From b624f32f944acdc59dcb130674c09090c5c404cb Mon Sep 17 00:00:00 2001 From: skullY Date: Fri, 30 Aug 2019 11:19:03 -0700 Subject: clang-format changes --- .../protocol/vusb/usbdrv/usbconfig-prototype.h | 86 +++++++++++----------- 1 file changed, 43 insertions(+), 43 deletions(-) (limited to 'tmk_core/protocol/vusb/usbdrv/usbconfig-prototype.h') diff --git a/tmk_core/protocol/vusb/usbdrv/usbconfig-prototype.h b/tmk_core/protocol/vusb/usbdrv/usbconfig-prototype.h index 847710e2a0..020ea51474 100644 --- a/tmk_core/protocol/vusb/usbdrv/usbconfig-prototype.h +++ b/tmk_core/protocol/vusb/usbdrv/usbconfig-prototype.h @@ -26,15 +26,15 @@ section at the end of this file). /* ---------------------------- Hardware Config ---------------------------- */ -#define USB_CFG_IOPORTNAME D +#define USB_CFG_IOPORTNAME D /* This is the port where the USB bus is connected. When you configure it to * "B", the registers PORTB, PINB and DDRB will be used. */ -#define USB_CFG_DMINUS_BIT 4 +#define USB_CFG_DMINUS_BIT 4 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. * This may be any bit in the port. */ -#define USB_CFG_DPLUS_BIT 2 +#define USB_CFG_DPLUS_BIT 2 /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. * This may be any bit in the port. Please note that D+ must also be connected * to interrupt pin INT0! [You can also use other interrupts, see section @@ -43,7 +43,7 @@ section at the end of this file). * interrupt, the USB interrupt will also be triggered at Start-Of-Frame * markers every millisecond.] */ -#define USB_CFG_CLOCK_KHZ (F_CPU/1000) +#define USB_CFG_CLOCK_KHZ (F_CPU / 1000) /* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code * require no crystal, they tolerate +/- 1% deviation from the nominal @@ -52,7 +52,7 @@ section at the end of this file). * Since F_CPU should be defined to your actual clock rate anyway, you should * not need to modify this setting. */ -#define USB_CFG_CHECK_CRC 0 +#define USB_CFG_CHECK_CRC 0 /* Define this to 1 if you want that the driver checks integrity of incoming * data packets (CRC checks). CRC checks cost quite a bit of code size and are * currently only available for 18 MHz crystal clock. You must choose @@ -75,18 +75,18 @@ section at the end of this file). /* --------------------------- Functional Range ---------------------------- */ -#define USB_CFG_HAVE_INTRIN_ENDPOINT 0 +#define USB_CFG_HAVE_INTRIN_ENDPOINT 0 /* Define this to 1 if you want to compile a version with two endpoints: The * default control endpoint 0 and an interrupt-in endpoint (any other endpoint * number). */ -#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0 +#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0 /* Define this to 1 if you want to compile a version with three endpoints: The * default control endpoint 0, an interrupt-in endpoint 3 (or the number * configured below) and a catch-all default interrupt-in endpoint as above. * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature. */ -#define USB_CFG_EP3_NUMBER 3 +#define USB_CFG_EP3_NUMBER 3 /* If the so-called endpoint 3 is used, it can now be configured to any other * endpoint number (except 0) with this macro. Default if undefined is 3. */ @@ -96,13 +96,13 @@ section at the end of this file). * Since the token is toggled BEFORE sending any data, the first packet is * sent with the oposite value of this configuration! */ -#define USB_CFG_IMPLEMENT_HALT 0 +#define USB_CFG_IMPLEMENT_HALT 0 /* Define this to 1 if you also want to implement the ENDPOINT_HALT feature * for endpoint 1 (interrupt endpoint). Although you may not need this feature, * it is required by the standard. We have made it a config option because it * bloats the code considerably. */ -#define USB_CFG_SUPPRESS_INTR_CODE 0 +#define USB_CFG_SUPPRESS_INTR_CODE 0 /* Define this to 1 if you want to declare interrupt-in endpoints, but don't * want to send any data over them. If this macro is defined to 1, functions * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if @@ -110,48 +110,48 @@ section at the end of this file). * (e.g. HID), but never want to send any data. This option saves a couple * of bytes