Removal of old minivan44 folder.

13 files changed, 0 insertions, 564 deletions

diff --git a/keyboards/minivan44/Makefile b/keyboards/minivan44/Makefile
deleted file mode 100644
index 45ca127807..0000000000
--- a/keyboards/minivan44/Makefile
+++ /dev/null
@@ -1,75 +0,0 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
-CONSOLE_ENABLE ?= yes        # Console for debug(+400)
-COMMAND_ENABLE ?= yes        # Commands for debug and configuration
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE ?= yes           # USB Nkey Rollover
-BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
-MIDI_ENABLE ?= no            # MIDI controls
-UNICODE_ENABLE ?= no         # Unicode
-BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
-AUDIO_ENABLE ?= no           # Audio output on port C6
-
-ifndef QUANTUM_DIR
-	include ../../Makefile
-endif
-
-
diff --git a/keyboards/minivan44/config.h b/keyboards/minivan44/config.h
deleted file mode 100644
index 0ae93c0957..0000000000
--- a/keyboards/minivan44/config.h
+++ /dev/null
@@ -1,162 +0,0 @@
-/*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#include "config_common.h"
-
-/* USB Device descriptor parameter */
-#define VENDOR_ID       0xFEAE
-#define PRODUCT_ID      0x8844
-#define DEVICE_VER      0x0002
-#define MANUFACTURER    Evan Sailer
-#define PRODUCT         TheVan 44
-#define DESCRIPTION     keyboard firmware for TV44
-
-/* key matrix size */
-#define MATRIX_ROWS 4
-#define MATRIX_COLS 12
-
-/*
- * Keyboard Matrix Assignments
- *
- * Change this to how you wired your keyboard
- * COLS: AVR pins used for columns, left to right
- * ROWS: AVR pins used for rows, top to bottom
- * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
- *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
- *
-*/
-#define MATRIX_ROW_PINS { D7, B5, F7, D4 }
-#define MATRIX_COL_PINS { D2, D3, D5, D6, B4, B6, F6, F5, F4, F1, F0, B3 }
-#define UNUSED_PINS
-
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
- 
-// #define BACKLIGHT_PIN B7
-// #define BACKLIGHT_BREATHING
-// #define BACKLIGHT_LEVELS 3
-
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCING_DELAY 5
-
-/* define if matrix has ghost (lacks anti-ghosting diodes) */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-
-/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
-#define LOCKING_SUPPORT_ENABLE
-/* Locking resynchronize hack */
-#define LOCKING_RESYNC_ENABLE
-
-/*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
-//#define FORCE_NKRO
-
-/*
- * Magic Key Options
- *
- * Magic keys are hotkey commands that allow control over firmware functions of
- * the keyboard. They are best used in combination with the HID Listen program,
- * found here: https://www.pjrc.com/teensy/hid_listen.html
- *
- * The options below allow the magic key functionality to be changed. This is
- * useful if your keyboard/keypad is missing keys and you want magic key support.
- *
- */
-
-/* key combination for magic key command */
-#define IS_COMMAND() ( \
-    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
-)
-
-/* control how magic key switches layers */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
-
-/* override magic key keymap */
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
-//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
-//#define MAGIC_KEY_HELP1          H
-//#define MAGIC_KEY_HELP2          SLASH
-//#define MAGIC_KEY_DEBUG          D
-//#define MAGIC_KEY_DEBUG_MATRIX   X
-//#define MAGIC_KEY_DEBUG_KBD      K
-//#define MAGIC_KEY_DEBUG_MOUSE    M
-//#define MAGIC_KEY_VERSION        V
-//#define MAGIC_KEY_STATUS         S
-//#define MAGIC_KEY_CONSOLE        C
-//#define MAGIC_KEY_LAYER0_ALT1    ESC
-//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
-//#define MAGIC_KEY_LAYER0         0
-//#define MAGIC_KEY_LAYER1         1
-//#define MAGIC_KEY_LAYER2         2
-//#define MAGIC_KEY_LAYER3         3
-//#define MAGIC_KEY_LAYER4         4
-//#define MAGIC_KEY_LAYER5         5
-//#define MAGIC_KEY_LAYER6         6
-//#define MAGIC_KEY_LAYER7         7
-//#define MAGIC_KEY_LAYER8         8
-//#define MAGIC_KEY_LAYER9         9
-//#define MAGIC_KEY_BOOTLOADER     PAUSE
-//#define MAGIC_KEY_LOCK           CAPS
-//#define MAGIC_KEY_EEPROM         E
-//#define MAGIC_KEY_NKRO           N
-//#define MAGIC_KEY_SLEEP_LED      Z
-
-/*
- * Feature disable options
- *  These options are also useful to firmware size reduction.
