diff options
Diffstat (limited to 'things/cura.ini')
| -rw-r--r-- | things/cura.ini | 258 |
1 files changed, 0 insertions, 258 deletions
diff --git a/things/cura.ini b/things/cura.ini deleted file mode 100644 index f166cb9..0000000 --- a/things/cura.ini +++ /dev/null @@ -1,258 +0,0 @@ -[profile] -layer_height = 0.2 -wall_thickness = 1.6 -retraction_enable = False -solid_layer_thickness = 0.6 -fill_density = 100 -print_speed = 40 -print_temperature = 215 -print_temperature2 = 0 -print_temperature3 = 0 -print_temperature4 = 0 -print_temperature5 = 0 -print_bed_temperature = 45 -support = Everywhere -platform_adhesion = None -support_dual_extrusion = Both -wipe_tower = False -wipe_tower_volume = 15 -ooze_shield = False -filament_diameter = 1.75 -filament_diameter2 = 0 -filament_diameter3 = 0 -filament_diameter4 = 0 -filament_diameter5 = 0 -filament_flow = 100.0 -nozzle_size = 0.4 -retraction_speed = 40.0 -retraction_amount = 4.5 -retraction_dual_amount = 16.5 -retraction_min_travel = 1.5 -retraction_combing = All -retraction_minimal_extrusion = 0.02 -retraction_hop = 0.0 -bottom_thickness = 0.3 -layer0_width_factor = 100 -object_sink = 0.0 -overlap_dual = 0.15 -travel_speed = 100 -bottom_layer_speed = 20 -infill_speed = 0.0 -solidarea_speed = 0.0 -inset0_speed = 0.0 -insetx_speed = 0.0 -cool_min_layer_time = 5 -fan_enabled = True -skirt_line_count = 1 -skirt_gap = 3.0 -skirt_minimal_length = 150.0 -fan_full_height = 0.5 -fan_speed = 100 -fan_speed_max = 100 -cool_min_feedrate = 10 -cool_head_lift = False -solid_top = True -solid_bottom = True -fill_overlap = 15 -perimeter_before_infill = False -support_type = Grid -support_angle = 60 -support_fill_rate = 15 -support_xy_distance = 0.7 -support_z_distance = 0.15 -spiralize = False -simple_mode = False -brim_line_count = 20 -raft_margin = 5.0 -raft_line_spacing = 3.0 -raft_base_thickness = 0.3 -raft_base_linewidth = 1.0 -raft_interface_thickness = 0.27 -raft_interface_linewidth = 0.4 -raft_airgap_all = 0.0 -raft_airgap = 0.22 -raft_surface_layers = 2 -raft_surface_thickness = 0.27 -raft_surface_linewidth = 0.4 -fix_horrible_union_all_type_a = True -fix_horrible_union_all_type_b = False -fix_horrible_use_open_bits = False -fix_horrible_extensive_stitching = False -plugin_config = -object_center_x = -1 -object_center_y = -1 - -[alterations] -start.gcode = ;Sliced at: {day} {date} {time} - ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} - ;Print time: {print_time} - ;Filament used: {filament_amount}m {filament_weight}g - ;Filament cost: {filament_cost} - ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line - ;M109 S{print_temperature} ;Uncomment to add your own temperature line - G21 ;metric values - G90 ;absolute positioning - M82 ;set extruder to absolute mode - M107 ;start with the fan off - G28 X0 Y0 ;move X/Y to min endstops - G28 Z0 ;move Z to min endstops - G1 Z15.0 F{travel_speed} ;move the platform down 15mm - G92 E0 ;zero the extruded length - G1 F200 E3 ;extrude 3mm of feed stock - G92 E0 ;zero the extruded length again - G1 F{travel_speed} - ;Put printing message on LCD screen - M117 Printing... -end.gcode = ;End GCode - M104 S0 ;extruder heater off - M140 S0 ;heated bed heater off (if you have it) - G91 ;relative positioning - G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure - G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more - G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way - M84 ;steppers off - G90 ;absolute positioning - ;{profile_string} -start2.gcode = ;Sliced at: {day} {date} {time} - ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} - ;Print time: {print_time} - ;Filament used: {filament_amount}m {filament_weight}g - ;Filament cost: {filament_cost} - ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line - ;M104 S{print_temperature} ;Uncomment to add your own temperature line - ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line - ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line - G21 ;metric values - G90 ;absolute positioning - M107 ;start with the fan off - G28 X0 Y0 ;move X/Y to min endstops - G28 Z0 ;move Z to min endstops - G1 Z15.0 F{travel_speed} ;move the platform down 15mm - T1 ;Switch to the 2nd extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F200 