diff options
Diffstat (limited to 'converter/m0110_usb/Makefile.tmk_rev2')
| -rw-r--r-- | converter/m0110_usb/Makefile.tmk_rev2 | 96 |
1 files changed, 0 insertions, 96 deletions
diff --git a/converter/m0110_usb/Makefile.tmk_rev2 b/converter/m0110_usb/Makefile.tmk_rev2 deleted file mode 100644 index e836456326..0000000000 --- a/converter/m0110_usb/Makefile.tmk_rev2 +++ /dev/null @@ -1,96 +0,0 @@ -# Target file name (without extension). -TARGET = m0110_lufa - -# Directory common source filess exist -TMK_DIR = ../../tmk_core - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# keyboard dependent files -SRC = matrix.c \ - led.c \ - keymap_common.c \ - m0110.c - -# To use own keymap file run make like: make keymap=hasu -ifdef KEYMAP - SRC += keymap_$(KEYMAP).c -else - SRC += keymap_default.c -endif - -CONFIG_H = config.h - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -MCU = atmega32u2 # TMK converter rev2 -#MCU = atmega32u4 # TMK converter rev1 - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in bytes -# Teensy halfKay 512 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# *Comment out* to disable the options. -# -#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA -#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor - - - -#---------------- Programming Options -------------------------- -PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex - - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(TMK_DIR) - - -include $(TMK_DIR)/protocol/lufa.mk -include $(TMK_DIR)/protocol.mk -include $(TMK_DIR)/common.mk -include $(TMK_DIR)/rules.mk |