summaryrefslogtreecommitdiff
path: root/platforms/chibios/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'platforms/chibios/drivers')
-rw-r--r--platforms/chibios/drivers/audio_dac_additive.c6
-rw-r--r--platforms/chibios/drivers/audio_dac_basic.c6
-rw-r--r--platforms/chibios/drivers/ps2/ps2_io.c1
-rw-r--r--platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c271
-rw-r--r--platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c6
-rw-r--r--platforms/chibios/drivers/ws2812_bitbang.c (renamed from platforms/chibios/drivers/ws2812.c)10
-rw-r--r--platforms/chibios/drivers/ws2812_pwm.c2
-rw-r--r--platforms/chibios/drivers/ws2812_spi.c10
8 files changed, 298 insertions, 14 deletions
diff --git a/platforms/chibios/drivers/audio_dac_additive.c b/platforms/chibios/drivers/audio_dac_additive.c
index 68ce13788e..d29147ca3b 100644
--- a/platforms/chibios/drivers/audio_dac_additive.c
+++ b/platforms/chibios/drivers/audio_dac_additive.c
@@ -19,6 +19,10 @@
#include <ch.h>
#include <hal.h>
+// Need to disable GCC's "tautological-compare" warning for this file, as it causes issues when running `KEEP_INTERMEDIATES=yes`. Corresponding pop at the end of the file.
+#pragma GCC diagnostic push
+#pragma GCC diagnostic ignored "-Wtautological-compare"
+
/*
Audio Driver: DAC
@@ -335,3 +339,5 @@ void audio_driver_start(void) {
active_tones_snapshot_length = 0;
state = OUTPUT_SHOULD_START;
}
+
+#pragma GCC diagnostic pop
diff --git a/platforms/chibios/drivers/audio_dac_basic.c b/platforms/chibios/drivers/audio_dac_basic.c
index 5f0cbf8f84..4ea23a2158 100644
--- a/platforms/chibios/drivers/audio_dac_basic.c
+++ b/platforms/chibios/drivers/audio_dac_basic.c
@@ -19,6 +19,10 @@
#include "ch.h"
#include "hal.h"
+// Need to disable GCC's "tautological-compare" warning for this file, as it causes issues when running `KEEP_INTERMEDIATES=yes`. Corresponding pop at the end of the file.
+#pragma GCC diagnostic push
+#pragma GCC diagnostic ignored "-Wtautological-compare"
+
/*
Audio Driver: DAC
@@ -247,3 +251,5 @@ void audio_driver_start(void) {
}
gptStartContinuous(&AUDIO_STATE_TIMER, 2U);
}
+
+#pragma GCC diagnostic pop
diff --git a/platforms/chibios/drivers/ps2/ps2_io.c b/platforms/chibios/drivers/ps2/ps2_io.c
index 906d85d848..9eb56d63da 100644
--- a/platforms/chibios/drivers/ps2/ps2_io.c
+++ b/platforms/chibios/drivers/ps2/ps2_io.c
@@ -4,6 +4,7 @@
// chibiOS headers
#include "ch.h"
#include "hal.h"
+#include "gpio.h"
/* Check port settings for clock and data line */
#if !(defined(PS2_CLOCK_PIN))
diff --git a/platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c b/platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c
new file mode 100644
index 0000000000..937fa5de6f
--- /dev/null
+++ b/platforms/chibios/drivers/vendor/RP/RP2040/ps2_vendor.c
@@ -0,0 +1,271 @@
+// Copyright 2022 Marek Kraus (@gamelaster)
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "quantum.h"
+
+#include "hardware/pio.h"
+#include "hardware/clocks.h"
+#include "ps2.h"
+#include "print.h"
+
+#if !defined(MCU_RP)
+# error PIO Driver is only available for Raspberry Pi 2040 MCUs!
+#endif
+
+#if defined(PS2_ENABLE)
+# if defined(PS2_MOUSE_ENABLE)
+# if !defined(PS2_MOUSE_USE_REMOTE_MODE)
+# define BUFFERED_MODE_ENABLE
+# endif
+# else // PS2 Keyboard
+# define BUFFERED_MODE_ENABLE
+# endif
+#endif
+
+#if PS2_DATA_PIN + 1 != PS2_CLOCK_PIN
+# error PS/2 Clock pin must be followed by data pin!
