diff options
Diffstat (limited to 'protocol/vusb/usbdrv/usbdrv.h')
| -rw-r--r-- | protocol/vusb/usbdrv/usbdrv.h | 735 |
1 files changed, 0 insertions, 735 deletions
diff --git a/protocol/vusb/usbdrv/usbdrv.h b/protocol/vusb/usbdrv/usbdrv.h deleted file mode 100644 index 42fe163720..0000000000 --- a/protocol/vusb/usbdrv/usbdrv.h +++ /dev/null @@ -1,735 +0,0 @@ -/* Name: usbdrv.h - * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers - * Author: Christian Starkjohann - * Creation Date: 2004-12-29 - * Tabsize: 4 - * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH - * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) - * This Revision: $Id: usbdrv.h 793 2010-07-15 15:58:11Z cs $ - */ - -#ifndef __usbdrv_h_included__ -#define __usbdrv_h_included__ -#include "usbconfig.h" -#include "usbportability.h" - -/* -Hardware Prerequisites: -======================= -USB lines D+ and D- MUST be wired to the same I/O port. We recommend that D+ -triggers the interrupt (best achieved by using INT0 for D+), but it is also -possible to trigger the interrupt from D-. If D- is used, interrupts are also -triggered by SOF packets. D- requires a pull-up of 1.5k to +3.5V (and the -device must be powered at 3.5V) to identify as low-speed USB device. A -pull-down or pull-up of 1M SHOULD be connected from D+ to +3.5V to prevent -interference when no USB master is connected. If you use Zener diodes to limit -the voltage on D+ and D-, you MUST use a pull-down resistor, not a pull-up. -We use D+ as interrupt source and not D- because it does not trigger on -keep-alive and RESET states. If you want to count keep-alive events with -USB_COUNT_SOF, you MUST use D- as an interrupt source. - -As a compile time option, the 1.5k pull-up resistor on D- can be made -switchable to allow the device to disconnect at will. See the definition of -usbDeviceConnect() and usbDeviceDisconnect() further down in this file. - -Please adapt the values in usbconfig.h according to your hardware! - -The device MUST be clocked at exactly 12 MHz, 15 MHz, 16 MHz or 20 MHz -or at 12.8 MHz resp. 16.5 MHz +/- 1%. See usbconfig-prototype.h for details. - - -Limitations: -============ -Robustness with respect to communication errors: -The driver assumes error-free communication. It DOES check for errors in -the PID, but does NOT check bit stuffing errors, SE0 in middle of a byte, -token CRC (5 bit) and data CRC (16 bit). CRC checks can not be performed due -to timing constraints: We must start sending a reply within 7 bit times. -Bit stuffing and misplaced SE0 would have to be checked in real-time, but CPU -performance does not permit that. The driver does not check Data0/Data1 -toggling, but application software can implement the check. - -Input characteristics: -Since no differential receiver circuit is used, electrical interference -robustness may suffer. The driver samples only one of the data lines with -an ordinary I/O pin's input characteristics. However, since this is only a -low speed USB implementation and the specification allows for 8 times the -bit rate over the same hardware, we should be on the safe side. Even the spec -requires detection of asymmetric states at high bit rate for SE0 detection. - -Number of endpoints: -The driver supports the following endpoints: - -- Endpoint 0, the default control endpoint. -- Any number of interrupt- or bulk-out endpoints. The data is sent to - usbFunctionWriteOut() and USB_CFG_IMPLEMENT_FN_WRITEOUT must be defined - to 1 to activate this feature. The endpoint number can be found in the - global variable 'usbRxToken'. -- One default interrupt- or bulk-in endpoint. This endpoint is used for - interrupt- or bulk-in transfers which are not handled by any other endpoint. - You must define USB_CFG_HAVE_INTRIN_ENDPOINT in order to activate this - feature and call usbSetInterrupt() to send interrupt/bulk data. -- One additional interrupt- or