From 44441de8cad7255fd0637459ed39b89e34751b78 Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sun, 7 Aug 2016 17:04:39 +0300 Subject: Split keyboard makefiles into rules and Makefile --- keyboards/gh60/Makefile | 77 ++----------------------------------------------- keyboards/gh60/rules.mk | 68 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 71 insertions(+), 74 deletions(-) create mode 100644 keyboards/gh60/rules.mk (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile index 39a9cc0ae1..4e2a6f00fd 100644 --- a/keyboards/gh60/Makefile +++ b/keyboards/gh60/Makefile @@ -1,74 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -# CONSOLE_ENABLE ?= yes # Console for debug(+400) -# COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR - include ../../Makefile -endif - +ifndef MAKEFILE_INCLUDED + include ../../Makefile +endif \ No newline at end of file diff --git a/keyboards/gh60/rules.mk b/keyboards/gh60/rules.mk new file mode 100644 index 0000000000..73f4bd76e8 --- /dev/null +++ b/keyboards/gh60/rules.mk @@ -0,0 +1,68 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID -- cgit v1.2.3 From da226e61261e0c11e678d2086c00b2a45726083e Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sat, 20 Aug 2016 03:22:16 +0300 Subject: Update keyboard readme files with new makefile instructions --- keyboards/gh60/readme.md | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/readme.md b/keyboards/gh60/readme.md index 92302d507c..20afb0db07 100644 --- a/keyboards/gh60/readme.md +++ b/keyboards/gh60/readme.md @@ -48,13 +48,15 @@ Download or clone the whole firmware and navigate to the keyboards/gh60_rev_c fo Depending on which keymap you would like to use, you will have to compile slightly differently. ### Default -To build with the default keymap, simply run `make`. +To build with the default keymap, simply run `make default`. ### Other Keymaps Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. -To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: + ``` -$ make KEYMAP=[default|jack|] +$ make [default|jack|] ``` + Keymaps follow the format **__\.c__** and are stored in the `keymaps` folder. -- cgit v1.2.3 From 6cfdd077b5bcdcfe8b390e4c07965eaf6c081c76 Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Fri, 26 Aug 2016 00:05:58 +0300 Subject: Fix bad merge Led should have been added to KC60, not GH60 --- keyboards/gh60/rules.mk | 3 --- 1 file changed, 3 deletions(-) (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/rules.mk b/keyboards/gh60/rules.mk index b3c5c7271c..aba680e45b 100644 --- a/keyboards/gh60/rules.mk +++ b/keyboards/gh60/rules.mk @@ -1,6 +1,3 @@ -# project specific files -SRC = led.c - # MCU name #MCU = at90usb1287 MCU = atmega32u4 -- cgit v1.2.3 From a5b1af4999345239df5086351b52a5b4d2daa97e Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sat, 27 Aug 2016 18:40:50 +0300 Subject: Normalize line endings --- keyboards/gh60/Makefile | 148 +++++------ keyboards/gh60/config.h | 322 +++++++++++------------ keyboards/gh60/gh60.c | 50 ++-- keyboards/gh60/gh60.h | 148 +++++------ keyboards/gh60/keymaps/robotmaxtron/Makefile | 224 ++++++++-------- keyboards/gh60/keymaps/robotmaxtron/config.h | 380 +++++++++++++-------------- keyboards/gh60/pinout.txt | 34 +-- keyboards/gh60/readme.md | 120 ++++----- 8 files changed, 713 insertions(+), 713 deletions(-) (limited to 'keyboards/gh60') diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile index 39a9cc0ae1..075b77256f 100644 --- a/keyboards/gh60/Makefile +++ b/keyboards/gh60/Makefile @@ -1,74 +1,74 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -# CONSOLE_ENABLE ?= yes # Console for debug(+400) -# COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -# UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR - include ../../Makefile -endif - + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +# CONSOLE_ENABLE ?