Renames keyboard folder to keyboards, adds couple of tmk's fixes (#432)

* fixes from tmk's repo

* rename keyboard to keyboards

1 files changed, 0 insertions, 71 deletions

diff --git a/keyboard/jd45/Makefile b/keyboard/jd45/Makefile
deleted file mode 100644
index 75d544f16a..0000000000
--- a/keyboard/jd45/Makefile
+++ /dev/null
@@ -1,71 +0,0 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes	# Console for debug(+400)
-COMMAND_ENABLE ?= yes    # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE ?= yes  # Breathing sleep LED during USB suspend
-# NKRO_ENABLE ?= yes		# USB Nkey Rollover - not yet supported in LUFA
-BACKLIGHT_ENABLE ?= yes  # Enable keyboard backlight functionality
-MIDI_ENABLE ?= YES 		# MIDI controls
-# UNICODE_ENABLE ?= YES 		# Unicode
-BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-ifndef QUANTUM_DIR
-	include ../../Makefile
-endif