diff options
Diffstat (limited to 'platforms')
43 files changed, 1574 insertions, 89 deletions
diff --git a/platforms/avr/drivers/backlight_pwm.c b/platforms/avr/drivers/backlight_pwm.c new file mode 100644 index 0000000000..d234115641 --- /dev/null +++ b/platforms/avr/drivers/backlight_pwm.c @@ -0,0 +1,463 @@ +#include "backlight.h" +#include "backlight_driver_common.h" +#include "progmem.h" +#include <avr/io.h> +#include <avr/interrupt.h> + +// Maximum duty cycle limit +#ifndef BACKLIGHT_LIMIT_VAL +# define BACKLIGHT_LIMIT_VAL 255 +#endif + +// This logic is a bit complex, we support 3 setups: +// +// 1. Hardware PWM when backlight is wired to a PWM pin. +// Depending on this pin, we use a different output compare unit. +// 2. Software PWM with hardware timers, but the used timer +// depends on the Audio setup (Audio wins over Backlight). +// 3. Full software PWM, driven by the matrix scan, if both timers are used by Audio. + +#if (defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB647__) || defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1287__) || defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)) && (BACKLIGHT_PIN == B5 || BACKLIGHT_PIN == B6 || BACKLIGHT_PIN == B7) +# define ICRx ICR1 +# define TCCRxA TCCR1A +# define TCCRxB TCCR1B +# define TIMERx_OVF_vect TIMER1_OVF_vect +# define TIMSKx TIMSK1 +# define TOIEx TOIE1 + +# if BACKLIGHT_PIN == B5 +# define COMxx0 COM1A0 +# define COMxx1 COM1A1 +# define OCRxx OCR1A +# elif BACKLIGHT_PIN == B6 +# define COMxx0 COM1B0 +# define COMxx1 COM1B1 +# define OCRxx OCR1B +# elif BACKLIGHT_PIN == B7 +# define COMxx0 COM1C0 +# define COMxx1 COM1C1 +# define OCRxx OCR1C +# endif +#elif (defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB647__) || defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1287__) || defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)) && (BACKLIGHT_PIN == C4 || BACKLIGHT_PIN == C5 || BACKLIGHT_PIN == C6) +# define ICRx ICR3 +# define TCCRxA TCCR3A +# define TCCRxB TCCR3B +# define TIMERx_OVF_vect TIMER3_OVF_vect +# define TIMSKx TIMSK3 +# define TOIEx TOIE3 + +# if BACKLIGHT_PIN == C4 +# if (defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)) +# error This MCU has no C4 pin! +# else +# define COMxx0 COM3C0 +# define COMxx1 COM3C1 +# define OCRxx OCR3C +# endif +# elif BACKLIGHT_PIN == C5 +# if (defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)) +# error This MCU has no C5 pin! +# else +# define COMxx0 COM3B0 +# define COMxx1 COM3B1 +# define OCRxx OCR3B +# endif +# elif BACKLIGHT_PIN == C6 +# define COMxx0 COM3A0 +# define COMxx1 COM3A1 +# define OCRxx OCR3A +# endif +#elif (defined(__AVR_AT90USB162__) || defined(__AVR_ATmega16U2__) || defined(__AVR_ATmega32U2__)) && (BACKLIGHT_PIN == B7 || BACKLIGHT_PIN == C5 || BACKLIGHT_PIN == C6) +# define ICRx ICR1 +# define TCCRxA TCCR1A +# define TCCRxB TCCR1B +# define TIMERx_OVF_vect TIMER1_OVF_vect +# define TIMSKx TIMSK1 +# define TOIEx TOIE1 + +# if BACKLIGHT_PIN == B7 +# define COMxx0 COM1C0 +# define COMxx1 COM1C1 +# define OCRxx OCR1C +# elif BACKLIGHT_PIN == C5 +# define COMxx0 COM1B0 +# define COMxx1 COM1B1 +# define OCRxx OCR1B +# elif BACKLIGHT_PIN == C6 +# define COMxx0 COM1A0 +# define COMxx1 COM1A1 +# define OCRxx OCR1A +# endif +#elif defined(__AVR_ATmega32A__) && (BACKLIGHT_PIN == D4 || BACKLIGHT_PIN == D5) +# define ICRx ICR1 +# define TCCRxA TCCR1A +# define TCCRxB TCCR1B +# define TIMERx_OVF_vect TIMER1_OVF_vect +# define TIMSKx TIMSK +# define TOIEx TOIE1 + +# if BACKLIGHT_PIN == D4 +# define COMxx0 COM1B0 +# define COMxx1 COM1B1 +# define OCRxx OCR1B +# elif BACKLIGHT_PIN == D5 +# define COMxx0 COM1A0 +# define COMxx1 COM1A1 +# define OCRxx OCR1A +# endif +#elif (defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328__)) && (BACKLIGHT_PIN == B1 || BACKLIGHT_PIN == B2) +# define ICRx ICR1 +# define TCCRxA TCCR1A +# define TCCRxB TCCR1B +# define TIMERx_OVF_vect TIMER1_OVF_vect +# define TIMSKx TIMSK1 +# define TOIEx TOIE1 + +# if BACKLIGHT_PIN == B1 +# define COMxx0 COM1A0 +# define COMxx1 COM1A1 +# define OCRxx OCR1A +# elif BACKLIGHT_PIN == B2 +# define COMxx0 COM1B0 +# define COMxx1 COM1B1 +# define OCRxx OCR1B +# endif +#elif (AUDIO_PIN != B5) && (AUDIO_PIN != B6) && (AUDIO_PIN != B7) && (AUDIO_PIN_ALT != B5) && (AUDIO_PIN_ALT != B6) && (AUDIO_PIN_ALT != B7) +// Timer 1 is not in use by Audio feature, Backlight can use it +# pragma message "Using hardware timer 1 with software PWM" +# define BACKLIGHT_PWM_TIMER +# define ICRx ICR1 +# define TCCRxA TCCR1A +# define TCCRxB TCCR1B +# define TIMERx_COMPA_vect TIMER1_COMPA_vect +# define TIMERx_OVF_vect TIMER1_OVF_vect +# if defined(__AVR_ATmega32A__) // This MCU has only one TIMSK register +# define TIMSKx TIMSK +# else +# define TIMSKx TIMSK1 +# endif +# define TOIEx TOIE1 + +# define OCIExA OCIE1A +# define OCRxx OCR1A +#elif (AUDIO_PIN != C4) && (AUDIO_PIN != C5) && (AUDIO_PIN != C6) +# pragma message "Using hardware timer 3 with software PWM" +// Timer 3 is not in use by Audio feature, Backlight can use it +# define BACKLIGHT_PWM_TIMER +# define ICRx ICR1 +# define TCCRxA TCCR3A +# define TCCRxB TCCR3B +# define TIMERx_COMPA_vect TIMER3_COMPA_vect +# define TIMERx_OVF_vect TIMER3_OVF_vect +# define TIMSKx TIMSK3 +# define TOIEx TOIE3 + +# define OCIExA OCIE3A +# define OCRxx OCR3A +#endif + +#ifndef BACKLIGHT_PWM_TIMER // pwm through software + +static inline void enable_pwm(void) { +# if BACKLIGHT_ON_STATE == 1 + TCCRxA |= _BV(COMxx1); +# else + TCCRxA |= _BV(COMxx1) | _BV(COMxx0); +# endif +} + +static inline void disable_pwm(void) { +# if BACKLIGHT_ON_STATE == 1 + TCCRxA &= ~(_BV(COMxx1)); +# else + TCCRxA &= ~(_BV(COMxx1) | _BV(COMxx0)); +# endif +} + +#endif + +#ifdef BACKLIGHT_PWM_TIMER + +// The idea of software PWM assisted by hardware timers is the following +// we use the hardware timer in fast PWM mode like for hardware PWM, but +// instead of letting the Output Match Comparator control the led pin +// (which is not possible since the backlight is not wired to PWM pins on the +// CPU), we do the LED on/off by oursleves. +// The timer is setup to count up to 0xFFFF, and we set the Output Compare +// register to the current 16bits backlight level (after CIE correction). +// This means the CPU will trigger a compare match interrupt when the counter +// reaches the backlight level, where we turn off the LEDs, +// but also an overflow interrupt when the counter rolls back to 0, +// in which we're going to turn on the LEDs. +// The LED will then be on for OCRxx/0xFFFF time, adjusted every 244Hz, +// or F_CPU/BACKLIGHT_CUSTOM_RESOLUTION if used. + +// Triggered when the counter reaches the OCRx value +ISR(TIMERx_COMPA_vect) { + backlight_pins_off(); +} + +// Triggered when the counter reaches the TOP value +// this one triggers at F_CPU/ICRx = 16MHz/65536 =~ 244 Hz +ISR(TIMERx_OVF_vect) { +# ifdef BACKLIGHT_BREATHING + if (is_breathing()) { + breathing_task(); + } +# endif + // for very small values of OCRxx (or backlight level) + // we can't guarantee this whole code won't execute + // at the same time as the compare match interrupt + // which means that we might turn on the leds while + // trying to turn them off, leading to flickering + // artifacts (especially while breathing, because breathing_task + // takes many computation cycles). + // so better not turn them on while the counter TOP is very low. + if (OCRxx > ICRx / 250 + 5) { + backlight_pins_on(); + } +} + +#endif + +#define TIMER_TOP 0xFFFFU + +// See http://jared.geek.nz/2013/feb/linear-led-pwm +static uint16_t cie_lightness(uint16_t v) { + if (v <= (uint32_t)ICRx / 12) // If the value is less than or equal to ~8% of max + { + return v / 9; // Same as dividing by 900% + } else { + // In the next two lines values are bit-shifted. This is to avoid loosing decimals in integer math. + uint32_t y = (((uint32_t)v + (uint32_t)ICRx / 6) << 5) / ((uint32_t)ICRx / 6 + ICRx); // If above 8%, add ~16% of max, and normalize with (max + ~16% max) + uint32_t out = (y * y * y * ICRx) >> 15; // Cube it and undo the bit-shifting. (which is now three times as much due to the cubing) + + if (out > ICRx) // Avoid overflows + { + out = ICRx; + } + return (uint16_t)out; + } +} + +// rescale the supplied backlight value to be in terms of the value limit // range for val is [0..ICRx]. PWM pin is high while the timer count is below val. +static uint32_t rescale_limit_val(uint32_t val) { + return (val * (BACKLIGHT_LIMIT_VAL + 1)) / 256; +} + +// range for val is [0..ICRx]. PWM pin is high while the timer count is below val. +static inline void set_pwm(uint16_t val) { + OCRxx = val; +} + +void backlight_set(uint8_t level) { + if (level > BACKLIGHT_LEVELS) level = BACKLIGHT_LEVELS; + + if (level == 0) { +#ifdef BACKLIGHT_PWM_TIMER + if (OCRxx) { + TIMSKx &= ~(_BV(OCIExA)); + TIMSKx &= ~(_BV(TOIEx)); + } +#else + // Turn off PWM control on backlight pin + disable_pwm(); +#endif + backlight_pins_off(); + } else { +#ifdef BACKLIGHT_PWM_TIMER + if (!OCRxx) { + TIMSKx |= _BV(OCIExA); + TIMSKx |= _BV(TOIEx); + } +#else + // Turn on PWM control of backlight pin + enable_pwm(); +#endif + } + // Set the brightness + set_pwm(cie_lightness(rescale_limit_val(ICRx * (uint32_t)level / BACKLIGHT_LEVELS))); +} + +void backlight_task(void) {} + +#ifdef BACKLIGHT_BREATHING + +# define BREATHING_NO_HALT 0 +# define BREATHING_HALT_OFF 1 +# define BREATHING_HALT_ON 2 +# define BREATHING_STEPS 128 + +static uint8_t breathing_halt = BREATHING_NO_HALT; +static uint16_t breathing_counter = 0; + +static uint8_t breath_scale_counter = 1; +/* Run the breathing loop at ~120Hz*/ +const uint8_t breathing_ISR_frequency = 120; +static uint16_t breathing_freq_scale_factor = 2; + +# ifdef BACKLIGHT_PWM_TIMER +static bool breathing = false; + +bool is_breathing(void) { + return breathing; +} + +# define breathing_interrupt_enable() \ + do { \ + breathing = true; \ + } while (0) +# define breathing_interrupt_disable() \ + do { \ + breathing = false; \ + } while (0) +# else + +bool is_breathing(void) { + return !!(TIMSKx & _BV(TOIEx)); +} + +# define breathing_interrupt_enable() \ + do { \ + TIMSKx |= _BV(TOIEx); \ + } while (0) +# define breathing_interrupt_disable() \ + do { \ + TIMSKx &= ~_BV(TOIEx); \ + } while (0) +# endif + +# define breathing_min() \ + do { \ + breathing_counter = 0; \ + } while (0) +# define breathing_max() \ + do { \ + breathing_counter = get_breathing_period() * breathing_ISR_frequency / 2; \ + } while (0) + +void breathing_enable(void) { + breathing_counter = 0; + breathing_halt = BREATHING_NO_HALT; + breathing_interrupt_enable(); +} + +void breathing_pulse(void) { + if (get_backlight_level() == 0) + breathing_min(); + else + breathing_max(); + breathing_halt = BREATHING_HALT_ON; + breathing_interrupt_enable(); +} + +void breathing_disable(void) { + breathing_interrupt_disable(); + // Restore backlight level + backlight_set(get_backlight_level()); +} + +void breathing_self_disable(void) { + if (get_backlight_level() == 0) + breathing_halt = BREATHING_HALT_OFF; + else + breathing_halt = BREATHING_HALT_ON; +} + +/* To generate breathing curve in python: + * from math import sin, pi; [int(sin(x/128.0*pi)**4*255) for x in range(128)] + */ +static const uint8_t breathing_table[BREATHING_STEPS] PROGMEM = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 3, 4, 5, 6, 8, 10, 12, 15, 17, 20, 24, 28, 32, 36, 41, 46, 51, 57, 63, 70, 76, 83, 91, 98, 106, 113, 121, 129, 138, 146, 154, 162, 170, 178, 185, 193, 200, 207, 213, 220, 225, 231, 235, 240, 244, 247, 250, 252, 253, 254, 255, 254, 253, 252, 250, 247, 244, 240, 235, 231, 225, 220, 213, 207, 200, 193, 185, 178, 170, 162, 154, 146, 138, 129, 121, 113, 106, 98, 91, 83, 76, 70, 63, 57, 51, 46, 41, 36, 32, 28, 24, 20, 17, 15, 12, 10, 8, 6, 5, 4, 3, 2, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; + +// Use this before the cie_lightness function. +static inline uint16_t scale_backlight(uint16_t v) { + return v / BACKLIGHT_LEVELS * get_backlight_level(); +} + +# ifdef BACKLIGHT_PWM_TIMER +void breathing_task(void) +# else +/* Assuming a 16MHz CPU clock and a timer that resets at 64k (ICR1), the following interrupt handler will run + * about 244 times per second. + * + * The following ISR runs at F_CPU/ISRx. With a 16MHz clock and default pwm resolution, that means 244Hz + */ +ISR(TIMERx_OVF_vect) +# endif +{ + + // Only run this ISR at ~120 Hz + if (breath_scale_counter++ == breathing_freq_scale_factor) { + breath_scale_counter = 1; + } else { + return; + } + uint16_t interval = (uint16_t)get_breathing_period() * breathing_ISR_frequency / BREATHING_STEPS; + // resetting after one period to prevent ugly reset at overflow. + breathing_counter = (breathing_counter + 1) % (get_breathing_period() * breathing_ISR_frequency); + uint8_t index = breathing_counter / interval; + // limit index to max step value + if (index >= BREATHING_STEPS) { + index = BREATHING_STEPS - 1; + } + + if (((breathing_halt == BREATHING_HALT_ON) && (index == BREATHING_STEPS / 2)) || ((breathing_halt == BREATHING_HALT_OFF) && (index == BREATHING_STEPS - 1))) { + breathing_interrupt_disable(); + } + + // Set PWM to a brightnessvalue scaled to the configured resolution + set_pwm(cie_lightness(rescale_limit_val(scale_backlight((uint32_t)pgm_read_byte(&breathing_table[index]) * ICRx / 255)))); +} + +#endif // BACKLIGHT_BREATHING + +void backlight_init_ports(void) { + // Setup backlight pin as output and output to on state. + backlight_pins_init(); + + // I could write a wall of text here to explain... but TL;DW + // Go read the ATmega32u4 datasheet. + // And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on + +#ifdef BACKLIGHT_PWM_TIMER + // TimerX setup, Fast PWM mode count to TOP set in ICRx + TCCRxA = _BV(WGM11); // = 0b00000010; + // clock select clk/1 + TCCRxB = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001; +#else // hardware PWM + // Pin PB7 = OCR1C (Timer 1, Channel C) + // Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0 + // (i.e. start high, go low when counter matches.) + // WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0 + // Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1 + + /* + 14.8.3: + "In fast PWM mode, the compare units allow generation of PWM waveforms on the OCnx pins. Setting the COMnx1:0 bits to two will produce a non-inverted PWM [..]." + "In fast PWM mode the counter is incremented until the counter value matches either one of the fixed values 0x00FF, 0x01FF, or 0x03FF (WGMn3:0 = 5, 6, or 7), the value in ICRn (WGMn3:0 = 14), or the value in OCRnA (WGMn3:0 = 15)." + */ + TCCRxA = _BV(COMxx1) | _BV(WGM11); // = 0b00001010; + TCCRxB = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001; +#endif + +#ifdef BACKLIGHT_CUSTOM_RESOLUTION +# if (BACKLIGHT_CUSTOM_RESOLUTION > 0xFFFF || BACKLIGHT_CUSTOM_RESOLUTION < 1) +# error "This out of range of the timer capabilities" +# elif (BACKLIGHT_CUSTOM_RESOLUTION < 0xFF) +# warning "Resolution lower than 0xFF isn't recommended" +# endif +# ifdef BACKLIGHT_BREATHING + breathing_freq_scale_factor = F_CPU / BACKLIGHT_CUSTOM_RESOLUTION / 120; +# endif + ICRx = BACKLIGHT_CUSTOM_RESOLUTION; +#else + ICRx = TIMER_TOP; +#endif + + backlight_init(); +#ifdef BACKLIGHT_BREATHING + if (is_backlight_breathing()) { + breathing_enable(); + } +#endif +} diff --git a/platforms/avr/sleep_led.c b/platforms/avr/sleep_led.c index b05431633b..ad6253be93 100644 --- a/platforms/avr/sleep_led.c +++ b/platforms/avr/sleep_led.c @@ -109,16 +109,19 @@ ISR(TIMERx_COMPA_vect) { uint8_t duration : 2; uint8_t index : 6; } pwm; - } timer = {.row = 0}; + } timer = {.row = 0}; + static led_t led_state = {0}; timer.row++; // LED on if (timer.pwm.count == 0) { - led_set(1 << USB_LED_CAPS_LOCK); + led_state.caps_lock = true; + led_set(led_state.raw); } // LED off if (timer.pwm.count == pgm_read_byte(&breathing_table[timer.pwm.index])) { - led_set(0); + led_state.caps_lock = false; + led_set(led_state.raw); } } diff --git a/platforms/chibios/boards/GENERIC_PROMICRO_RP2040/configs/mcuconf.h b/platforms/chibios/boards/GENERIC_PROMICRO_RP2040/configs/mcuconf.h index ab293c0b40..8621807cbb 100644 --- a/platforms/chibios/boards/GENERIC_PROMICRO_RP2040/configs/mcuconf.h +++ b/platforms/chibios/boards/GENERIC_PROMICRO_RP2040/configs/mcuconf.h @@ -106,7 +106,6 @@ #define RP_USB_USE_USBD0 TRUE #define RP_USB_FORCE_VBUS_DETECT TRUE #define RP_USE_EXTERNAL_VBUS_DETECT FALSE -#define RP_USB_USE_SOF_INTR TRUE #define RP_USB_USE_ERROR_DATA_SEQ_INTR FALSE #endif /* MCUCONF_H */ diff --git a/platforms/chibios/boards/GENERIC_RP_RP2040/configs/mcuconf.h b/platforms/chibios/boards/GENERIC_RP_RP2040/configs/mcuconf.h