= yes # Console for debug(+400) +# COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +# UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID + + +ifndef QUANTUM_DIR + include ../../Makefile +endif + diff --git a/keyboards/gh60/config.h b/keyboards/gh60/config.h index 4813c4e786..97753bc069 100644 --- a/keyboards/gh60/config.h +++ b/keyboards/gh60/config.h @@ -1,161 +1,161 @@ -/* -Copyright 2012 Jun Wako - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see . -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define DEVICE_VER 0x0001 -#define MANUFACTURER geekhack -#define PRODUCT GH60 -#define DESCRIPTION t.m.k. keyboard firmware for GH60 - -/* key matrix size */ -#define MATRIX_ROWS 5 -#define MATRIX_COLS 14 - -/* - * Keyboard Matrix Assignments - * - * Change this to how you wired your keyboard - * COLS: AVR pins used for columns, left to right - * ROWS: AVR pins used for rows, top to bottom - * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) - * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) - * -*/ - #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } -// Rev A -// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 } -// Rev B/C - #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } -#define UNUSED_PINS - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 - -/* define if matrix has ghost (lacks anti-ghosting diodes) */ -//#define MATRIX_HAS_GHOST - -/* number of backlight levels */ -#define BACKLIGHT_LEVELS 3 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - -/* - * Force NKRO - * - * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved - * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the - * makefile for this to work.) - * - * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) - * until the next keyboard reset. - * - * NKRO may prevent your keystrokes from being detected in the BIOS, but it is - * fully operational during normal computer usage. - * - * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) - * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by - * bootmagic, NKRO mode will always be enabled until it is toggled again during a - * power-up. - * - */ -//#define FORCE_NKRO - -/* - * Magic Key Options - * - * Magic keys are hotkey commands that allow control over firmware functions of - * the keyboard. They are best used in combination with the HID Listen program, - * found here: https://www.pjrc.com/teensy/hid_listen.html - * - * The options below allow the magic key functionality to be changed. This is - * useful if your keyboard/keypad is missing keys and you want magic key support. - * - */ - -/* key combination for magic key command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ -) - -/* control how magic key switches layers */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false - -/* override magic key keymap */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM -//#define MAGIC_KEY_HELP1 H -//#define MAGIC_KEY_HELP2 SLASH -//#define MAGIC_KEY_DEBUG D -//#define MAGIC_KEY_DEBUG_MATRIX X -//#define MAGIC_KEY_DEBUG_KBD K -//#define MAGIC_KEY_DEBUG_MOUSE M -//#define MAGIC_KEY_VERSION V -//#define MAGIC_KEY_STATUS S -//#define MAGIC_KEY_CONSOLE C -//#define MAGIC_KEY_LAYER0_ALT1 ESC -//#define MAGIC_KEY_LAYER0_ALT2 GRAVE -//#define MAGIC_KEY_LAYER0 0 -//#define MAGIC_KEY_LAYER1 1 -//#define MAGIC_KEY_LAYER2 2 -//#define MAGIC_KEY_LAYER3 3 -//#define MAGIC_KEY_LAYER4 4 -//#define MAGIC_KEY_LAYER5 5 -//#define MAGIC_KEY_LAYER6 6 -//#define MAGIC_KEY_LAYER7 7 -//#define MAGIC_KEY_LAYER8 8 -//#define MAGIC_KEY_LAYER9 9 -//#define MAGIC_KEY_BOOTLOADER PAUSE -//#define MAGIC_KEY_LOCK CAPS -//#define MAGIC_KEY_EEPROM E -//#define MAGIC_KEY_NKRO N -//#define MAGIC_KEY_SLEEP_LED Z - -/* - * Feature disable options - * These options are also useful to firmware size reduction. - */ - -/* disable debug print */ -//#define NO_DEBUG - -/* disable print */ -//#define NO_PRINT - -/* disable action features */ -//#define NO_ACTION_LAYER -//#define NO_ACTION_TAPPING -//#define NO_ACTION_ONESHOT -//#define NO_ACTION_MACRO -//#define NO_ACTION_FUNCTION - -#endif +/* +Copyright 2012 Jun Wako + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT GH60 +#define DESCRIPTION t.m.k. keyboard firmware for GH60 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ + #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +// Rev A +// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 } +// Rev B/C + #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/gh60/gh60.c b/keyboards/gh60/gh60.c index 255d87de99..f5a158e12f 100644 --- a/keyboards/gh60/gh60.c +++ b/keyboards/gh60/gh60.c @@ -1,25 +1,25 @@ -#include "gh60.h" - -void led_set_kb(uint8_t usb_led) { - // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here - - if (usb_led & (1< - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see . -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define DEVICE_VER 0x0001 -#define MANUFACTURER geekhack -#define PRODUCT GH60 -#define DESCRIPTION t.m.k. keyboard firmware for GH60 - -/* key matrix size */ -#define MATRIX_ROWS 5 -#define MATRIX_COLS 14 - -/* - * Keyboard Matrix Assignments - * - * Change this to how you wired your keyboard - * COLS: AVR pins used for columns, left to right - * ROWS: AVR pins used for rows, top to bottom - * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) - * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) - * -*/ - #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } -// Rev A -// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 } -// Rev B/C - #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } -#define UNUSED_PINS - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 - -/* define if matrix has ghost (lacks anti-ghosting diodes) */ -//#define MATRIX_HAS_GHOST - -/* number of backlight levels */ -#define BACKLIGHT_LEVELS 3 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - -/* - * Force NKRO - * - * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved - * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the - * makefile for this to work.) - * - * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) - * until the next keyboard reset. - * - * NKRO may prevent your keystrokes from being detected in the BIOS, but it is - * fully operational during normal computer usage. - * - * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) - * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by - * bootmagic, NKRO mode will always be enabled until it is toggled again during a - * power-up. - * - */ -//#define FORCE_NKRO - -/* - * Magic Key Options - * - * Magic keys are hotkey commands that allow control over firmware functions of - * the keyboard. They are best used in combination with the HID Listen program, - * found here: https://www.pjrc.com/teensy/hid_listen.html - * - * The options below allow the magic key functionality to be changed. This is - * useful if your keyboard/keypad is missing keys and you want magic key support. - * - */ - -/* key combination for magic key command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ -) - -/* control how magic key switches layers */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false - -/* override magic key keymap */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM -//#define MAGIC_KEY_HELP1 H -//#define MAGIC_KEY_HELP2 SLASH -//#define MAGIC_KEY_DEBUG D -//#define MAGIC_KEY_DEBUG_MATRIX X -//#define MAGIC_KEY_DEBUG_KBD K -//#define MAGIC_KEY_DEBUG_MOUSE M -//#define MAGIC_KEY_VERSION V -//#define MAGIC_KEY_STATUS S -//#define MAGIC_KEY_CONSOLE C -//#define MAGIC_KEY_LAYER0_ALT1 ESC -//#define MAGIC_KEY_LAYER0_ALT2 GRAVE -//#define MAGIC_KEY_LAYER0 0 -//#define MAGIC_KEY_LAYER1 1 -//#define MAGIC_KEY_LAYER2 2 -//#define MAGIC_KEY_LAYER3 3 -//#define MAGIC_KEY_LAYER4 4 -//#define MAGIC_KEY_LAYER5 5 -//#define MAGIC_KEY_LAYER6 6 -//#define MAGIC_KEY_LAYER7 7 -//#define MAGIC_KEY_LAYER8 8 -//#define MAGIC_KEY_LAYER9 9 -//#define MAGIC_KEY_BOOTLOADER PAUSE -//#define MAGIC_KEY_LOCK CAPS -//#define MAGIC_KEY_EEPROM E -//#define MAGIC_KEY_NKRO N -//#define MAGIC_KEY_SLEEP_LED Z - -/* - * Feature disable options - * These options are also useful to firmware size reduction. - */ - -/* disable debug print */ -//#define NO_DEBUG - -/* disable print */ -//#define NO_PRINT - -/* disable action features */ -//#define NO_ACTION_LAYER -//#define NO_ACTION_TAPPING -//#define NO_ACTION_ONESHOT -//#define NO_ACTION_MACRO -//#define NO_ACTION_FUNCTION - -/* - * RGB Underglow - * These settings are for the F4 by default: - * - * - * #define ws2812_PORTREG PORTF - * #define ws2812_DDRREG DDRF - * #define ws2812_pin PF4 - * #define RGBLED_NUM 14 // Number of LEDs - * #define RGBLIGHT_HUE_STEP 10 - * #define RGBLIGHT_SAT_STEP 17 - * #define RGBLIGHT_VAL_STEP 17 - * - * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. - * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. - * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c -*/ - -/* Deprecated code below -#define ws2812_PORTREG PORTF -#define ws2812_DDRREG DDRF -#define ws2812_pin PF4 -*/ -#define RGB_DI_PIN F4 -#define RGBLIGHT_TIMER -#define RGBLED_NUM 8 // Number of LEDs -#define RGBLIGHT_HUE_STEP 8 -#define RGBLIGHT_SAT_STEP 8 -#define RGBLIGHT_VAL_STEP 8 -#endif +/* +Copyright 2012 Jun Wako + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT GH60 +#define DESCRIPTION