diff options
Diffstat (limited to 'protocol/usb_hid/USB_Host_Shield_2.0/cdc_XR21B1411.h')
m--------- | protocol/usb_hid/USB_Host_Shield_2.0 | 0 | ||||
-rw-r--r-- | protocol/usb_hid/USB_Host_Shield_2.0/cdc_XR21B1411.h | 272 |
2 files changed, 272 insertions, 0 deletions
diff --git a/protocol/usb_hid/USB_Host_Shield_2.0 b/protocol/usb_hid/USB_Host_Shield_2.0 deleted file mode 160000 -Subproject 7c2e6c1bcdcc22cfdbd82edd9d8fc4c4276ead4 diff --git a/protocol/usb_hid/USB_Host_Shield_2.0/cdc_XR21B1411.h b/protocol/usb_hid/USB_Host_Shield_2.0/cdc_XR21B1411.h new file mode 100644 index 0000000000..c32627544f --- /dev/null +++ b/protocol/usb_hid/USB_Host_Shield_2.0/cdc_XR21B1411.h @@ -0,0 +1,272 @@ +/* Copyright (C) 2015 Andrew J. Kroll + and + Circuits At Home, LTD. All rights reserved. + +This software may be distributed and modified under the terms of the GNU +General Public License version 2 (GPL2) as published by the Free Software +Foundation and appearing in the file GPL2.TXT included in the packaging of +this file. Please note that GPL2 Section 2[b] requires that all works based +on this software must also be made publicly available under the terms of +the GPL2 ("Copyleft"). + +Contact information +------------------- + +Circuits At Home, LTD +Web : http://www.circuitsathome.com +e-mail : support@circuitsathome.com + */ +#if !defined(__CDC_XR21B1411_H__) +#define __CDC_XR21B1411_H__ + +#include "cdcacm.h" + +#define XR_REG_CUSTOM_DRIVER (0x020DU) // DRIVER SELECT +#define XR_REG_CUSTOM_DRIVER_ACTIVE (0x0001U) // 0: CDC 1: CUSTOM + +#define XR_REG_ACM_FLOW_CTL (0x0216U) // FLOW CONTROL REGISTER CDCACM MODE +#define XR_REG_FLOW_CTL (0x0C06U) // FLOW CONTROL REGISTER CUSTOM MODE +#define XR_REG_FLOW_CTL_HALF_DPLX (0x0008U) // 0:FULL DUPLEX 1:HALF DUPLEX +#define XR_REG_FLOW_CTL_MODE_MASK (0x0007U) // MODE BITMASK +#define XR_REG_FLOW_CTL_NONE (0x0000U) // NO FLOW CONTROL +#define XR_REG_FLOW_CTL_HW (0x0001U) // HARDWARE FLOW CONTROL +#define XR_REG_FLOW_CTL_SW (0x0002U) // SOFTWARE FLOW CONTROL +#define XR_REG_FLOW_CTL_MMMRX (0x0003U) // MULTIDROP RX UPON ADDRESS MATCH +#define XR_REG_FLOW_CTL_MMMRXTX (0x0004U) // MULTIDROP RX/TX UPON ADDRESS MATCH + +#define XR_REG_ACM_GPIO_MODE (0x0217U) // GPIO MODE REGISTER IN CDCACM MODE +#define XR_REG_GPIO_MODE (0x0C0CU) // GPIO MODE REGISTER IN CUSTOM MODE +#define XR_REG_GPIO_MODE_GPIO (0x0000U) // ALL GPIO PINS ACM PROGRAMMABLE +#define XR_REG_GPIO_MODE_FC_RTSCTS (0x0001U) // AUTO RTSCTS HW FC (GPIO 4/5) +#define XR_REG_GPIO_MODE_FC_DTRDSR (0x0002U) // AUTO DTRDSR HW FC (GPIO 2/3) +#define XR_REG_GPIO_MODE_ATE (0x0003U) // AUTO TRANSCEIVER ENABLE DURING TX (GPIO 5) +#define XR_REG_GPIO_MODE_ATE_ADDRESS (0x0004U) // AUTO TRANSCEIVER ENABLE ON ADDRESS MATCH (GPIO 5) + +#define XR_REG_ACM_GPIO_DIR (0x0218U) // GPIO DIRECTION REGISTER CDCACM MODE, 0:IN 1:OUT +#define XR_REG_GPIO_DIR (0x0C0DU) // GPIO DIRECTION REGISTER CUSTOM MODE, 0:IN 1:OUT + +#define XR_REG_ACM_GPIO_INT (0x0219U) // GPIO PIN CHANGE INTERRUPT ENABLE CDCACM MODE, 0: ENABLED 1: DISABLED +#define XR_REG_GPIO_INT (0x0C11U) // GPIO PIN CHANGE INTERRUPT ENABLE CUSTOM MODE, 0: ENABLED 1: DISABLED +#define