Merge pull request #19 from qmk/master

Merge from qmk 

1 files changed, 58 insertions, 0 deletions

diff --git a/keyboards/handwired/MS-sculpt-mobile/readme.md b/keyboards/handwired/MS-sculpt-mobile/readme.md
new file mode 100644
index 0000000000..d435b449fb
--- /dev/null
+++ b/keyboards/handwired/MS-sculpt-mobile/readme.md
@@ -0,0 +1,58 @@
+
+This is a way to take a Microsoft ergonomic bluetooth keyboard, and make it 
+into a hard-wired keyboard running QMK. 
+
+The keyboard is known under several different names:
+Mobile Bluetooth 5000, Mobile 6000, Sculpt mobile, and Asus rebranded 
+
+I had a stack of them,since they're cheap on ebay, travel well, and are just ergo enough. 
+
+The ribbon cable is 1mm pitch, which is hard to hand solder. I bought a cheap set of 
+"pitch adapter" boards https://www.amazon.com/Double-Sided-0-4mm-1-0-Adapter-60mmx38mm/dp/B00OK42118
+
+Cut the original ribbon cable sockets off the bluetooth board using a razor, they're hard to desolder. 
+They're also allow the cable to be inserted on top or bottom. 
+
+If I was going to do it again, I'd make the MCU connection come out the top of the keyboard
+and avoid the wires dangling out the bottom. 
+
+As I was debugging the matrix, I started to get random failures. In desparation I tried a second MCU, 
+but had the same problems. It turns out that the ribbon cable connections can get worn. Shave a
+half millimeter off the end of the ribbon cable & the errors go away. 
+
+My method for discovering the matrix was to set up a KEYMAP macro that included all pins. 
+See MATRIX_TESTING_KEYMAP if you need it. Then set up a keymap that has all printable symbols
+in the first 4 rows. test each key & record output. Then switch the printable symbols to the
+bottom 4 rows & repeat. This was enough to show the matrix. 
+
+
+The full original keymap for the sculpt is 
+        A       B       C       D       E       F       G       H   --->  
+0       b       n       m       ,       .       /                
+1       g       h       "                                          
+2       7       8       9       0       Del             PgUp     
+3       p       [       ]       \                                
+4       y       u       i       o                                      
+5       ~       -       +=      j       k       l       ;       5
+6       a       s       d       q       w       e,      Up      left    
+7       F7      F8      F9      F10     F11     F12             f
+    			
+----->  I       J       K       L       M       N       O       P       Q       R       
+0               Caps                                                            FN      
+1                       Vol+    mute    Rctl            vol-    pgdn    LCTL            
+2                               Rshift                          LShift                  
+3                       Ralt                            LAlt                    
+4                                               LGUI                                            
+5       6       bakspc  1       2       3       4       F4      F5      F6                      
+6       Down    right                           spc     F1      F2      F3      tab             
+7       r       t       z       x       c               v       enter   Esc                     
+
+This works with 18 cols + 8  rows on a Teensy++, or Arm based Teensy. 
+
+The Astar mini has all pins exposed , so you can do 18x8
+If you want a speaker, LEDs &etc, you'll need to free up a pin.  I recommend joining columns
+R and L to the same pin. 
+
+Building - add ASTAR=1 to the compile line or leave out for teensy2++
+
+