelp.
- */
+/** \file + * + * This file contains special DoxyGen information for the generation of the main page and other special + * documentation pages. It is not a project source file. + */ + +/** \page Page_BuildSystem The LUFA Build System + * + * \section Sec_BuildSystem_Overview Overview of the LUFA Build System + * The LUFA build system is an attempt at making a set of re-usable, modular build make files which + * can be referenced in a LUFA powered project, to minimize the amount of code required in an + * application makefile. The system is written in GNU Make, and each module is independent of + * one-another. + * + * For details on the prerequisites needed for Linux and Windows machines to be able to use the LUFA + * build system, see \ref Sec_CompilingApps_Prerequisites. + * + * To use a LUFA build system module, simply add an include to your project makefile. All user projects + * should at a minimum include \ref Page_BuildModule_CORE for base functionality: + * \code + * include $(LUFA_PATH)/Build/lufa_core.mk + * \endcode + * + * Once included in your project makefile, the associated build module targets will be added to your + * project's build makefile targets automatically. To call a build target, run <tt>make {TARGET_NAME}</tt> + * from the command line, substituting in the appropriate target name. + * + * \see \ref Sec_ConfiguringApps_AppMakefileParams for a copy of the sample LUFA project makefile. + * + * Each build module may have one or more mandatory parameters (GNU Make variables) which <i>must</i> + * be supplied in the project makefile for the module to work, and one or more optional parameters which + * may be defined and which will assume a sensible default if not. + * + * \section SSec_BuildSystem_Modules Available Modules + * + * The following modules are included in this LUFA release: + * + * \li \subpage Page_BuildModule_ATPROGRAM - Device Programming + * \li \subpage Page_BuildModule_AVRDUDE - Device Programming + * \li \subpage Page_BuildModule_BUILD - Compiling/Assembling/Linking + * \li \subpage Page_BuildModule_CORE - Core Build System Functions + * \li \subpage Page_BuildModule_CPPCHECK - Static Code Analysis + * \li \subpage Page_BuildModule_DFU - Device Programming + * \li \subpage Page_BuildModule_DOXYGEN - Automated Source Code Documentation + * \li \subpage Page_BuildModule_HID - Device Programming + * \li \subpage Page_BuildModule_SOURCES - LUFA Module Source Code Variables + * + * If you have problems building using the LUFA build system, see \subpage Page_BuildTroubleshooting for resolution steps. + */ + + /** \page Page_BuildModule_BUILD The BUILD build module + * + * The BUILD LUFA build system module, providing targets for the compilation, + * assembling and linking of an application from source code into binary files + * suitable for programming into a target device, using the GCC compiler. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_build.mk + * \endcode + * + * \section SSec_BuildModule_BUILD_Requirements Requirements + * This module requires the the architecture appropriate binaries of the GCC compiler are available in your + * system's <b>PATH</b> variable. The GCC compiler and associated toolchain is distributed in Atmel AVR Studio + * 5.x and Atmel Studio 6.x installation directories, as well as in many third party distribution packages. + * + * \section SSec_BuildModule_BUILD_Targets Targets + * + * <table> + * <tr> + * <td><tt>size</tt></td> + * <td>Display size of the compiled application FLASH and SRAM segments.</td> + * </tr> + * <tr> + * <td><tt>symbol-sizes</tt></td> + * <td>Display a size-sorted list of symbols from the compiled application, in decimal bytes.</td> + * </tr> + * <tr> + * <td><tt>lib</tt></td> + * <td>Build and archive all source files into a library A binary file.</td> + * </tr> + * <tr> + * <td><tt>all</tt></td> + * <td>Build and link the application into ELF debug and HEX binary files.</td> + * </tr> + * <tr> + * <td><tt>elf</tt></td> + * <td>Build and link the application into an ELF debug file.</td> + * </tr> + * <tr> + * <td><tt>bin</tt></td> + * <td>Build and link the application and produce a BIN binary file.</td> + * </tr> + * <tr> + * <td><tt>hex</tt></td> + * <td>Build and link the application and produce HEX and EEP binary files.