diff options
| -rwxr-xr-x | keyboards/zlant/config.h | 58 | ||||
| -rwxr-xr-x | keyboards/zlant/keymaps/default/keymap.c | 20 | ||||
| -rw-r--r-- | keyboards/zlant/keymaps/default/readme.md | 5 | ||||
| -rw-r--r-- | keyboards/zlant/readme.md | 17 | ||||
| -rwxr-xr-x | keyboards/zlant/rules.mk | 56 | ||||
| -rwxr-xr-x | keyboards/zlant/zlant.c | 1 | ||||
| -rwxr-xr-x | keyboards/zlant/zlant.h | 18 |
7 files changed, 175 insertions, 0 deletions
diff --git a/keyboards/zlant/config.h b/keyboards/zlant/config.h new file mode 100755 index 0000000000..456d225aa2 --- /dev/null +++ b/keyboards/zlant/config.h @@ -0,0 +1,58 @@ +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Matthew Cordier +#define PRODUCT Zlant +#define DESCRIPTION keyboard firmware for Zlant + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* key matrix pins */ +#define MATRIX_ROW_PINS { B0, B1, D4, D5 } +#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, B7, D1, D2, D3, B3, B2 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* number of backlight levels */ + +#ifdef BACKLIGHT_PIN +#define BACKLIGHT_LEVELS 0 +#endif + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE + +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* prevent stuck modifiers */ +#define PREVENT_STUCK_MODIFIERS + +#define RGB_DI_PIN D6 +#ifdef RGB_DI_PIN +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 12 +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#endif + +#endif diff --git a/keyboards/zlant/keymaps/default/keymap.c b/keyboards/zlant/keymaps/default/keymap.c new file mode 100755 index 0000000000..d586c841d8 --- /dev/null +++ b/keyboards/zlant/keymaps/default/keymap.c @@ -0,0 +1,20 @@ +#include QMK_KEYBOARD_H + +#define BASE 0 +#define FN 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + [BASE] = LAYOUT( + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, + KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, + KC_ESC, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT, + RGB_HUI, RGB_HUD, KC_LGUI, KC_LALT, KC_LSFT, KC_SPC, KC_SPC, MO(1), KC_LEFT, KC_DOWN, KC_UP, KC_RGHT), + + [FN] = LAYOUT( + KC_TRNS, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_TRNS, + KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS, + KC_TRNS, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, KC_PGUP, KC_HOME, KC_TRNS, KC_TRNS, + RGB_VAI, RGB_VAD, RESET, KC_PSCR, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGDN, KC_END, KC_TRNS, KC_DEL) + +}; diff --git a/keyboards/zlant/keymaps/default/readme.md b/keyboards/zlant/keymaps/default/readme.md new file mode 100644 index 0000000000..968702a16c --- /dev/null +++ b/keyboards/zlant/keymaps/default/readme.md @@ -0,0 +1,5 @@ + + +# Default Zlant Layout + +This is the default layout that comes flashed on the Zlant prototype. diff --git a/keyboards/zlant/readme.md b/keyboards/zlant/readme.md new file mode 100644 index 0000000000..0780cedeb1 --- /dev/null +++ b/keyboards/zlant/readme.md @@ -0,0 +1,17 @@ +# Zlant + + + +A compact 40% inspired by the Plank with a staggered layout instead. + +Keyboard Maintainer: [Felipe Coury](https://github.com/fcoury) + +Hardware Supported: Zlant Prototype PCB + +Hardware Availability: Group buy soon + +Make example for this keyboard (after setting up your build environment): + + make zlant:default + +See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information. diff --git a/keyboards/zlant/rules.mk b/keyboards/zlant/rules.mk new file mode 100755 index 0000000000..482f99b223 --- /dev/null +++ b/keyboards/zlant/rules.mk @@ -0,0 +1,56 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = yes diff --git a/keyboards/zlant/zlant.c b/keyboards/zlant/zlant.c new file mode 100755 index 0000000000..b60e9425c7 --- /dev/null +++ b/keyboards/zlant/zlant.c @@ -0,0 +1 @@ +#include "zlant.h" diff --git a/keyboards/zlant/zlant.h b/keyboards/zlant/zlant.h new file mode 100755 index 0000000000..48c7b3f409 --- /dev/null +++ b/keyboards/zlant/zlant.h @@ -0,0 +1,18 @@ +#ifndef KB_H +#define KB_H + +#include "quantum.h" + +#define LAYOUT( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, \ + K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, \ + K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311 \ +) { \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011 }, \ + { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111 }, \ + { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311 } \ +} + +#endif |