XR_REG_GPIO_MASK (0x001FU) // GPIO REGISTERS BITMASK + +#define XR_REG_UART_ENABLE (0x0C00U) // UART I/O ENABLE REGISTER +#define XR_REG_UART_ENABLE_RX (0x0002U) // 0:DISABLED 1:ENABLED +#define XR_REG_UART_ENABLE_TX (0x0001U) // 0:DISABLED 1:ENABLED + +#define XR_REG_ERROR_STATUS (0x0C09U) // ERROR STATUS REGISTER +#define XR_REG_ERROR_STATUS_MASK (0x00F8U) // ERROR STATUS BITMASK +#define XR_REG_ERROR_STATUS_ERROR (0x0078U) // ERROR STATUS ERROR BITMASK +#define XR_REG_ERROR_STATUS_BREAK (0x0008U) // BREAK ERROR HAS BEEN DETECTED +#define XR_REG_ERROR_STATUS_FRAME (0x0010U) // FRAMING ERROR HAS BEEN DETECTED +#define XR_REG_ERROR_STATUS_PARITY (0x0020U) // PARITY ERROR HAS BEEN DETECTED +#define XR_REG_ERROR_STATUS_OVERRUN (0x0040U) // RX OVERRUN ERROR HAS BEEN DETECTED +#define XR_REG_ERROR_STATUS_BREAK_STATUS (0x0080U) // BREAK CONDITION IS CURRENTLY BEING DETECTED + +#define XR_REG_TX_BREAK (0x0C0AU) // TRANSMIT BREAK. 0X0001-0XFFE TIME IN MS, 0X0000 STOP, 0X0FFF BREAK ON + +#define XR_REG_XCVR_EN_DELAY (0x0C0BU) // TURN-ARROUND DELAY IN BIT-TIMES 0X0000-0X000F + +#define XR_REG_GPIO_SET (0x0C0EU) // 1:SET GPIO PIN + +#define XR_REG_GPIO_CLR (0x0C0FU) // 1:CLEAR GPIO PIN + +#define XR_REG_GPIO_STATUS (0x0C10U) // READ GPIO PINS + +#define XR_REG_CUSTOMISED_INT (0x0C12U) // 0:STANDARD 1:CUSTOM SEE DATA SHEET + +#define XR_REG_PIN_PULLUP_ENABLE (0x0C14U) // 0:DISABLE 1:ENABLE, BITS 0-5:GPIO, 6:RX 7:TX + +#define XR_REG_PIN_PULLDOWN_ENABLE (0x0C15U) // 0:DISABLE 1:ENABLE, BITS 0-5:GPIO, 6:RX 7:TX + +#define XR_REG_LOOPBACK (0x0C16U) // 0:DISABLE 1:ENABLE, SEE DATA SHEET + +#define XR_REG_RX_FIFO_LATENCY (0x0CC2U) // FIFO LATENCY REGISTER +#define XR_REG_RX_FIFO_LATENCY_ENABLE (0x0001U) // + +#define XR_REG_WIDE_MODE (0x0D02U) +#define XR_REG_WIDE_MODE_ENABLE (0x0001U) + +#define XR_REG_XON_CHAR (0x0C07U) +#define XR_REG_XOFF_CHAR (0x0C08U) + +#define XR_REG_TX_FIFO_RESET (0x0C80U) // 1: RESET, SELF-CLEARING +#define XR_REG_TX_FIFO_COUNT (0x0C81U) // READ-ONLY +#define XR_REG_RX_FIFO_RESET (0x0CC0U) // 1: RESET, SELF-CLEARING +#define XR_REG_RX_FIFO_COUNT (0x0CC1U) // READ-ONLY + +#define XR_WRITE_REQUEST_TYPE (0x40U) + +#define XR_READ_REQUEST_TYPE (0xC0U) + +#define XR_MAX_ENDPOINTS 4 + +class XR21B1411 : public ACM { +protected: + +public: + XR21B1411(USB *pusb, CDCAsyncOper *pasync); + + /** + * Used by the USB core to check what this driver support. + * @param vid The device's VID. + * @param pid The device's PID. + * @return Returns true if the device's VID and PID matches this driver. + */ + virtual bool VIDPIDOK(uint16_t vid, uint16_t pid) { + return (((vid == 0x2890U) && (pid == 0x0201U)) || ((vid == 0x04e2U) && (pid == 0x1411U))); + }; + + uint8_t Init(uint8_t parent, uint8_t port, bool lowspeed); + + virtual tty_features enhanced_features(void) { + tty_features rv; + rv.enhanced = true; + rv.autoflow_RTS = true; + rv.autoflow_DSR = true; + rv.autoflow_XON = true; + rv.half_duplex = true; + rv.wide = true; + return rv; + }; + + uint8_t read_register(uint16_t reg, uint16_t *val) { + return (pUsb->ctrlReq(bAddress, 0, XR_READ_REQUEST_TYPE, 1, 0, 0, reg, 2, 2, (uint8_t *)val, NULL)); + } + + uint8_t