diff options
Diffstat (limited to 'protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderMassStorage.txt')
m--------- | protocol/lufa/LUFA-git | 0 | ||||
-rw-r--r-- | protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderMassStorage.txt | 225 |
2 files changed, 225 insertions, 0 deletions
diff --git a/protocol/lufa/LUFA-git b/protocol/lufa/LUFA-git deleted file mode 160000 -Subproject b6c18b2a7c544653efbe12a1d4e8ba65e7d83c3 diff --git a/protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderMassStorage.txt b/protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderMassStorage.txt new file mode 100644 index 0000000000..e094847933 --- /dev/null +++ b/protocol/lufa/LUFA-git/Bootloaders/MassStorage/BootloaderMassStorage.txt @@ -0,0 +1,225 @@ +/** \file + * + * This file contains special DoxyGen information for the generation of the main page and other special + * documentation pages. It is not a project source file. + */ + +/** \mainpage Mass Storage Class USB AVR Bootloader + * + * \section Sec_Compat Demo Compatibility: + * + * The following list indicates what microcontrollers are compatible with this demo. + * + * \li Series 7 USB AVRs (AT90USBxxx7) + * \li Series 6 USB AVRs (AT90USBxxx6) + * \li Series 4 USB AVRs (ATMEGAxxU4) - <i>See \ref SSec_Aux_Space</i> + * \li ATMEGA32U2 - <i>See \ref SSec_Aux_Space</i> + * + * \section Sec_Info USB Information: + * + * The following table gives a rundown of the USB utilization of this demo. + * + * <table> + * <tr> + * <td><b>USB Mode:</b></td> + * <td>Device</td> + * </tr> + * <tr> + * <td><b>USB Class:</b></td> + * <td>Mass Storage Device</td> + * </tr> + * <tr> + * <td><b>USB Subclass:</b></td> + * <td>Bulk-Only Transport</td> + * </tr> + * <tr> + * <td><b>Relevant Standards:</b></td> + * <td>USBIF Mass Storage Standard \n + * USB Bulk-Only Transport Standard \n + * SCSI Primary Commands Specification \n + * SCSI Block Commands Specification</td> + * </tr> + * <tr> + * <td><b>Supported USB Speeds:</b></td> + * <td>Full Speed Mode</td> + * </tr> + * </table> + * + * \section Sec_Description Project Description: + * + * This bootloader enumerates to the host as a Mass Storage device, capable of reading and writing a new binary + * firmware image file, to load firmware onto the AVR. + * + * Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit + * into 6KB of bootloader space. If you wish to alter this size and/or change the AVR model, you will need to + * edit the MCU, FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile. + * + * When the bootloader is running, the board's LED(s) will flash at regular intervals to distinguish the + * bootloader from the normal user application. + * + * \warning <b>THIS BOOTLOADER IS NOT SECURE.</b> Malicious entities can recover written data, even if the device + * lockbits are set. + * + * \section Sec_Running Running the Bootloader + * + * This bootloader is designed to be started via the HWB mechanism of the USB AVRs; ground the HWB pin (see device + * datasheet) then momentarily ground /RESET to start the bootloader. This assumes the HWBE fuse is set and the BOOTRST + * fuse is cleared. + * + * For board specific exceptions to the above, see below. + * + * \subsection SSec_XPLAIN Atmel Xplain Board + * Ground the USB AVR JTAG's \c TCK pin to ground when powering on the board to start the bootloader. This assumes the + * \c HWBE fuse is cleared and the \c BOOTRST fuse is set as the HWBE pin is not user accessible on this board. + * + * \subsection SSec_Leonardo Arduino Leonardo Board + * Ground \c IO13 when powering the board to start the bootloader. This assumes the \c HWBE fuse is cleared and the + * \c BOOTRST fuse is set as the HWBE pin is not user accessible on this board. + * + * \section Sec_Installation Driver Installation + * + * This bootloader uses the Mass Storage drivers inbuilt into all modern operating systems, thus no additional + * drivers need to be supplied for correct operation. + * + * \section Sec_HostApp Host Controller Application + * + * This bootloader is compatible with all operating systems that support the FAT12 file system format. To reprogram the + * device, overwrite a file stored on the virtual FAT filesystem with a new binary (BIN format) image. Remember to safely + * remove your device from the host using the host OS's ejection APIs, to ensure all data is correctly flushed to the + * bootloader's virtual filesystem and not cached in the OS's file system driver. + * + * The current device firmware can be read from the device by reading a file from the virtual FAT filesystem. + * + * \warning This bootloader is currently <b>incompatible with the Apple MacOS X OS Finder GUI</b>, due to the + * large amount of meta files this OS attempts to write to the disk along with the new binaries. On + * this platform, firmwares must be copied to the disk via the Terminal application only to prevent + * firmware corruption. + * + * \section Sec_API User Application API + * + * Several user application functions for FLASH and other special memory area manipulations are exposed by the bootloader, + * allowing the user application to call into the bootloader at runtime to read and write FLASH data. + * + * By default, the bootloader API jump table is located 32 bytes from the end of the