+#endif
+
+static inline void pio_serve_interrupt(void);
+
+#if defined(PS2_PIO_USE_PIO1)
+static const PIO pio = pio1;
+
+OSAL_IRQ_HANDLER(RP_PIO1_IRQ_0_HANDLER) {
+ OSAL_IRQ_PROLOGUE();
+ pio_serve_interrupt();
+ OSAL_IRQ_EPILOGUE();
+}
+#else
+static const PIO pio = pio0;
+
+OSAL_IRQ_HANDLER(RP_PIO0_IRQ_0_HANDLER) {
+ OSAL_IRQ_PROLOGUE();
+ pio_serve_interrupt();
+ OSAL_IRQ_EPILOGUE();
+}
+#endif
+
+#define PS2_WRAP_TARGET 0
+#define PS2_WRAP 20
+
+// clang-format off
+static const uint16_t ps2_program_instructions[] = {
+ // .wrap_target
+ 0x00c7, // 0: jmp pin, 7
+ 0xe02a, // 1: set x, 10
+ 0x2021, // 2: wait 0 pin, 1
+ 0x4001, // 3: in pins, 1
+ 0x20a1, // 4: wait 1 pin, 1
+ 0x0042, // 5: jmp x--, 2
+ 0x0000, // 6: jmp 0
+ 0x00e9, // 7: jmp !osre, 9
+ 0x0000, // 8: jmp 0
+ 0xff81, // 9: set pindirs, 1 [31]
+ 0xe280, // 10: set pindirs, 0 [2]
+ 0xe082, // 11: set pindirs, 2
+ 0x2021, // 12: wait 0 pin, 1
+ 0xe029, // 13: set x, 9
+ 0x6081, // 14: out pindirs, 1
+ 0x20a1, // 15: wait 1 pin, 1
+ 0x2021, // 16: wait 0 pin, 1
+ 0x004e, // 17: jmp x--, 14
+ 0xe083, // 18: set pindirs, 3
+ 0x2021, // 19: wait 0 pin, 1
+ 0x20a1, // 20: wait 1 pin, 1
+ // .wrap
+};
+// clang-format on
+
+static const struct pio_program ps2_program = {
+ .instructions = ps2_program_instructions,
+ .length = 21,
+ .origin = -1,
+};
+
+static int state_machine = -1;
+static thread_reference_t tx_thread = NULL;
+
+#define BUFFER_SIZE 32
+static input_buffers_queue_t pio_rx_queue;
+static __attribute__((aligned(4))) uint8_t pio_rx_buffer[BQ_BUFFER_SIZE(BUFFER_SIZE, sizeof(uint32_t))];
+
+uint8_t ps2_error = PS2_ERR_NONE;
+
+void pio_serve_interrupt(void) {
+ uint32_t irqs = pio->ints0;
+
+ if (irqs & (PIO_IRQ0_INTF_SM0_RXNEMPTY_BITS << state_machine)) {
+ osalSysLockFromISR();
+ uint32_t* frame_buffer = (uint32_t*)ibqGetEmptyBufferI(&pio_rx_queue);
+ if (frame_buffer == NULL) {
+ osalSysUnlockFromISR();
+ return;
+ }
+ *frame_buffer = pio_sm_get(pio, state_machine);
+ ibqPostFullBufferI(&pio_rx_queue, sizeof(uint32_t));
+ osalSysUnlockFromISR();
+ }
+
+ if (irqs & (PIO_IRQ0_INTF_SM0_TXNFULL_BITS << state_machine)) {
+ pio_set_irq0_source_enabled(pio, pis_sm0_tx_fifo_not_full + state_machine, false);
+ osalSysLockFromISR();
+ osalThreadResumeI(&tx_thread, MSG_OK);
+ osalSysUnlockFromISR();
+ }
+}
+
+void ps2_host_init(void) {
+ ibqObjectInit(&pio_rx_queue, false, pio_rx_buffer, sizeof(uint32_t), BUFFER_SIZE, NULL, NULL);
+ uint pio_idx = pio_get_index(pio);
+
+ hal_lld_peripheral_unreset(pio_idx == 0 ? RESETS_ALLREG_PIO0 : RESETS_ALLREG_PIO1);
+
+ state_machine = pio_claim_unused_sm(pio, true);