</td> + * </tr> + * <tr> + * <td><tt>lss</tt></td> + * <td>Build and link the application and produce a LSS source code/assembly code mixed listing file.</td> + * </tr> + * <tr> + * <td><tt>clean</tt></td> + * <td>Remove all intermediary files and binary output files.</td> + * </tr> + * <tr> + * <td><tt>mostlyclean</tt></td> + * <td>Remove all intermediary files but preserve any binary output files.</td> + * </tr> + * <tr> + * <td><tt><i><filename></i>.s</tt></td> + * <td>Create an assembly listing of a given input C/C++ source file.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_BUILD_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>TARGET</tt></td> + * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td> + * </tr> + * <tr> + * <td><tt>ARCH</tt></td> + * <td>Architecture of the target processor (see \ref Page_DeviceSupport).</td> + * </tr> + * <tr> + * <td><tt>MCU</tt></td> + * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td> + * </tr> + * <tr> + * <td><tt>SRC</tt></td> + * <td>List of relative or absolute paths to the application C (.c), C++ (.cpp) and Assembly (.S) source files.</td> + * </tr> + * <tr> + * <td><tt>F_USB</tt></td> + * <td>Speed in Hz of the input clock frequency to the target's USB controller.</td> + * </tr> + * <tr> + * <td><tt>LUFA_PATH</tt></td> + * <td>Path to the LUFA library core, either relative or absolute (e.g. <tt>../LUFA-000000/LUFA/</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_BUILD_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><tt>BOARD</tt></td> + * <td>LUFA board hardware drivers to use (see \ref Page_DeviceSupport).</td> + * </tr> + * <tr> + * <td><tt>OPTIMIZATION</tt></td> + * <td>Optimization level to use when compiling source files (see GCC manual).</td> + * </tr> + * <tr> + * <td><tt>C_STANDARD</tt></td> + * <td>Version of the C standard to apply when compiling C++ source files (see GCC manual).</td> + * </tr> + * <tr> + * <td><tt>CPP_STANDARD</tt></td> + * <td>Version of the C++ standard to apply when compiling C++ source files (see GCC manual).</td> + * </tr> + * <tr> + * <td><tt>DEBUG_FORMAT</tt></td> + * <td>Format of the debug information to embed in the generated object files (see GCC manual).</td> + * </tr> + * <tr> + * <td><tt>DEBUG_LEVEL</tt></td> + * <td>Level of the debugging information to embed in the generated object files (see GCC manual).</td> + * </tr> + * <tr> + * <td><tt>F_CPU</tt></td> + * <td>Speed of the processor CPU clock, in Hz.</td> + * </tr> + * <tr> + * <td><tt>C_FLAGS</tt></td> + * <td>Flags to pass to the C compiler only, after the automatically generated flags.</td> + * </tr> + * <tr> + * <td><tt>CPP_FLAGS</tt></td> + * <td>Flags to pass to the C++ compiler only, after the automatically generated flags.</td> + * </tr> + * <tr> + * <td><tt>ASM_FLAGS</tt></td> + * <td>Flags to pass to the assembler only, after the automatically generated flags.</td> + * </tr> + * <tr> + * <td><tt>CC_FLAGS</tt></td> + * <td>Common flags to pass to the C/C++ compiler and assembler, after the automatically generated flags.</td> + * </tr> + * <tr> + * <td><tt>COMPILER_PATH</tt></td> + * <td>Directory where the C/C++ toolchain is located, if not available in the system <tt>PATH</tt>.</td> + * </tr> + * <tr> + * <td><tt>LD_FLAGS</tt></td> + * <td>Flags to pass to the linker, after the automatically generated flags.</td> + * </tr> + * <tr> + * <td><tt>LINKER_RELAXATIONS</tt></td> + * <td>Enables or disables linker relaxations when linking the application binary. This can reduce the total size + * of the application by replacing full \c CALL instructions with smaller \c RCALL instructions where possible. + * \note On some unpatched versions of binutils, this can cause link failures in some circumstances. If you + * receive a link error <tt>relocation truncated to fit: R_AVR_13_PCREL</tt>, disable this setting.</td> + * </tr> + * <tr> + * <td><tt>OBJDIR</tt></td> + * <td>Directory to place the generated object and dependency files. If set to "." the same folder as the source file will be used. + * \note When this option is enabled, all source filenames <b>must</b> be unique.</td> + * </tr> + * <tr> + * <td><tt>OBJECT_FILES</tt></td> + * <td>List of additional object files that should be linked into the resulting binary.