in flash memory and the transmit buffers in RAM. */ -#define USB_CFG_INTR_POLL_INTERVAL 10 +#define USB_CFG_INTR_POLL_INTERVAL 10 /* If you compile a version with endpoint 1 (interrupt-in), this is the poll * interval. The value is in milliseconds and must not be less than 10 ms for * low speed devices. */ -#define USB_CFG_IS_SELF_POWERED 0 +#define USB_CFG_IS_SELF_POWERED 0 /* Define this to 1 if the device has its own power supply. Set it to 0 if the * device is powered from the USB bus. */ -#define USB_CFG_MAX_BUS_POWER 100 +#define USB_CFG_MAX_BUS_POWER 100 /* Set this variable to the maximum USB bus power consumption of your device. * The value is in milliamperes. [It will be divided by two since USB * communicates power requirements in units of 2 mA.] */ -#define USB_CFG_IMPLEMENT_FN_WRITE 0 +#define USB_CFG_IMPLEMENT_FN_WRITE 0 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out * transfers. Set it to 0 if you don't need it and want to save a couple of * bytes. */ -#define USB_CFG_IMPLEMENT_FN_READ 0 +#define USB_CFG_IMPLEMENT_FN_READ 0 /* Set this to 1 if you need to send control replies which are generated * "on the fly" when usbFunctionRead() is called. If you only want to send * data from a static buffer, set it to 0 and return the data from * usbFunctionSetup(). This saves a couple of bytes. */ -#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 +#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 /* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. * You must implement the function usbFunctionWriteOut() which receives all * interrupt/bulk data sent to any endpoint other than 0. The endpoint number * can be found in 'usbRxToken'. */ -#define USB_CFG_HAVE_FLOWCONTROL 0 +#define USB_CFG_HAVE_FLOWCONTROL 0 /* Define this to 1 if you want flowcontrol over USB data. See the definition * of the macros usbDisableAllRequests() and usbEnableAllRequests() in * usbdrv.h. */ -#define USB_CFG_DRIVER_FLASH_PAGE 0 +#define USB_CFG_DRIVER_FLASH_PAGE 0 /* If the device has more than 64 kBytes of flash, define this to the 64 k page * where the driver's constants (descriptors) are located. Or in other words: * Define this to 1 for boot loaders on the ATMega128. */ -#define USB_CFG_LONG_TRANSFERS 0 +#define USB_CFG_LONG_TRANSFERS 0 /* Define this to 1 if you want to send/receive blocks of more than 254 bytes * in a single control-in or control-out transfer. Note that the capability * for long transfers increases the driver size. @@ -172,7 +172,7 @@ section at the end of this file). /* This macro (if defined) is executed when a USB SET_ADDRESS request was * received. */ -#define USB_COUNT_SOF 0 +#define USB_COUNT_SOF 0 /* define this macro to 1 if you need the global variable "usbSofCount" which * counts SOF packets. This feature requires that the hardware interrupt is * connected to D- instead of D+. @@ -196,7 +196,7 @@ section at the end of this file). * Please note that Start Of Frame detection works only if D- is wired to the * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! */ -#define USB_CFG_CHECK_DATA_TOGGLING 0 +#define USB_CFG_CHECK_DATA_TOGGLING 0 /* define this macro to 1 if you want to filter out duplicate data packets * sent by the host. Duplicates occur only as a consequence of communication * errors, when the host does not receive an ACK. Please note that you need to @@ -204,11 +204,11 @@ section at the end of this file). * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable * for each control- and out-endpoint to check for duplicate packets. */ -#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 +#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 /* define this macro to 1 if you want the function usbMeasureFrameLength() * compiled in. This function can be used to calibrate the AVR's RC oscillator. */ -#define USB_USE_FAST_CRC 0 +#define USB_USE_FAST_CRC 0 /* The assembler module has two implementations for the CRC algorithm. One is * faster, the other is smaller. This CRC routine is only used for transmitted * messages where timing is not critical. The faster routine needs 31 cycles @@ -219,7 +219,7 @@ section at