+ if (state_machine < 0) {
+ dprintln("ERROR: Failed to acquire state machine for PS/2!");
+ ps2_error = PS2_ERR_NODATA;
+ return;
+ }
+
+ uint offset = pio_add_program(pio, &ps2_program);
+
+ pio_sm_config c = pio_get_default_sm_config();
+ sm_config_set_wrap(&c, offset + PS2_WRAP_TARGET, offset + PS2_WRAP);
+
+ // Set pindirs to input (output enable is inverted below)
+ pio_sm_set_consecutive_pindirs(pio, state_machine, PS2_DATA_PIN, 2, true);
+ sm_config_set_clkdiv(&c, (float)clock_get_hz(clk_sys) / (200.0f * KHZ));
+ sm_config_set_set_pins(&c, PS2_DATA_PIN, 2);
+ sm_config_set_out_pins(&c, PS2_DATA_PIN, 1);
+ sm_config_set_out_shift(&c, true, true, 10);
+ sm_config_set_in_shift(&c, true, true, 11);
+ sm_config_set_jmp_pin(&c, PS2_CLOCK_PIN);
+ sm_config_set_in_pins(&c, PS2_DATA_PIN);
+
+ // clang-format off
+ iomode_t pin_mode = PAL_RP_PAD_IE |
+ PAL_RP_GPIO_OE |
+ PAL_RP_PAD_SLEWFAST |
+ PAL_RP_PAD_DRIVE12 |
+ // Invert output enable so that pindirs=1 means input
+ // and indirs=0 means output. This way, out pindirs
+ // works correctly with the open-drain PS/2 interface.
+ // Setting pindirs=1 effectively pulls the line high,
+ // due to the pull-up resistor, while pindirs=0 pulls
+ // the line low.
+ PAL_RP_IOCTRL_OEOVER_DRVINVPERI |
+ (pio_idx == 0 ? PAL_MODE_ALTERNATE_PIO0 : PAL_MODE_ALTERNATE_PIO1);
+ // clang-format on
+
+ palSetLineMode(PS2_DATA_PIN, pin_mode);
+ palSetLineMode(PS2_CLOCK_PIN, pin_mode);
+
+ pio_set_irq0_source_enabled(pio, pis_sm0_rx_fifo_not_empty + state_machine, true);
+ pio_sm_init(pio, state_machine, offset, &c);
+
+#if defined(PS2_PIO_USE_PIO1)
+ nvicEnableVector(RP_PIO1_IRQ_0_NUMBER, CORTEX_MAX_KERNEL_PRIORITY);
+#else
+ nvicEnableVector(RP_PIO0_IRQ_0_NUMBER, CORTEX_MAX_KERNEL_PRIORITY);
+#endif
+
+ pio_sm_set_enabled(pio, state_machine, true);
+}
+
+static int bit_parity(int x) {
+ return !__builtin_parity(x);
+}
+
+uint8_t ps2_host_send(uint8_t data) {
+ uint32_t frame = 0b1000000000;
+ frame = frame | data;
+
+ if (bit_parity(data)) {
+ frame = frame | (1 << 8);
+ }
+
+ pio_sm_put(pio, state_machine, frame);
+
+ msg_t msg = MSG_OK;
+ osalSysLock();
+ while (pio_sm_is_tx_fifo_full(pio, state_machine)) {
+ pio_set_irq0_source_enabled(pio, pis_sm0_tx_fifo_not_full + state_machine, true);
+ msg = osalThreadSuspendTimeoutS(&tx_thread, TIME_MS2I(100));
+ if (msg < MSG_OK) {
+ pio_set_irq0_source_enabled(pio, pis_sm0_tx_fifo_not_full + state_machine, false);
+ ps2_error = PS2_ERR_NODATA;
+ osalSysUnlock();
+ return 0;
+ }
+ }
+ osalSysUnlock();
+
+ return ps2_host_recv_response();
+}
+