index b91d762419..902f9b5005 100644 --- a/platforms/chibios/boards/GENERIC_RP_RP2040/configs/mcuconf.h +++ b/platforms/chibios/boards/GENERIC_RP_RP2040/configs/mcuconf.h @@ -106,7 +106,6 @@ #define RP_USB_USE_USBD0 TRUE #define RP_USB_FORCE_VBUS_DETECT TRUE #define RP_USE_EXTERNAL_VBUS_DETECT FALSE -#define RP_USB_USE_SOF_INTR TRUE #define RP_USB_USE_ERROR_DATA_SEQ_INTR FALSE #endif /* MCUCONF_H */ diff --git a/platforms/chibios/boards/PJRC_TEENSY_3_5/board/board.mk b/platforms/chibios/boards/GENERIC_STM32_H723XG/board/board.mk index e129836b08..3511f752a9 100644 --- a/platforms/chibios/boards/PJRC_TEENSY_3_5/board/board.mk +++ b/platforms/chibios/boards/GENERIC_STM32_H723XG/board/board.mk @@ -1,10 +1,11 @@ -include $(CHIBIOS_CONTRIB)/os/hal/boards/PJRC_TEENSY_3_5/board.mk - # List of all the board related files. +BOARDSRC = $(CHIBIOS)/os/hal/boards/ST_NUCLEO144_H723ZG/board.c + +# Extra files BOARDSRC += $(BOARD_PATH)/board/extra.c # Required include directories -BOARDINC += $(BOARD_PATH)/board +BOARDINC = $(CHIBIOS)/os/hal/boards/ST_NUCLEO144_H723ZG # Shared variables ALLCSRC += $(BOARDSRC) diff --git a/platforms/chibios/boards/GENERIC_STM32_H723XG/board/extra.c b/platforms/chibios/boards/GENERIC_STM32_H723XG/board/extra.c new file mode 100755 index 0000000000..fce0b4abad --- /dev/null +++ b/platforms/chibios/boards/GENERIC_STM32_H723XG/board/extra.c @@ -0,0 +1,36 @@ +// Copyright 2023 Nick Brassel (@tzarc) +// SPDX-License-Identifier: GPL-2.0-or-later +#include <hal.h> +#define BOOTLOADER_MAGIC 0xDEADBEEF + +//////////////////////////////////////////////////////////////////////////////// +// Different signalling for bootloader entry +// - RAM is cleared on reset, so we can't use the usual __ram0_end__ symbol. +// - Use backup registers in the RTC peripheral to store the magic value instead. + +static inline void enable_backup_register_access(void) { + PWR->CR1 |= PWR_CR1_DBP; +} + +static inline void disable_backup_register_access(void) { + PWR->CR1 &= ~PWR_CR1_DBP; +} + +void bootloader_marker_enable(void) { + enable_backup_register_access(); + RTC->BKP0R = BOOTLOADER_MAGIC; + disable_backup_register_access(); +} + +bool bootloader_marker_active(void) { + enable_backup_register_access(); + bool ret = RTC->BKP0R == BOOTLOADER_MAGIC; + disable_backup_register_access(); + return ret; +} + +void bootloader_marker_disable(void) { + enable_backup_register_access(); + RTC->BKP0R = 0; + disable_backup_register_access(); +} diff --git a/platforms/chibios/boards/GENERIC_STM32_H723XG/configs/config.h b/platforms/chibios/boards/GENERIC_STM32_H723XG/configs/config.h new file mode 100644 index 0000000000..f43df29b54 --- /dev/null +++ b/platforms/chibios/boards/GENERIC_STM32_H723XG/configs/config.h @@ -0,0 +1,9 @@ +// Copyright 2023 Nick Brassel (@tzarc) +// SPDX-License-Identifier: GPL-2.0-or-later +#pragma once + +#define USB_DRIVER USBD2 + +#ifndef EARLY_INIT_PERFORM_BOOTLOADER_JUMP +# define EARLY_INIT_PERFORM_BOOTLOADER_JUMP TRUE +#endif diff --git a/platforms/chibios/boards/GENERIC_STM32_H723XG/configs/mcuconf.h b/platforms/chibios/boards/GENERIC_STM32_H723XG/configs/mcuconf.h new file mode 100644 index 0000000000..0239ec5273 --- /dev/null +++ b/platforms/chibios/boards/GENERIC_STM32_H723XG/configs/mcuconf.h @@ -0,0 +1,511 @@ +/* + ChibiOS - Copyright (C) 2006..2020 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef MCUCONF_H +#define MCUCONF_H + +/* + * STM32H723/33/25/35 drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 15...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +#define STM32H7xx_MCUCONF +#define STM32H723_MCUCONF +#define STM32H733_MCUCONF +#define STM32H725_MCUCONF +#define STM32H735_MCUCONF + +/* + * General settings. + */ +#define STM32_NO_INIT FALSE + +/* + * Memory attributes settings. + */ +#define STM32_NOCACHE_ENABLE FALSE +#define STM32_NOCACHE_MPU_REGION MPU_REGION_6 +#define STM32_NOCACHE_RBAR 0x24000000U +#define STM32_NOCACHE_RASR MPU_RASR_SIZE_16K + +/* + * PWR system settings. + * Reading STM32 Reference Manual is required, settings in PWR_CR3 are + * very critical. + * Register constants are taken from the ST header. + */ +#define STM32_VOS STM32_VOS_SCALE0 +#define STM32_PWR_CR1 (PWR_CR1_SVOS_1 | PWR_CR1_SVOS_0) +#define STM32_PWR_CR2 (PWR_CR2_BREN) +#define STM32_PWR_CR3 (PWR_CR3_LDOEN | PWR_CR3_USB33DEN) +#define STM32_PWR_CPUCR 0 + +/* + * Clock tree static settings. + * Reading STM32 Reference Manual is required. + */ +#define STM32_HSI_ENABLED TRUE +#define STM32_LSI_ENABLED FALSE +#define STM32_CSI_ENABLED FALSE +#define STM32_HSI48_ENABLED TRUE +#define STM32_HSE_ENABLED TRUE +#define STM32_LSE_ENABLED FALSE +#define STM32_HSIDIV STM32_HSIDIV_DIV1 + +/* + * PLLs static settings. + * Reading STM32 Reference Manual is required. + */ +#define STM32_PLLSRC STM32_PLLSRC_HSE_CK +#define STM32_PLLCFGR_MASK ~0 +#define STM32_PLL1_ENABLED TRUE +#define STM32_PLL1_P_ENABLED TRUE +#define STM32_PLL1_Q_ENABLED TRUE +#define STM32_PLL1_R_ENABLED TRUE +#define STM32_PLL1_DIVM_VALUE 4 +#define STM32_PLL1_DIVN_VALUE 275 +#define STM32_PLL1_FRACN_VALUE 0 +#define STM32_PLL1_DIVP_VALUE 1 +#define STM32_PLL1_DIVQ_VALUE 10 +#define STM32_PLL1_DIVR_VALUE 4 +#define STM32_PLL2_ENABLED TRUE +#define STM32_PLL2_P_ENABLED TRUE +#define STM32_PLL2_Q_ENABLED TRUE +#define STM32_PLL2_R_ENABLED TRUE +#define STM32_PLL2_DIVM_VALUE 4 +#define STM32_PLL2_DIVN_VALUE 400 +#define STM32_PLL2_FRACN_VALUE 0 +#define STM32_PLL2_DIVP_VALUE 40 +#define STM32_PLL2_DIVQ_VALUE 8 +#define STM32_PLL2_DIVR_VALUE 8 +#define STM32_PLL3_ENABLED TRUE +#define STM32_PLL3_P_ENABLED TRUE +#define STM32_PLL3_Q_ENABLED TRUE +#define STM32_PLL3_R_ENABLED TRUE +#define STM32_PLL3_DIVM_VALUE 4 +#define STM32_PLL3_DIVN_VALUE 240 +#define STM32_PLL3_FRACN_VALUE 0 +#define STM32_PLL3_DIVP_VALUE 10 +#define STM32_PLL3_DIVQ_VALUE 10 +#define STM32_PLL3_DIVR_VALUE 10 + +/* + * Core clocks dynamic settings (can be changed at runtime). + * Reading STM32 Reference Manual is required. + */ +#define STM32_SW STM32_SW_PLL1_P_CK +#define STM32_RTCSEL STM32_RTCSEL_LSI_CK +#define STM32_D1CPRE STM32_D1CPRE_DIV1 +#define STM32_D1HPRE STM32_D1HPRE_DIV2 +#define STM32_D1PPRE3 STM32_D1PPRE3_DIV2 +#define STM32_D2PPRE1 STM32_D2PPRE1_DIV2 +#define STM32_D2PPRE2 STM32_D2PPRE2_DIV2 +#define STM32_D3PPRE4 STM32_D3PPRE4_DIV2 + +/* + * Peripherals clocks static settings. + * Reading STM32 Reference Manual is required. + */ +#define STM32_MCO1SEL STM32_MCO1SEL_HSI_CK +#define STM32_MCO1PRE_VALUE 4 +#define STM32_MCO2SEL STM32_MCO2SEL_SYS_CK +#define STM32_MCO2PRE_VALUE 4 +#define STM32_TIMPRE_ENABLE TRUE +#define STM32_HRTIMSEL 0 +#define STM32_STOPKERWUCK 0 +#define STM32_STOPWUCK 0 +#define STM32_RTCPRE_VALUE 8 +#define STM32_CKPERSEL STM32_CKPERSEL_HSE_CK +#define STM32_SDMMCSEL STM32_SDMMCSEL_PLL1_Q_CK +#define STM32_OCTOSPISEL STM32_OCTOSPISEL_HCLK +#define STM32_FMCSEL STM32_FMCSEL_HCLK +#define STM32_SWPSEL STM32_SWPSEL_PCLK1 +#define STM32_FDCANSEL STM32_FDCANSEL_HSE_CK +#define STM32_DFSDM1SEL STM32_DFSDM1SEL_PCLK2 +#define STM32_SPDIFSEL STM32_SPDIFSEL_PLL1_Q_CK +#define STM32_SPI45SEL STM32_SPI45SEL_PCLK2 +#define STM32_SPI123SEL STM32_SPI123SEL_PLL1_Q_CK +#define STM32_SAI1SEL STM32_SAI1SEL_PLL1_Q_CK +#define STM32_LPTIM1SEL STM32_LPTIM1SEL_PCLK1 +#define STM32_CECSEL STM32_CECSEL_LSE_CK +#define STM32_USBSEL STM32_USBSEL_PLL3_Q_CK +#define STM32_I2C1235SEL STM32_I2C1235SEL_PCLK1 +#define STM32_RNGSEL STM32_RNGSEL_PLL1_Q_CK +#define STM32_USART16910SEL STM32_USART16910SEL_PCLK2 +#define STM32_USART234578SEL STM32_USART234578SEL_PCLK1 +#define STM32_SPI6SEL STM32_SPI6SEL_PCLK4 +#define STM32_SAI4BSEL STM32_SAI4BSEL_PLL1_Q_CK +#define STM32_SAI4ASEL STM32_SAI4ASEL_PLL1_Q_CK +#define STM32_ADCSEL STM32_ADCSEL_PLL2_P_CK +#define STM32_LPTIM345SEL STM32_LPTIM345SEL_PCLK4 +#define STM32_LPTIM2SEL STM32_LPTIM2SEL_PCLK4 +#define STM32_I2C4SEL STM32_I2C4SEL_PCLK4 +#define STM32_LPUART1SEL STM32_LPUART1SEL_PCLK4 + +/* + * IRQ system settings. + */ +#define STM32_IRQ_EXTI0_PRIORITY 6 +#define STM32_IRQ_EXTI1_PRIORITY 6 +#define STM32_IRQ_EXTI2_PRIORITY 6 +#define STM32_IRQ_EXTI3_PRIORITY 6 +#define STM32_IRQ_EXTI4_PRIORITY 6 +#define STM32_IRQ_EXTI5_9_PRIORITY 6 +#define STM32_IRQ_EXTI10_15_PRIORITY 6 +#define STM32_IRQ_EXTI16_PRIORITY 6 +#define STM32_IRQ_EXTI17_PRIORITY 6 +#define STM32_IRQ_EXTI18_PRIORITY 6 +#define STM32_IRQ_EXTI19_PRIORITY 6 +#define STM32_IRQ_EXTI20_21_PRIORITY 6 + +#define STM32_IRQ_FDCAN1_PRIORITY 10 +#define STM32_IRQ_FDCAN2_PRIORITY 10 + +#define STM32_IRQ_MDMA_PRIORITY 9 + +#define STM32_IRQ_OCTOSPI1_PRIORITY 10 +#define STM32_IRQ_OCTOSPI2_PRIORITY 10 + +#define STM32_IRQ_SDMMC1_PRIORITY 9 +#define STM32_IRQ_SDMMC2_PRIORITY 9 + +#define STM32_IRQ_TIM1_UP_PRIORITY 7 +#define STM32_IRQ_TIM1_CC_PRIORITY 7 +#define STM32_IRQ_TIM2_PRIORITY 7 +#define STM32_IRQ_TIM3_PRIORITY 7 +#define STM32_IRQ_TIM4_PRIORITY 7 +#define STM32_IRQ_TIM5_PRIORITY 7 +#define STM32_IRQ_TIM6_PRIORITY 7 +#define STM32_IRQ_TIM7_PRIORITY 7 +#define STM32_IRQ_TIM8_BRK_TIM12_PRIORITY 7 +#define STM32_IRQ_TIM8_UP_TIM13_PRIORITY 7 +#define STM32_IRQ_TIM8_TRGCO_TIM14_PRIORITY 7 +#define STM32_IRQ_TIM8_CC_PRIORITY 7 +#define STM32_IRQ_TIM15_PRIORITY 7 +#define STM32_IRQ_TIM16_PRIORITY 7 +#define STM32_IRQ_TIM17_PRIORITY 7 + +#define STM32_IRQ_USART1_PRIORITY 12 +#define STM32_IRQ_USART2_PRIORITY 12 +#define STM32_IRQ_USART3_PRIORITY 12 +#define STM32_IRQ_UART4_PRIORITY 12 +#define STM32_IRQ_UART5_PRIORITY 12 +#define STM32_IRQ_USART6_PRIORITY 12 +#define STM32_IRQ_UART7_PRIORITY 12 +#define STM32_IRQ_UART8_PRIORITY 12 +#define STM32_IRQ_UART9_PRIORITY 12 +#define STM32_IRQ_USART10_PRIORITY 12 +#define STM32_IRQ_LPUART1_PRIORITY 12 + +/* + * ADC driver system settings. + */ +#define STM32_ADC_DUAL_MODE FALSE +#define STM32_ADC_SAMPLES_SIZE 16 +#define STM32_ADC_USE_ADC12 FALSE +#define STM32_ADC_ADC12_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_ADC_ADC12_DMA_PRIORITY 2 +#define STM32_ADC_ADC12_IRQ_PRIORITY 5 +#define STM32_ADC_ADC12_CLOCK_MODE ADC_CCR_CKMODE_AHB_DIV4 + +/* + * CAN driver system settings. + */ +#define STM32_CAN_USE_FDCAN1 FALSE +#define STM32_CAN_USE_FDCAN2 FALSE + +/* + * DAC driver system settings. + */ +#define STM32_DAC_DUAL_MODE FALSE +#define STM32_DAC_USE_DAC1_CH1 FALSE +#define STM32_DAC_USE_DAC1_CH2 FALSE +#define STM32_DAC_DAC1_CH1_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH2_IRQ_PRIORITY 10 +#define STM32_DAC_DAC1_CH1_DMA_PRIORITY 2 +#define STM32_DAC_DAC1_CH2_DMA_PRIORITY 2 +#define STM32_DAC_DAC1_CH1_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_DAC_DAC1_CH2_DMA_STREAM STM32_DMA_STREAM_ID_ANY + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM4 FALSE +#define STM32_GPT_USE_TIM5 FALSE +#define STM32_GPT_USE_TIM6 FALSE +#define STM32_GPT_USE_TIM7 FALSE +#define STM32_GPT_USE_TIM8 FALSE +#define STM32_GPT_USE_TIM12 FALSE +#define STM32_GPT_USE_TIM13 FALSE +#define STM32_GPT_USE_TIM14 FALSE +#define STM32_GPT_USE_TIM15 FALSE +#define STM32_GPT_USE_TIM16 FALSE +#define STM32_GPT_USE_TIM17 FALSE + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_USE_I2C3 FALSE +#define STM32_I2C_USE_I2C4 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_I2C_I2C1_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_I2C_I2C2_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_I2C_I2C2_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_I2C_I2C3_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_I2C_I2C3_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_I2C_I2C4_RX_BDMA_STREAM STM32_BDMA_STREAM_ID_ANY +#define STM32_I2C_I2C4_TX_BDMA_STREAM STM32_BDMA_STREAM_ID_ANY +#define STM32_I2C_I2C1_IRQ_PRIORITY 5 +#define STM32_I2C_I2C2_IRQ_PRIORITY 5 +#define STM32_I2C_I2C3_IRQ_PRIORITY 5 +#define STM32_I2C_I2C4_IRQ_PRIORITY 5 +#define STM32_I2C_I2C1_DMA_PRIORITY 3 +#define STM32_I2C_I2C2_DMA_PRIORITY 3 +#define STM32_I2C_I2C3_DMA_PRIORITY 3 +#define STM32_I2C_I2C4_DMA_PRIORITY 3 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_USE_TIM4 FALSE +#define STM32_ICU_USE_TIM5 FALSE +#define STM32_ICU_USE_TIM8 FALSE +#define STM32_ICU_USE_TIM12 FALSE +#define STM32_ICU_USE_TIM13 FALSE +#define STM32_ICU_USE_TIM14 FALSE +#define STM32_ICU_USE_TIM15 FALSE +#define STM32_ICU_USE_TIM16 FALSE +#define STM32_ICU_USE_TIM17 FALSE + +/* + * MAC driver system settings. + */ +#define STM32_MAC_TRANSMIT_BUFFERS 2 +#define STM32_MAC_RECEIVE_BUFFERS 4 +#define STM32_MAC_BUFFERS_SIZE 1522 +#define STM32_MAC_PHY_TIMEOUT 100 +#define STM32_MAC_ETH1_CHANGE_PHY_STATE TRUE +#define STM32_MAC_ETH1_IRQ_PRIORITY 13 +#define STM32_MAC_IP_CHECKSUM_OFFLOAD 0 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_USE_TIM4 FALSE +#define STM32_PWM_USE_TIM5 FALSE +#define STM32_PWM_USE_TIM8 FALSE +#define STM32_PWM_USE_TIM12 FALSE +#define STM32_PWM_USE_TIM13 FALSE +#define STM32_PWM_USE_TIM14 FALSE +#define STM32_PWM_USE_TIM15 FALSE +#define STM32_PWM_USE_TIM16 FALSE +#define STM32_PWM_USE_TIM17 FALSE + +/* + * RTC driver system settings. + */ +#define STM32_RTC_PRESA_VALUE 32 +#define STM32_RTC_PRESS_VALUE 1024 +#define STM32_RTC_CR_INIT 0 +#define STM32_RTC_TAMPCR_INIT 0 + +/* + * SDC driver system settings. + */ +#define STM32_SDC_USE_SDMMC1 FALSE +#define STM32_SDC_USE_SDMMC2 FALSE +#define STM32_SDC_SDMMC_UNALIGNED_SUPPORT TRUE +#define STM32_SDC_SDMMC_WRITE_TIMEOUT 10000 +#define STM32_SDC_SDMMC_READ_TIMEOUT 10000 +#define STM32_SDC_SDMMC_CLOCK_DELAY 10 +#define STM32_SDC_SDMMC_PWRSAV TRUE + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 FALSE +#define STM32_SERIAL_USE_USART3 FALSE +#define STM32_SERIAL_USE_UART4 FALSE +#define STM32_SERIAL_USE_UART5 FALSE +#define STM32_SERIAL_USE_USART6 FALSE +#define STM32_SERIAL_USE_UART7 FALSE +#define STM32_SERIAL_USE_UART8 FALSE +#define STM32_SERIAL_USE_UART9 FALSE +#define STM32_SERIAL_USE_USART10 FALSE +#define STM32_SERIAL_USE_LPUART1 FALSE + +/* + * SIO driver system settings. + */ +#define STM32_SIO_USE_USART1 FALSE +#define STM32_SIO_USE_USART2 FALSE +#define STM32_SIO_USE_USART3 FALSE +#define STM32_SIO_USE_UART4 FALSE +#define STM32_SIO_USE_UART5 FALSE +#define STM32_SIO_USE_USART6 FALSE +#define STM32_SIO_USE_UART7 FALSE +#define STM32_SIO_USE_UART8 FALSE +#define STM32_SIO_USE_UART9 FALSE +#define STM32_SIO_USE_USART10 FALSE +#define STM32_SIO_USE_LPUART1 FALSE + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 FALSE +#define STM32_SPI_USE_SPI3 FALSE +#define STM32_SPI_USE_SPI4 FALSE +#define STM32_SPI_USE_SPI5 FALSE +#define STM32_SPI_USE_SPI6 FALSE +#define STM32_SPI_SPI1_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI1_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI2_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI2_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI3_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI3_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI4_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI4_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI5_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI5_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_SPI_SPI6_RX_BDMA_STREAM STM32_BDMA_STREAM_ID_ANY +#define STM32_SPI_SPI6_TX_BDMA_STREAM STM32_BDMA_STREAM_ID_ANY +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI3_DMA_PRIORITY 1 +#define STM32_SPI_SPI4_DMA_PRIORITY 1 +#define STM32_SPI_SPI5_DMA_PRIORITY 1 +#define STM32_SPI_SPI6_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 10 +#define STM32_SPI_SPI2_IRQ_PRIORITY 10 +#define STM32_SPI_SPI3_IRQ_PRIORITY 10 +#define STM32_SPI_SPI4_IRQ_PRIORITY 10 +#define STM32_SPI_SPI5_IRQ_PRIORITY 10 +#define STM32_SPI_SPI6_IRQ_PRIORITY 10 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 8 +#define STM32_ST_USE_TIMER 2 + +/* + * TRNG driver system settings. + */ +#define STM32_TRNG_USE_RNG1 FALSE + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USE_USART3 FALSE +#define STM32_UART_USE_UART4 FALSE +#define STM32_UART_USE_UART5 FALSE +#define STM32_UART_USE_USART6 FALSE +#define STM32_UART_USE_UART7 FALSE +#define STM32_UART_USE_UART8 FALSE +#define STM32_UART_USE_UART9 FALSE +#define STM32_UART_USE_USART10 FALSE +#define