diff options
Diffstat (limited to 'converter/m0110_usb/Makefile.lufa')
| -rw-r--r-- | converter/m0110_usb/Makefile.lufa | 91 |
1 files changed, 91 insertions, 0 deletions
diff --git a/converter/m0110_usb/Makefile.lufa b/converter/m0110_usb/Makefile.lufa new file mode 100644 index 0000000000..028bdf9331 --- /dev/null +++ b/converter/m0110_usb/Makefile.lufa @@ -0,0 +1,91 @@ +# Target file name (without extension). +TARGET = m0110_lufa + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# keyboard dependent files +SRC = keymap.c \ + matrix.c \ + led.c \ + m0110.c + +CONFIG_H = config.h + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +#MCU = at90usb162 # Teensy 1.0 +MCU = atmega32u4 # Teensy 2.0 +#MCU = at90usb646 # Teensy++ 1.0 +#MCU = at90usb1286 # Teensy++ 2.0 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Build Options +# *Comment out* to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +#NKRO_ENABLE = yes # USB Nkey Rollover + + +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +OPT_DEFS += -DBOOT_SIZE=4096 + + + +#---------------- Programming Options -------------------------- +PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + + +include $(TOP_DIR)/protocol/lufa.mk +include $(TOP_DIR)/protocol.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk + +hasu: EXTRAFLAGS += -DHASU +hasu: all |