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_BUILD_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_BUILD_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + +/** \page Page_BuildModule_CORE The CORE build module + * + * The core LUFA build system module, providing common build system help and information targets. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_core.mk + * \endcode + * + * \section SSec_BuildModule_CORE_Requirements Requirements + * This module has no requirements outside a standard *nix shell like environment; the <tt>sh</tt> + * shell, GNU <tt>make</tt> and *nix CoreUtils (<tt>echo</tt>, <tt>printf</tt>, etc.). + * + * \section SSec_BuildModule_CORE_Targets Targets + * + * <table> + * <tr> + * <td><tt>help</tt></td> + * <td>Display build system help and configuration information.</td> + * </tr> + * <tr> + * <td><tt>list_targets</tt></td> + * <td>List all available build targets from the build system.</td> + * </tr> + * <tr> + * <td><tt>list_modules</tt></td> + * <td>List all available build modules from the build system.</td> + * </tr> + * <tr> + * <td><tt>list_mandatory</tt></td> + * <td>List all mandatory parameters required by the included modules.</td> + * </tr> + * <tr> + * <td><tt>list_optional</tt></td> + * <td>List all optional parameters required by the included modules.</td> + * </tr> + * <tr> + * <td><tt>list_provided</tt></td> + * <td>List all variables provided by the included modules.</td> + * </tr> + * <tr> + * <td><tt>list_macros</tt></td> + * <td>List all macros provided by the included modules.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CORE_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CORE_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CORE_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CORE_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + +/** \page Page_BuildModule_ATPROGRAM The ATPROGRAM build module + * + * The ATPROGRAM programming utility LUFA build system module, providing targets to reprogram an + * Atmel processor FLASH and EEPROM memories with a project's compiled binary output files. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_atprogram.mk + * \endcode + * + * \section SSec_BuildModule_ATPROGRAM_Requirements Requirements + * This module requires the <tt>atprogram.exe</tt> utility to be available in your system's <b>PATH</b> + * variable. The <tt>atprogram.exe</tt> utility is distributed in Atmel AVR Studio 5.x and Atmel Studio 6.x + * inside the application install folder's "\atbackend" subdirectory. + * + * \section SSec_BuildModule_ATPROGRAM_Targets Targets + * + * <table> + * <tr> + * <td><tt>atprogram</tt></td> + * <td>Program the device FLASH memory with the application's executable data.</td> + * </tr> + * <tr> + * <td><tt>atprogram-ee</tt></td> + * <td>Program the device EEPROM memory with the application's EEPROM data.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_ATPROGRAM_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>MCU</tt></td> + * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td> + * </tr> + * <tr> + * <td><tt>TARGET</tt></td> + * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_ATPROGRAM_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><tt>ATPROGRAM_PROGRAMMER</tt></td> + * <td>Name of the Atmel programmer or debugger tool to communicate with (e.g. <tt>jtagice3</tt>).</td> + * </tr> + * <tr> + * <td><tt>ATPROGRAM_INTERFACE</tt></td> + * <td>Name of the programming interface to use when programming the target (e.g. <tt>spi</tt>).</td> + * </tr> + * <tr> + * <td><tt>ATPROGRAM_PORT</tt></td> + * <td>Name of the communication port to use when when programming with a serially connected tool (e.g. <tt>COM2</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_ATPROGRAM_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_ATPROGRAM_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + +/** \page Page_BuildModule_AVRDUDE The AVRDUDE build module + * + * The AVRDUDE programming utility LUFA build system module, providing targets to reprogram an + * Atmel processor FLASH and EEPROM memories with a project's compiled binary output files. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_avrdude.mk + * \endcode + * + * \section SSec_BuildModule_AVRDUDE_Requirements Requirements + * This module requires the <tt>avrdude</tt> utility to be available in your system's <b>PATH</b> + * variable. The <tt>avrdude</tt> utility is distributed in the old WinAVR project releases for + * Windows (<a>http://winavr.sourceforge.net</a>) or can be installed on *nix systems via the project's + * source code (<a>https://savannah.nongnu.org/projects/avrdude</a>) or through the package manager. + * + * \section SSec_BuildModule_AVRDUDE_Targets Targets + * + * <table> + * <tr> + * <td><tt>avrdude</tt></td> + * <td>Program the device FLASH memory with the application's executable data.</td> + * </tr> + * <tr> + * <td><tt>avrdude-ee</tt></td> + * <td>Program the device EEPROM memory with the application's EEPROM data.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_AVRDUDE_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>MCU</tt></td> + * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td> + * </tr> + * <tr> + * <td><tt>TARGET</tt></td> + * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_AVRDUDE_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><tt>AVRDUDE_PROGRAMMER</tt></td> + * <td>Name of the programmer or debugger tool to communicate with (e.g. <tt>jtagicemkii</tt>).</td> + * </tr> + * <tr> + * <td><tt>AVRDUDE_PORT</tt></td> + * <td>Name of the communication port to use when when programming with the connected tool (e.g. <tt>COM2</tt>, <tt>/dev/ttyUSB0</tt> or <tt>usb</tt>).</td> + * </tr> + * <tr> + * <td><tt>AVRDUDE_FLAGS</tt></td> + * <td>Additional flags to pass to avrdude when programming, applied after the automatically generated flags.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_AVRDUDE_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_AVRDUDE_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + + /** \page Page_BuildModule_CPPCHECK The CPPCHECK build module + * + * The CPPCHECK programming utility LUFA build system module, providing targets to statically + * analyze C and C++ source code for errors and performance/style issues. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_cppcheck.mk + * \endcode + * + * \section SSec_BuildModule_CPPCHECK_Requirements Requirements + * This module requires the <tt>cppcheck</tt> utility to be available in your system's <b>PATH</b> + * variable. The <tt>cppcheck</tt> utility is distributed through the project's home page + * (<a>http://cppcheck.sourceforge.net</a>) for Windows, and can be installed on *nix systems via + * the project's source code or through the package manager. + * + * \section SSec_BuildModule_CPPCHECK_Targets Targets + * + * <table> + * <tr> + * <td><tt>cppcheck</tt></td> + * <td>Statically analyze the project source code for issues.</td> + * </tr> + * <tr> + * <td><tt>cppcheck-config</tt></td> + * <td>Check the <tt>cppcheck</tt> configuration - scan source code and warn about missing header files and other issues.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CPPCHECK_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>SRC</tt></td> + * <td>List of source files to statically analyze.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CPPCHECK_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><tt>CPPCHECK_INCLUDES</tt></td> + * <td>Path of extra directories to check when attemting to resolve C/C++ header file includes.</td> + * </tr> + * <tr> + * <td><tt>CPPCHECK_EXCLUDES</tt></td> + * <td>Paths or path fragments to exclude when analyzing.</td> + * </tr> + * <tr> + * <td><tt>CPPCHECK_MSG_TEMPLATE</tt></td> + * <td>Output message template to use when printing errors, warnings and information (see <tt>cppcheck</tt> documentation).</td> + * </tr> + * <tr> + * <td><tt>CPPCHECK_ENABLE</tt></td> + * <td>Analysis rule categories to enable (see <tt>cppcheck</tt> documentation).</td> + * </tr> + * <tr> + * <td><tt>CPPCHECK_SUPPRESS</tt></td> + * <td>Specific analysis rules to suppress (see <tt>cppcheck</tt> documentation).</td> + * </tr> + * <tr> + * <td><tt>CPPCHECK_FAIL_ON_WARNING</tt></td> + * <td>Set to <b>Y</b> to fail the analysis job with an error exit code if warnings are found, <b>N</b> to continue without failing.</td> + * </tr> + * <tr> + * <td><tt>CPPCHECK_QUIET</tt></td> + * <td>Set to <b>Y</b> to suppress all output except warnings and errors, <b>N</b> to show verbose output information.</td> + * </tr> + * <tr> + * <td><tt>CPPCHECK_FLAGS</tt></td> + * <td>Extra flags to pass to <tt>cppcheck</tt>, after the automatically generated flags.