the end of this file). /* -------------------------- Device Description --------------------------- */ -#define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */ +#define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */ /* USB vendor ID for the device, low byte first. If you have registered your * own Vendor ID, define it here. Otherwise you may use one of obdev's free * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules! @@ -228,7 +228,7 @@ section at the end of this file). * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand * the implications! */ -#define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x05dc = 1500 */ +#define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x05dc = 1500 */ /* This is the ID of the product, low byte first. It is interpreted in the * scope of the vendor ID. If you have registered your own VID with usb.org * or if you have licensed a PID from somebody else, define it here. Otherwise @@ -239,10 +239,10 @@ section at the end of this file). * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand * the implications! */ -#define USB_CFG_DEVICE_VERSION 0x00, 0x01 +#define USB_CFG_DEVICE_VERSION 0x00, 0x01 /* Version number of the device: Minor number first, then major number. */ -#define USB_CFG_VENDOR_NAME 'o', 'b', 'd', 'e', 'v', '.', 'a', 't' +#define USB_CFG_VENDOR_NAME 'o', 'b', 'd', 'e', 'v', '.', 'a', 't' #define USB_CFG_VENDOR_NAME_LEN 8 /* These two values define the vendor name returned by the USB device. The name * must be given as a list of characters under single quotes. The characters @@ -252,7 +252,7 @@ section at the end of this file). * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for * details. */ -#define USB_CFG_DEVICE_NAME 'T', 'e', 'm', 'p', 'l', 'a', 't', 'e' +#define USB_CFG_DEVICE_NAME 'T', 'e', 'm', 'p', 'l', 'a', 't', 'e' #define USB_CFG_DEVICE_NAME_LEN 8 /* Same as above for the device name. If you don't want a device name, undefine * the macros. See the file USB-IDs-for-free.txt before you assign a name if @@ -267,14 +267,14 @@ section at the end of this file). * to fine tune control over USB descriptors such as the string descriptor * for the serial number. */ -#define USB_CFG_DEVICE_CLASS 0xff /* set to 0 if deferred to interface */ -#define USB_CFG_DEVICE_SUBCLASS 0 +#define USB_CFG_DEVICE_CLASS 0xff /* set to 0 if deferred to interface */ +#define USB_CFG_DEVICE_SUBCLASS 0 /* See USB specification if you want to conform to an existing device class. * Class 0xff is "vendor specific". */ -#define USB_CFG_INTERFACE_CLASS 0 /* define class here if not at device level */ -#define USB_CFG_INTERFACE_SUBCLASS 0 -#define USB_CFG_INTERFACE_PROTOCOL 0 +#define USB_CFG_INTERFACE_CLASS 0 /* define class here if not at device level */ +#define USB_CFG_INTERFACE_SUBCLASS 0 +#define USB_CFG_INTERFACE_PROTOCOL 0 /* See USB specification if you want to conform to an existing device class or * protocol. The following classes must be set at interface level: * HID class is 3, no subclass and protocol required (but may be useful!) @@ -345,16 +345,16 @@ section at the end of this file). * }; */ -#define USB_CFG_DESCR_PROPS_DEVICE 0 -#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 -#define USB_CFG_DESCR_PROPS_STRINGS 0 -#define USB_CFG_DESCR_PROPS_STRING_0 0 -#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 -#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 -#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 -#define USB_CFG_DESCR_PROPS_HID 0 -#define USB_CFG_DESCR_PROPS_HID_REPORT 0 -#define USB_CFG_DESCR_PROPS_UNKNOWN 0 +#define USB_CFG_DESCR_PROPS_DEVICE 0 +#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 +#define USB_CFG_DESCR_PROPS_STRINGS 0 +#define USB_CFG_DESCR_PROPS_STRING_0 0 +#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 +#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 +#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 +#define USB_CFG_DESCR_PROPS_HID 0 +#define USB_CFG_DESCR_PROPS_HID_REPORT 0 +#define USB_CFG_DESCR_PROPS_UNKNOWN 0 /* ----------------------- Optional MCU Description ------------------------ */ -- cgit v1.2.3