diff options
Diffstat (limited to 'keyboards/cluepad')
| -rw-r--r-- | keyboards/cluepad/Makefile | 71 | ||||
| -rw-r--r-- | keyboards/cluepad/config.h | 2 | ||||
| -rw-r--r-- | keyboards/cluepad/readme.md | 4 | ||||
| -rw-r--r-- | keyboards/cluepad/rules.mk | 65 |
4 files changed, 72 insertions, 70 deletions
diff --git a/keyboards/cluepad/Makefile b/keyboards/cluepad/Makefile index a331ff4dcd..4e2a6f00fd 100644 --- a/keyboards/cluepad/Makefile +++ b/keyboards/cluepad/Makefile @@ -1,70 +1,3 @@ - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -# MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -# EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -# CONSOLE_ENABLE ?= yes # Console for debug(+400) -# COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= yes # Enable numpad's backlight functionality -RGBLIGHT_ENABLE ?= yes -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif +endif
\ No newline at end of file diff --git a/keyboards/cluepad/config.h b/keyboards/cluepad/config.h index bae05fade3..bd64dfd27d 100644 --- a/keyboards/cluepad/config.h +++ b/keyboards/cluepad/config.h @@ -70,7 +70,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* Underlight configuration */ #define RGB_DI_PIN F6 -#define RGBLIGHT_TIMER +#define RGBLIGHT_ANIMATIONS #define RGBLED_NUM 4 // Number of LEDs #define RGBLIGHT_HUE_STEP 10 #define RGBLIGHT_SAT_STEP 17 diff --git a/keyboards/cluepad/readme.md b/keyboards/cluepad/readme.md new file mode 100644 index 0000000000..8450340f27 --- /dev/null +++ b/keyboards/cluepad/readme.md @@ -0,0 +1,4 @@ +Cluepad number pad firmware +====================== + +TODO: to be updated. diff --git a/keyboards/cluepad/rules.mk b/keyboards/cluepad/rules.mk new file mode 100644 index 0000000000..19b16b95a9 --- /dev/null +++ b/keyboards/cluepad/rules.mk @@ -0,0 +1,65 @@ + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +# MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +# EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable numpad's backlight functionality +RGBLIGHT_ENABLE ?= yes +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
\ No newline at end of file |