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CPPCHECK_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_CPPCHECK_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + + /** \page Page_BuildModule_DFU The DFU build module + * + * The DFU programming utility LUFA build system module, providing targets to reprogram an + * Atmel processor FLASH and EEPROM memories with a project's compiled binary output files. + * This module requires a DFU class bootloader to be running in the target, compatible with + * the DFU bootloader protocol as published by Atmel. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_dfu.mk + * \endcode + * + * \section SSec_BuildModule_DFU_Requirements Requirements + * This module requires either the <tt>batchisp</tt> utility from Atmel's FLIP utility, or the open + * source <tt>dfu-programmer</tt> utility (<a>http://dfu-programmer.sourceforge.net/</a>) to be + * available in your system's <b>PATH</b> variable. On *nix systems the <tt>dfu-programmer</tt> utility + * can be installed via the project's source code or through the package manager. + * + * \section SSec_BuildModule_DFU_Targets Targets + * + * <table> + * <tr> + * <td><tt>dfu</tt></td> + * <td>Program the device FLASH memory with the application's executable data using <tt>dfu-programmer</tt>.</td> + * </tr> + * <tr> + * <td><tt>dfu-ee</tt></td> + * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>dfu-programmer</tt>.</td> + * </tr> + * <tr> + * <td><tt>flip</tt></td> + * <td>Program the device FLASH memory with the application's executable data using <tt>batchisp</tt>.</td> + * </tr> + * <tr> + * <td><tt>flip-ee</tt></td> + * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>batchisp</tt>.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DFU_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>MCU</tt></td> + * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td> + * </tr> + * <tr> + * <td><tt>TARGET</tt></td> + * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DFU_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DFU_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DFU_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + + /** \page Page_BuildModule_DOXYGEN The DOXYGEN build module + * + * The DOXYGEN code documentation utility LUFA build system module, providing targets to generate + * project HTML and other format documentation from a set of source files that include special + * Doxygen comments. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_doxygen.mk + * \endcode + * + * \section SSec_BuildModule_DOXYGEN_Requirements Requirements + * This module requires the <tt>doxygen</tt> utility from the Doxygen website + * (<a>http://www.doxygen.org/</a>) to be available in your system's <b>PATH</b> variable. On *nix + * systems the <tt>doxygen</tt> utility can be installed via the project's source code or through + * the package manager. + * + * \section SSec_BuildModule_DOXYGEN_Targets Targets + * + * <table> + * <tr> + * <td><tt>doxygen</tt></td> + * <td>Generate project documentation.</td> + * </tr> + * <tr> + * <td><tt>doxygen_create</tt></td> + * <td>Create a new Doxygen configuration file using the latest template.</td> + * </tr> + * <tr> + * <td><tt>doxygen_upgrade</tt></td> + * <td>Upgrade an existing Doxygen configuration file to the latest template</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DOXYGEN_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>LUFA_PATH</tt></td> + * <td>Path to the LUFA library core, either relative or absolute (e.g. <tt>../LUFA-000000/LUFA/</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DOXYGEN_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><tt>DOXYGEN_CONF</tt></td> + * <td>Name and path of the base Doxygen configuration file for the project.</td> + * </tr> + * <tr> + * <td><tt>DOXYGEN_FAIL_ON_WARNING</tt></td> + * <td>Set to <b>Y</b> to fail the generation with an error exit code if warnings are found other than unsupported configuration parameters, <b>N</b> to continue without failing.