- */
-
-/* disable debug print */
-//#define NO_DEBUG
-
-/* disable print */
-//#define NO_PRINT
-
-/* disable action features */
-//#define NO_ACTION_LAYER
-//#define NO_ACTION_TAPPING
-//#define NO_ACTION_ONESHOT
-//#define NO_ACTION_MACRO
-//#define NO_ACTION_FUNCTION
-
-#endif
diff --git a/keyboards/minivan44/keymaps/default/Makefile b/keyboards/minivan44/keymaps/default/Makefile
deleted file mode 100644
index f4671a9d11..0000000000
--- a/keyboards/minivan44/keymaps/default/Makefile
+++ /dev/null
@@ -1,21 +0,0 @@
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = no           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
-	include ../../../../Makefile
-endif
\ No newline at end of file
diff --git a/keyboards/minivan44/keymaps/default/config.h b/keyboards/minivan44/keymaps/default/config.h
deleted file mode 100644
index df06a26206..0000000000
--- a/keyboards/minivan44/keymaps/default/config.h
+++ /dev/null
@@ -1,8 +0,0 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
-
-#include "../../config.h"
-
-// place overrides here
-
-#endif
\ No newline at end of file
diff --git a/keyboards/minivan44/keymaps/default/keymap.c b/keyboards/minivan44/keymaps/default/keymap.c
deleted file mode 100644
index d559a4b1c7..0000000000
--- a/keyboards/minivan44/keymaps/default/keymap.c
+++ /dev/null
@@ -1,97 +0,0 @@
-#include "minivan44.h"
-#include "action_layer.h"
-#include "eeconfig.h"
-
-extern keymap_config_t keymap_config;
-
-// Each layer gets a name for readability, which is then used in the keymap matrix below.
-// The underscores don't mean anything - you can have a layer called STUFF or any other name.
-// Layer names don't all need to be of the same length, obviously, and you can also skip them
-// entirely and just use numbers.
-
-#define _QW 0
-#define _DV 1
-#define _CM 2
-#define _L1 3
-#define _L2 4
-#define _L3 5
-
-// Macro name shortcuts
-#define QWERTY M(_QW)
-#define DVORAK M(_DV)
-#define COLEMAK M(_CM)
-
-// Fillers to make layering more clear
-#define _______ KC_TRNS
-#define XXXXXXX KC_NO
-
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-  [_QW] = { /* Qwerty */
-    {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC },
-    {MO(_L1), KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, MO(_L1) },
-    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_F,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, MO(_L2) },
-    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) }
-  },
-  [_DV] = { /* Dvorak */
-    {KC_TAB,  KC_COMM, KC_DOT,  KC_SLSH, KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_BSPC },
-    {MO(_L1), KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    MO(_L1) },
-    {KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    MO(_L2) },
-    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) }
-  },
-  [_CM] = { /* Colemak */
-    {KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_BSPC },
-    {MO(_L1), KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    MO(_L1) },
-    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_K,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, MO(_L2) },
-    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) }
-  },
-  [_L1] = { /* LAYER 1 */
-    {KC_GRV,  KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL  },
-    {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_DOWN, KC_UP,   KC_LEFT, KC_RGHT, _______ },
-    {_______, KC_ESC,  _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT },
-    {_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ }
-  },
-  [_L2] = { /* LAYER 2 */
-    {_______, QWERTY,  DVORAK,  COLEMAK, _______, _______, _______, KC_7,    KC_8,    KC_9,    KC_0,    _______ },
-    {KC_ESC,  KC_PIPE, KC_DQUO, KC_UNDS, KC_PLUS, LSFT(KC_LBRC), LSFT(KC_RBRC), KC_4,    KC_5,    KC_6,    KC_VOLU, KC_ENT  },
-    {_______, _______, _______, _______, _______, _______, KC_0,    KC_1,    KC_2,    KC_3,    KC_VOLD, _______ },
-    {_______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ }
-  },
-  [_L3] = { /* LAYER 3 */
-    {_______, _______, _______, _______, _______, _______, _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   _______ },
-    {KC_ESC,  _______, _______, _______, _______, _______, _______, KC_F5,   KC_F6,   KC_F7,   KC_F8,   _______ },