STM32_UART_USART1_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART1_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART2_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART2_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART3_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART3_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART4_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART4_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART5_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART5_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART6_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART6_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART7_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART7_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART8_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART8_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART9_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_UART9_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART10_RX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART10_TX_DMA_STREAM STM32_DMA_STREAM_ID_ANY +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_USART3_DMA_PRIORITY 0 +#define STM32_UART_UART4_DMA_PRIORITY 0 +#define STM32_UART_UART5_DMA_PRIORITY 0 +#define STM32_UART_USART6_DMA_PRIORITY 0 +#define STM32_UART_UART7_DMA_PRIORITY 0 +#define STM32_UART_UART8_DMA_PRIORITY 0 +#define STM32_UART_UART9_DMA_PRIORITY 0 +#define STM32_UART_USART10_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_OTG2 TRUE +#define STM32_USB_OTG2_IRQ_PRIORITY 14 +#define STM32_USB_OTG2_RX_FIFO_SIZE 1024 +#define STM32_USB_HOST_WAKEUP_DURATION 2 + +/* + * WDG driver system settings. + */ +#define STM32_WDG_USE_IWDG FALSE + +/* + * WSPI driver system settings. + */ +#define STM32_WSPI_USE_OCTOSPI1 FALSE +#define STM32_WSPI_USE_OCTOSPI2 FALSE +#define STM32_WSPI_OCTOSPI1_PRESCALER_VALUE 1 +#define STM32_WSPI_OCTOSPI2_PRESCALER_VALUE 1 +#define STM32_WSPI_OCTOSPI1_SSHIFT FALSE +#define STM32_WSPI_OCTOSPI2_SSHIFT FALSE +#define STM32_WSPI_OCTOSPI1_DHQC FALSE +#define STM32_WSPI_OCTOSPI2_DHQC FALSE +#define STM32_WSPI_OCTOSPI1_MDMA_CHANNEL STM32_MDMA_CHANNEL_ID_ANY +#define STM32_WSPI_OCTOSPI2_MDMA_CHANNEL STM32_MDMA_CHANNEL_ID_ANY +#define STM32_WSPI_OCTOSPI1_MDMA_PRIORITY 1 +#define STM32_WSPI_OCTOSPI2_MDMA_PRIORITY 1 +#define STM32_WSPI_OCTOSPI1_MDMA_IRQ_PRIORITY 10 +#define STM32_WSPI_OCTOSPI2_MDMA_IRQ_PRIORITY 10 +#define STM32_WSPI_DMA_ERROR_HOOK(wspip) osalSysHalt("MDMA failure") + +#endif /* MCUCONF_H */ diff --git a/platforms/chibios/boards/GENERIC_WB32_F3G71XX/board/board.c b/platforms/chibios/boards/GENERIC_WB32_F3G71XX/board/board.c index f74c9e8be7..e38a7e0054 100644 --- a/platforms/chibios/boards/GENERIC_WB32_F3G71XX/board/board.c +++ b/platforms/chibios/boards/GENERIC_WB32_F3G71XX/board/board.c @@ -80,7 +80,3 @@ void __early_init(void) { void boardInit(void) { } - -void restart_usb_driver(USBDriver *usbp) { - // Do nothing. Restarting the USB driver on these boards breaks it. -} diff --git a/platforms/chibios/boards/GENERIC_WB32_FQ95XX/board/board.c b/platforms/chibios/boards/GENERIC_WB32_FQ95XX/board/board.c index a99537fc27..22b4ff73b5 100644 --- a/platforms/chibios/boards/GENERIC_WB32_FQ95XX/board/board.c +++ b/platforms/chibios/boards/GENERIC_WB32_FQ95XX/board/board.c @@ -80,7 +80,3 @@ void __early_init(void) { void boardInit(void) { } - -void restart_usb_driver(USBDriver *usbp) { - // Do nothing. Restarting the USB driver on these boards breaks it. -} diff --git a/platforms/chibios/boards/IC_TEENSY_3_1/board/board.c b/platforms/chibios/boards/IC_TEENSY_3_1/board/board.c index 424e0c975b..36ae8051ee 100644 --- a/platforms/chibios/boards/IC_TEENSY_3_1/board/board.c +++ b/platforms/chibios/boards/IC_TEENSY_3_1/board/board.c @@ -144,8 +144,3 @@ void __early_init(void) { * @todo Add your board-specific code, if any. */ void boardInit(void) {} - - -void restart_usb_driver(USBDriver *usbp) { - // Do nothing. Restarting the USB driver on these boards breaks it. -} diff --git a/platforms/chibios/boards/PJRC_TEENSY_3_5/board/extra.c b/platforms/chibios/boards/PJRC_TEENSY_3_5/board/extra.c deleted file mode 100644 index 4940d6d99b..0000000000 --- a/platforms/chibios/boards/PJRC_TEENSY_3_5/board/extra.c +++ /dev/null @@ -1,7 +0,0 @@ -#include <hal.h> - -void restart_usb_driver(USBDriver *usbp) { - // Do nothing. Restarting the USB driver on the Teensy 3.6 breaks it, - // resulting in a keyboard which can wake up a PC from Suspend-to-RAM, but - // does not actually produce any keypresses until you un-plug and re-plug. -} diff --git a/platforms/chibios/boards/PJRC_TEENSY_3_6/board/board.mk b/platforms/chibios/boards/PJRC_TEENSY_3_6/board/board.mk deleted file mode 100644 index aba195db04..0000000000 --- a/platforms/chibios/boards/PJRC_TEENSY_3_6/board/board.mk +++ /dev/null @@ -1,11 +0,0 @@ -include $(CHIBIOS_CONTRIB)/os/hal/boards/PJRC_TEENSY_3_6/board.mk - -# List of all the board related files. -BOARDSRC += $(BOARD_PATH)/board/extra.c - -# Required include directories -BOARDINC += $(BOARD_PATH)/board - -# Shared variables -ALLCSRC += $(BOARDSRC) -ALLINC += $(BOARDINC) diff --git a/platforms/chibios/boards/PJRC_TEENSY_3_6/board/extra.c b/platforms/chibios/boards/PJRC_TEENSY_3_6/board/extra.c deleted file mode 100644 index 4940d6d99b..0000000000 --- a/platforms/chibios/boards/PJRC_TEENSY_3_6/board/extra.c +++ /dev/null @@ -1,7 +0,0 @@ -#include <hal.h> - -void restart_usb_driver(USBDriver *usbp) { - // Do nothing. Restarting the USB driver on the Teensy 3.6 breaks it, - // resulting in a keyboard which can wake up a PC from Suspend-to-RAM, but - // does not actually produce any keypresses until you un-plug and re-plug. -} diff --git a/platforms/chibios/boards/QMK_BLOK/configs/mcuconf.h b/platforms/chibios/boards/QMK_BLOK/configs/mcuconf.h index eb51e25171..0c2ef592d6 100644 --- a/platforms/chibios/boards/QMK_BLOK/configs/mcuconf.h +++ b/platforms/chibios/boards/QMK_BLOK/configs/mcuconf.h @@ -106,7 +106,6 @@ #define RP_USB_USE_USBD0 TRUE #define RP_USB_FORCE_VBUS_DETECT TRUE #define RP_USE_EXTERNAL_VBUS_DETECT FALSE -#define RP_USB_USE_SOF_INTR TRUE #define RP_USB_USE_ERROR_DATA_SEQ_INTR FALSE #endif /* MCUCONF_H */ diff --git a/platforms/chibios/boards/QMK_PM2040/configs/mcuconf.h b/platforms/chibios/boards/QMK_PM2040/configs/mcuconf.h index f19f08e93c..493dcf6434 100644 --- a/platforms/chibios/boards/QMK_PM2040/configs/mcuconf.h +++ b/platforms/chibios/boards/QMK_PM2040/configs/mcuconf.h @@ -106,7 +106,6 @@ #define RP_USB_USE_USBD0 TRUE #define RP_USB_FORCE_VBUS_DETECT TRUE #define RP_USE_EXTERNAL_VBUS_DETECT FALSE -#define RP_USB_USE_SOF_INTR TRUE #define RP_USB_USE_ERROR_DATA_SEQ_INTR FALSE #endif /* MCUCONF_H */ diff --git a/platforms/chibios/bootloaders/rp2040.c b/platforms/chibios/bootloaders/rp2040.c index bedc00f32e..524d13e636 100644 --- a/platforms/chibios/bootloaders/rp2040.c +++ b/platforms/chibios/bootloaders/rp2040.c @@ -1,9 +1,10 @@ // Copyright 2022 Stefan Kerkmann // SPDX-License-Identifier: GPL-2.0-or-later -#include "quantum.h" #include "hal.h" #include "bootloader.h" +#include "gpio.h" +#include "wait.h" #include "pico/bootrom.h" #if !defined(RP2040_BOOTLOADER_DOUBLE_TAP_RESET_LED) diff --git a/platforms/chibios/bootloaders/stm32_dfu.c b/platforms/chibios/bootloaders/stm32_dfu.c index f845bf21e9..fba3086e7a 100644 --- a/platforms/chibios/bootloaders/stm32_dfu.c +++ b/platforms/chibios/bootloaders/stm32_dfu.c @@ -1,4 +1,4 @@ -/* Copyright 2021 QMK +/* Copyright 2021-2023 QMK * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -15,12 +15,17 @@ */ #include "bootloader.h" +#include "util.h" #include <ch.h> #include <hal.h> #include "wait.h" -extern uint32_t __ram0_end__; +#ifndef STM32_BOOTLOADER_RAM_SYMBOL +# define STM32_BOOTLOADER_RAM_SYMBOL __ram0_end__ +#endif + +extern uint32_t STM32_BOOTLOADER_RAM_SYMBOL; #ifndef STM32_BOOTLOADER_DUAL_BANK # define STM32_BOOTLOADER_DUAL_BANK FALSE @@ -72,10 +77,25 @@ void enter_bootloader_mode_if_requested(void) {} /* This code should be checked whether it runs correctly on platforms */ # define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0)) # define BOOTLOADER_MAGIC 0xDEADBEEF -# define MAGIC_ADDR (unsigned long *)(SYMVAL(__ram0_end__) - 4) +# define MAGIC_ADDR (unsigned long *)(SYMVAL(STM32_BOOTLOADER_RAM_SYMBOL) - 4) + +__attribute__((weak)) void bootloader_marker_enable(void) { + uint32_t *marker = (uint32_t *)MAGIC_ADDR; + *marker = BOOTLOADER_MAGIC; // set magic flag => reset handler will jump into boot loader +} + +__attribute__((weak)) bool bootloader_marker_active(void) { + const uint32_t *marker = (const uint32_t *)MAGIC_ADDR; + return (*marker == BOOTLOADER_MAGIC) ? true : false; +} + +__attribute__((weak)) void bootloader_marker_disable(void) { + uint32_t *marker = (uint32_t *)MAGIC_ADDR; + *marker = 0; +} __attribute__((weak)) void bootloader_jump(void) { - *MAGIC_ADDR = BOOTLOADER_MAGIC; // set magic flag => reset handler will jump into boot loader + bootloader_marker_enable(); NVIC_SystemReset(); } @@ -84,18 +104,44 @@ __attribute__((weak)) void mcu_reset(void) { } void enter_bootloader_mode_if_requested(void) { - unsigned long *check = MAGIC_ADDR; - if (*check == BOOTLOADER_MAGIC) { - *check = 0; + if (bootloader_marker_active()) { + bootloader_marker_disable(); + + struct system_memory_vector_t { + uint32_t stack_top; + void (*entrypoint)(void); + }; + const struct system_memory_vector_t *bootloader = (const struct system_memory_vector_t *)(STM32_BOOTLOADER_ADDRESS); + + __disable_irq(); + +# if defined(QMK_MCU_ARCH_CORTEX_M7) + SCB_DisableDCache(); + SCB_DisableICache(); +# endif + +# if defined(__MPU_PRESENT) && (__MPU_PRESENT == 1U) + ARM_MPU_Disable(); +# endif + + SysTick->CTRL = 0; + SysTick->VAL = 0; + SysTick->LOAD = 0; + + // Clear interrupt enable and interrupt pending registers + for (int i = 0; i < ARRAY_SIZE(NVIC->ICER); i++) { + NVIC->ICER[i] = 0xFFFFFFFF; + NVIC->ICPR[i] = 0xFFFFFFFF; + } + __set_CONTROL(0); - __set_MSP(*(__IO uint32_t *)STM32_BOOTLOADER_ADDRESS); + __set_MSP(bootloader->stack_top); __enable_irq(); - typedef void (*BootJump_t)(void); - BootJump_t boot_jump = *(BootJump_t *)(STM32_BOOTLOADER_ADDRESS + 4); - boot_jump(); - while (1) - ; + // Jump to bootloader + bootloader->entrypoint(); + while (true) { + } } } #endif diff --git a/platforms/chibios/chibios_config.h b/platforms/chibios/chibios_config.h index 52632a051e..1f8a7842fe 100644 --- a/platforms/chibios/chibios_config.h +++ b/platforms/chibios/chibios_config.h @@ -71,7 +71,11 @@ // STM32 compatibility #if defined(MCU_STM32) -# define CPU_CLOCK STM32_SYSCLK +# if defined(STM32_CORE_CK) +# define CPU_CLOCK STM32_CORE_CK +# else +# define CPU_CLOCK STM32_SYSCLK +# endif # if defined(STM32F1XX) # define USE_GPIOV1 diff --git a/platforms/chibios/config.h b/platforms/chibios/config.h new file mode 100644 index 0000000000..006415a5dc --- /dev/null +++ b/platforms/chibios/config.h @@ -0,0 +1,7 @@ +// Copyright 2023 Nick Brassel (@tzarc) +// SPDX-License-Identifier: GPL-2.0-or-later +#pragma once + +#ifndef CORTEX_ENABLE_WFI_IDLE +# define CORTEX_ENABLE_WFI_IDLE TRUE +#endif // CORTEX_ENABLE_WFI_IDLE diff --git a/platforms/chibios/drivers/backlight_pwm.c b/platforms/chibios/drivers/backlight_pwm.c new file mode 100644 index 0000000000..01e6f71307 --- /dev/null +++ b/platforms/chibios/drivers/backlight_pwm.c @@ -0,0 +1,173 @@ +#include "backlight.h" +#include "gpio.h" +#include "wait.h" +#include <hal.h> + +// Maximum duty cycle limit +#ifndef BACKLIGHT_LIMIT_VAL +# define BACKLIGHT_LIMIT_VAL 255 +#endif + +#ifndef BACKLIGHT_PAL_MODE +# if defined(USE_GPIOV1) +# define BACKLIGHT_PAL_MODE PAL_MODE_ALTERNATE_PUSHPULL +# else +// GPIOV2 && GPIOV3 +# define BACKLIGHT_PAL_MODE 2 +# endif +#endif + +// GENERIC +#ifndef BACKLIGHT_PWM_DRIVER +# define BACKLIGHT_PWM_DRIVER PWMD4 +#endif +#ifndef BACKLIGHT_PWM_CHANNEL +# define BACKLIGHT_PWM_CHANNEL 3 +#endif + +// Support for pins which are on TIM1_CH1N - requires STM32_PWM_USE_ADVANCED +#ifdef BACKLIGHT_PWM_COMPLEMENTARY_OUTPUT +# if BACKLIGHT_ON_STATE == 1 +# define PWM_OUTPUT_MODE PWM_COMPLEMENTARY_OUTPUT_ACTIVE_LOW; +# else +# define PWM_OUTPUT_MODE PWM_COMPLEMENTARY_OUTPUT_ACTIVE_HIGH; +# endif +#else +# if BACKLIGHT_ON_STATE == 1 +# define PWM_OUTPUT_MODE PWM_OUTPUT_ACTIVE_HIGH; +# else +# define PWM_OUTPUT_MODE PWM_OUTPUT_ACTIVE_LOW; +# endif +#endif + +#ifndef BACKLIGHT_PWM_COUNTER_FREQUENCY +# define BACKLIGHT_PWM_COUNTER_FREQUENCY 0xFFFF +#endif + +#ifndef BACKLIGHT_PWM_PERIOD +# define BACKLIGHT_PWM_PERIOD 256 +#endif + +static PWMConfig pwmCFG = { + .frequency = BACKLIGHT_PWM_COUNTER_FREQUENCY, /* PWM clock frequency */ + .period = BACKLIGHT_PWM_PERIOD, /* PWM period in counter ticks. e.g. clock frequency is 10KHz, period is 256 ticks then t_period is 25.6ms */ +}; + +#ifdef BACKLIGHT_BREATHING +static virtual_timer_t breathing_vt; +#endif + +// See http://jared.geek.nz/2013/feb/linear-led-pwm +static uint16_t cie_lightness(uint16_t v) { + if (v <= 5243) // if below 8% of max + return v / 9; // same as dividing by 900% + else { + uint32_t y = (((uint32_t)v + 10486) << 8) / (10486 + 0xFFFFUL); // add 16% of max and compare + // to get a useful result with integer division, we shift left in the expression above + // and revert what we've done again after squaring. + y = y * y * y >> 8; + if (y > 0xFFFFUL) { // prevent overflow + return 0xFFFFU; + } else { + return (uint16_t)y; + } + } +} + +static uint32_t rescale_limit_val(uint32_t val) { + // rescale the supplied backlight value to be in terms of the value limit + return (val * (BACKLIGHT_LIMIT_VAL + 1)) / 256; +} + +void backlight_init_ports(void) { +#ifdef USE_GPIOV1 + palSetPadMode(PAL_PORT(BACKLIGHT_PIN), PAL_PAD(BACKLIGHT_PIN), BACKLIGHT_PAL_MODE); +#else + palSetPadMode(PAL_PORT(BACKLIGHT_PIN), PAL_PAD(BACKLIGHT_PIN), PAL_MODE_ALTERNATE(BACKLIGHT_PAL_MODE)); +#endif + + pwmCFG.channels[BACKLIGHT_PWM_CHANNEL - 1].mode = PWM_OUTPUT_MODE; + pwmStart(&BACKLIGHT_PWM_DRIVER, &pwmCFG); + + backlight_set(get_backlight_level()); + +#ifdef BACKLIGHT_BREATHING + chVTObjectInit(&breathing_vt); + if (is_backlight_breathing()) { + breathing_enable(); + } +#endif +} + +void backlight_set(uint8_t level) { + if (level > BACKLIGHT_LEVELS) { + level = BACKLIGHT_LEVELS; + } + + if (level == 0) { + // Turn backlight off + pwmDisableChannel(&BACKLIGHT_PWM_DRIVER, BACKLIGHT_PWM_CHANNEL - 1); + } else { + // Turn backlight on + uint32_t duty = (uint32_t)(cie_lightness(rescale_limit_val(0xFFFF * (uint32_t)level / BACKLIGHT_LEVELS))); + pwmEnableChannel(&BACKLIGHT_PWM_DRIVER, BACKLIGHT_PWM_CHANNEL - 1, PWM_FRACTION_TO_WIDTH(&BACKLIGHT_PWM_DRIVER, 0xFFFF, duty)); + } +} + +void backlight_task(void) {} + +#ifdef BACKLIGHT_BREATHING + +# define BREATHING_STEPS 128 + +/* To generate breathing curve in python: + * from math import sin, pi; [int(sin(x/128.0*pi)**4*255) for x in range(128)] + */ +static const uint8_t breathing_table[BREATHING_STEPS] = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 3, 4, 5, 6, 8, 10, 12, 15, 17, 20, 24, 28, 32, 36, 41, 46, 51, 57, 63, 70, 76, 83, 91, 98, 106, 113, 121, 129, 138, 146, 154, 162, 170, 178, 185, 193, 200, 207, 213, 220, 225, 231, 235, 240, 244, 247, 250, 252, 253, 254, 255, 254, 253, 252, 250, 247, 244, 240, 235, 231, 225, 220, 213, 207, 200, 193, 185, 178, 170, 162, 154, 146, 138, 129, 121, 113, 106, 98, 91, 83, 76, 70, 63, 57, 51, 46, 41, 36, 32, 28, 24, 20, 17, 15, 12, 10, 8, 6, 5, 4, 3, 2, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; + +static void breathing_callback(virtual_timer_t *vtp, void *p); + +bool is_breathing(void) { + return chVTIsArmed(&breathing_vt); +} + +void breathing_enable(void) { + /* Update frequency is 256Hz -> 3906us intervals */ + chVTSetContinuous(&breathing_vt, TIME_US2I(3906), breathing_callback, NULL); +} + +void breathing_disable(void) { + chVTReset(&breathing_vt); + + // Restore backlight level + backlight_set(get_backlight_level()); +} + +// Use this before the cie_lightness function. +static inline uint16_t scale_backlight(uint16_t v) { + return v / BACKLIGHT_LEVELS * get_backlight_level(); +} + +static void breathing_callback(virtual_timer_t *vtp, void *p) { + uint8_t breathing_period = get_breathing_period(); + uint16_t interval = (uint16_t)breathing_period * 256 / BREATHING_STEPS; + + // resetting after one period to prevent ugly reset at overflow. + static uint16_t breathing_counter = 0; + breathing_counter = (breathing_counter + 1) % (breathing_period * 256); + uint8_t index = breathing_counter / interval % BREATHING_STEPS; + uint32_t duty = cie_lightness(rescale_limit_val(scale_backlight(breathing_table[index] * 256))); + + chSysLockFromISR(); + pwmEnableChannelI(&BACKLIGHT_PWM_DRIVER, BACKLIGHT_PWM_CHANNEL - 1, PWM_FRACTION_TO_WIDTH(&BACKLIGHT_PWM_DRIVER, 0xFFFF, duty)); + chSysUnlockFromISR(); +} + +// TODO: integrate generic pulse solution +void breathing_pulse(void) { + backlight_set(is_backlight_enabled() ? 