diff options
Diffstat (limited to 'protocol/lufa/LUFA-git/LUFA/Drivers/Peripheral/XMEGA/TWI_XMEGA.h')
| m--------- | protocol/lufa/LUFA-git | 0 | ||||
| -rw-r--r-- | protocol/lufa/LUFA-git/LUFA/Drivers/Peripheral/XMEGA/TWI_XMEGA.h | 302 |
2 files changed, 302 insertions, 0 deletions
diff --git a/protocol/lufa/LUFA-git b/protocol/lufa/LUFA-git deleted file mode 160000 -Subproject b6c18b2a7c544653efbe12a1d4e8ba65e7d83c3 diff --git a/protocol/lufa/LUFA-git/LUFA/Drivers/Peripheral/XMEGA/TWI_XMEGA.h b/protocol/lufa/LUFA-git/LUFA/Drivers/Peripheral/XMEGA/TWI_XMEGA.h new file mode 100644 index 0000000000..72437e5e15 --- /dev/null +++ b/protocol/lufa/LUFA-git/LUFA/Drivers/Peripheral/XMEGA/TWI_XMEGA.h @@ -0,0 +1,302 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2014. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2014 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaims all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief TWI Peripheral Driver (XMEGA) + * + * On-chip TWI driver for the XMEGA Family of AVR microcontrollers. + * + * \note This file should not be included directly. It is automatically included as needed by the TWI driver + * dispatch header located in LUFA/Drivers/Peripheral/TWI.h. + */ + +/** \ingroup Group_TWI + * \defgroup Group_TWI_XMEGA TWI Peripheral Driver (XMEGA) + * + * \section Sec_TWI_XMEGA_ModDescription Module Description + * Master mode TWI driver for the 8-bit AVR microcontrollers which contain a hardware TWI module. + * + * \note This file should not be included directly. It is automatically included as needed by the TWI driver + * dispatch header located in LUFA/Drivers/Peripheral/TWI.h. + * + * \section Sec_TWI_XMEGA_ExampleUsage Example Usage + * The following snippet is an example of how this module may be used within a typical + * application. + * + * <b>Low Level API Example:</b> + * \code + * // Initialize the TWI driver before first use at 200KHz + * TWI_Init(&TWIC, TWI_BAUD_FROM_FREQ(200000)); + * + * // Start a write session to device at device address 0xA0, internal address 0xDC with a 10ms timeout + * if (TWI_StartTransmission(&TWIC, 0xA0 | TWI_ADDRESS_WRITE, 10) == TWI_ERROR_NoError) + * { + * TWI_SendByte(&TWIC, 0xDC); + * + * TWI_SendByte(&TWIC, 0x01); + * TWI_SendByte(&TWIC, 0x02); + * TWI_SendByte(&TWIC, 0x03); + * + * // Must stop transmission afterwards to release the bus + * TWI_StopTransmission(&TWIC); + * } + * + * // Start a read session to device at address 0xA0, internal address 0xDC with a 10ms timeout + * if (TWI_StartTransmission(&TWIC, 0xA0 | TWI_ADDRESS_WRITE, 10) == TWI_ERROR_NoError) + * { + * TWI_SendByte(&TWIC, 0xDC); + * TWI_StopTransmission(&TWIC); + * + * if (TWI_StartTransmission(&TWIC, 0xA0 | TWI_ADDRESS_READ, 10) == TWI_ERROR_NoError) + * { + * uint8_t Byte1, Byte2, Byte3; + * + * // Read three bytes, acknowledge after the third byte is received + * TWI_ReceiveByte(&TWIC, &Byte1, false); + * TWI_ReceiveByte(&TWIC, &Byte2, false); + * TWI_ReceiveByte(&TWIC, &Byte3, true); + * + * // Must stop transmission afterwards to release the bus + * TWI_StopTransmission(&TWIC); + * } + * } + * \endcode + * + * <b>High Level API Example:</b> + * \code + * // Initialize the TWI driver before first use at 200KHz + * TWI_Init(&TWIC, TWI_BAUD_FROM_FREQ(200000)); + * + * // Start a write session to device at device address 0xA0, internal address 0xDC with a 10ms timeout + * uint8_t InternalWriteAddress = 0xDC; + * uint8_t WritePacket[3] = {0x01, 0x02, 0x03}; + * + * TWI_WritePacket(&TWIC, 0xA0, 10, &InternalWriteAddress, sizeof(InternalWriteAddress), + * &WritePacket, sizeof(WritePacket); + * + * // Start a read session to device at address 0xA0, internal address 0xDC with a 10ms timeout + * uint8_t InternalReadAddress = 0xDC; + * uint8_t ReadPacket[3]; + * + * TWI_ReadPacket(&TWIC, 0xA0, 10, &InternalReadAddress, sizeof(InternalReadAddress), + * &ReadPacket, sizeof(ReadPacket); + * \endcode + * + * @{ + */ + +#ifndef __TWI_XMEGA_H__ +#define __TWI_XMEGA_H__ + + /* Includes: */ + #include "../../../Common/Common.h" + + #include <stdio.h> + + /* Enable C linkage for C++ Compilers: */ + #if defined(__cplusplus) + extern "C" { + #endif + + /* Preprocessor Checks: */ + #if !defined(__INCLUDE_FROM_TWI_H) && !defined(__INCLUDE_FROM_TWI_C) + #error Do not include this file directly. Include LUFA/Drivers/Peripheral/TWI.h instead. + #endif + + /* Public Interface - May be used in end-application: */ + /* Macros: */ + /** TWI slave device address mask for a read session. Mask with a slave device base address to obtain + * the correct TWI bus address for the slave device when reading data from it. + */ + #define TWI_ADDRESS_READ 0x01 + + /** TWI slave device address mask for a write session. Mask with a slave device base address to obtain + * the correct TWI bus address for the slave device when writing data to it. + */ + #define TWI_ADDRESS_WRITE 0x00 + + /** Mask to retrieve the base address for a TWI device, which can then be ORed with \ref TWI_ADDRESS_READ + * or \ref TWI_ADDRESS_WRITE to obtain the device's read and write address respectively. + */ + #define TWI_DEVICE_ADDRESS_MASK 0xFE + + /** Calculates the length of each bit on the TWI bus for a given target frequency. This may be used with + * the \ref TWI_Init() function to convert a bus frequency to a number of clocks for the \c BitLength + * parameter. + * + * \param[in] Frequency Desired TWI bus frequency in Hz. + * + * \return Bit length in clocks for the given TWI bus frequency at the given prescaler value. + */ + #define TWI_BAUD_FROM_FREQ(Frequency) ((F_CPU / (2 * Frequency)) - 5) + + /* Enums: */ + /** Enum for the possible return codes of the TWI transfer start routine and other dependant TWI functions. */ + enum TWI_ErrorCodes_t + { + TWI_ERROR_NoError = 0, /**< Indicates that the command completed successfully. */ + TWI_ERROR_BusFault = 1, /**< A TWI bus fault occurred while attempting to capture the bus. */ + TWI_ERROR_BusCaptureTimeout = 2, /**< A timeout occurred whilst waiting for the bus to be ready. */ + TWI_ERROR_SlaveResponseTimeout = 3, /**< No ACK received at the nominated slave address within the timeout period. */ + TWI_ERROR_SlaveNotReady = 4, /**< Slave NAKed the TWI bus START condition. */ + TWI_ERROR_SlaveNAK = 5, /**< Slave NAKed whilst attempting to send data to the device. */ + }; + + /* Inline Functions: */ + /** Initializes the TWI hardware into master mode, ready for data transmission and reception. This must be + * before any other TWI operations. + * + * The generated SCL frequency will be according to the formula <pre>F_CPU / (2 * (5 + (BAUD)))</pre>. + * + * \attention The value of the \c BitLength parameter should not be set below 10 or invalid bus conditions may + * occur, as indicated in the XMEGA microcontroller datasheet. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + * \param[in] Baud Value of the BAUD register of the TWI Master. + */ + static inline void TWI_Init(TWI_t* const TWI, + const uint8_t Baud) ATTR_ALWAYS_INLINE ATTR_NON_NULL_PTR_ARG(1); + static inline void TWI_Init(TWI_t* const TWI, + const uint8_t Baud) + { + TWI->CTRL = 0x00; + TWI->MASTER.BAUD = Baud; + TWI->MASTER.CTRLA = TWI_MASTER_ENABLE_bm; + TWI->MASTER.CTRLB = 0; + TWI->MASTER.STATUS = TWI_MASTER_BUSSTATE_IDLE_gc; + } + + /** Turns off the TWI driver hardware. If this is called, any further TWI operations will require a call to + * \ref TWI_Init() before the TWI can be used again. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + */ + static inline void TWI_Disable(TWI_t* const TWI) ATTR_ALWAYS_INLINE ATTR_NON_NULL_PTR_ARG(1); + static inline void TWI_Disable(TWI_t* const TWI) + { + TWI->MASTER.CTRLA &= ~TWI_MASTER_ENABLE_bm; + } + + /** Sends a TWI STOP onto the TWI bus, terminating communication with the currently addressed device. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + */ + static inline void TWI_StopTransmission(TWI_t* const TWI) ATTR_ALWAYS_INLINE ATTR_NON_NULL_PTR_ARG(1); + static inline void TWI_StopTransmission(TWI_t* const TWI) + { + TWI->MASTER.CTRLC = TWI_MASTER_ACKACT_bm | TWI_MASTER_CMD_STOP_gc; + } + + /* Function Prototypes: */ + /** Begins a master mode TWI bus communication with the given slave device address. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + * \param[in] SlaveAddress Address of the slave TWI device to communicate with. + * \param[in] TimeoutMS Timeout period within which the slave must respond, in milliseconds. + * + * \return A value from the \ref TWI_ErrorCodes_t enum. + */ + uint8_t TWI_StartTransmission(TWI_t* const TWI, + const uint8_t SlaveAddress, + const uint8_t TimeoutMS) ATTR_NON_NULL_PTR_ARG(1); + + /** Sends a byte to the currently addressed device on the TWI bus. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + * \param[in] Byte Byte to send to the currently addressed device + * + * \return Boolean \c true if the recipient ACKed the byte, \c false otherwise + */ + bool TWI_SendByte(TWI_t* const TWI, + const uint8_t Byte) ATTR_NON_NULL_PTR_ARG(1); + + /** Receives a byte from the currently addressed device on the TWI bus. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + * \param[in] Byte Location where the read byte is to be stored. + * \param[in] LastByte Indicates if the byte should be ACKed if false, NAKed if true. + * + * \return Boolean \c true if the byte reception successfully completed, \c false otherwise. + */ + bool TWI_ReceiveByte(TWI_t* const TWI, + uint8_t* const Byte, + const bool LastByte) ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(2); + + /** High level function to perform a complete packet transfer over the TWI bus to the specified + * device. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + * \param[in] SlaveAddress Base address of the TWI slave device to communicate with. + * \param[in] TimeoutMS Timeout for bus capture and slave START ACK, in milliseconds. + * \param[in] InternalAddress Pointer to a location where the internal slave read start address is stored. + * \param[in] InternalAddressLen Size of the internal device address, in bytes. + * \param[in] Buffer Pointer to a buffer where the read packet data is to be stored. + * \param[in] Length Size of the packet to read, in bytes. + * + * \return A value from the \ref TWI_ErrorCodes_t enum. + */ + uint8_t TWI_ReadPacket(TWI_t* const TWI, + const uint8_t SlaveAddress, + const uint8_t TimeoutMS, + const uint8_t* InternalAddress, + uint8_t InternalAddressLen, + uint8_t* Buffer, + uint8_t Length) ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(4); + + /** High level function to perform a complete packet transfer over the TWI bus from the specified + * device. + * + * \param[in] TWI Pointer to the base of the TWI peripheral within the device. + * \param[in] SlaveAddress Base address of the TWI slave device to communicate with + * \param[in] TimeoutMS Timeout for bus capture and slave START ACK, in milliseconds + * \param[in] InternalAddress Pointer to a location where the internal slave write start address is stored + * \param[in] InternalAddressLen Size of the internal device address, in bytes + * \param[in] Buffer Pointer to a buffer where the packet data to send is stored + * \param[in] Length Size of the packet to send, in bytes + * + * \return A value from the \ref TWI_ErrorCodes_t enum. + */ + uint8_t TWI_WritePacket(TWI_t* const TWI, + const uint8_t SlaveAddress, + const uint8_t TimeoutMS, + const uint8_t* InternalAddress, + uint8_t InternalAddressLen, + const uint8_t* Buffer, + uint8_t Length) ATTR_NON_NULL_PTR_ARG(1) ATTR_NON_NULL_PTR_ARG(4); + + /* Disable C linkage for C++ Compilers: */ + #if defined(__cplusplus) + } + #endif + +#endif + +/** @} */ + |