diff options
Diffstat (limited to 'things/cura.ini')
| -rw-r--r-- | things/cura.ini | 258 |
1 files changed, 258 insertions, 0 deletions
diff --git a/things/cura.ini b/things/cura.ini new file mode 100644 index 0000000..f166cb9 --- /dev/null +++ b/things/cura.ini @@ -0,0 +1,258 @@ +[profile] +layer_height = 0.2 +wall_thickness = 1.6 +retraction_enable = False +solid_layer_thickness = 0.6 +fill_density = 100 +print_speed = 40 +print_temperature = 215 +print_temperature2 = 0 +print_temperature3 = 0 +print_temperature4 = 0 +print_temperature5 = 0 +print_bed_temperature = 45 +support = Everywhere +platform_adhesion = None +support_dual_extrusion = Both +wipe_tower = False +wipe_tower_volume = 15 +ooze_shield = False +filament_diameter = 1.75 +filament_diameter2 = 0 +filament_diameter3 = 0 +filament_diameter4 = 0 +filament_diameter5 = 0 +filament_flow = 100.0 +nozzle_size = 0.4 +retraction_speed = 40.0 +retraction_amount = 4.5 +retraction_dual_amount = 16.5 +retraction_min_travel = 1.5 +retraction_combing = All +retraction_minimal_extrusion = 0.02 +retraction_hop = 0.0 +bottom_thickness = 0.3 +layer0_width_factor = 100 +object_sink = 0.0 +overlap_dual = 0.15 +travel_speed = 100 +bottom_layer_speed = 20 +infill_speed = 0.0 +solidarea_speed = 0.0 +inset0_speed = 0.0 +insetx_speed = 0.0 +cool_min_layer_time = 5 +fan_enabled = True +skirt_line_count = 1 +skirt_gap = 3.0 +skirt_minimal_length = 150.0 +fan_full_height = 0.5 +fan_speed = 100 +fan_speed_max = 100 +cool_min_feedrate = 10 +cool_head_lift = False +solid_top = True +solid_bottom = True +fill_overlap = 15 +perimeter_before_infill = False +support_type = Grid +support_angle = 60 +support_fill_rate = 15 +support_xy_distance = 0.7 +support_z_distance = 0.15 +spiralize = False +simple_mode = False +brim_line_count = 20 +raft_margin = 5.0 +raft_line_spacing = 3.0 +raft_base_thickness = 0.3 +raft_base_linewidth = 1.0 +raft_interface_thickness = 0.27 +raft_interface_linewidth = 0.4 +raft_airgap_all = 0.0 +raft_airgap = 0.22 +raft_surface_layers = 2 +raft_surface_thickness = 0.27 +raft_surface_linewidth = 0.4 +fix_horrible_union_all_type_a = True +fix_horrible_union_all_type_b = False +fix_horrible_use_open_bits = False +fix_horrible_extensive_stitching = False +plugin_config = +object_center_x = -1 +object_center_y = -1 + +[alterations] +start.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M109 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M82 ;set extruder to absolute mode + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed} ;move the platform down 15mm + G92 E0 ;zero the extruded length + G1 F200 E3 ;extrude 3mm of feed stock + G92 E0 ;zero the extruded length again + G1 F{travel_speed} + ;Put printing message on LCD screen + M117 Printing... +end.gcode = ;End GCode + M104 S0 ;extruder heater off + M140 S0 ;heated bed heater off (if you have it) + G91 ;relative positioning + G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more + G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way + M84 ;steppers off + G90 ;absolute positioning + ;{profile_string} +start2.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M104 S{print_temperature} ;Uncomment to add your own temperature line + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed} ;move the platform down 15mm + T1 ;Switch to the 2nd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T0 ;Switch to the first extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F{travel_speed} + ;Put printing message on LCD screen + M117 Printing... +end2.gcode = ;End GCode + M104 T0 S0 ;extruder heater off + M104 T1 S0 ;extruder heater off + M140 S0 ;heated bed heater off (if you have it) + G91 ;relative positioning + G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more + G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way + M84 ;steppers off + G90 ;absolute positioning + ;{profile_string} +start3.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M104 S{print_temperature} ;Uncomment to add your own temperature line + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed} ;move the platform down 15mm + T2 ;Switch to the 3rd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T1 ;Switch to the 2nd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T0 ;Switch to the first extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F{travel_speed} + ;Put printing message on LCD screen + M117 Printing... +end3.gcode = ;End GCode + M104 T0 S0 ;extruder heater off + M104 T1 S0 ;extruder heater off + M104 T2 S0 ;extruder heater off + M140 S0 ;heated bed heater off (if you have it) + G91 ;relative positioning + G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more + G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way + M84 ;steppers off + G90 ;absolute positioning + ;{profile_string} +start4.gcode = ;Sliced at: {day} {date} {time} + ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} + ;Print time: {print_time} + ;Filament used: {filament_amount}m {filament_weight}g + ;Filament cost: {filament_cost} + ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line + ;M104 S{print_temperature} ;Uncomment to add your own temperature line + ;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line + ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line + G21 ;metric values + G90 ;absolute positioning + M107 ;start with the fan off + G28 X0 Y0 ;move X/Y to min endstops + G28 Z0 ;move Z to min endstops + G1 Z15.0 F{travel_speed} ;move the platform down 15mm + T3 ;Switch to the 4th extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T2 ;Switch to the 3rd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T1 ;Switch to the 2nd extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F200 E-{retraction_dual_amount} + T0 ;Switch to the first extruder + G92 E0 ;zero the extruded length + G1 F200 E10 ;extrude 10mm of feed stock + G92 E0 ;zero the extruded length again + G1 F{travel_speed} + ;Put printing message on LCD screen + M117 Printing... +end4.gcode = ;End GCode + M104 T0 S0 ;extruder heater off + M104 T1 S0 ;extruder heater off + M104 T2 S0 ;extruder heater off + M104 T3 S0 ;extruder heater off + M140 S0 ;heated bed heater off (if you have it) + G91 ;relative positioning + G1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure + G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more + G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way + M84 ;steppers off + G90 ;absolute positioning + ;{profile_string} +support_start.gcode = +support_end.gcode = +cool_start.gcode = +cool_end.gcode = +replace.csv = +preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. + ;This code is added before the T(n) +postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. + ;This code is added after the T(n) + |