bulk-in endpoint. This was endpoint 3 in - previous versions of this driver but can now be configured to any endpoint - number. You must define USB_CFG_HAVE_INTRIN_ENDPOINT3 in order to activate - this feature and call usbSetInterrupt3() to send interrupt/bulk data. The - endpoint number can be set with USB_CFG_EP3_NUMBER. - -Please note that the USB standard forbids bulk endpoints for low speed devices! -Most operating systems allow them anyway, but the AVR will spend 90% of the CPU -time in the USB interrupt polling for bulk data. - -Maximum data payload: -Data payload of control in and out transfers may be up to 254 bytes. In order -to accept payload data of out transfers, you need to implement -'usbFunctionWrite()'. - -USB Suspend Mode supply current: -The USB standard limits power consumption to 500uA when the bus is in suspend -mode. This is not a problem for self-powered devices since they don't need -bus power anyway. Bus-powered devices can achieve this only by putting the -CPU in sleep mode. The driver does not implement suspend handling by itself. -However, the application may implement activity monitoring and wakeup from -sleep. The host sends regular SE0 states on the bus to keep it active. These -SE0 states can be detected by using D- as the interrupt source. Define -USB_COUNT_SOF to 1 and use the global variable usbSofCount to check for bus -activity. - -Operation without an USB master: -The driver behaves neutral without connection to an USB master if D- reads -as 1. To avoid spurious interrupts, we recommend a high impedance (e.g. 1M) -pull-down or pull-up resistor on D+ (interrupt). If Zener diodes are used, -use a pull-down. If D- becomes statically 0, the driver may block in the -interrupt routine. - -Interrupt latency: -The application must ensure that the USB interrupt is not disabled for more -than 25 cycles (this is for 12 MHz, faster clocks allow longer latency). -This implies that all interrupt routines must either have the "ISR_NOBLOCK" -attribute set (see "avr/interrupt.h") or be written in assembler with "sei" -as the first instruction. - -Maximum interrupt duration / CPU cycle consumption: -The driver handles all USB communication during the interrupt service -routine. The routine will not return before an entire USB message is received -and the reply is sent. This may be up to ca. 1200 cycles @ 12 MHz (= 100us) if -the host conforms to the standard. The driver will consume CPU cycles for all -USB messages, even if they address another (low-speed) device on the same bus. - -*/ - -/* ------------------------------------------------------------------------- */ -/* --------------------------- Module Interface ---------------------------- */ -/* ------------------------------------------------------------------------- */ - -#define USBDRV_VERSION 20100715 -/* This define uniquely identifies a driver version. It is a decimal number - * constructed from the driver's release date in the form YYYYMMDD. If the - * driver's behavior or interface changes, you can use this constant to - * distinguish versions. If it is not defined, the driver's release date is - * older than 2006-01-25. - */ - - -#ifndef USB_PUBLIC -#define USB_PUBLIC -#endif -/* USB_PUBLIC is used as declaration attribute for all functions exported by - * the USB driver. The default is no attribute (see above). You may define it - * to static either in usbconfig.h or from the command line if you include - * usbdrv.c instead of linking against it. Including the C module of the driver - * directly in your code saves a couple of bytes in flash memory. - */ - -#ifndef __ASSEMBLER__ -#ifndef uchar -#define uchar unsigned char -#endif -#ifndef schar -#define schar signed char -#endif -/* shortcuts for well defined 8 bit integer types */ - -#if USB_CFG_LONG_TRANSFERS /* if more than 254 bytes transfer size required */ -# define usbMsgLen_t unsigned -#else -# define usbMsgLen_t uchar -#endif -/* usbMsgLen_t is the data type used for transfer lengths. By default, it is - * defined to uchar, allowing a maximum of 254 bytes (255 is reserved for - * USB_NO_MSG below). If the usbconfig.h defines USB_CFG_LONG_TRANSFERS to 1, - * a 16 bit data type is used, allowing up to 16384 bytes (the rest is used - * for flags in the descriptor configuration). - */ -#define USB_NO_MSG ((usbMsgLen_t)-1) /* constant meaning "no message" */ - -struct usbRequest; /* forward declaration */ - -USB_PUBLIC void usbInit(void); -/* This function must be called before interrupts are enabled and the main - * loop is entered. We exepct that the PORT and DDR bits for D+ and D- have - * not been changed from their default status (which is 0). If you have changed - * them, set both back to 0 (configure them as input with no internal pull-up). - */ -USB_PUBLIC void usbPoll(void); -/* This function must be called at regular intervals from the main loop. - * Maximum delay between calls is somewhat less than 50ms (USB timeout for - * accepting a Setup message). Otherwise the device will not be recognized. - * Please note that debug outputs through the UART take ~ 0.5ms per byte - * at 19200 bps. - */ -extern uchar *usbMsgPtr; -/* This variable may be used to pass transmit data to the driver from the - * implementation of usbFunctionWrite(). It is also used internally by the - * driver for standard control requests. - */ -USB_PUBLIC usbMsgLen_t usbFunctionSetup(uchar data[8]); -/* This function is called when the driver receives a SETUP transaction from - * the host which is not answered by the driver itself (in practice: class and - * vendor requests). All control transfers start with a SETUP transaction where - * the host communicates the parameters of the following (optional) data - * transfer. The SETUP data is available in the 'data' parameter which can - * (and should) be casted to 'usbRequest_t *' for a more user-friendly access - * to parameters. - * - * If the SETUP indicates a control-in transfer, you should provide the - * requested data to the driver. There are two ways to transfer this data: - * (1) Set the global pointer 'usbMsgPtr' to the base of the static RAM data - * block and return the length of the data in 'usbFunctionSetup()'. The driver - * will handle the rest. Or (2) return USB_NO_MSG in 'usbFunctionSetup()'. The - * driver will then call 'usbFunctionRead()' when data is needed. See the - * documentation for usbFunctionRead() for details. - * - * If the SETUP indicates a control-out transfer, the only way to receive the - * data from the host is through the 'usbFunctionWrite()' call. If you - * implement this function, you must return USB_NO_MSG in 'usbFunctionSetup()' - * to indicate that 'usbFunctionWrite()' should be used. See the documentation - * of this function for more information. If you just want to ignore the data - * sent by the host, return 0 in 'usbFunctionSetup()'. - * - * Note that calls to the functions usbFunctionRead() and usbFunctionWrite() - * are only done if enabled by the configuration in usbconfig.h. - */ -USB_PUBLIC usbMsgLen_t usbFunctionDescriptor(struct usbRequest *rq); -/* You need to implement this function ONLY if you provide USB descriptors at - * runtime (which is an expert feature). It is very similar to - * usbFunctionSetup() above, but it is called only to request USB descriptor - * data. See the documentation of usbFunctionSetup() above for more info. - */ -#if USB_CFG_HAVE_INTRIN_ENDPOINT -USB_PUBLIC void usbSetInterrupt(uchar *data, uchar len); -/* This function sets the message which will be sent during the next interrupt - * IN transfer. The message is copied to an internal buffer and must not exceed - * a length of 8 bytes. The message may be 0 bytes long just to indicate the - * interrupt status to the host. - * If you need to transfer more bytes, use a control