diff options
Diffstat (limited to 'tmk_core/tool/mbed/mbed-sdk/libraries/mbed/targets/cmsis/TARGET_STM/TARGET_STM32L0/stm32l0xx_hal_rcc.c')
| -rw-r--r-- | tmk_core/tool/mbed/mbed-sdk/libraries/mbed/targets/cmsis/TARGET_STM/TARGET_STM32L0/stm32l0xx_hal_rcc.c | 1370 |
1 files changed, 1370 insertions, 0 deletions
diff --git a/tmk_core/tool/mbed/mbed-sdk/libraries/mbed/targets/cmsis/TARGET_STM/TARGET_STM32L0/stm32l0xx_hal_rcc.c b/tmk_core/tool/mbed/mbed-sdk/libraries/mbed/targets/cmsis/TARGET_STM/TARGET_STM32L0/stm32l0xx_hal_rcc.c new file mode 100644 index 0000000000..f48f17eb5a --- /dev/null +++ b/tmk_core/tool/mbed/mbed-sdk/libraries/mbed/targets/cmsis/TARGET_STM/TARGET_STM32L0/stm32l0xx_hal_rcc.c @@ -0,0 +1,1370 @@ +/** + ****************************************************************************** + * @file stm32l0xx_hal_rcc.c + * @author MCD Application Team + * @version V1.2.0 + * @date 06-February-2015 + * @brief RCC HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Reset and Clock Control (RCC) peripheral: + * + Initialization and de-initialization functions + * + Peripheral Control functions + * + @verbatim + ============================================================================== + ##### RCC specific features ##### + ============================================================================== + [..] After reset the device is running from MSI (2 MHz) with Flash 0 WS, + all peripherals are off except internal SRAM, Flash and SW-DP. + (+) There is no prescaler on High speed (AHB) and Low speed (APB) busses; + all peripherals mapped on these busses are running at MSI speed. + (+) The clock for all peripherals is switched off, except the SRAM and + FLASH. + (+) All GPIOs are in input floating state, except the SW-DP pins which + are assigned to be used for debug purpose. + [..] Once the device started from reset, the user application has to: + (+) Configure the clock source to be used to drive the System clock + (if the application needs higher frequency/performance) + (+) Configure the System clock frequency and Flash settings + (+) Configure the AHB and APB busses prescalers + (+) Enable the clock for the peripheral(s) to be used + (+) Configure the clock source(s) for peripherals whose clocks are not + derived from the System clock (ADC, RTC/LCD, RNG and IWDG) + + ##### RCC Limitations ##### + ============================================================================== + [..] + A delay between an RCC peripheral clock enable and the effective peripheral + enabling should be taken into account in order to manage the peripheral read/write + from/to registeres. + (+) This delay depends on the peripheral mapping. + (+) If peripheral is mapped on AHB: the delay is 2 AHB clock cycle + after the clock enable bit is set on the hardware register + (+) If peripheral is mapped on APB: the delay is 2 APB clock cycle + after the clock enable bit is set on the hardware register + + [..] + Possible Workarounds: + (#) Enable the peripheral clock sometimes before the peripheral read/write + register is required. + (#) For AHB peripheral, insert two dummy read to the peripheral register. + (#) For APB peripheral, insert a dummy read to the peripheral register. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l0xx_hal.h" + +/** @addtogroup STM32L0xx_HAL_Driver + * @{ + */ + +/** @addtogroup RCC + * @brief RCC HAL module driver + * @{ + */ + +#ifdef HAL_RCC_MODULE_ENABLED + +/** @defgroup RCC_Private_Constants RCC Private constants + * @{ + */ +#define RCC_HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT +#define RCC_HSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */ +#define RCC_LSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */ +#define RCC_PLL_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */ +#define RCC_HSI48_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */ +#define RCC_MSI_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */ +#define RCC_CLOCKSWITCH_TIMEOUT_VALUE ((uint32_t)5000) /* 5 s */ + +#define __MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() +#define MCO1_GPIO_PORT GPIOA +#define MCO1_PIN GPIO_PIN_8 +#define MCO2_PIN GPIO_PIN_9 + +/** + * @} + */ + +/** @defgroup RCC_Private_Vatiables RCC Private Data + * @{ + */ +const uint8_t PLLMulTable[9] = {3, 4, 6, 8, 12, 16, 24, 32, 48}; +const uint8_t APBAHBPrescTable[16] = {0, 0, 0, 0, 1, 2, 3, 4, 1, 2, 3, 4, 6, 7, 8, 9}; + +/** + * @} + */ + +/** @addtogroup RCC_Exported_Functions + * @{ + */ + +/** @addtogroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + This section