0 : BACKLIGHT_LEVELS); + wait_ms(10); + backlight_set(is_backlight_enabled() ? get_backlight_level() : 0); +} + +#endif diff --git a/platforms/chibios/drivers/backlight_timer.c b/platforms/chibios/drivers/backlight_timer.c new file mode 100644 index 0000000000..0fabee93b1 --- /dev/null +++ b/platforms/chibios/drivers/backlight_timer.c @@ -0,0 +1,178 @@ +#include "backlight.h" +#include "backlight_driver_common.h" +#include "wait.h" + +#ifndef BACKLIGHT_GPT_DRIVER +# define BACKLIGHT_GPT_DRIVER GPTD15 +#endif + +// Platform specific implementations +static void backlight_timer_configure(bool enable); +static void backlight_timer_set_duty(uint16_t duty); +static uint16_t backlight_timer_get_duty(void); + +// See http://jared.geek.nz/2013/feb/linear-led-pwm +static uint16_t cie_lightness(uint16_t v) { + if (v <= 5243) // if below 8% of max + return v / 9; // same as dividing by 900% + else { + uint32_t y = (((uint32_t)v + 10486) << 8) / (10486 + 0xFFFFUL); // add 16% of max and compare + // to get a useful result with integer division, we shift left in the expression above + // and revert what we've done again after squaring. + y = y * y * y >> 8; + if (y > 0xFFFFUL) // prevent overflow + return 0xFFFFU; + else + return (uint16_t)y; + } +} + +void backlight_init_ports(void) { + backlight_pins_init(); + + backlight_set(get_backlight_level()); + +#ifdef BACKLIGHT_BREATHING + if (is_backlight_breathing()) { + breathing_enable(); + } +#endif +} + +void backlight_set(uint8_t level) { + if (level > BACKLIGHT_LEVELS) level = BACKLIGHT_LEVELS; + + backlight_pins_off(); + + backlight_timer_set_duty(cie_lightness(0xFFFFU / BACKLIGHT_LEVELS * level)); + backlight_timer_configure(level != 0); +} + +static void backlight_timer_top(void) { +#ifdef BACKLIGHT_BREATHING + if (is_breathing()) { + breathing_task(); + } +#endif + + if (backlight_timer_get_duty() > 256) { + backlight_pins_on(); + } +} + +static void backlight_timer_cmp(void) { + backlight_pins_off(); +} + +void backlight_task(void) {} + +#ifdef BACKLIGHT_BREATHING +# define BREATHING_STEPS 128 + +static bool breathing = false; +static uint16_t breathing_counter = 0; + +/* To generate breathing curve in python: + * from math import sin, pi; [int(sin(x/128.0*pi)**4*255) for x in range(128)] + */ +static const uint8_t breathing_table[BREATHING_STEPS] = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 2, 3, 4, 5, 6, 8, 10, 12, 15, 17, 20, 24, 28, 32, 36, 41, 46, 51, 57, 63, 70, 76, 83, 91, 98, 106, 113, 121, 129, 138, 146, 154, 162, 170, 178, 185, 193, 200, 207, 213, 220, 225, 231, 235, 240, 244, 247, 250, 252, 253, 254, 255, 254, 253, 252, 250, 247, 244, 240, 235, 231, 225, 220, 213, 207, 200, 193, 185, 178, 170, 162, 154, 146, 138, 129, 121, 113, 106, 98, 91, 83, 76, 70, 63, 57, 51, 46, 41, 36, 32, 28, 24, 20, 17, 15, 12, 10, 8, 6, 5, 4, 3, 2, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}; + +// Use this before the cie_lightness function. +static inline uint16_t scale_backlight(uint16_t v) { + return v / BACKLIGHT_LEVELS * get_backlight_level(); +} + +void breathing_task(void) { + uint8_t breathing_period = get_breathing_period(); + uint16_t interval = (uint16_t)breathing_period * 256 / BREATHING_STEPS; + // resetting after one period to prevent ugly reset at overflow. + breathing_counter = (breathing_counter + 1) % (breathing_period * 256); + uint8_t index = breathing_counter / interval % BREATHING_STEPS; + + // printf("index:%u\n", index); + + backlight_timer_set_duty(cie_lightness(scale_backlight((uint16_t)breathing_table[index] * 256))); +} + +bool is_breathing(void) { + return breathing; +} + +void breathing_enable(void) { + breathing_counter = 0; + breathing = true; +} +void breathing_disable(void) { + breathing = false; +} + +void breathing_pulse(void) { + backlight_set(is_backlight_enabled() ? 0 : BACKLIGHT_LEVELS); + wait_ms(10); + backlight_set(is_backlight_enabled() ? get_backlight_level() : 0); +} +#endif + +#ifdef PROTOCOL_CHIBIOS +// On Platforms where timers fire every tick and have no capture/top events +// - fake event in the normal timer callback +uint16_t s_duty = 0; + +static void timerCallback(void) { + /* Software PWM + * timer:1111 1111 1111 1111 + * \______/| \_______/____ count(0-255) + * \ \______________ unused(1) + * \__________________ index of step table(0-127) + */ + + // this works for cca 65536 irqs/sec + static union { + uint16_t raw; + struct { + uint16_t count : 8; + uint8_t dummy : 1; + uint8_t index : 7; + } pwm; + } timer = {.raw = 0}; + + timer.raw++; + + if (timer.pwm.count == 0) { + // LED on + backlight_timer_top(); + } else if (timer.pwm.count == (s_duty / 256)) { + // LED off + backlight_timer_cmp(); + } +} + +static void backlight_timer_set_duty(uint16_t duty) { + s_duty = duty; +} +static uint16_t backlight_timer_get_duty(void) { + return s_duty; +} + +// ChibiOS - Map GPT timer onto Software PWM +static void gptTimerCallback(GPTDriver *gptp) { + (void)gptp; + timerCallback(); +} + +static void backlight_timer_configure(bool enable) { + static const GPTConfig gptcfg = {1000000, gptTimerCallback, 0, 0}; + + static bool s_init = false; + if (!s_init) { + gptStart(&BACKLIGHT_GPT_DRIVER, &gptcfg); + s_init = true; + } + + if (enable) { + gptStartContinuous(&BACKLIGHT_GPT_DRIVER, gptcfg.frequency / 0xFFFF); + } else { + gptStopTimer(&BACKLIGHT_GPT_DRIVER); + } +} +#endif diff --git a/platforms/chibios/drivers/i2c_master.c b/platforms/chibios/drivers/i2c_master.c index 4c7a5daa17..7c49f9d005 100644 --- a/platforms/chibios/drivers/i2c_master.c +++ b/platforms/chibios/drivers/i2c_master.c @@ -24,8 +24,10 @@ * STM32_I2C_USE_I2C1 is TRUE in the mcuconf.h file. Pins B6 and B7 are used * but using any other I2C pins should be trivial. */ -#include "quantum.h" + #include "i2c_master.h" +#include "gpio.h" +#include "chibios_config.h" #include <string.h> #include <ch.h> #include <hal.h> diff --git a/platforms/chibios/drivers/serial.c b/platforms/chibios/drivers/serial.c index 0dd8e71ae8..f087d0c2ed 100644 --- a/platforms/chibios/drivers/serial.c +++ b/platforms/chibios/drivers/serial.c @@ -2,8 +2,8 @@ * WARNING: be careful changing this code, it is very timing dependent */ -#include "quantum.h" #include "serial.h" +#include "gpio.h" #include "wait.h" #include "synchronization_util.h" diff --git a/platforms/chibios/drivers/serial_protocol.c b/platforms/chibios/drivers/serial_protocol.c index ccaf73282d..e0f583ccde 100644 --- a/platforms/chibios/drivers/serial_protocol.c +++ b/platforms/chibios/drivers/serial_protocol.c @@ -3,10 +3,8 @@ #include <ch.h> -#include "quantum.h" #include "serial.h" #include "serial_protocol.h" -#include "printf.h" #include "synchronization_util.h" static inline bool initiate_transaction(uint8_t transaction_id); diff --git a/platforms/chibios/drivers/serial_usart.c b/platforms/chibios/drivers/serial_usart.c index 6ebbf7c8ca..767ef8726f 100644 --- a/platforms/chibios/drivers/serial_usart.c +++ b/platforms/chibios/drivers/serial_usart.c @@ -5,6 +5,7 @@ #include "serial_usart.h" #include "serial_protocol.h" #include "synchronization_util.h" +#include "chibios_config.h" #if defined(SERIAL_USART_CONFIG) static QMKSerialConfig serial_config = SERIAL_USART_CONFIG; diff --git a/platforms/chibios/drivers/serial_usart.h b/platforms/chibios/drivers/serial_usart.h index fa062cd736..dec8a292e9 100644 --- a/platforms/chibios/drivers/serial_usart.h +++ b/platforms/chibios/drivers/serial_usart.h @@ -3,7 +3,6 @@ #pragma once -#include "quantum.h" #include "serial.h" #include <hal.h> diff --git a/platforms/chibios/drivers/uart.c b/platforms/chibios/drivers/uart.c index 34f77232b6..39a59dd445 100644 --- a/platforms/chibios/drivers/uart.c +++ b/platforms/chibios/drivers/uart.c @@ -16,8 +16,6 @@ #include "uart.h" -#include "quantum.h" - #if defined(MCU_KINETIS) static SerialConfig serialConfig = {SERIAL_DEFAULT_BITRATE}; #elif defined(WB32F3G71xx) || defined(WB32FQ95xx) diff --git a/platforms/chibios/drivers/uart.h b/platforms/chibios/drivers/uart.h index e9e3b0855b..d1917bfc80 100644 --- a/platforms/chibios/drivers/uart.h +++ b/platforms/chibios/drivers/uart.h @@ -17,6 +17,7 @@ #pragma once #include <stdint.h> +#include <stdbool.h> #include <hal.h> diff --git a/platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c b/platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c index 937fa5de6f..d775ec29d5 100644 --- a/platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c +++ b/platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c @@ -1,12 +1,10 @@ // Copyright 2022 Marek Kraus (@gamelaster) // SPDX-License-Identifier: GPL-2.0-or-later -#include "quantum.h" - #include "hardware/pio.h" #include "hardware/clocks.h" #include "ps2.h" -#include "print.h" +#include "debug.h" #if !defined(MCU_RP) # error PIO Driver is only available for Raspberry Pi 2040 MCUs! diff --git a/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c b/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c index dd4723a086..3aa8e1165f 100644 --- a/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c +++ b/platforms/chibios/drivers/vendor/RP/RP2040/serial_vendor.c @@ -1,11 +1,12 @@ // Copyright 2022 Stefan Kerkmann // SPDX-License-Identifier: GPL-2.0-or-later -#include "quantum.h" #include "serial_usart.h" #include "serial_protocol.h" #include "hardware/pio.h" #include "hardware/clocks.h" +#include "wait.h" +#include "debug.h" #if !defined(MCU_RP) # error PIO Driver is only available for Raspberry Pi 2040 MCUs! diff --git a/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c b/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c index 99a6cfaba9..8d59e13bb2 100644 --- a/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c +++ b/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c @@ -2,13 +2,19 @@ // SPDX-License-Identifier: GPL-2.0-or-later #include "ws2812.h" -#include "hardware/timer.h" -#include "hardware/clocks.h" + // Keep this exact include order otherwise we run into naming conflicts between // pico-sdk and rp2040.h which we don't control. -#include "quantum.h" +#include "hardware/timer.h" +#include "hardware/clocks.h" +#include <hal.h> #include "hardware/pio.h" +#include "gpio.h" +#include "debug.h" +#include "wait.h" +#include "util.h" + #if !defined(MCU_RP) # error PIO Driver is only available for Raspberry Pi 2040 MCUs! #endif diff --git a/platforms/chibios/drivers/ws2812_bitbang.c b/platforms/chibios/drivers/ws2812_bitbang.c index d05deb1a50..c55e0f654c 100644 --- a/platforms/chibios/drivers/ws2812_bitbang.c +++ b/platforms/chibios/drivers/ws2812_bitbang.c @@ -1,7 +1,7 @@ -#include "quantum.h" #include "ws2812.h" -#include <ch.h> -#include <hal.h> + +#include "gpio.h" +#include "chibios_config.h" /* Adapted from https://github.com/bigjosh/SimpleNeoPixelDemo/ */ diff --git a/platforms/chibios/drivers/ws2812_pwm.c b/platforms/chibios/drivers/ws2812_pwm.c index 04c8279a97..cfee547a82 100644 --- a/platforms/chibios/drivers/ws2812_pwm.c +++ b/platforms/chibios/drivers/ws2812_pwm.c @@ -1,6 +1,6 @@ #include "ws2812.h" -#include "quantum.h" -#include <hal.h> +#include "gpio.h" +#include "chibios_config.h" /* Adapted from https://github.com/joewa/WS2812-LED-Driver_ChibiOS/ */ diff --git a/platforms/chibios/drivers/ws2812_spi.c b/platforms/chibios/drivers/ws2812_spi.c index c28f5007f1..f188576e04 100644 --- a/platforms/chibios/drivers/ws2812_spi.c +++ b/platforms/chibios/drivers/ws2812_spi.c @@ -1,5 +1,7 @@ -#include "quantum.h" #include "ws2812.h" +#include "gpio.h" +#include "util.h" +#include "chibios_config.h" /* Adapted from https://github.com/gamazeps/ws2812b-chibios-SPIDMA/ */ diff --git a/platforms/chibios/mcu_selection.mk b/platforms/chibios/mcu_selection.mk index f14b16b169..5122ed4634 100644 --- a/platforms/chibios/mcu_selection.mk +++ b/platforms/chibios/mcu_selection.mk @@ -705,6 +705,45 @@ ifneq (,$(filter $(MCU),STM32L412 STM32L422)) STM32_BOOTLOADER_ADDRESS ?= 0x1FFF0000 endif +ifneq (,$(filter $(MCU),STM32H723 STM32H733)) + # Cortex version + MCU = cortex-m7 + + # ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 + ARMV = 7 + + ## chip/board settings + # - the next two should match the directories in + # <chibios[-contrib]>/os/hal/ports/$(MCU_PORT_NAME)/$(MCU_SERIES) + # OR + # <chibios[-contrib]>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) + MCU_FAMILY = STM32 + MCU_SERIES = STM32H7xx + + # Linker script to use + # - it should exist either in <chibios>/os/common/startup/ARMCMx/compilers/GCC/ld/ + # or <keyboard_dir>/ld/ + MCU_LDSCRIPT ?= STM32H723xG_ITCM64k + + # Startup code to use + # - it should exist in <chibios>/os/common/startup/ARMCMx/compilers/GCC/mk/ + MCU_STARTUP ?= stm32h7xx + + # Board: it should exist either in <chibios>/os/hal/boards/, + # <keyboard_dir>/boards/, or drivers/boards/ + BOARD ?= GENERIC_STM32_H723XG + + PLATFORM_NAME ?= platform_type2 + + USE_FPU ?= yes + + # UF2 settings + UF2_FAMILY ?= STM32H7 + + # Bootloader address for STM32 DFU + STM32_BOOTLOADER_ADDRESS ?= 0x1FF09800 +endif + ifneq ($(findstring WB32F3G71, $(MCU)),) # Cortex version MCU = cortex-m3 diff --git a/platforms/chibios/platform.mk b/platforms/chibios/platform.mk index 6304b42d87..081b001e6d 100644 --- a/platforms/chibios/platform.mk +++ b/platforms/chibios/platform.mk @@ -432,6 +432,15 @@ else endif endif +# Extra config.h files for the platform +ifneq ("$(wildcard $(PLATFORM_COMMON_DIR)/vendors/$(MCU_FAMILY)/$(MCU_SERIES)/config.h)","") + CONFIG_H += $(PLATFORM_COMMON_DIR)/vendors/$(MCU_FAMILY)/$(MCU_SERIES)/config.h +endif +ifneq ("$(wildcard $(PLATFORM_COMMON_DIR)/vendors/$(MCU_FAMILY)/config.h)","") + CONFIG_H += $(PLATFORM_COMMON_DIR)/vendors/$(MCU_FAMILY)/config.h +endif +CONFIG_H += $(PLATFORM_COMMON_DIR)/config.h + # Assembler flags ASFLAGS += $(SHARED_ASFLAGS) $(TOOLCHAIN_ASFLAGS) diff --git a/platforms/chibios/sleep_led.c b/platforms/chibios/sleep_led.c index a777d60468..a35514bf2e 100644 --- a/platforms/chibios/sleep_led.c +++ b/platforms/chibios/sleep_led.c @@ -41,17 +41,20 @@ void sleep_led_timer_callback(void) { uint8_t duration : 2; uint8_t index : 6; } pwm; - } timer = {.row = 0}; + } timer = {.row = 0}; + static led_t led_state = {0}; timer.row++; // LED on if (timer.pwm.count == 0) { - led_set(1 << USB_LED_CAPS_LOCK); + led_state.caps_lock = true; + led_set(led_state.raw); } // LED off if (timer.pwm.count == breathing_table[timer.pwm.index]) { - led_set(0); + led_state.caps_lock = false; + led_set(led_state.raw); } } @@ -190,7 +193,7 @@ void sleep_led_toggle(void) { void sleep_led_init(void) {} void sleep_led_enable(void) { - led_set(1 << USB_LED_CAPS_LOCK); + led_set(2); // Caps Lock } void sleep_led_disable(void) { diff --git a/platforms/chibios/suspend.c b/platforms/chibios/suspend.c index ce03433e3a..a937ccf059 100644 --- a/platforms/chibios/suspend.c +++ b/platforms/chibios/suspend.c @@ -42,6 +42,7 @@ void suspend_wakeup_init(void) { clear_keys(); #ifdef MOUSEKEY_ENABLE mousekey_clear(); + mousekey_send(); #endif /* MOUSEKEY_ENABLE */ #ifdef PROGRAMMABLE_BUTTON_ENABLE programmable_button_clear(); diff --git a/platforms/chibios/vendors/RP/pico_sdk_shims.c b/platforms/chibios/vendors/RP/pico_sdk_shims.c index 239155c086..caab400531 100644 --- a/platforms/chibios/vendors/RP/pico_sdk_shims.c +++ b/platforms/chibios/vendors/RP/pico_sdk_shims.c @@ -2,7 +2,8 @@ // SPDX-License-Identifier: GPL-2.0-or-later #include <stdbool.h> -#include <ch.h> + +extern void chSysHalt(const char *reason) __attribute__((noreturn)); void panic(const char *fmt, ...) { chSysHalt(fmt); diff --git a/platforms/chibios/wait.c b/platforms/chibios/wait.c index 88cb5e6d54..7fe6d477b8 100644 --- a/platforms/chibios/wait.c +++ b/platforms/chibios/wait.c @@ -21,7 +21,7 @@ #ifdef WAIT_US_TIMER void wait_us(uint16_t duration) { - static const GPTConfig gpt_cfg = {1000000, NULL, 0, 0}; /* 1MHz timer, no callback */ + static const GPTConfig gpt_cfg = {.frequency = 1000000}; /* 1MHz timer, no callback */ if (duration == 0) { duration = 1; diff --git a/platforms/test/drivers/audio_pwm.h b/platforms/test/drivers/audio_pwm.h new file mode 100644 index 0000000000..9a3fa88cec --- /dev/null +++ b/platforms/test/drivers/audio_pwm.h @@ -0,0 +1,16 @@ +// Copyright 2023 Google LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 2 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. + +#pragma once diff --git a/platforms/test/drivers/audio_pwm_hardware.c b/platforms/test/drivers/audio_pwm_hardware.c new file mode 100644 index 0000000000..336e4f5844 --- /dev/null +++ b/platforms/test/drivers/audio_pwm_hardware.c @@ -0,0 +1,20 @@ +// Copyright 2023 Google LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 2 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. + +#include "audio.h" + +void audio_driver_initialize(void) {} +void audio_driver_start() {} +void audio_driver_stop() {} |