device's FLASH memory, and follows the + * following layout: + * + * \code + * #define BOOTLOADER_API_TABLE_SIZE 32 + * #define BOOTLOADER_API_TABLE_START ((FLASHEND + 1UL) - BOOTLOADER_API_TABLE_SIZE) + * #define BOOTLOADER_API_CALL(Index) (void*)((BOOTLOADER_API_TABLE_START + (Index * 2)) / 2) + * + * void (*BootloaderAPI_ErasePage)(uint32_t Address) = BOOTLOADER_API_CALL(0); + * void (*BootloaderAPI_WritePage)(uint32_t Address) = BOOTLOADER_API_CALL(1); + * void (*BootloaderAPI_FillWord)(uint32_t Address, uint16_t Word) = BOOTLOADER_API_CALL(2); + * uint8_t (*BootloaderAPI_ReadSignature)(uint16_t Address) = BOOTLOADER_API_CALL(3); + * uint8_t (*BootloaderAPI_ReadFuse)(uint16_t Address) = BOOTLOADER_API_CALL(4); + * uint8_t (*BootloaderAPI_ReadLock)(void) = BOOTLOADER_API_CALL(5); + * void (*BootloaderAPI_WriteLock)(uint8_t LockBits) = BOOTLOADER_API_CALL(6); + * + * #define BOOTLOADER_MAGIC_SIGNATURE_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 2)) + * #define BOOTLOADER_MAGIC_SIGNATURE 0xDCFB + * + * #define BOOTLOADER_CLASS_SIGNATURE_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 4)) + * #define BOOTLOADER_MASS_STORAGE_SIGNATURE 0xDF30 + * + * #define BOOTLOADER_ADDRESS_START (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 8)) + * #define BOOTLOADER_ADDRESS_LENGTH 4 + * \endcode + * + * From the application the API support of the bootloader can be detected by reading the FLASH memory bytes located at address + * \c BOOTLOADER_MAGIC_SIGNATURE_START and comparing them to the value \c BOOTLOADER_MAGIC_SIGNATURE. The class of bootloader + * can be determined by reading the FLASH memory bytes located at address \c BOOTLOADER_CLASS_SIGNATURE_START and comparing them + * to the value \c BOOTLOADER_MASS_STORAGE_SIGNATURE. The start address of the bootloader can be retrieved by reading the bytes + * of FLASH memory starting from address \c BOOTLOADER_ADDRESS_START. + * + * \subsection SSec_Aux_Space Auxiliary Bootloader Section + * To make the bootloader function on smaller devices (those with a physical bootloader section of smaller than 6KB) a second + * section of memory (called the <i>Auxiliary Bootloader Section</i>) is added before the start of the real bootloader section, + * and is filled with a portion of the bootloader code. This allows smaller devices to run the bootloader, at the cost of an + * additional portion of the device's FLASH (the bootloader section size in KB subtracted from the 6KB total size). A small + * trampoline is inserted at the start of the auxiliary section so that the bootloader will run normally in the case of a blank + * application section. + * + * On devices supporting a 8KB bootloader section size, the AUX section is not created in the final binary. + * + * \subsection SSec_API_MemLayout Device Memory Map + * The following illustration indicates the final memory map of the device when loaded with the bootloader. + * + * \verbatim + * +----------------------------+ 0x0000 + * | | + * | | + * | | + * | | + * | | + * | | + * | | + * | | + * | User Application | + * | | + * | | + * | | + * | | + * | | + * | | + * | | + * | | + * +----------------------------+ FLASHEND - BOOT_SECTION_SIZE - BOOT_AUX_SECTION_SIZE + * | Booloader Start Trampoline | + * | (Not User App. Accessible) | + * +----------------------------+ FLASHEND - BOOT_SECTION_SIZE - BOOT_AUX_SECTION_SIZE + 4 + * | | + * | Auxiliary Bootloader | + * | Space for Smaller Devices | + * | (Not User App. Accessible) | + * | | + * +----------------------------+ FLASHEND - BOOT_SECTION_SIZE + * | | + * | Bootloader Application | + * | (Not User App. Accessible) | + * | | + * +----------------------------+ FLASHEND - 96 + * | API Table Trampolines | + * | (Not User App. Accessible) | + * +----------------------------+ FLASHEND - 32 + * | Bootloader API Table | + * | (User App. Accessible) | + * +----------------------------+ FLASHEND - 8 + * | Bootloader ID Constants | + * | (User App. Accessible) | + * +----------------------------+ FLASHEND + * \endverbatim + * + * \section Sec_KnownIssues Known Issues: + * + * \par In some cases, the application is not fully loaded into the device. + * Write-caching on some operating systems may interfere with the normal + * operation of the bootloader. Write caching should be disabled when using the + * Mass Storage bootloader, or the file system synced via an appropriate command + * (such as the OS's normal disk ejection command) before disconnecting the device. + * + * \par After loading an application, it is not run automatically on startup. + * Some USB AVR boards ship with the BOOTRST fuse set, causing the bootloader + * to run automatically when the device is reset. In most cases, the BOOTRST + * fuse should be disabled and the HWBE fuse used instead to run the bootloader + * when needed. + * + * \section Sec_Options Project Options + * + * The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value. + * + * <table> + * <tr> + * <th><b>Define Name:</b></th> + * <th><b>Location:</b></th> + * <th><b>Description:</b></th> + * </tr> + * <tr> + * <td>NO_APP_START_ON_EJECT</td> + * <td>AppConfig.h</td> + * <td>Define to disable automatic start of the loaded application when the virtual + * Mass Storage disk is ejected on the host.</td> + * </tr> + * </table> + */ + |