-    {KC_LSFT, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______ },
-    {_______, KC_LSFT, KC_B,    KC_SPC,  XXXXXXX, XXXXXXX, XXXXXXX, KC_C,    _______, _______, XXXXXXX, _______ }
-  }
-};
-
-const uint16_t PROGMEM fn_actions[] = {
-
-};
-
-void persistant_default_layer_set(uint16_t default_layer) {
-  eeconfig_update_default_layer(default_layer);
-  default_layer_set(default_layer);
-}
-
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-      switch(id) {
-        case _DV:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_DV);
-          }
-          break;
-        case _QW:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_QW);
-          }
-          break;
-        case _CM:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_CM);
-          }
-          break;
-      }
-    return MACRO_NONE;
-};
diff --git a/keyboards/minivan44/keymaps/default/readme.md b/keyboards/minivan44/keymaps/default/readme.md
deleted file mode 100644
index 189a9c0ff8..0000000000
--- a/keyboards/minivan44/keymaps/default/readme.md
+++ /dev/null
@@ -1 +0,0 @@
-# The default keymap for minivan44
\ No newline at end of file
diff --git a/keyboards/minivan44/keymaps/xyverz/Makefile b/keyboards/minivan44/keymaps/xyverz/Makefile
deleted file mode 100644
index f4671a9d11..0000000000
--- a/keyboards/minivan44/keymaps/xyverz/Makefile
+++ /dev/null
@@ -1,21 +0,0 @@
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = no         # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = no           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
-
-ifndef QUANTUM_DIR
-	include ../../../../Makefile
-endif
\ No newline at end of file
diff --git a/keyboards/minivan44/keymaps/xyverz/config.h b/keyboards/minivan44/keymaps/xyverz/config.h
deleted file mode 100644
index df06a26206..0000000000
--- a/keyboards/minivan44/keymaps/xyverz/config.h
+++ /dev/null
@@ -1,8 +0,0 @@
-#ifndef CONFIG_USER_H
-#define CONFIG_USER_H
-
-#include "../../config.h"
-
-// place overrides here
-
-#endif
\ No newline at end of file
diff --git a/keyboards/minivan44/keymaps/xyverz/keymap.c b/keyboards/minivan44/keymaps/xyverz/keymap.c
deleted file mode 100644
index f995da0e7e..0000000000
--- a/keyboards/minivan44/keymaps/xyverz/keymap.c
+++ /dev/null
@@ -1,92 +0,0 @@
-#include "minivan44.h"
-#include "action_layer.h"
-#include "eeconfig.h"
-
-extern keymap_config_t keymap_config;
-
-#define _DV 0
-#define _QW 1
-#define _CM 2
-#define _L1 3
-#define _L2 4
-
-// Macro name shortcuts
-#define DVORAK M(_DV)
-#define QWERTY M(_QW)
-#define COLEMAK M(_CM)
-
-// Fillers to make layering more clear
-#define _______ KC_TRNS
-#define XXXXXXX KC_NO
-
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-  [_DV] = { /* 0: Dvorak */
-    {KC_TAB,  KC_QUOT, KC_COMM, KC_DOT,  KC_P,    KC_Y,    KC_F,    KC_G,    KC_C,    KC_R,    KC_L,    KC_BSPC },
-    {MO(_L1), KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    KC_ENT  },
-    {KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    KC_RSFT },
-    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
-  },
-
-  [_QW] = { /* 1: Qwerty */
-    {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC },
-    {MO(_L1), KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_ENT  },
-    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT },
-    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
-  },
-
-  [_CM] = { /* 2: Colemak */
-    {KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_BSPC },
-    {MO(_L1), KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    KC_ENT  },
-    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_K,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT },
-    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
-  },
-
-  [_L1] = {/* 1: FN 1 */
-    {KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_DEL  },
-    {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_DOWN, KC_UP,   KC_LEFT, KC_RGHT, _______ },
-    {_______, _______, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT },
-    {_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, KC_SLSH, _______, _______ }
-  },
-
-  [_L2] = { /* 2: FN 2 */
-    {KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_ESC  },