+static uint8_t ps2_get_data_from_frame(uint32_t frame) {
+ uint8_t data = (frame >> 22) & 0xFF;
+ uint32_t start_bit = (frame & 0b00000000001000000000000000000000) ? 1 : 0;
+ uint32_t parity_bit = (frame & 0b01000000000000000000000000000000) ? 1 : 0;
+ uint32_t stop_bit = (frame & 0b10000000001000000000000000000000) ? 1 : 0;
+
+ if (start_bit != 0) {
+ ps2_error = PS2_ERR_STARTBIT1;
+ return 0;
+ }
+
+ if (parity_bit != bit_parity(data)) {
+ ps2_error = PS2_ERR_PARITY;
+ return 0;
+ }
+
+ if (stop_bit != 1) {
+ ps2_error = PS2_ERR_STARTBIT2;
+ return 0;
+ }
+
+ return data;
+}
+
+uint8_t ps2_host_recv_response(void) {
+ uint32_t frame = 0;
+ msg_t msg = MSG_OK;
+
+ msg = ibqReadTimeout(&pio_rx_queue, (uint8_t*)&frame, sizeof(uint32_t), TIME_MS2I(100));
+ if (msg < MSG_OK) {
+ ps2_error = PS2_ERR_NODATA;
+ return 0;
+ }
+
+ return ps2_get_data_from_frame(frame);
+}
+
+#ifdef BUFFERED_MODE_ENABLE
+
+bool pbuf_has_data(void) {
+ osalSysLock();
+ bool has_data = !ibqIsEmptyI(&pio_rx_queue);
+ osalSysUnlock();
+ return has_data;
+}
+
+uint8_t ps2_host_recv(void) {
+ uint32_t frame = 0;
+ msg_t msg = MSG_OK;
+
+ uint8_t has_data = pbuf_has_data();
+ if (has_data) {
+ msg = ibqReadTimeout(&pio_rx_queue, (uint8_t*)&frame, sizeof(uint32_t), TIME_MS2I(100));
+ if (msg < MSG_OK) {
+ ps2_error = PS2_ERR_NODATA;
+ return 0;
+ }
+ } else {
+ ps2_error = PS2_ERR_NODATA;
+ }
+
+ return frame != 0 ? ps2_get_data_from_frame(frame) : 0;
+}
+
+#endif
diff --git a/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c b/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c
index a46b099195..99a6cfaba9 100644
--- a/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c
+++ b/platforms/chibios/drivers/vendor/RP/RP2040/ws2812_vendor.c
@@ -185,7 +185,7 @@ bool ws2812_init(void) {
(pio_idx == 0 ? PAL_MODE_ALTERNATE_PIO0 : PAL_MODE_ALTERNATE_PIO1);
// clang-format on
- palSetLineMode(RGB_DI_PIN, rgb_pin_mode);
+ palSetLineMode(WS2812_DI_PIN, rgb_pin_mode);
STATE_MACHINE = pio_claim_unused_sm(pio, true);
if (STATE_MACHINE < 0) {
@@ -195,11 +195,11 @@ bool ws2812_init(void) {
uint offset = pio_add_program(pio, &ws2812_program);
- pio_sm_set_consecutive_pindirs(pio, STATE_MACHINE, RGB_DI_PIN, 1, true);
+ pio_sm_set_consecutive_pindirs(pio, STATE_MACHINE, WS2812_DI_PIN, 1, true);
pio_sm_config config = pio_get_default_sm_config();
sm_config_set_wrap(&config, offset + WS2812_WRAP_TARGET, offset + WS2812_WRAP);
- sm_config_set_sideset_pins(&config, RGB_DI_PIN);
+ sm_config_set_sideset_pins(&config, WS2812_DI_PIN);
sm_config_set_fifo_join(&config, PIO_FIFO_JOIN_TX);
#if defined(WS2812_EXTERNAL_PULLUP)
