From 6901411bca0760ceb8acbe1f0c95feaed9d2aaeb Mon Sep 17 00:00:00 2001 From: Drashna Jaelre Date: Mon, 21 Jun 2021 13:00:11 -0700 Subject: Move optical sensor code to drivers folder (#13044) --- keyboards/ploopyco/pmw3360.h | 103 ------------------------------------------- 1 file changed, 103 deletions(-) delete mode 100644 keyboards/ploopyco/pmw3360.h (limited to 'keyboards/ploopyco/pmw3360.h') diff --git a/keyboards/ploopyco/pmw3360.h b/keyboards/ploopyco/pmw3360.h deleted file mode 100644 index c1d5e3badb..0000000000 --- a/keyboards/ploopyco/pmw3360.h +++ /dev/null @@ -1,103 +0,0 @@ -/* Copyright 2020 Christopher Courtney, aka Drashna Jael're (@drashna) - * Copyright 2019 Sunjun Kim - * Copyright 2020 Ploopy Corporation - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - */ - -#pragma once - -#include "spi_master.h" - -// Registers -#define REG_Product_ID 0x00 -#define REG_Revision_ID 0x01 -#define REG_Motion 0x02 -#define REG_Delta_X_L 0x03 -#define REG_Delta_X_H 0x04 -#define REG_Delta_Y_L 0x05 -#define REG_Delta_Y_H 0x06 -#define REG_SQUAL 0x07 -#define REG_Raw_Data_Sum 0x08 -#define REG_Maximum_Raw_data 0x09 -#define REG_Minimum_Raw_data 0x0A -#define REG_Shutter_Lower 0x0B -#define REG_Shutter_Upper 0x0C -#define REG_Control 0x0D -#define REG_Config1 0x0F -#define REG_Config2 0x10 -#define REG_Angle_Tune 0x11 -#define REG_Frame_Capture 0x12 -#define REG_SROM_Enable 0x13 -#define REG_Run_Downshift 0x14 -#define REG_Rest1_Rate_Lower 0x15 -#define REG_Rest1_Rate_Upper 0x16 -#define REG_Rest1_Downshift 0x17 -#define REG_Rest2_Rate_Lower 0x18 -#define REG_Rest2_Rate_Upper 0x19 -#define REG_Rest2_Downshift 0x1A -#define REG_Rest3_Rate_Lower 0x1B -#define REG_Rest3_Rate_Upper 0x1C -#define REG_Observation 0x24 -#define REG_Data_Out_Lower 0x25 -#define REG_Data_Out_Upper 0x26 -#define REG_Raw_Data_Dump 0x29 -#define REG_SROM_ID 0x2A -#define REG_Min_SQ_Run 0x2B -#define REG_Raw_Data_Threshold 0x2C -#define REG_Config5 0x2F -#define REG_Power_Up_Reset 0x3A -#define REG_Shutdown 0x3B -#define REG_Inverse_Product_ID 0x3F -#define REG_LiftCutoff_Tune3 0x41 -#define REG_Angle_Snap 0x42 -#define REG_LiftCutoff_Tune1 0x4A -#define REG_Motion_Burst 0x50 -#define REG_LiftCutoff_Tune_Timeout 0x58 -#define REG_LiftCutoff_Tune_Min_Length 0x5A -#define REG_SROM_Load_Burst 0x62 -#define REG_Lift_Config 0x63 -#define REG_Raw_Data_Burst 0x64 -#define REG_LiftCutoff_Tune2 0x65 - -#ifdef CONSOLE_ENABLE -void print_byte(uint8_t byte); -#endif - -typedef struct { - int8_t motion; - bool isMotion; // True if a motion is detected. - bool isOnSurface; // True when a chip is on a surface - int16_t dx; // displacement on x directions. Unit: Count. (CPI * Count = Inch value) - int8_t mdx; - int16_t dy; // displacement on y directions. - int8_t mdy; -} report_pmw_t; - - - -bool spi_start_adv(void); -void spi_stop_adv(void); -spi_status_t spi_write_adv(uint8_t reg_addr, uint8_t data); -uint8_t spi_read_adv(uint8_t reg_addr); -bool pmw_spi_init(void); -void pmw_set_cpi(uint16_t cpi); -void pmw_upload_firmware(void); -bool pmw_check_signature(void); -report_pmw_t pmw_read_burst(void); - - -#define degToRad(angleInDegrees) ((angleInDegrees)*M_PI / 180.0) -#define radToDeg(angleInRadians) ((angleInRadians)*180.0 / M_PI) -#define constrain(amt, low, high) ((amt) < (low) ? (low) : ((amt) > (high) ? (high) : (amt))) -- cgit v1.2.3