provide functions allowing to configure the internal/external + clocks, PLL, CSS and MCO. + [..] Internal/external clock and PLL configuration + (#) HSI (high-speed internal), 16 MHz factory-trimmed RC used directly + or through the PLL as System clock source. + (#) MSI (multi-speed internal), multispeed low power RC + (65.536 KHz to 4.194 MHz) MHz used as System clock source. + (#) LSI (low-speed internal), 37 KHz low consumption RC used as IWDG + and/or RTC clock source. + (#) HSE (high-speed external), 1 to 24 MHz crystal oscillator used + directly or through the PLL as System clock source. Can be used + also as RTC clock source. + (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source. + (#) PLL (clocked by HSI or HSE), for System clock and USB (48 MHz). + (#) CSS (Clock security system), once enable and if a HSE clock failure + occurs (HSE used directly or through PLL as System clock source), + the System clock is automatically switched to MSI and an interrupt + is generated if enabled. + The interrupt is linked to the Cortex-M3 NMI (Non-Maskable Interrupt) + exception vector. + (#) MCO (microcontroller clock output), used to output SYSCLK, HSI, MSI, + HSE, PLL, LSI or LSE clock (through a configurable prescaler) on + PA8 pin. + [..] System, AHB and APB busses clocks configuration + (#) Several clock sources can be used to drive the System clock (SYSCLK): MSI, HSI, + HSE and PLL. + The AHB clock (HCLK) is derived from System clock through configurable + prescaler and used to clock the CPU, memory and peripherals mapped + on IOPORT, AHB bus (DMA,Flash...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived + from AHB clock through configurable prescalers and used to clock + the peripherals mapped on these busses. You can use + "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks. + + -@- All the peripheral clocks are derived from the System clock (SYSCLK) except: + (+@) I2S: the I2S clock can be derived from an external clock mapped on the I2S_CKIN pin. + + (+@) RTC: the RTC clock can be derived either from the LSI, LSE or HSE clock + divided by 2 to 16. You have to use __HAL_RCC_RTC_CONFIG() and __HAL_RCC_RTC_ENABLE() + macros to configure this clock. + (+@) USB FS,and RNG require a frequency equal to 48 MHz to work correctly + This clock is derived from the main PLL or HSI48 RC oscillator. + (+@) IWDG clock which is always the LSI clock. + + (#) For the STM32L0xx devices, the maximum + frequency of the SYSCLK ,HCLK, APB1 and APB2 is 32 MHz. + Depending on the device voltage range, the maximum frequency should + be adapted accordingly: + ---------------------------------------------------------------- + | Wait states | HCLK clock frequency (MHz) | + | |------------------------------------------------| + | (Latency) | voltage range | voltage range | + | | 1.65 V - 3.6 V | 2.0 V - 3.6 V | + | |----------------|---------------|---------------| + | | VCORE = 1.2 V | VCORE = 1.5 V | VCORE = 1.8 V | + |-------------- |----------------|---------------|---------------| + |0WS(1CPU cycle)|0 < HCLK <= 2 |0 < HCLK <= 8 |0 < HCLK <= 16 | + |---------------|----------------|---------------|---------------| + |1WS(2CPU cycle)|2 < HCLK <= 4 |8 < HCLK <= 16 |16 < HCLK <= 32| + ---------------------------------------------------------------- +@endverbatim + * @{ + */ + +/** + * @brief Resets the RCC clock configuration to the default reset state. + * @note The default reset state of the clock configuration is given below: + * - MSI ON and used as system clock source (MSI range is not modified + * - by this function, it keep the value configured by user application) + * - HSI, HSE and PLL OFF + * - AHB, APB1 and APB2 prescaler set to 1. + * - CSS and MCO OFF + * - All interrupts disabled + * @note This function does not modify the configuration of the + * @note -Peripheral clocks + * @note -HSI48, LSI, LSE and RTC clocks + * @param None + * @retval None + */ +__weak void HAL_RCC_DeInit(void) +{ + /* This function is now defined in the file stm32L0xx_rcc_ex.c */ +} + +/** + * @brief Initializes the RCC Oscillators according to the specified parameters in the + * RCC_OscInitTypeDef. + * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC Oscillators. + * @note The PLL is not disabled when used as system clock. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + + uint32_t tickstart = 0; + + /* Check the parameters */ + assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); + /*------------------------------- HSE Configuration ------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) + { + /* Check the parameters */ + assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); + /* When the HSE is used as system clock or clock source for PLL in these cases HSE will not disabled */ + if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE) || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && ((RCC->CFGR & RCC_CFGR_PLLSRC) == RCC_CFGR_PLLSRC_HSE))) + { + if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) + { + return HAL_ERROR; + } + } + else + { + /* Reset HSEON and HSEBYP bits before configuring the HSE --------------*/ + __HAL_RCC_HSE_CONFIG(RCC_HSE_OFF); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Set the new HSE configuration ---------------------------------------*/ + __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); + + /* Check the HSE State */ + if((RCC_OscInitStruct->HSEState) != RCC_HSE_OFF) + { + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till HSE is disabled */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_HSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /*----------------------------- HSI Configuration --------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) + { + /* Check the parameters */ + assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); + assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); + + /* When the HSI is used as system clock it will not disabled */ + if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSI) || ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && ((RCC->CFGR & RCC_CFGR_PLLSRC) == RCC_CFGR_PLLSRC_HSI))) + { + /* When HSI is used as system clock it will not disabled */ + if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) + { + return HAL_ERROR; + } + /* Otherwise, just the calibration is allowed */ + else + { + /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + } + else + { + /* Check the HSI State */ + if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF) + { + /* Enable the Internal High Speed oscillator (HSI or HSIdiv4 */ + __HAL_RCC_HSI_CONFIG(RCC_OscInitStruct->HSIState); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till HSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ + __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); + } + else + { + /* Disable the Internal High Speed oscillator (HSI). */ + __HAL_RCC_HSI_CONFIG(RCC_OscInitStruct->HSIState); + + /* Get Start Tick*/ + tickstart = HAL_GetTick(); + + /* Wait till HSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_HSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /*----------------------------- MSI Configuration --------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_MSI) == RCC_OSCILLATORTYPE_MSI) + { + /* Check the parameters */ + assert_param(IS_RCC_MSI(RCC_OscInitStruct->MSIState)); + assert_param(IS_RCC_MSICALIBRATION_VALUE(RCC_OscInitStruct->MSICalibrationValue)); + + + /* When the MSI is used as system clock it will not disabled */ + if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_MSI) ) + { + if((__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) != RESET) && (RCC_OscInitStruct->MSIState != RCC_MSI_ON)) + { + return HAL_ERROR; + } + + /* Otherwise, just the calibration and MSI range change are allowed */ + else + { + /* Selects the Multiple Speed oscillator (MSI) clock range .*/ + __HAL_RCC_MSI_RANGE_CONFIG (RCC_OscInitStruct->MSIClockRange); + /* Adjusts the Multiple Speed oscillator (MSI) calibration value.*/ + __HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->MSICalibrationValue); + } + } + else + { + /* Check the MSI State */ + if((RCC_OscInitStruct->MSIState)!= RCC_MSI_OFF) + { + /* Enable the Internal High Speed oscillator (MSI). */ + __HAL_RCC_MSI_ENABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till MSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_MSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + /* Selects the Multiple Speed oscillator (MSI) clock range .*/ + __HAL_RCC_MSI_RANGE_CONFIG (RCC_OscInitStruct->MSIClockRange); + /* Adjusts the Multiple Speed oscillator (MSI) calibration value.