read after the interrupt. - */ -#define usbInterruptIsReady() (usbTxLen1 & 0x10) -/* This macro indicates whether the last interrupt message has already been - * sent. If you set a new interrupt message before the old was sent, the - * message already buffered will be lost. - */ -#if USB_CFG_HAVE_INTRIN_ENDPOINT3 -USB_PUBLIC void usbSetInterrupt3(uchar *data, uchar len); -#define usbInterruptIsReady3() (usbTxLen3 & 0x10) -/* Same as above for endpoint 3 */ -#endif -#endif /* USB_CFG_HAVE_INTRIN_ENDPOINT */ -#if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH /* simplified interface for backward compatibility */ -#define usbHidReportDescriptor usbDescriptorHidReport -/* should be declared as: PROGMEM char usbHidReportDescriptor[]; */ -/* If you implement an HID device, you need to provide a report descriptor. - * The HID report descriptor syntax is a bit complex. If you understand how - * report descriptors are constructed, we recommend that you use the HID - * Descriptor Tool from usb.org, see http://www.usb.org/developers/hidpage/. - * Otherwise you should probably start with a working example. - */ -#endif /* USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH */ -#if USB_CFG_IMPLEMENT_FN_WRITE -USB_PUBLIC uchar usbFunctionWrite(uchar *data, uchar len); -/* This function is called by the driver to provide a control transfer's - * payload data (control-out). It is called in chunks of up to 8 bytes. The - * total count provided in the current control transfer can be obtained from - * the 'length' property in the setup data. If an error occurred during - * processing, return 0xff (== -1). The driver will answer the entire transfer - * with a STALL token in this case. If you have received the entire payload - * successfully, return 1. If you expect more data, return 0. If you don't - * know whether the host will send more data (you should know, the total is - * provided in the usbFunctionSetup() call!), return 1. - * NOTE: If you return 0xff for STALL, 'usbFunctionWrite()' may still be called - * for the remaining data. You must continue to return 0xff for STALL in these - * calls. - * In order to get usbFunctionWrite() called, define USB_CFG_IMPLEMENT_FN_WRITE - * to 1 in usbconfig.h and return 0xff in usbFunctionSetup().. - */ -#endif /* USB_CFG_IMPLEMENT_FN_WRITE */ -#if USB_CFG_IMPLEMENT_FN_READ -USB_PUBLIC uchar usbFunctionRead(uchar *data, uchar len); -/* This function is called by the driver to ask the application for a control - * transfer's payload data (control-in). It is called in chunks of up to 8 - * bytes each. You should copy the data to the location given by 'data' and - * return the actual number of bytes copied. If you return less than requested, - * the control-in transfer is terminated. If you return 0xff, the driver aborts - * the transfer with a STALL token. - * In order to get usbFunctionRead() called, define USB_CFG_IMPLEMENT_FN_READ - * to 1 in usbconfig.h and return 0xff in usbFunctionSetup().. - */ -#endif /* USB_CFG_IMPLEMENT_FN_READ */ - -extern uchar usbRxToken; /* may be used in usbFunctionWriteOut() below */ -#if USB_CFG_IMPLEMENT_FN_WRITEOUT -USB_PUBLIC void usbFunctionWriteOut(uchar *data, uchar len); -/* This function is called by the driver when data is received on an interrupt- - * or bulk-out endpoint. The endpoint number can be found in the global - * variable usbRxToken. You must define USB_CFG_IMPLEMENT_FN_WRITEOUT to 1 in - * usbconfig.h to get this function called. - */ -#endif /* USB_CFG_IMPLEMENT_FN_WRITEOUT */ -#ifdef USB_CFG_PULLUP_IOPORTNAME -#define usbDeviceConnect() ((USB_PULLUP_DDR |= (1<<USB_CFG_PULLUP_BIT)), \ - (USB_PULLUP_OUT |= (1<<USB_CFG_PULLUP_BIT))) -#define usbDeviceDisconnect() ((USB_PULLUP_DDR &= ~(1<<USB_CFG_PULLUP_BIT)), \ - (USB_PULLUP_OUT &= ~(1<<USB_CFG_PULLUP_BIT))) -#else /* USB_CFG_PULLUP_IOPORTNAME */ -#define usbDeviceConnect() (USBDDR &= ~(1<<USBMINUS)) -#define