t.m.k. keyboard firmware for GH60 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ + #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +// Rev A +// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 } +// Rev B/C + #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * RGB Underglow + * These settings are for the F4 by default: + * + * + * #define ws2812_PORTREG PORTF + * #define ws2812_DDRREG DDRF + * #define ws2812_pin PF4 + * #define RGBLED_NUM 14 // Number of LEDs + * #define RGBLIGHT_HUE_STEP 10 + * #define RGBLIGHT_SAT_STEP 17 + * #define RGBLIGHT_VAL_STEP 17 + * + * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. + * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. + * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c +*/ + +/* Deprecated code below +#define ws2812_PORTREG PORTF +#define ws2812_DDRREG DDRF +#define ws2812_pin PF4 +*/ +#define RGB_DI_PIN F4 +#define RGBLIGHT_TIMER +#define RGBLED_NUM 8 // Number of LEDs +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 +#endif diff --git a/keyboards/gh60/pinout.txt b/keyboards/gh60/pinout.txt index 3787f938e7..e9bf1983a5 100644 --- a/keyboards/gh60/pinout.txt +++ b/keyboards/gh60/pinout.txt @@ -1,18 +1,18 @@ - /* Column pin configuration - * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 - * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C) - */ - - /* Row pin configuration - * row: 0 1 2 3 4 - * pin: D0 D1 D2 D3 D5 - */ - - GPIO pads - 0 F7 WASD LEDs - 1 F6 ESC LED - 2 F5 FN LED - 3 F4 POKER Arrow LEDs - - B2 Capslock LED + /* Column pin configuration + * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 + * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C) + */ + + /* Row pin configuration + * row: 0 1 2 3 4 + * pin: D0 D1 D2 D3 D5 + */ + + GPIO pads + 0 F7 WASD LEDs + 1 F6 ESC LED + 2 F5 FN LED + 3 F4 POKER Arrow LEDs + + B2 Capslock LED B0 not connected \ No newline at end of file diff --git a/keyboards/gh60/readme.md b/keyboards/gh60/readme.md index 92302d507c..ad042483d8 100644 --- a/keyboards/gh60/readme.md +++ b/keyboards/gh60/readme.md @@ -1,60 +1,60 @@ -## gh60 Rev C keyboard firmware - -![gh60 Rev C PCB](gh60revc.jpg) - - /* Column pin configuration - * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 - * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C) - */ - - /* Row pin configuration - * row: 0 1 2 3 4 - * pin: D0 D1 D2 D3 D5 - */ - - GPIO pads - 0 F7 WASD LEDs - 1 F6 ESC LED - 2 F5 FN LED - 3 F4 POKER Arrow LEDs - - B2 Capslock LED - B0 not connected - -Functions to controls LED clusters - - gh60_caps_led_on() - gh60_poker_leds_on() - gh60_fn_led_on() - gh60_esc_led_on() - gh60_wasd_leds_on() - - gh60_caps_led_off() - gh60_poker_leds_off() - gh60_fn_led_off() - gh60_esc_led_off() - gh60_wasd_leds_off() - -====================== - -## Quantum MK Firmware - -For the full Quantum feature list, see [the parent readme.md](/readme.md). - -## Building - -Download or clone the whole firmware and navigate to the keyboards/gh60_rev_c folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. - -Depending on which keymap you would like to use, you will have to compile slightly differently. - -### Default -To build with the default keymap, simply run `make`. - -### Other Keymaps -Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. - -To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: -``` -$ make KEYMAP=[default|jack|] -``` -Keymaps follow the format **__\.c__** and are stored in the `keymaps` folder. +## gh60 Rev C keyboard firmware + +![gh60 Rev C PCB](gh60revc.jpg) + + /* Column pin configuration + * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 + * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C) + */ + + /* Row pin configuration + * row: 0 1 2 3 4 + * pin: D0 D1 D2 D3 D5 + */ + + GPIO pads + 0 F7 WASD LEDs + 1 F6 ESC LED + 2 F5 FN LED + 3 F4 POKER Arrow LEDs + + B2 Capslock LED + B0 not connected + +Functions to controls LED clusters + + gh60_caps_led_on() + gh60_poker_leds_on() + gh60_fn_led_on() + gh60_esc_led_on() + gh60_wasd_leds_on() + + gh60_caps_led_off() + gh60_poker_leds_off() + gh60_fn_led_off() + gh60_esc_led_off() + gh60_wasd_leds_off() + +====================== + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/gh60_rev_c folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|] +``` +Keymaps follow the format **__\.c__** and are stored in the `keymaps` folder. -- cgit v1.2.3