*/ + __HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->MSICalibrationValue); + + } + else + { + /* Disable the Internal High Speed oscillator (MSI). */ + __HAL_RCC_MSI_DISABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till MSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_MSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /*------------------------------ LSI Configuration -------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) + { + /* Check the parameters */ + assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); + + /* Check the LSI State */ + if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF) + { + /* Enable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_ENABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till LSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Disable the Internal Low Speed oscillator (LSI). */ + __HAL_RCC_LSI_DISABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till LSI is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSI_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + +#if !defined (STM32L031xx) && !defined (STM32L041xx) && !defined(STM32L051xx) && !defined(STM32L061xx) && !defined(STM32L071xx) && !defined(STM32L081xx) + /*------------------------------ HSI48 Configuration -------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI48) == RCC_OSCILLATORTYPE_HSI48) + { + /* Check the parameters */ + assert_param(IS_RCC_HSI48(RCC_OscInitStruct->HSI48State)); + + /* Check the HSI48 State */ + if((RCC_OscInitStruct->HSI48State)!= RCC_HSI48_OFF) + { + /* Enable the Internal Low Speed oscillator (HSI48). */ + __HAL_RCC_HSI48_ENABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till HSI48 is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSI48RDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_HSI48_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Disable the Internal Low Speed oscillator (HSI48). */ + __HAL_RCC_HSI48_DISABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till HSI48 is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSI48RDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_HSI48_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } +#endif /* !(STM32L031xx) && !(STM32L041xx) && !defined(STM32L051xx) && !defined(STM32L061xx) && !defined(STM32L071xx) && !defined(STM32L081xx)*/ + + /*------------------------------ LSE Configuration -------------------------*/ + if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) + { + /* Check the parameters */ + assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); + + /* Enable Power Clock*/ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* Enable write access to Backup domain */ + PWR->CR |= PWR_CR_DBP; + + /* Wait for Backup domain Write protection disable */ + tickstart = HAL_GetTick(); + + while((PWR->CR & PWR_CR_DBP) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_DBP_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Reset LSEON and LSEBYP bits before configuring the LSE ----------------*/ + __HAL_RCC_LSE_CONFIG(RCC_LSE_OFF); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Set the new LSE configuration -----------------------------------------*/ + __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); + /* Check the LSE State */ + if((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF) + { + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till LSE is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + /*-------------------------------- PLL Configuration -----------------------*/ + /* Check the parameters */ + assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); + if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) + { + /* Check if the PLL is used as system clock or not */ + if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) + { + if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) + { + /* Check the parameters */ + assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); + assert_param(IS_RCC_PLL_MUL(RCC_OscInitStruct->PLL.PLLMUL)); + assert_param(IS_RCC_PLL_DIV(RCC_OscInitStruct->PLL.PLLDIV)); + + + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + + /* Configure the main PLL clock source, multiplication and division factors. */ + __HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, + RCC_OscInitStruct->PLL.PLLMUL, + RCC_OscInitStruct->PLL.PLLDIV); + /* Enable the main PLL. */ + __HAL_RCC_PLL_ENABLE(); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + /* Disable the main PLL. */ + __HAL_RCC_PLL_DISABLE(); + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait till PLL is ready */ + while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) + { + if((HAL_GetTick() - tickstart ) > RCC_PLL_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + else + { + return HAL_ERROR; + } + } + return HAL_OK; +} + +/** + * @brief Initializes the CPU, AHB and APB busses clocks according to the specified + * parameters in the RCC_ClkInitStruct. + * @param RCC_ClkInitStruct: pointer to an RCC_OscInitTypeDef structure that + * contains the configuration information for the RCC peripheral. + * @param FLatency: FLASH Latency, this parameter depends on System Clock Frequency + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated by HAL_RCC_GetHCLKFreq() function called within this function + * + * @note The MSI is used (enabled by hardware) as system clock source after + * startup from Reset, wake-up from STOP and STANDBY mode, or in case + * of failure of the HSE used directly or indirectly as system clock + * (if the Clock Security System CSS is enabled). + * + * @note A switch from one clock source to another occurs only if the target + * clock source is ready (clock stable after startup delay or PLL locked). + * If a clock source which is not yet ready is selected, the switch will + * occur when the clock source will be ready. + * @retval None + */ +HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency) +{ + + uint32_t tickstart = 0; + + /* Check the parameters */ + assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType)); + assert_param(IS_FLASH_LATENCY(FLatency)); + + /* To correctly read data from FLASH memory, the number of wait states (LATENCY) + must be correctly programmed according to the frequency of the CPU clock + (HCLK) and the supply voltage of the device. */ + + /* Increasing the CPU frequency */ + if(FLatency > (FLASH->ACR & FLASH_ACR_LATENCY)) + { + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) + { + return HAL_ERROR; + } + + /*-------------------------- HCLK Configuration --------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) + { + assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider); + } + + /*------------------------- SYSCLK Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) + { + assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource)); + + /* HSE is selected as System Clock Source */ + if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + /* Check the HSE ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + return HAL_ERROR; + } + } + + /* MSI is selected as System Clock Source */ + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_MSI) + { + /* Check the MSI ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == RESET) + { + return HAL_ERROR; + } + } + /* PLL is selected as System Clock Source */ + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) + { + /* Check the PLL ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + return HAL_ERROR; + } + } + /* HSI is selected as System Clock Source */ + else + { + /* Check the HSI ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + return HAL_ERROR; + } + } + MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_ClkInitStruct->SYSCLKSource); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_MSI) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_MSI) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + while(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + } + /* Decreasing the CPU frequency */ + else + { + /*-------------------------- HCLK Configuration --------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) + { + assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider); + } + + /*------------------------- SYSCLK Configuration -------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) + { + assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource)); + + /* HSE is selected as System Clock Source */ + if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + /* Check the HSE ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) + { + return HAL_ERROR; + } + } + + /* MSI is selected as System Clock Source */ + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_MSI) + { + /* Check the MSI ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_MSIRDY) == RESET) + { + return HAL_ERROR; + } + } + /* PLL is selected as System Clock Source */ + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) + { + /* Check the PLL ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) + { + return HAL_ERROR; + } + } + /* HSI is selected as System Clock Source */ + else + { + /* Check the HSI ready flag */ + if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) + { + return HAL_ERROR; + } + } + MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, RCC_ClkInitStruct->SYSCLKSource); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_MSI) + { + while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_MSI) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + else + { + while(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI) + { + if((HAL_GetTick() - tickstart ) > RCC_CLOCKSWITCH_TIMEOUT_VALUE) + { + return HAL_TIMEOUT; + } + } + } + } + + /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ + __HAL_FLASH_SET_LATENCY(FLatency); + + /* Check that the new number of wait states is taken into account to access the Flash + memory by reading the FLASH_ACR register */ + if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) + { + return HAL_ERROR; + } + } + + /*-------------------------- PCLK1 Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider); + } + + /*-------------------------- PCLK2 Configuration ---------------------------*/ + if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) + { + assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider)); + MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3)); + } + + /* Configure the source of time base considering new system clocks settings*/ + HAL_InitTick (TICK_INT_PRIORITY); + + return HAL_OK; +} + +/** + * @} + */ + +/** @addtogroup RCC_Exported_Functions_Group2 Peripheral Control functions + * @brief RCC clocks control functions + * +@verbatim + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the RCC Clocks + frequencies. + +@endverbatim + * @{ + */ + +/** + * @brief Selects the clock source to output on MCO pin. + * @note MCO pin should be configured in alternate function mode. + * @param RCC_MCOx: specifies the output direction for the clock source. + * For STM32L0xx family this parameter can have only one value: + * @arg RCC_MCO1: Clock source to output on MCO pin(PA8). + * @arg RCC_MCO2: Clock source to output on MCO pin(PA9). + * @param RCC_MCOSource: specifies the clock source to output. + * This parameter can be one of the following values: + * @arg RCC_MCO1SOURCE_NOCLOCK: No clock selected + * @arg RCC_MCO1SOURCE_SYSCLK: System clock selected + * @arg RCC_MCO1SOURCE_HSI: HSI oscillator clock selected + * @arg RCC_MCO1SOURCE_MSI: MSI oscillator clock selected + * @arg RCC_MCO1SOURCE_HSE: HSE oscillator clock selected + * @arg RCC_MCO1SOURCE_PLLCLK: PLL clock selected + * @arg RCC_MCO1SOURCE_LSI: LSI clock selected + * @arg RCC_MCO1SOURCE_LSE: LSE clock selected + * and in STM32L052xx,STM32L053xx,STM32L062xx, STM32L063xx + * STM32L072xx,STM32L073xx,STM32L082xx, STM32L083xx + * @arg RCC_MCO1SOURCE_HSI48: HSI48 clock selected + * @param RCC_MCODIV: specifies the MCO DIV. + * This parameter can be one of the following values: + * @arg RCC_MCODIV_1: no division applied to MCO clock + * @arg RCC_MCODIV_2: division by 2 applied to MCO clock + * @arg RCC_MCODIV_4: division by 4 applied to MCO clock + * @arg RCC_MCODIV_8: division by 8 applied to MCO clock + * @arg RCC_MCODIV_16: division by 16 applied to MCO clock + * @retval None + */ +void HAL_RCC_MCOConfig( uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv) +{ + GPIO_InitTypeDef GPIO_InitStruct; + /* Check the parameters */ + assert_param(IS_RCC_MCO(RCC_MCOx)); + assert_param(IS_RCC_MCODIV(RCC_MCODiv)); + assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource)); + + /* MCO Clock Enable */ + __MCO1_CLK_ENABLE(); + + /* Configure the MCO1 pin in alternate function mode */ + if(RCC_MCOx == RCC_MCO1) + { + GPIO_InitStruct.Pin = MCO1_PIN; + } + else + { + GPIO_InitStruct.Pin = MCO2_PIN; + } + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF0_MCO; + HAL_GPIO_Init(MCO1_GPIO_PORT, &GPIO_InitStruct); + + /* Mask MCO1 and MCO1PRE[2:0] bits then Select MCO1 clock source and prescaler */ + MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCOSEL | RCC_CFGR_MCO_PRE), ((RCC_MCOSource | RCC_MCODiv ))); +} + +/** + * @brief Enables the Clock Security System. + * @note If a failure is detected on the HSE oscillator clock, this oscillator + * is automatically disabled and an interrupt is generated to inform the + * software about the failure (Clock Security System Interrupt, CSSI), + * allowing the MCU to perform rescue operations. The CSSI is linked to + * the Cortex-M0+ NMI (Non-Maskable Interrupt) exception vector. + * @param None + * @retval None + */ +void HAL_RCC_EnableCSS(void) +{ + SET_BIT(RCC->CR, RCC_CR_CSSHSEON) ; +} + + +/** + * @brief Returns the SYSCLK frequency + * + * @note The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * @note If SYSCLK source is MSI, function returns values based on MSI + * Value as defined by the MSI range. + * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) + * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**) + * @note If SYSCLK source is PLL, function returns values based on HSE_VALUE(**) + * or HSI_VALUE(*) multiplied/divided by