</td> + * </tr> + * <tr> + * <td><tt>DOXYGEN_OVERRIDE_PARAMS</tt></td> + * <td>Extra Doxygen configuration parameters to apply, overriding the corresponding config entry in the project's configuration file (e.g. <tt>QUIET=YES</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DOXYGEN_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_DOXYGEN_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + + /** \page Page_BuildModule_HID The HID build module + * + * The HID programming utility LUFA build system module, providing targets to reprogram an + * Atmel processor's FLASH memory with a project's compiled binary output file. This module + * requires a HID class bootloader to be running in the target, using a protocol compatible + * with the PJRC "HalfKay" protocol (<a>http://www.pjrc.com/teensy/halfkay_protocol.html</a>). + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_hid.mk + * \endcode + * + * \section SSec_BuildModule_HID_Requirements Requirements + * This module requires either the <tt>hid_bootloader_cli</tt> utility from the included LUFA HID + * class bootloader API subdirectory, or the <tt>teensy_loader_cli</tt> utility from PJRC + * (<a>http://www.pjrc.com/teensy/loader_cli.html</a>) to be available in your system's <b>PATH</b> + * variable. + * + * \section SSec_BuildModule_HID_Targets Targets + * + * <table> + * <tr> + * <td><tt>hid</tt></td> + * <td>Program the device FLASH memory with the application's executable data using <tt>hid_bootloader_cli</tt>.</td> + * </tr> + * <tr> + * <td><tt>hid-ee</tt></td> + * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>hid_bootloader_cli</tt> and + * a temporary AVR application programmed into the target's FLASH. + * \note This will erase the currently loaded application in the target.</td> + * </tr> + * <tr> + * <td><tt>teensy</tt></td> + * <td>Program the device FLASH memory with the application's executable data using <tt>teensy_loader_cli</tt>.</td> + * </tr> + * <tr> + * <td><tt>teensy-ee</tt></td> + * <td>Program the device EEPROM memory with the application's EEPROM data using <tt>teensy_loader_cli</tt> and + * a temporary AVR application programmed into the target's FLASH. + * \note This will erase the currently loaded application in the target.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_HID_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>MCU</tt></td> + * <td>Name of the Atmel processor model (e.g. <tt>at90usb1287</tt>).</td> + * </tr> + * <tr> + * <td><tt>TARGET</tt></td> + * <td>Name of the application output file prefix (e.g. <tt>TestApplication</tt>).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_HID_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_HID_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_HID_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + + /** \page Page_BuildModule_SOURCES The SOURCES build module + * + * The SOURCES LUFA build system module, providing variables listing the various LUFA source files + * required to be build by a project for a given LUFA module. This module gives a way to reference + * LUFA source files symbolically, so that changes to the library structure do not break the library + * makefile. + * + * To use this module in your application makefile, add the following code: + * \code + * include $(LUFA_PATH)/Build/lufa_sources.mk + * \endcode + * + * \section SSec_BuildModule_SOURCES_Requirements Requirements + * None. + * + * \section SSec_BuildModule_SOURCES_Targets Targets + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_SOURCES_MandatoryParams Mandatory Parameters + * + * <table> + * <tr> + * <td><tt>LUFA_PATH</tt></td> + * <td>Path to the LUFA library core, either relative or absolute (e.g. <tt>../LUFA-000000/LUFA/</tt>).</td> + * </tr> + * <tr> + * <td><tt>ARCH</tt></td> + * <td>Architecture of the target processor (see \ref Page_DeviceSupport).</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_SOURCES_OptionalParams Optional Parameters + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + * + * \section SSec_BuildModule_SOURCES_ProvidedVariables Module Provided Variables + * + * <table> + * <tr> + * <td><tt>LUFA_SRC_USB</tt></td> + * <td>List of LUFA USB driver source files.</td> + * </tr> + * <tr> + * <td><tt>LUFA_SRC_USBCLASS</tt></td> + * <td>List of LUFA USB Class driver source files.</td> + * </tr> + * <tr> + * <td><tt>LUFA_SRC_TEMPERATURE</tt></td> + * <td>List of LUFA temperature sensor driver source files.</td> + * </tr> + * <tr> + * <td><tt>LUFA_SRC_SERIAL</tt></td> + * <td>List of LUFA Serial U(S)ART driver source files.