E-{retraction_dual_amount} - T0 ;Switch to the first extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F{travel_speed} - ;Put printing message on LCD screen - M117 Printing... -end2.gcode = ;End GCode - M104 T0 S0 ;extruder heater off - M104 T1 S0 ;extruder heater off - M140 S0 ;heated bed heater off (if you have it) - G91 ;relative positioning - G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure - G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more - G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way - M84 ;steppers off - G90 ;absolute positioning - ;{profile_string} -start3.gcode = ;Sliced at: {day} {date} {time} - ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} - ;Print time: {print_time} - ;Filament used: {filament_amount}m {filament_weight}g - ;Filament cost: {filament_cost} - ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line - ;M104 S{print_temperature} ;Uncomment to add your own temperature line - ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line - ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line - G21 ;metric values - G90 ;absolute positioning - M107 ;start with the fan off - G28 X0 Y0 ;move X/Y to min endstops - G28 Z0 ;move Z to min endstops - G1 Z15.0 F{travel_speed} ;move the platform down 15mm - T2 ;Switch to the 3rd extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F200 E-{retraction_dual_amount} - T1 ;Switch to the 2nd extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F200 E-{retraction_dual_amount} - T0 ;Switch to the first extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F{travel_speed} - ;Put printing message on LCD screen - M117 Printing... -end3.gcode = ;End GCode - M104 T0 S0 ;extruder heater off - M104 T1 S0 ;extruder heater off - M104 T2 S0 ;extruder heater off - M140 S0 ;heated bed heater off (if you have it) - G91 ;relative positioning - G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure - G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more - G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way - M84 ;steppers off - G90 ;absolute positioning - ;{profile_string} -start4.gcode = ;Sliced at: {day} {date} {time} - ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} - ;Print time: {print_time} - ;Filament used: {filament_amount}m {filament_weight}g - ;Filament cost: {filament_cost} - ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line - ;M104 S{print_temperature} ;Uncomment to add your own temperature line - ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line - ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line - ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line - G21 ;metric values - G90 ;absolute positioning - M107 ;start with the fan off - G28 X0 Y0 ;move X/Y to min endstops - G28 Z0 ;move Z to min endstops - G1 Z15.0 F{travel_speed} ;move the platform down 15mm - T3 ;Switch to the 4th extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F200 E-{retraction_dual_amount} - T2 ;Switch to the 3rd extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F200 E-{retraction_dual_amount} - T1 ;Switch to the 2nd extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F200 E-{retraction_dual_amount} - T0 ;Switch to the first extruder - G92 E0 ;zero the extruded length - G1 F200 E10 ;extrude 10mm of feed stock - G92 E0 ;zero the extruded length again - G1 F{travel_speed} - ;Put printing message on LCD screen - M117 Printing... -end4.gcode = ;End GCode - M104 T0 S0 ;extruder heater off - M104 T1 S0 ;extruder heater off - M104 T2 S0 ;extruder heater off - M104 T3 S0 ;extruder heater off - M140 S0 ;heated bed heater off (if you have it) - G91 ;relative positioning - G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure - G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more - G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way - M84 ;steppers off - G90 ;absolute positioning - ;{profile_string} -support_start.gcode = -support_end.gcode = -cool_start.gcode = -cool_end.gcode = -replace.csv = -preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. - ;This code is added before the T(n) -postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. - ;This code is added after the T(n) - |