summaryrefslogtreecommitdiff
path: root/docs/serial_driver.md
AgeCommit message (Collapse)Author
2022-06-18[Core] Split ChibiOS usart split driver in protocol and hardware driver part ↵Stefan Kerkmann
(#16669)
2022-06-17[Core] Allow usage of ChibiOS's SIO driver for split keyboards (#15907)Stefan Kerkmann
2021-08-22Make solo half of split keyboards (more) usable. (#13523)Joakim Tufvegren
* Make solo half of split keyboards (more) usable. Using only one half of a split keyboard (that's using the split_common framework to communicate) is not a great experience, since several read timeouts per scan cycle cause an unusably slow scan rate. This change blocks all split communication attempts for 500 ms (configurable) after an error occurs, causing the scan rate to become at least _more_ usable, but might need some tweaking to work fully on most keyboards. One read timeout still needs to occur after the 500 ms has passed, and if that timeout isn't low enough, some scan cycles may still be too slow. * Fix lint complaint. * Require 25 consecutive comm errors to see comms as disconnected. The number of max errors can be overridden by defining `SPLIT_MAX_CONNECTION_ERRORS`. * Add comments to new defines, and ability to disable disconnection check. Also increase `SPLIT_MAX_CONNECTION_ERRORS` to 40, since it's divisible by most relevant numbers for the description. * Make lint happy ...again * Only update `connection_check_timer` when needed. * Add new defines to split keyboard documentation. * Move connection timeout logic to transport.c, add `is_transport_connected`. * Use split_common disconnection logic in matrix.c. Instead of doing more or less the same thing twice. * Move disconnection logic to `transport_master`. Is a cleaner implementation, and causes the scan rate while disconnected to increase instead of decrease. * Lint fixes. * Lower default `SERIAL_USART_TIMEOUT` to 20 ms. The read timeout must be low enough to not cause exessively long scan cycles when using a solo split half. 10 ms was determined from testing to work fine even with the slowest defined baudrate of 19200 (5 ms was too low for that case), so 20 ms should be fine for most cases. * Remove `SERIAL_USART_TIMEOUT` from ergodox_infinity/config.h Was somewhat mistakenly included in an earlier PR. * Fix building with `USE_I2C`. * Reduce built firmware size. Not really sure why this works, the idea was taken from tzarc's work on split disconnection. * Tweak and improve opt-out for split disconnection logic. There are now two ways to opt out from this feature: * Set `SPLIT_MAX_CONNECTION_ERRORS` to 0. This will completely disable the connection status checks (also affects the slave matrix reset logic in matrix.c, though). * Set `SPLIT_CONNECTION_CHECK_TIMEOUT` to 0. This will only disable the communication throttling while disconnected. Will make the firmware smaller. * Make split disconnection logic work with custom transports. Includes a fallback implementation for keyboards using a custom split_util.c but not a custom matrix.c (currently no such keyboard seems to be merged, though). * Remove unnecessary include of timer.h Co-authored-by: Joel Challis <git@zvecr.com> Co-authored-by: Joel Challis <git@zvecr.com>
2021-07-02[Core] Unite half-duplex and full-duplex serial drivers (#13081)Stefan Kerkmann
* Unite half-duplex and full-duplex serial driver. * Add full duplex operation mode to the interrupt based driver * Delete DMA UART based full duplex driver * The new driver targets #11930 * Fix freezes with failing transactions in half-duplex * Increase default serial TX/RX buffer size to 128 bytes * Correctly use bool instead of size_t Co-authored-by: Nick Brassel <nick@tzarc.org>
2021-05-26Add Full-duplex serial driver for ARM boards (#9842)Stefan Kerkmann
2020-11-30Configurable serial usart timeout (#11057)XScorpion2
2020-05-22Update ARM split keyboard docs (#9160)Joel Challis
* Update ARM split keyboard docs * Update docs/serial_driver.md Co-authored-by: Nick Brassel <nick@tzarc.org> Co-authored-by: Nick Brassel <nick@tzarc.org>
2020-05-21ARM split - Add uart half duplex transport support (#7987)Joel Challis
* ARM split - Add uart half duplex transport support * Fix for f103 * initial full duplex pass * partially remove full duplex * Correct speeds within driver docs Co-authored-by: Nick Brassel <nick@tzarc.org> Co-authored-by: Nick Brassel <nick@tzarc.org>