usbDeviceDisconnect() (USBDDR |= (1<<USBMINUS)) -#endif /* USB_CFG_PULLUP_IOPORTNAME */ -/* The macros usbDeviceConnect() and usbDeviceDisconnect() (intended to look - * like a function) connect resp. disconnect the device from the host's USB. - * If the constants USB_CFG_PULLUP_IOPORT and USB_CFG_PULLUP_BIT are defined - * in usbconfig.h, a disconnect consists of removing the pull-up resisitor - * from D-, otherwise the disconnect is done by brute-force pulling D- to GND. - * This does not conform to the spec, but it works. - * Please note that the USB interrupt must be disabled while the device is - * in disconnected state, or the interrupt handler will hang! You can either - * turn off the USB interrupt selectively with - * USB_INTR_ENABLE &= ~(1 << USB_INTR_ENABLE_BIT) - * or use cli() to disable interrupts globally. - */ -extern unsigned usbCrc16(unsigned data, uchar len); -#define usbCrc16(data, len) usbCrc16((unsigned)(data), len) -/* This function calculates the binary complement of the data CRC used in - * USB data packets. The value is used to build raw transmit packets. - * You may want to use this function for data checksums or to verify received - * data. We enforce 16 bit calling conventions for compatibility with IAR's - * tiny memory model. - */ -extern unsigned usbCrc16Append(unsigned data, uchar len); -#define usbCrc16Append(data, len) usbCrc16Append((unsigned)(data), len) -/* This function is equivalent to usbCrc16() above, except that it appends - * the 2 bytes CRC (lowbyte first) in the 'data' buffer after reading 'len' - * bytes. - */ -#if USB_CFG_HAVE_MEASURE_FRAME_LENGTH -extern unsigned usbMeasureFrameLength(void); -/* This function MUST be called IMMEDIATELY AFTER USB reset and measures 1/7 of - * the number of CPU cycles during one USB frame minus one low speed bit - * length. In other words: return value = 1499 * (F_CPU / 10.5 MHz) - * Since this is a busy wait, you MUST disable all interrupts with cli() before - * calling this function. - * This can be used to calibrate the AVR's RC oscillator. - */ -#endif -extern uchar usbConfiguration; -/* This value contains the current configuration set by the host. The driver - * allows setting and querying of this variable with the USB SET_CONFIGURATION - * and GET_CONFIGURATION requests, but does not use it otherwise. - * You may want to reflect the "configured" status with a LED on the device or - * switch on high power parts of the circuit only if the device is configured. - */ -#if USB_COUNT_SOF -extern volatile uchar usbSofCount; -/* This variable is incremented on every SOF packet. It is only available if - * the macro USB_COUNT_SOF is defined to a value != 0. - */ -#endif -#if USB_CFG_CHECK_DATA_TOGGLING -extern uchar usbCurrentDataToken; -/* This variable can be checked in usbFunctionWrite() and usbFunctionWriteOut() - * to ignore duplicate packets. - */ -#endif - -#define USB_STRING_DESCRIPTOR_HEADER(stringLength) ((2*(stringLength)+2) | (3<<8)) -/* This macro builds a descriptor header for a string descriptor given the - * string's length. See usbdrv.c for an example how to use it. - */ -#if USB_CFG_HAVE_FLOWCONTROL -extern volatile schar usbRxLen; -#define usbDisableAllRequests() usbRxLen = -1 -/* Must be called from usbFunctionWrite(). This macro disables all data input - * from the USB interface. Requests from the host are answered with a NAK - * while they are disabled. - */ -#define usbEnableAllRequests() usbRxLen = 0 -/* May only be called if requests are disabled. This macro enables input from - * the USB interface after it has been disabled with usbDisableAllRequests(). - */ -#define usbAllRequestsAreDisabled() (usbRxLen < 0) -/* Use this macro to find out whether requests are disabled. It may be needed - * to ensure that usbEnableAllRequests() is never called when requests are - * enabled. - */ -#endif - -#define