</td> + * </tr> + * <tr> + * <td><tt>LUFA_SRC_TWI</tt></td> + * <td>List of LUFA TWI driver source files.</td> + * </tr> + * <tr> + * <td><tt>LUFA_SRC_PLATFORM</tt></td> + * <td>List of LUFA architecture specific platform management source files.</td> + * </tr> + * </table> + * + * \section SSec_BuildModule_SOURCES_ProvidedMacros Module Provided Macros + * + * <table> + * <tr> + * <td><i>None</i></td> + * </tr> + * </table> + */ + +/** \page Page_BuildTroubleshooting Troubleshooting Information + * + * LUFA uses a lot of advanced features of the AVR-GCC compiler, linker, and surrounding binaries. This can sometimes lead to problems compiling applications if one of these + * features is buggy in the version of the tools used in a build environment. Missing utilities and incorrectly set makefile configuration options can also result in different + * errors being produced when compilation or other operations are attempted. The table below lists a set of commonly encountered errors and their resolutions. + * + * <table> + * <tr> + * <th>Problem</th> + * <th>Resolution</th> + * </tr> + * <tr> + * <td>Error "<b><tt>relocation truncated to fit: R_AVR_13_PCREL against symbol <i>{X}</i></tt></b>" shown when compiling.</td> + * <td>Try compiling with the setting <tt>LINKER_RELAXATIONS=N</tt> in your LUFA Build System 2.0 makefile, or remove the line <tt>-Wl,--relax</tt> + * from other makefiles. Alternatively, make sure you have the latest version of the Atmel Toolchain installed for your system.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>error: ld terminated with signal 11 [Segmentation fault]</tt></b>" shown when compiling.</td> + * <td>Try compiling with the setting <tt>DEBUG_LEVEL=2</tt> in your LUFA Build System 2.0 makefile, or make sure you are using <tt>binutils</tt> version 2.22 or later.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>EMERGENCY ABORT: INFINITE RECURSION DETECTED</tt></b>" shown when compiling.</td> + * <td>Make sure you are using an up to date version of GNU Make when compiling. This error is a safety system added to the mid-level makefiles, to prevent an issue with + * GNU make or other variants of Make causing an infinitely recursive build.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Unsupported architecture "<i>{X}</i>"</tt></b>" shown when compiling.</td> + * <td>Ensure your makefile's <tt>ARCH</tt> setting is set to one of the architecture names (case-sensitive) supported by the version of LUFA you are compiling against.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Makefile <i>{X}</i> value not set</tt></b>" shown when compiling.</td> + * <td>The specified Makefile value was not configured in your project's makefile or on the command line, and the nominated setting is required by one or more LUFA + * build system modules. Define the value in your project makefile and try again.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Makefile <i>{X}</i> option cannot be blank</tt></b>" shown when compiling.</td> + * <td>The specified Makefile value was configured in your project's makefile or on the command line, but was set to an empty value. For the nominated configuration + * option, an empty value is not allowed. Define the nominated setting to a correct non-blank value and try again.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Makefile <i>{X}</i> option must be Y or N</tt></b>" shown when compiling.</td> + * <td>The specified Makefile value was configured in your project's makefile or on the command line, but was set to a value other than a Y (for "Yes") or "N" (for "No"). + * This configuration option is required to be one of the aforementioned boolean values, and other values are invalid. Set this option to either Y or N and try again.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Unknown input source file formats: <i>{X}</i></tt></b>" shown when compiling.</td> + * <td>The nominated source files, specified in your project's makefile in the <tt>SRC</tt> configuration option, has an extension that the LUFA build system does not + * recognise. The file extensions are case sensitive, and must be one of the supported formats (<tt>*.c</tt>, <tt>*.cpp</tt> or <tt>*.S</tt>).</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Cannot build with OBJDIR parameter set - one or more object file name is not unique</tt></b>" shown when compiling.