the PLL factors. + * @note (*) HSI_VALUE is a constant defined in stm32l0xx_hal_conf.h file (default value + * 16 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * @note (**) HSE_VALUE is a constant defined in stm32l0xx_hal_conf.h file (default value + * 8 MHz), user has to ensure that HSE_VALUE is same as the real + * frequency of the crystal used. Otherwise, this function may + * have wrong result. + * + * @note The result of this function could be not correct when using fractional + * value for HSE crystal. + * + * @note This function can be used by the user application to compute the + * baudrate for the communication peripherals or configure other parameters. + * + * @note Each time SYSCLK changes, this function must be called to update the + * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * + * @param None + * @retval SYSCLK frequency + */ +uint32_t HAL_RCC_GetSysClockFreq(void) +{ + uint32_t pllmul = 0, plldiv = 0, pllsource = 0, msirange = 0; + uint32_t sysclockfreq = 0; + + /* Get SYSCLK source -------------------------------------------------------*/ + + /*MSI frequency range in HZ*/ + msirange = (RCC->ICSCR & RCC_ICSCR_MSIRANGE) >> 13; + + switch (RCC->CFGR & RCC_CFGR_SWS) + { + case RCC_CFGR_SWS_MSI: /* MSI used as system clock */ + { + sysclockfreq = (32768 * (1 << (msirange + 1))); + break; + } + case RCC_SYSCLKSOURCE_STATUS_HSI: /* HSI used as system clock */ + { + if ((RCC->CR & RCC_CR_HSIDIVF) != 0) + { + sysclockfreq = (HSI_VALUE >> 2); + } + else + { + sysclockfreq = HSI_VALUE; + } + break; + } + case RCC_SYSCLKSOURCE_STATUS_HSE: /* HSE used as system clock */ + { + sysclockfreq = HSE_VALUE; + break; + } + case RCC_SYSCLKSOURCE_STATUS_PLLCLK: /* PLL used as system clock */ + { + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmul = RCC->CFGR & RCC_CFGR_PLLMUL; + plldiv = RCC->CFGR & RCC_CFGR_PLLDIV; + pllmul = PLLMulTable[(pllmul >> 18)]; + plldiv = (plldiv >> 22) + 1; + + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + + if (pllsource == RCC_CFGR_PLLSRC_HSI) + { + /* HSI oscillator clock selected as PLL clock source */ + if ((RCC->CR & RCC_CR_HSIDIVF) != 0) + { + sysclockfreq = (HSI_VALUE >> 2) * (pllmul / plldiv); + } + else + { + sysclockfreq =(((HSI_VALUE) * pllmul) / plldiv); + } + } + else + { + /* HSE selected as PLL clock source */ + sysclockfreq = (((HSE_VALUE) * pllmul) / plldiv); + } + break; + } + default: /* MSI used as system clock */ + { + sysclockfreq = (32768 * (1 << (msirange + 1))); + break; + } + } + return sysclockfreq; +} + +/** + * @brief Returns the HCLK frequency + * @note Each time HCLK changes, this function must be called to update the + * right HCLK value. Otherwise, any configuration based on this function will be incorrect. + * + * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency + * and updated within this function + * @param None + * @retval HCLK frequency + */ +uint32_t HAL_RCC_GetHCLKFreq(void) +{ + SystemCoreClock = HAL_RCC_GetSysClockFreq() >> APBAHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; + + return (SystemCoreClock); + +} + +/** + * @brief Returns the PCLK1 frequency + * @note Each time PCLK1 changes, this function must be called to update the + * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect. + * @param None + * @retval PCLK1 frequency + */ +uint32_t HAL_RCC_GetPCLK1Freq(void) +{ + + return ( HAL_RCC_GetHCLKFreq() >> APBAHBPrescTable[((RCC->CFGR & RCC_CFGR_PPRE1) >> 8)]); + +} + +/** + * @brief Returns the PCLK2 frequency + * @note Each time PCLK2 changes, this function must be called to update the + * right PCLK2 value. Otherwise, any configuration based on this function will be incorrect. + * @param None + * @retval PCLK2 frequency + */ +uint32_t HAL_RCC_GetPCLK2Freq(void) +{ + + return ( HAL_RCC_GetHCLKFreq() >> APBAHBPrescTable[((RCC->CFGR & RCC_CFGR_PPRE2) >> 11)]); + +} + +/** + * @brief Configures the RCC_OscInitStruct according to the internal + * RCC configuration registers. + * @param RCC_OscInitStruct: pointer to an RCC_OscInitTypeDef structure that + * will be configured. + * @retval None + */ +void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) +{ + /* Set all possible values for the Oscillator type parameter ---------------*/ + RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_MSI | RCC_OSCILLATORTYPE_HSI | \ + RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; +#if !defined (STM32L031xx) && !defined (STM32L041xx) && !defined (STM32L031xx) && !defined (STM32L041xx) && !defined(STM32L051xx) && !defined(STM32L061xx) && !defined(STM32L071xx) && !defined(STM32L081xx) + RCC_OscInitStruct->OscillatorType |= RCC_OSCILLATORTYPE_HSI48; +#endif + + /* Get the HSE configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP) + { + RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; + } + else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON) + { + RCC_OscInitStruct->HSEState = RCC_HSE_ON; + } + else + { + RCC_OscInitStruct->HSEState = RCC_HSE_OFF; + } + + /* Get the MSI configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_MSION) == RCC_CR_MSION) + { + RCC_OscInitStruct->MSIState = RCC_MSI_ON; + } + else + { + RCC_OscInitStruct->MSIState = RCC_MSI_OFF; + } + + RCC_OscInitStruct->MSICalibrationValue = (uint32_t)((RCC->CR &RCC_ICSCR_MSITRIM) >> 24); + RCC_OscInitStruct->MSIClockRange = (uint32_t)((RCC->ICSCR &RCC_ICSCR_MSIRANGE) >> 13); + +#if !defined (STM32L031xx) && !defined (STM32L041xx) && !defined(STM32L051xx) && !defined(STM32L061xx) && !defined(STM32L071xx) && !defined(STM32L081xx) + /* Get the HSI48 configuration -----------------------------------------------*/ + if((RCC->CRRCR &RCC_CRRCR_HSI48ON) == RCC_CRRCR_HSI48ON) + { + RCC_OscInitStruct->HSI48State = RCC_HSI48_ON; + } + else + { + RCC_OscInitStruct->HSI48State = RCC_HSI48_OFF; + } +#endif + + /* Get the HSI configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION) + { + RCC_OscInitStruct->HSIState = RCC_HSI_ON; + } + else + { + RCC_OscInitStruct->HSIState = RCC_HSI_OFF; + } + + RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->ICSCR &RCC_ICSCR_HSITRIM) >> 8); + + /* Get the LSE configuration -----------------------------------------------*/ + if((RCC->CSR &RCC_CSR_LSEBYP) == RCC_CSR_LSEBYP) + { + RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; + } + else if((RCC->CSR &RCC_CSR_LSEON) == RCC_CSR_LSEON) + { + RCC_OscInitStruct->LSEState = RCC_LSE_ON; + } + else + { + RCC_OscInitStruct->LSEState = RCC_LSE_OFF; + } + + /* Get the LSI configuration -----------------------------------------------*/ + if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION) + { + RCC_OscInitStruct->LSIState = RCC_LSI_ON; + } + else + { + RCC_OscInitStruct->LSIState = RCC_LSI_OFF; + } + + /* Get the PLL configuration -----------------------------------------------*/ + if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON) + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; + } + else + { + RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; + } + RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC); + RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMUL) >> 18; + RCC_OscInitStruct->PLL.PLLDIV = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLDIV) >> 22; + +} + +/** + * @brief Configures the RCC_ClkInitStruct according to the internal + * RCC configuration registers. + * @param RCC_OscInitStruct: pointer to an RCC_ClkInitTypeDef structure that + * will be configured. + * @param pFLatency: Pointer on the Flash Latency. + * @retval None + */ +void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency) +{ + /* Set all possible values for the Clock type parameter --------------------*/ + RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + + /* Get the SYSCLK configuration --------------------------------------------*/ + RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW); + + /* Get the HCLK configuration ----------------------------------------------*/ + RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE); + + /* Get the APB1 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1); + + /* Get the APB2 configuration ----------------------------------------------*/ + RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3); + + /* Get the Flash Wait State (Latency) configuration ------------------------*/ + *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY); +} + +/** + * @brief This function handles the RCC CSS interrupt request. + * @note This API should be called under the NMI_Handler(). + * @param None + * @retval None + */ +void HAL_RCC_NMI_IRQHandler(void) +{ + /* Check RCC CSSF flag */ + if(__HAL_RCC_GET_IT_SOURCE(RCC_IT_CSS)) + { + /* RCC Clock Security System interrupt user callback */ + HAL_RCC_CSSCallback(); + + /* Clear RCC CSS pending bit */ + __HAL_RCC_CLEAR_IT(RCC_IT_CSS); + } +} + +/** + * @brief RCC Clock Security System interrupt callback + * @param none + * @retval none + */ +__weak void HAL_RCC_CSSCallback(void) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_RCC_CSSCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_RCC_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ + |