summaryrefslogtreecommitdiff
path: root/converter/ps2_usb/README.md
blob: 8a535949d8df77381d137fb70694de0b070cdbb3 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
PS/2 to USB keyboard converter
==============================
This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set 2.)


Connect Wires
-------------
In case of Teensy2.0(ATMega32U4):

1. Connect **Vcc** and **GND**.
2. Connect **Clock** and **Data** line. 
    - **Interrupt**:   **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible)
    - **Busywait**:    **Clock** is on `PD1` and **Data** on `PD0`.
    - **USART**:       **Clock** is on `PD5` and **Data** on `PD2`.
3. Optionally you need pull-up resistor. 1K-10K Ohm is OK.

To change pin configuration edit config.h.


Build Firmware
--------------
For **PJRC Teensy** just run `make`:

    $ make clean
    $ make

To select keymap:

    $ make clean
    $ make KEYMAP=[plain|jis|spacefn|...]

After that you will find HEX file `ps2_usb_lufa.hex` in current directory.


- For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`.

- For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`.


Keymap
------
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in README.md of top directory) and existent keymap files.


PS/2 signal handling implementations
------------------------------------
Following three methods can be used to implement PS/2 signal handling.

### Simple and stupid busy-wait(ps2_busywait.c)
    This is expected to implemented with portable C code for reference.
### Interrupt driven(ps2_interrupt.c)
    Uses pin interrupt to detect falling edge of clock line.
### USART hardware module(ps2_usart.c)
    Uses AVR USART engine to receive PS/2 signal.

To select method edit Makefile.


V-USB Support
-------------
With V-USB you can use this converter on ATmega(168/328) but it doesn't support NKRO at this time.

Circuit:

                    +---+   +---------------+
    USB            GND  |   |   ATmega168   |
    ===                 C3  |               |
    5V <-------+--------+---|Vcc,AVCC       |        PS/2
               R1           |               |        ====
    D- <----+--+-----R2-----|INT1        RXD|------->DATA
    D+ <----|---+----R3-----|INT0        XCK|------->CLOCK
            Z1  Z2          |               |      ->5V
    GND<----+---+--+--+-----|GND            |      ->GND
                   |  |     |               |
                   |  C2-+--|XTAL1          |
                   |     X1 |               |
                   +--C3-+--|XTAL2          |
                            +---------------+
    R1:     1.5K Ohm
    R2,R3:  68 Ohm
    Z1,Z2:  Zenner 3.6V
    C1,C2:  22pF
    C3:     0.1uF
    X1:     Crystal 20MHz(16MHz/12MHz)