diff options
Diffstat (limited to 'keyboard/lightsaber/Makefile.lufa')
| -rw-r--r-- | keyboard/lightsaber/Makefile.lufa | 126 |
1 files changed, 0 insertions, 126 deletions
diff --git a/keyboard/lightsaber/Makefile.lufa b/keyboard/lightsaber/Makefile.lufa deleted file mode 100644 index 99090c4367..0000000000 --- a/keyboard/lightsaber/Makefile.lufa +++ /dev/null @@ -1,126 +0,0 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# Target file name (without extension). -TARGET = lightsaber_lufa - -# Directory common source filess exist -TMK_DIR = ../../tmk_core - -# Directory keyboard dependent files exist -TARGET_DIR = . - - -# List C source files here. (C dependencies are automatically generated.) -SRC = keymap.c \ - matrix.c \ - led.c \ - backlight.c - -CONFIG_H = config.h - - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 8000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -#MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality - - -# Boot Section Size in bytes -# Teensy halfKay 512 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(TMK_DIR) - -include $(TMK_DIR)/protocol/lufa.mk -include $(TMK_DIR)/common.mk -include $(TMK_DIR)/rules.mk - -winkey: OPT_DEFS += -DLAYOUT_WINKEY -winkey: all |