summaryrefslogtreecommitdiff
path: root/protocol/usb_hid/test/Makefile
diff options
context:
space:
mode:
Diffstat (limited to 'protocol/usb_hid/test/Makefile')
-rw-r--r--protocol/usb_hid/test/Makefile126
1 files changed, 0 insertions, 126 deletions
diff --git a/protocol/usb_hid/test/Makefile b/protocol/usb_hid/test/Makefile
deleted file mode 100644
index 83bf2aed67..0000000000
--- a/protocol/usb_hid/test/Makefile
+++ /dev/null
@@ -1,126 +0,0 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-# Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-# (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-# have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-# have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-# (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-# (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging,
-# with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-# bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# Target file name (without extension).
-TARGET = usb_hid_test
-
-TMK_DIR = ../../..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# MCU name
-MCU = atmega32u4
-
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-# Interrupt driven control endpoint task
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-
-# Build Options
-# comment out to disable the options.
-#
-# Console for debug
-OPT_DEFS += -DCONSOLE_ENABLE
-
-# Boot Section Size in bytes
-# Teensy halfKay 512
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-#OPT_DEFS += -DBOOT_SIZE=4096
-
-
-
-SRC = test.cpp
-SRC += common/debug.c
-SRC += common/print.c
-
-CONFIG_H = config.h
-
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-VPATH += $(TMK_DIR)/common
-
-
-
-# program Leonardo
-PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -P$(DEV) -b57600 -Uflash:w:$(TARGET).hex
-
-
-
-include $(TMK_DIR)/protocol/usb_hid.mk
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/rules.mk