Merge branch 'master' of github.com:jackhumbert/qmk_firmware

# Conflicts:
#	keyboard/ergodox_ez/keymaps/zweihander-osx/keymap.c
#	keyboard/ergodox_ez/keymaps/zweihander-osx/zweihander-osx.hex

2 files changed, 134 insertions, 0 deletions

diff --git a/keyboards/clueboard2/Makefile b/keyboards/clueboard2/Makefile
new file mode 100644
index 0000000000..e9367a90d0
--- /dev/null
+++ b/keyboards/clueboard2/Makefile
@@ -0,0 +1,71 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no	# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes	# Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+RGBLIGHT_ENABLE ?= no   # Enable keyboard underlight functionality (+4870)
+BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality (+1150)
+MIDI_ENABLE ?= no 		# MIDI controls
+AUDIO_ENABLE ?= no
+UNICODE_ENABLE ?= no 		# Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
diff --git a/keyboards/clueboard2/clueboard2.c b/keyboards/clueboard2/clueboard2.c
new file mode 100644
index 0000000000..d78ffed9ba
--- /dev/null
+++ b/keyboards/clueboard2/clueboard2.c
@@ -0,0 +1,63 @@
+#include "clueboard2.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+	matrix_init_user();
+	led_init_ports();
+
+    // JTAG disable for PORT F. write JTD bit twice within four cycles.
+    MCUCR |= (1<<JTD);
+    MCUCR |= (1<<JTD);
+};
+
+void led_init_ports() {
+    // * Set our LED pins as output
+    DDRB |= (1<<4);
+}
+
+void led_set_kb(uint8_t usb_led) {
+    if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+        // Turn capslock on
+        PORTB |= (1<<4);
+    } else {
+        // Turn capslock off
+        PORTB &= ~(1<<4);
+    }
+}
+
+/* Clueboard 2.0 LED locations:
+ *
+ * Capslock: B4, pull high to turn on
+ * LCtrl: Shared with Capslock, DO NOT INSTALL LED'S IN BOTH
+ * Page Up: B7, pull high to turn on
+ * Escape: D6, pull high to turn on
+ * Arrows: D4, pull high to turn on
+ */
+
+void backlight_init_ports(void) {
+    print("init_backlight_pin()\n");
+    // Set our LED pins as output
+    DDRD |= (1<<6); // Esc
+    DDRB |= (1<<7); // Page Up
+    DDRD |= (1<<4); // Arrows
+
+    // Set our LED pins low
+    PORTD &= ~(1<<6); // Esc
+    PORTB &= ~(1<<7); // Page Up
+    PORTD &= ~(1<<4); // Arrows
+}
+
+void backlight_set(uint8_t level) {
+    if ( level == 0 ) {
+        // Turn off light
+        PORTD |= (1<<6); // Esc
+        PORTB |= (1<<7); // Page Up
+        PORTD |= (1<<4); // Arrows
+    } else {
+        // Turn on light
+        PORTD &= ~(1<<6); // Esc
+        PORTB &= ~(1<<7); // Page Up
+        PORTD &= ~(1<<4); // Arrows
+    }
+}