</td> + * <td>When a project is built with a non-empty <tt>OBJDIR</tt> object directory name set, all input source files must have unique names, excluding extension and path. + * This means that input files that are named identically and differ only by their path or extension are invalid when this mode is used.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Source file does not exist: <i>{X}</i></tt></b>" shown when compiling.</td> + * <td>The nominated input source file, specified in the user project's <tt>SRC</tt> parameter, could not be found. Ensure the source file exists and the absolute or + * relative path given in the user project makefile is correct and try again.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>Doxygen configuration file <i>{X}</i> does not exist</tt></b>" shown when upgrading a Doxygen configuration file.</td> + * <td>The nominated Doxygen configuration file, specified in the user project's <tt>DOXYGEN_CONF</tt> parameter, could not be found. Ensure the configuration file exists + * and the absolute or relative path given in the user project makefile is correct and try again, or run the appropriate makefile target to generate a new configuration + * file.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>avr-gcc: error: unrecognized option '<i>{X}</i>'</tt></b>" shown when compiling.</td> + * <td>An unrecognised option was supplied to the compiler, usually in the <tt>C_FLAGS</tt>, <tt>CPP_FLAGS</tt>, <tt>ASM_FLAGS</tt> or <tt>CC_FLAGS</tt> configuration + * options. The nominated compiler switch may be invalid, or unsupported by the version of AVR-GCC on the host system. Remove the unrecognised flag if invalid, or + * upgrade to the latest AVR-GCC. If the option is a valid linker option, use the prefix "-Wl," to ensure it is passed to the linker correctly.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>makefile:{X}: {Y}.mk: No such file or directory</tt></b>" shown when make is invoked.</td> + * <td>The path to the nominated makefile module was incorrect. This usually indicates that the makefile <tt>LUFA_PATH</tt> option is not set to a valid relative or + * absolute path to the LUFA library core.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>fatal error: LUFAConfig.h: No such file or directory</tt></b>" shown when compiling.</td> + * <td>The <tt>USE_LUFA_CONFIG_HEADER</tt> compile time option was set in the user project makefile, but the user supplied <tt>LUFAConfig.h</tt> header could not be + * found. Ensure that the directory that contains this configuration file is correctly passed to the compiler via the -I switch in the makefile <tt>CC_FLAGS</tt> + * parameter.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>ld.exe: section .apitable_trampolines loaded at <i>{X}</i> overlaps section .text</tt></b>" shown when compiling a bootloader.</td> + * <td>The bootloader is compiling too large for the given <tt>FLASH_SIZE_KB</tt> and <tt>BOOT_SECTION_SIZE_KB</tt> parameters set in the bootloader makefile. This + * usually indicates that these values are incorrect for the specified device the bootloader is targeting. If these values are correct, a newer version of the + * compiler may need to be used to ensure that the bootloader is built within the section size constraints of the target device.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>unknown MCU '<i>{X}</i>' specified</tt></b>" shown when compiling.</td> + * <td>The specified microcontroller device model name set in the user application's makefile as the <tt>MCU</tt> parameter is incorrect, or unsupported by the + * version of the compiler being used. Make sure the model name is correct, or upgrade to the latest Atmel Toolchain to obtain newer device support.</td> + * </tr> + * <tr> + * <td>Error "<b><tt>undefined reference to `<i>{X}</i>'</tt></b>" shown when compiling.</td> + * <td>This is usually caused by a missing source file in the user application's <tt>SRC</tt> configuration parameter. If the indicated symbol is one from the LUFA + * library, you may be missing a LUFA source makefile module (see \ref Page_BuildModule_SOURCES).</td> + * </tr> + * </table> + * + * For troubleshooting other errors you encounter, please see \ref Sec_ProjectHelp. + */ |