write_register(uint16_t reg, uint16_t val) { + return (pUsb->ctrlReq(bAddress, 0, XR_WRITE_REQUEST_TYPE, 0, BGRAB0(val), BGRAB1(val), reg, 0, 0, NULL, NULL)); + } + + + //////////////////////////////////////////////////////////////////////// + // The following methods set the CDC-ACM defaults. + //////////////////////////////////////////////////////////////////////// + + virtual void autoflowRTS(bool s) { + uint16_t val; + uint8_t rval; + rval = read_register(XR_REG_ACM_FLOW_CTL, &val); + if(!rval) { + if(s) { + val &= XR_REG_FLOW_CTL_HALF_DPLX; + val |= XR_REG_FLOW_CTL_HW; + } else { + val &= XR_REG_FLOW_CTL_HALF_DPLX; + } + rval = write_register(XR_REG_ACM_FLOW_CTL, val); + if(!rval) { + rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_GPIO); + if(!rval) { + // ACM commands apply the new settings. + LINE_CODING LCT; + rval = GetLineCoding(&LCT); + if(!rval) { + rval = SetLineCoding(&LCT); + if(!rval) { + _enhanced_status.autoflow_XON = false; + _enhanced_status.autoflow_DSR = false; + _enhanced_status.autoflow_RTS = s; + } + } + } + } + } + }; + + virtual void autoflowDSR(bool s) { + uint16_t val; + uint8_t rval; + rval = read_register(XR_REG_ACM_FLOW_CTL, &val); + if(!rval) { + if(s) { + val &= XR_REG_FLOW_CTL_HALF_DPLX; + val |= XR_REG_FLOW_CTL_HW; + } else { + val &= XR_REG_FLOW_CTL_HALF_DPLX; + } + rval = write_register(XR_REG_ACM_FLOW_CTL, val); + if(!rval) { + if(s) { + rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_FC_DTRDSR); + } else { + rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_GPIO); + } + if(!rval) { + // ACM commands apply the new settings. + LINE_CODING LCT; + rval = GetLineCoding(&LCT); + if(!rval) { + rval = SetLineCoding(&LCT); + if(!rval) { + _enhanced_status.autoflow_XON = false; + _enhanced_status.autoflow_RTS = false; + _enhanced_status.autoflow_DSR = s; + } + } + } + } + } + }; + + virtual void autoflowXON(bool s) { + // NOTE: hardware defaults to the normal XON/XOFF + uint16_t val; + uint8_t rval; + rval = read_register(XR_REG_ACM_FLOW_CTL, &val); + if(!rval) { + if(s) { + val &= XR_REG_FLOW_CTL_HALF_DPLX; + val |= XR_REG_FLOW_CTL_SW; + } else { + val &= XR_REG_FLOW_CTL_HALF_DPLX; + } + rval = write_register(XR_REG_ACM_FLOW_CTL, val); + if(!rval) { + rval = write_register(XR_REG_ACM_GPIO_MODE, XR_REG_GPIO_MODE_GPIO); + if(!rval) { + // ACM commands apply the new settings. + LINE_CODING LCT; + rval = GetLineCoding(&LCT); + if(!rval) { + rval = SetLineCoding(&LCT); + if(!rval) { + _enhanced_status.autoflow_RTS = false; + _enhanced_status.autoflow_DSR = false; + _enhanced_status.autoflow_XON = s; + } + } + } + } + } + }; + + virtual void half_duplex(bool s) { + uint16_t val; + uint8_t rval; + rval = read_register(XR_REG_ACM_FLOW_CTL, &val); + if(!rval) { + if(s) { + val |= XR_REG_FLOW_CTL_HALF_DPLX; + } else { + val &= XR_REG_FLOW_CTL_MODE_MASK; + } + rval = write_register(XR_REG_ACM_FLOW_CTL, val); + if(!rval) { + // ACM commands apply the new settings. + LINE_CODING LCT; + rval = GetLineCoding(&LCT); + if(!rval) { + rval = SetLineCoding(&LCT); + if(!rval) { + _enhanced_status.half_duplex = s; + } + } + } + } + }; + + + +}; + +#endif // __CDCPROLIFIC_H__ |