diff --git a/platforms/chibios/drivers/ws2812.c b/platforms/chibios/drivers/ws2812_bitbang.c
index 55ac333b1e..d05deb1a50 100644
--- a/platforms/chibios/drivers/ws2812.c
+++ b/platforms/chibios/drivers/ws2812_bitbang.c
@@ -53,22 +53,22 @@ void sendByte(uint8_t byte) {
// using something like wait_ns(is_one ? T1L : T0L) here throws off timings
if (is_one) {
// 1
- writePinHigh(RGB_DI_PIN);
+ writePinHigh(WS2812_DI_PIN);
wait_ns(WS2812_T1H);
- writePinLow(RGB_DI_PIN);
+ writePinLow(WS2812_DI_PIN);
wait_ns(WS2812_T1L);
} else {
// 0
- writePinHigh(RGB_DI_PIN);
+ writePinHigh(WS2812_DI_PIN);
wait_ns(WS2812_T0H);
- writePinLow(RGB_DI_PIN);
+ writePinLow(WS2812_DI_PIN);
wait_ns(WS2812_T0L);
}
}
}
void ws2812_init(void) {
- palSetLineMode(RGB_DI_PIN, WS2812_OUTPUT_MODE);
+ palSetLineMode(WS2812_DI_PIN, WS2812_OUTPUT_MODE);
}
// Setleds for standard RGB
diff --git a/platforms/chibios/drivers/ws2812_pwm.c b/platforms/chibios/drivers/ws2812_pwm.c
index c4a591c10b..04c8279a97 100644
--- a/platforms/chibios/drivers/ws2812_pwm.c
+++ b/platforms/chibios/drivers/ws2812_pwm.c
@@ -308,7 +308,7 @@ void ws2812_init(void) {
for (i = 0; i < WS2812_RESET_BIT_N; i++)
ws2812_frame_buffer[i + WS2812_COLOR_BIT_N] = 0; // All reset bits are zero
- palSetLineMode(RGB_DI_PIN, WS2812_OUTPUT_MODE);
+ palSetLineMode(WS2812_DI_PIN, WS2812_OUTPUT_MODE);
// PWM Configuration
//#pragma GCC diagnostic ignored "-Woverride-init" // Turn off override-init warning for this struct. We use the overriding ability to set a "default" channel config
diff --git a/platforms/chibios/drivers/ws2812_spi.c b/platforms/chibios/drivers/ws2812_spi.c
index 03ffbd7f82..c28f5007f1 100644
--- a/platforms/chibios/drivers/ws2812_spi.c
+++ b/platforms/chibios/drivers/ws2812_spi.c
@@ -136,7 +136,7 @@ static void set_led_color_rgb(LED_TYPE color, int pos) {
}
void ws2812_init(void) {
- palSetLineMode(RGB_DI_PIN, WS2812_MOSI_OUTPUT_MODE);
+ palSetLineMode(WS2812_DI_PIN, WS2812_MOSI_OUTPUT_MODE);
#ifdef WS2812_SPI_SCK_PIN
palSetLineMode(WS2812_SPI_SCK_PIN, WS2812_SCK_OUTPUT_MODE);
@@ -150,8 +150,8 @@ void ws2812_init(void) {
WS2812_SPI_BUFFER_MODE,
# endif
NULL, // end_cb
- PAL_PORT(RGB_DI_PIN),
- PAL_PAD(RGB_DI_PIN),
+ PAL_PORT(WS2812_DI_PIN),
+ PAL_PAD(WS2812_DI_PIN),
# if defined(WB32F3G71xx) || defined(WB32FQ95xx)
0,
0,
@@ -170,8 +170,8 @@ void ws2812_init(void) {
# endif
NULL, // data_cb
NULL, // error_cb
- PAL_PORT(RGB_DI_PIN),
- PAL_PAD(RGB_DI_PIN),
+ PAL_PORT(WS2812_DI_PIN),
+ PAL_PAD(WS2812_DI_PIN),
WS2812_SPI_DIVISOR_CR1_BR_X,
0
#endif
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 05:47:20 +0000