Add support of Model F 122 terminal keyboard

- change initialize of keyboard in matrix_scan()
- keymap for 122 keys
- Mafilefie and config.h for LUFA and PS/2 USART

1 files changed, 113 insertions, 0 deletions

diff --git a/converter/terminal_usb/Makefile b/converter/terminal_usb/Makefile
new file mode 100644
index 0000000000..6154d86826
--- /dev/null
+++ b/converter/terminal_usb/Makefile
@@ -0,0 +1,113 @@
+# Target file name (without extension).
+TARGET = terminal_lufa
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC = 	keymap.c \
+	matrix.c \
+	led.c
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162       # Teensy 1.0
+MCU = atmega32u4       # Teensy 2.0
+#MCU = at90usb646       # Teensy++ 1.0
+#MCU = at90usb1286      # Teensy++ 2.0
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+#MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+#EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
+
+#
+# PS/2 protocol implementations
+# 	USART is recommended if it is available, others are for reference purpose.
+# 	INT implementation will drop simultaneous key strokes.
+#
+PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
+#PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT = yes	# uses primitive reference code
+
+ifdef PS2_USE_USART
+    SRC += protocol/ps2_usart.c
+    OPT_DEFS += -DPS2_USE_USART
+endif
+
+ifdef PS2_USE_INT
+    SRC += protocol/ps2.c
+    OPT_DEFS += -DPS2_USE_INT
+endif
+
+ifdef PS2_USE_BUSYWAIT
+    SRC += protocol/ps2.c
+    OPT_DEFS += -DPS2_USE_BUSYWAIT
+endif
+
+
+#---------------- Programming Options --------------------------
+PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk