1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
|
/* mbed Microcontroller Library
*******************************************************************************
* Copyright (c) 2014, STMicroelectronics
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#include "mbed_assert.h"
#include "pinmap.h"
#include "PortNames.h"
#include "mbed_error.h"
// Enable GPIO clock and return GPIO base address
uint32_t Set_GPIO_Clock(uint32_t port_idx) {
uint32_t gpio_add;
switch (port_idx) {
case PortA:
gpio_add = GPIOA_BASE;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
break;
case PortB:
gpio_add = GPIOB_BASE;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
break;
case PortC:
gpio_add = GPIOC_BASE;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC, ENABLE);
break;
case PortD:
gpio_add = GPIOD_BASE;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOD, ENABLE);
break;
case PortE:
gpio_add = GPIOE_BASE;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOE, ENABLE);
break;
case PortF:
gpio_add = GPIOF_BASE;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOF, ENABLE);
break;
default:
gpio_add = 0;
error("Port number is not correct.");
break;
}
return gpio_add;
}
/**
* Configure pin (mode, speed, output type and pull-up/pull-down)
*/
void pin_function(PinName pin, int data) {
MBED_ASSERT(pin != (PinName)NC);
// Get the pin informations
uint32_t mode = STM_PIN_MODE(data);
uint32_t otype = STM_PIN_OTYPE(data);
uint32_t pupd = STM_PIN_PUPD(data);
uint32_t afnum = STM_PIN_AFNUM(data);
uint32_t port_index = STM_PORT(pin);
uint32_t pin_index = STM_PIN(pin);
// Enable GPIO clock
uint32_t gpio_add = Set_GPIO_Clock(port_index);
GPIO_TypeDef *gpio = (GPIO_TypeDef *)gpio_add;
// Configure Alternate Function
// Warning: Must be done before the GPIO is initialized
if (afnum != 0xFF) {
GPIO_PinAFConfig(gpio, (uint16_t)pin_index, afnum);
}
// Configure GPIO
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = (uint16_t)(1 << pin_index);
GPIO_InitStructure.GPIO_Mode = (GPIOMode_TypeDef)mode;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_Level_3;
GPIO_InitStructure.GPIO_OType = (GPIOOType_TypeDef)otype;
GPIO_InitStructure.GPIO_PuPd = (GPIOPuPd_TypeDef)pupd;
GPIO_Init(gpio, &GPIO_InitStructure);
// [TODO] Disconnect JTAG-DP + SW-DP signals.
// Warning: Need to reconnect under reset
//if ((pin == PA_13) || (pin == PA_14)) {
//
//}
//if ((pin == PA_15) || (pin == PB_3) || (pin == PB_4)) {
//
//}
}
/**
* Configure pin pull-up/pull-down
*/
void pin_mode(PinName pin, PinMode mode) {
MBED_ASSERT(pin != (PinName)NC);
uint32_t port_index = STM_PORT(pin);
uint32_t pin_index = STM_PIN(pin);
// Enable GPIO clock
uint32_t gpio_add = Set_GPIO_Clock(port_index);
GPIO_TypeDef *gpio = (GPIO_TypeDef *)gpio_add;
// Configure pull-up/pull-down resistors
uint32_t pupd = (uint32_t)mode;
if (pupd > 2)
pupd = 0; // Open-drain = No pull-up/No pull-down
gpio->PUPDR &= (uint32_t)(~(GPIO_PUPDR_PUPDR0 << (pin_index * 2)));
gpio->PUPDR |= (uint32_t)(pupd << (pin_index * 2));
}
|
