From d4ff836d6449b442e6f5ddc31678a489d0f6b3d6 Mon Sep 17 00:00:00 2001 From: vuhopkep Date: Thu, 27 Jun 2019 03:41:32 +0700 Subject: [Keyboard] Add Hnah40 keyboard (#6183) * Add Hnah40 keyboard Adding new keyboard Hnah40, open source hardware * update infor * make code looks neater * move to handwired board move and update readme file * update * update * update image * change bootloader type * last change --- keyboards/handwired/hnah40/rules.mk | 73 +++++++++++++++++++++++++++++++++++++ 1 file changed, 73 insertions(+) create mode 100644 keyboards/handwired/hnah40/rules.mk (limited to 'keyboards/handwired/hnah40/rules.mk') diff --git a/keyboards/handwired/hnah40/rules.mk b/keyboards/handwired/hnah40/rules.mk new file mode 100644 index 0000000000..efd11bfa5c --- /dev/null +++ b/keyboards/handwired/hnah40/rules.mk @@ -0,0 +1,73 @@ +# MCU name +MCU = atmega328p +PROTOCOL = VUSB + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +BOOTLOADER = bootloadHID + +# Flash program via avrdude, but default command is not suitable. +# You can use hnah40:default:program +PROGRAM_CMD = avrdude -c usbasp -p m328p -U flash:w:$(BUILD_DIR)/$(TARGET).hex + + +# disable debug code +OPT_DEFS = -DDEBUG_LEVEL=0 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches +HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) +NO_UART = yes +NO_SUSPEND_POWER_DOWN = yes \ No newline at end of file -- cgit v1.2.3