USB_SET_DATATOKEN1(token) usbTxBuf1[0] = token -#define USB_SET_DATATOKEN3(token) usbTxBuf3[0] = token -/* These two macros can be used by application software to reset data toggling - * for interrupt-in endpoints 1 and 3. Since the token is toggled BEFORE - * sending data, you must set the opposite value of the token which should come - * first. - */ - -#endif /* __ASSEMBLER__ */ - - -/* ------------------------------------------------------------------------- */ -/* ----------------- Definitions for Descriptor Properties ----------------- */ -/* ------------------------------------------------------------------------- */ -/* This is advanced stuff. See usbconfig-prototype.h for more information - * about the various methods to define USB descriptors. If you do nothing, - * the default descriptors will be used. - */ -#define USB_PROP_IS_DYNAMIC (1 << 14) -/* If this property is set for a descriptor, usbFunctionDescriptor() will be - * used to obtain the particular descriptor. Data directly returned via - * usbMsgPtr are FLASH data by default, combine (OR) with USB_PROP_IS_RAM to - * return RAM data. - */ -#define USB_PROP_IS_RAM (1 << 15) -/* If this property is set for a descriptor, the data is read from RAM - * memory instead of Flash. The property is used for all methods to provide - * external descriptors. - */ -#define USB_PROP_LENGTH(len) ((len) & 0x3fff) -/* If a static external descriptor is used, this is the total length of the - * descriptor in bytes. - */ - -/* all descriptors which may have properties: */ -#ifndef USB_CFG_DESCR_PROPS_DEVICE -#define USB_CFG_DESCR_PROPS_DEVICE 0 -#endif -#ifndef USB_CFG_DESCR_PROPS_CONFIGURATION -#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 -#endif -#ifndef USB_CFG_DESCR_PROPS_STRINGS -#define USB_CFG_DESCR_PROPS_STRINGS 0 -#endif -#ifndef USB_CFG_DESCR_PROPS_STRING_0 -#define USB_CFG_DESCR_PROPS_STRING_0 0 -#endif -#ifndef USB_CFG_DESCR_PROPS_STRING_VENDOR -#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 -#endif -#ifndef USB_CFG_DESCR_PROPS_STRING_PRODUCT -#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 -#endif -#ifndef USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER -#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 -#endif -#ifndef USB_CFG_DESCR_PROPS_HID -#define USB_CFG_DESCR_PROPS_HID 0 -#endif -#if !(USB_CFG_DESCR_PROPS_HID_REPORT) -# undef USB_CFG_DESCR_PROPS_HID_REPORT -# if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH /* do some backward compatibility tricks */ -# define USB_CFG_DESCR_PROPS_HID_REPORT USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH -# else -# define USB_CFG_DESCR_PROPS_HID_REPORT 0 -# endif -#endif -#ifndef USB_CFG_DESCR_PROPS_UNKNOWN -#define USB_CFG_DESCR_PROPS_UNKNOWN 0 -#endif - -/* ------------------ forward declaration of descriptors ------------------- */ -/* If you use external static descriptors, they must be stored in global - * arrays as declared below: - */ -#ifndef __ASSEMBLER__ -extern -#if !(USB_CFG_DESCR_PROPS_DEVICE & USB_PROP_IS_RAM) -PROGMEM -#endif -const char usbDescriptorDevice[]; - -extern -#if !(USB_CFG_DESCR_PROPS_CONFIGURATION & USB_PROP_IS_RAM) -PROGMEM -#endif -const char usbDescriptorConfiguration[]; - -extern -#if !(USB_CFG_DESCR_PROPS_HID_REPORT & USB_PROP_IS_RAM) -PROGMEM -#endif -const char usbDescriptorHidReport[]; - -extern -#if !(USB_CFG_DESCR_PROPS_STRING_0 & USB_PROP_IS_RAM) -PROGMEM -#endif -const char usbDescriptorString0[]; - -extern -#if !(USB_CFG_DESCR_PROPS_STRING_VENDOR & USB_PROP_IS_RAM) -PROGMEM -#endif -const int usbDescriptorStringVendor[]; - -extern -#if !(USB_CFG_DESCR_PROPS_STRING_PRODUCT & USB_PROP_IS_RAM) -PROGMEM -#endif -const int usbDescriptorStringDevice[]; - -extern -#if !(USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER & USB_PROP_IS_RAM) -PROGMEM -#endif -const int usbDescriptorStringSerialNumber[]; - -#endif /* __ASSEMBLER__ */ - -/* ------------------------------------------------------------------------- */ -/* ------------------------ General Purpose Macros ------------------------- */ -/* ------------------------------------------------------------------------- */ - -#define USB_CONCAT(a, b) a ## b -#define USB_CONCAT_EXPANDED(a, b) USB_CONCAT(a, b) - -#define USB_OUTPORT(name) USB_CONCAT(PORT, name) -#define USB_INPORT(name) USB_CONCAT(PIN, name) -#define USB_DDRPORT(name) USB_CONCAT(DDR, name) -/* The double-define trick above lets us concatenate strings which are - * defined by macros. - */ - -/* ------------------------------------------------------------------------- */ -/* ------------------------- Constant definitions -------------------------- */ -/* ------------------------------------------------------------------------- */ - -#if !defined __ASSEMBLER__ && (!defined USB_CFG_VENDOR_ID || !defined USB_CFG_DEVICE_ID) -#warning "You should define USB_CFG_VENDOR_ID and USB_CFG_DEVICE_ID in usbconfig.h" -/* If the user has not defined IDs, we default to obdev's free IDs. - * See USB-IDs-for-free.txt for details. - */ -#endif - -/* make sure we have a VID and PID defined, byte order is lowbyte, highbyte */ -#ifndef USB_CFG_VENDOR_ID -# define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */ -#endif - -#ifndef USB_CFG_DEVICE_ID -# if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH -# define USB_CFG_DEVICE_ID 0xdf, 0x05 /* = 0x5df = 1503, shared PID for HIDs */ -# elif USB_CFG_INTERFACE_CLASS == 2 -# define USB_CFG_DEVICE_ID 0xe1, 0x05 /* = 0x5e1 = 1505, shared PID for CDC Modems */ -# else -# define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x5dc = 1500, obdev's free PID */ -# endif -#endif - -/* Derive Output, Input and DataDirection ports from port names */ -#ifndef USB_CFG_IOPORTNAME -#error "You must define USB_CFG_IOPORTNAME in usbconfig.h, see usbconfig-prototype.h" -#endif - -#define USBOUT USB_OUTPORT(USB_CFG_IOPORTNAME) -#define USB_PULLUP_OUT USB_OUTPORT(USB_CFG_PULLUP_IOPORTNAME) -#define USBIN USB_INPORT(USB_CFG_IOPORTNAME) -#define USBDDR USB_DDRPORT(USB_CFG_IOPORTNAME) -#define USB_PULLUP_DDR USB_DDRPORT(USB_CFG_PULLUP_IOPORTNAME) - -#define USBMINUS USB_CFG_DMINUS_BIT -#define USBPLUS USB_CFG_DPLUS_BIT -#define USBIDLE (1<<USB_CFG_DMINUS_BIT) /* value representing J state */ -#define USBMASK ((1<<USB_CFG_DPLUS_BIT) | (1<<USB_CFG_DMINUS_BIT)) /* mask for USB I/O bits */ - -/* defines for backward compatibility with older driver versions: */ -#define USB_CFG_IOPORT USB_OUTPORT(USB_CFG_IOPORTNAME) -#ifdef USB_CFG_PULLUP_IOPORTNAME -#define USB_CFG_PULLUP_IOPORT USB_OUTPORT(USB_CFG_PULLUP_IOPORTNAME) -#endif - -#ifndef USB_CFG_EP3_NUMBER /* if not defined in usbconfig.h */ -#define USB_CFG_EP3_NUMBER 3 -#endif - -#ifndef USB_CFG_HAVE_INTRIN_ENDPOINT3 -#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0 -#endif - -#define USB_BUFSIZE 11 /* PID, 8 bytes data, 2 bytes CRC */ - -/* ----- Try to find registers and bits responsible for ext interrupt 0 ----- */ - -#ifndef USB_INTR_CFG /* allow user to override our default */ -# if defined EICRA -# define USB_INTR_CFG EICRA -# else -# define USB_INTR_CFG MCUCR -# endif -#endif -#ifndef USB_INTR_CFG_SET /* allow user to override our default */ -# if defined(USB_COUNT_SOF) || defined(USB_SOF_HOOK) -# define USB_INTR_CFG_SET (1 << ISC01) /* cfg for falling edge */ - /* If any SOF logic is used, the interrupt must be wired to D- where - * we better trigger on falling edge - */ -# else -# define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) /* cfg for rising edge */ -# endif -#endif -#ifndef USB_INTR_CFG_CLR /* allow user to override our default */ -# define USB_INTR_CFG_CLR 0 /* no bits to clear */ -#endif - -#ifndef USB_INTR_ENABLE /* allow user to override our default */ -# if defined GIMSK -# define USB_INTR_ENABLE GIMSK -# elif defined EIMSK -# define USB_INTR_ENABLE EIMSK -# else -# define