-    {_______, KC_F11,  KC_F12,  _______, _______, _______, _______, _______, KC_HOME, KC_PGUP, KC_VOLU, KC_ENT  },
-    {_______, _______, _______, _______, _______, _______, _______, _______, KC_END,  KC_PGDN, KC_VOLD, _______ },
-    {QWERTY,  DVORAK,  COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______ }
-  }
-
-};
-
-const uint16_t PROGMEM fn_actions[] = {
-
-};
-
-void persistant_default_layer_set(uint16_t default_layer) {
-  eeconfig_update_default_layer(default_layer);
-  default_layer_set(default_layer);
-}
-
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-      switch(id) {
-        case _DV:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_DV);
-          }
-          break;
-        case _QW:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_QW);
-          }
-          break;
-        case _CM:
-          if (record->event.pressed) {
-            persistant_default_layer_set(1UL<<_CM);
-          }
-          break;
-      }
-    return MACRO_NONE;
-};
-
-
diff --git a/keyboards/minivan44/keymaps/xyverz/readme.md b/keyboards/minivan44/keymaps/xyverz/readme.md
deleted file mode 100644
index 189a9c0ff8..0000000000
--- a/keyboards/minivan44/keymaps/xyverz/readme.md
+++ /dev/null
@@ -1 +0,0 @@
-# The default keymap for minivan44
\ No newline at end of file
diff --git a/keyboards/minivan44/minivan44.c b/keyboards/minivan44/minivan44.c
deleted file mode 100644
index be8214fd5d..0000000000
--- a/keyboards/minivan44/minivan44.c
+++ /dev/null
@@ -1,28 +0,0 @@
-#include "minivan44.h"
-
-void matrix_init_kb(void) {
-	// put your keyboard start-up code here
-	// runs once when the firmware starts up
-
-	matrix_init_user();
-}
-
-void matrix_scan_kb(void) {
-	// put your looping keyboard code here
-	// runs every cycle (a lot)
-
-	matrix_scan_user();
-}
-
-bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
-	// put your per-action keyboard code here
-	// runs for every action, just before processing by the firmware
-
-	return process_record_user(keycode, record);
-}
-
-void led_set_kb(uint8_t usb_led) {
-	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
-
-	led_set_user(usb_led);
-}
diff --git a/keyboards/minivan44/minivan44.h b/keyboards/minivan44/minivan44.h
deleted file mode 100644
index c6119c2e16..0000000000
--- a/keyboards/minivan44/minivan44.h
+++ /dev/null
@@ -1,22 +0,0 @@
-#ifndef MINIVAN44_H
-#define MINIVAN44_H
-
-#include "quantum.h"
-
-// This a shortcut to help you visually see your layout.
-// The following is an example using the Planck MIT layout
-// The first section contains all of the arguements
-// The second converts the arguments into a two-dimensional array
-#define KEYMAP( \
-    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \
-    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \
-    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \
-    K30, K31, K32, K33,           K37, K38,      K39,      K3B  \
-) \
-{ \
-    { K00,   K01,   K02,   K03,  K04,   K05,   K06,   K07,   K08,   K09,   K0A,   K0B }, \
-    { K10,   K11,   K12,   K13,  K14,   K15,   K16,   K17,   K18,   K19,   K1A,   K1B }, \
-    { K20,   K21,   K22,   K23,  K24,   K25,   K26,   K27,   K28,   K29,   K2A,   K2B }, \
-    { K30,   K31,   K32,   K33,  KC_NO, KC_NO, KC_NO, K37,   K38,   K39,   K3A,   K3B }  \
-
-#endif
diff --git a/keyboards/minivan44/readme.md b/keyboards/minivan44/readme.md
deleted file mode 100644
index 59b62b0e66..0000000000
--- a/keyboards/minivan44/readme.md
+++ /dev/null
@@ -1,28 +0,0 @@
-minivan44 keyboard firmware
-======================
-
-## Quantum MK Firmware
-
-For the full Quantum feature list, see [the parent readme.md](/doc/readme.md).
-
-## Building
-
-Download or clone the whole firmware and navigate to the keyboards/minivan44 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. 
-
-Depending on which keymap you would like to use, you will have to compile slightly differently.
-
-### Default
-
-To build with the default keymap, simply run `make`.
-
-### Other Keymaps
-
-Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files.
-
-To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
-
-```
-$ make keymap=[default|jack|<name>]
-```
-
-Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
\ No newline at end of file