1 files changed, 0 insertions, 76 deletions
diff --git a/keyboards/infinity_ergodox/infinity_ergodox.c b/keyboards/infinity_ergodox/infinity_ergodox.c
deleted file mode 100644
index 87ed40fabf..0000000000
--- a/keyboards/infinity_ergodox/infinity_ergodox.c
+++ /dev/null
@@ -1,76 +0,0 @@
-#include "infinity_ergodox.h"
-#include "ch.h"
-#include "hal.h"
-#include "serial_link/system/serial_link.h"
-#include "lcd_backlight.h"
-
-void init_serial_link_hal(void) {
-    PORTA->PCR[1] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(2);
-    PORTA->PCR[2] = PORTx_PCRn_DSE | PORTx_PCRn_SRE | PORTx_PCRn_MUX(2);
-    PORTE->PCR[0] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(3);
-    PORTE->PCR[1] = PORTx_PCRn_DSE | PORTx_PCRn_SRE | PORTx_PCRn_MUX(3);
-}
-
-#define RED_PIN 1
-#define GREEN_PIN 2
-#define BLUE_PIN 3
-#define CHANNEL_RED FTM0->CHANNEL[0]
-#define CHANNEL_GREEN FTM0->CHANNEL[1]
-#define CHANNEL_BLUE FTM0->CHANNEL[2]
-
-#define RGB_PORT PORTC
-#define RGB_PORT_GPIO GPIOC
-
-// Base FTM clock selection (72 MHz system clock)
-// @ 0xFFFF period, 72 MHz / (0xFFFF * 2) = Actual period
-// Higher pre-scalar will use the most power (also look the best)
-// Pre-scalar calculations
-// 0 -      72 MHz -> 549 Hz
-// 1 -      36 MHz -> 275 Hz
-// 2 -      18 MHz -> 137 Hz
-// 3 -       9 MHz ->  69 Hz (Slightly visible flicker)
-// 4 -   4 500 kHz ->  34 Hz (Visible flickering)
-// 5 -   2 250 kHz ->  17 Hz
-// 6 -   1 125 kHz ->   9 Hz
-// 7 - 562 500  Hz ->   4 Hz
-// Using a higher pre-scalar without flicker is possible but FTM0_MOD will need to be reduced
-// Which will reduce the brightness range
-#define PRESCALAR_DEFINE 0
-
-void lcd_backlight_hal_init(void) {
-	// Setup Backlight
-    SIM->SCGC6 |= SIM_SCGC6_FTM0;
-    FTM0->CNT = 0; // Reset counter
-
-	// PWM Period
-	// 16-bit maximum
-	FTM0->MOD = 0xFFFF;
-
-	// Set FTM to PWM output - Edge Aligned, Low-true pulses
-#define CNSC_MODE FTM_SC_CPWMS | FTM_SC_PS(4) | FTM_SC_CLKS(0)
-	CHANNEL_RED.CnSC = CNSC_MODE;
-	CHANNEL_GREEN.CnSC = CNSC_MODE;
-	CHANNEL_BLUE.CnSC = CNSC_MODE;
-
-	// System clock, /w prescalar setting
-	FTM0->SC = FTM_SC_CLKS(1) | FTM_SC_PS(PRESCALAR_DEFINE);
-
-	CHANNEL_RED.CnV = 0;
-	CHANNEL_GREEN.CnV = 0;
-	CHANNEL_BLUE.CnV = 0;
-
-	RGB_PORT_GPIO->PDDR |= (1 << RED_PIN);
-	RGB_PORT_GPIO->PDDR |= (1 << GREEN_PIN);
-	RGB_PORT_GPIO->PDDR |= (1 << BLUE_PIN);
-
-#define RGB_MODE PORTx_PCRn_SRE | PORTx_PCRn_DSE | PORTx_PCRn_MUX(4)
-    RGB_PORT->PCR[RED_PIN] = RGB_MODE;
-    RGB_PORT->PCR[GREEN_PIN] = RGB_MODE;
-    RGB_PORT->PCR[BLUE_PIN] = RGB_MODE;
-}
-
-void lcd_backlight_hal_color(uint16_t r, uint16_t g, uint16_t b) {
-	CHANNEL_RED.CnV = r;
-	CHANNEL_GREEN.CnV = g;
-	CHANNEL_BLUE.CnV = b;
-}