USB_INTR_ENABLE GICR -# endif -#endif -#ifndef USB_INTR_ENABLE_BIT /* allow user to override our default */ -# define USB_INTR_ENABLE_BIT INT0 -#endif - -#ifndef USB_INTR_PENDING /* allow user to override our default */ -# if defined EIFR -# define USB_INTR_PENDING EIFR -# else -# define USB_INTR_PENDING GIFR -# endif -#endif -#ifndef USB_INTR_PENDING_BIT /* allow user to override our default */ -# define USB_INTR_PENDING_BIT INTF0 -#endif - -/* -The defines above don't work for the following chips -at90c8534: no ISC0?, no PORTB, can't find a data sheet -at86rf401: no PORTB, no MCUCR etc, low clock rate -atmega103: no ISC0? (maybe omission in header, can't find data sheet) -atmega603: not defined in avr-libc -at43usb320, at43usb355, at76c711: have USB anyway -at94k: is different... - -at90s1200, attiny11, attiny12, attiny15, attiny28: these have no RAM -*/ - -/* ------------------------------------------------------------------------- */ -/* ----------------- USB Specification Constants and Types ----------------- */ -/* ------------------------------------------------------------------------- */ - -/* USB Token values */ -#define USBPID_SETUP 0x2d -#define USBPID_OUT 0xe1 -#define USBPID_IN 0x69 -#define USBPID_DATA0 0xc3 -#define USBPID_DATA1 0x4b - -#define USBPID_ACK 0xd2 -#define USBPID_NAK 0x5a -#define USBPID_STALL 0x1e - -#ifndef USB_INITIAL_DATATOKEN -#define USB_INITIAL_DATATOKEN USBPID_DATA1 -#endif - -#ifndef __ASSEMBLER__ - -typedef struct usbTxStatus{ - volatile uchar len; - uchar buffer[USB_BUFSIZE]; -}usbTxStatus_t; - -extern usbTxStatus_t usbTxStatus1, usbTxStatus3; -#define usbTxLen1 usbTxStatus1.len -#define usbTxBuf1 usbTxStatus1.buffer -#define usbTxLen3 usbTxStatus3.len -#define usbTxBuf3 usbTxStatus3.buffer - - -typedef union usbWord{ - unsigned word; - uchar bytes[2]; -}usbWord_t; - -typedef struct usbRequest{ - uchar bmRequestType; - uchar bRequest; - usbWord_t wValue; - usbWord_t wIndex; - usbWord_t wLength; -}usbRequest_t; -/* This structure matches the 8 byte setup request */ -#endif - -/* bmRequestType field in USB setup: - * d t t r r r r r, where - * d ..... direction: 0=host->device, 1=device->host - * t ..... type: 0=standard, 1=class, 2=vendor, 3=reserved - * r ..... recipient: 0=device, 1=interface, 2=endpoint, 3=other - */ - -/* USB setup recipient values */ -#define USBRQ_RCPT_MASK 0x1f -#define USBRQ_RCPT_DEVICE 0 -#define USBRQ_RCPT_INTERFACE 1 -#define USBRQ_RCPT_ENDPOINT 2 - -/* USB request type values */ -#define USBRQ_TYPE_MASK 0x60 -#define USBRQ_TYPE_STANDARD (0<<5) -#define USBRQ_TYPE_CLASS (1<<5) -#define USBRQ_TYPE_VENDOR (2<<5) - -/* USB direction values: */ -#define USBRQ_DIR_MASK 0x80 -#define USBRQ_DIR_HOST_TO_DEVICE (0<<7) -#define USBRQ_DIR_DEVICE_TO_HOST (1<<7) - -/* USB Standard Requests */ -#define USBRQ_GET_STATUS 0 -#define USBRQ_CLEAR_FEATURE 1 -#define USBRQ_SET_FEATURE 3 -#define USBRQ_SET_ADDRESS 5 -#define USBRQ_GET_DESCRIPTOR 6 -#define USBRQ_SET_DESCRIPTOR 7 -#define USBRQ_GET_CONFIGURATION 8 -#define USBRQ_SET_CONFIGURATION 9 -#define USBRQ_GET_INTERFACE 10 -#define USBRQ_SET_INTERFACE 11 -#define USBRQ_SYNCH_FRAME 12 - -/* USB descriptor constants */ -#define USBDESCR_DEVICE 1 -#define USBDESCR_CONFIG 2 -#define USBDESCR_STRING 3 -#define USBDESCR_INTERFACE 4 -#define USBDESCR_ENDPOINT 5 -#define USBDESCR_HID 0x21 -#define USBDESCR_HID_REPORT 0x22 -#define USBDESCR_HID_PHYS 0x23 - -//#define USBATTR_BUSPOWER 0x80 // USB 1.1 does not define this value any more -#define USBATTR_SELFPOWER 0x40 -#define USBATTR_REMOTEWAKE 0x20 - -/* USB HID Requests */ -#define USBRQ_HID_GET_REPORT 0x01 -#define USBRQ_HID_GET_IDLE 0x02 -#define USBRQ_HID_GET_PROTOCOL 0x03 -#define USBRQ_HID_SET_REPORT 0x09 -#define USBRQ_HID_SET_IDLE 0x0a -#define USBRQ_HID_SET_PROTOCOL 0x0b - -/* ------------------------------------------------------------------------- */ - -#endif /* __usbdrv_h_included__ */ |