diff options
Diffstat (limited to 'layouts/community/split_3x6_3/drashna/config.h')
| -rw-r--r-- | layouts/community/split_3x6_3/drashna/config.h | 43 |
1 files changed, 22 insertions, 21 deletions
diff --git a/layouts/community/split_3x6_3/drashna/config.h b/layouts/community/split_3x6_3/drashna/config.h index dd950ce7bc..b86448c671 100644 --- a/layouts/community/split_3x6_3/drashna/config.h +++ b/layouts/community/split_3x6_3/drashna/config.h @@ -31,11 +31,11 @@ #ifdef RGBLIGHT_ENABLE # undef RGBLED_NUM -# define RGBLED_NUM 27 +# define RGBLED_NUM 27 -# define RGBLIGHT_HUE_STEP 8 -# define RGBLIGHT_SAT_STEP 8 -# define RGBLIGHT_VAL_STEP 5 +# define RGBLIGHT_HUE_STEP 8 +# define RGBLIGHT_SAT_STEP 8 +# define RGBLIGHT_VAL_STEP 5 # define RGBLIGHT_LIMIT_VAL 120 #endif @@ -44,37 +44,38 @@ # undef RGB_DI_PIN # define RGB_DI_PIN A3 # endif -# define RGB_MATRIX_KEYPRESSES // reacts to keypresses +# define RGB_MATRIX_KEYPRESSES // reacts to keypresses // # define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (instead of keypresses) // # define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects -# define RGB_DISABLE_WHEN_USB_SUSPENDED true // turn off effects when suspended +# define RGB_DISABLE_WHEN_USB_SUSPENDED // turn off effects when suspended // # define RGB_MATRIX_LED_PROCESS_LIMIT (DRIVER_LED_TOTAL + 4) / 5 // limits the number of LEDs to process in an animation per task run (increases keyboard responsiveness) // # define RGB_MATRIX_LED_FLUSH_LIMIT 16 // limits in milliseconds how frequently an animation will update the LEDs. 16 (16ms) is equivalent to limiting to 60fps (increases keyboard responsiveness) -# define RGB_MATRIX_MAXIMUM_BRIGHTNESS 120 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255 -# define RGB_MATRIX_HUE_STEP 8 -# define RGB_MATRIX_SAT_STEP 8 -# define RGB_MATRIX_VAL_STEP 5 -# define RGB_MATRIX_SPD_STEP 10 +# ifndef RGB_MATRIX_MAXIMUM_BRIGHTNESS +# define RGB_MATRIX_MAXIMUM_BRIGHTNESS 120 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255 +# endif +# define RGB_MATRIX_HUE_STEP 8 +# define RGB_MATRIX_SAT_STEP 8 +# define RGB_MATRIX_VAL_STEP 5 +# define RGB_MATRIX_SPD_STEP 10 #endif #ifdef CONVERT_TO_PROTON_C -# define WS2812_PWM_DRIVER PWMD2 // default: PWMD2 -# define WS2812_PWM_CHANNEL 4 // default: 2 -# define WS2812_PWM_PAL_MODE 1 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2 -# define WS2812_DMA_STREAM STM32_DMA1_STREAM2 // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. -# define WS2812_DMA_CHANNEL 2 // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. -# define WS2812_DMAMUX_ID STM32_DMAMUX1_TIM2_UP // DMAMUX configuration for TIMx_UP -- only required if your MCU has a DMAMUX peripheral, see the respective reference manual for the appropriate values for your MCU. +# define WS2812_PWM_DRIVER PWMD2 // default: PWMD2 +# define WS2812_PWM_CHANNEL 4 // default: 2 +# define WS2812_PWM_PAL_MODE 1 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2 +# define WS2812_DMA_STREAM STM32_DMA1_STREAM2 // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. +# define WS2812_DMA_CHANNEL 2 // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. +# define WS2812_DMAMUX_ID STM32_DMAMUX1_TIM2_UP // DMAMUX configuration for TIMx_UP -- only required if your MCU has a DMAMUX peripheral, see the respective reference manual for the appropriate values for your MCU. # undef SOFT_SERIAL_PIN -# define SOFT_SERIAL_PIN D3 -# define SERIAL_USART_DRIVER SD1 // USART driver of TX pin. default: SD1 -# define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7 +# define SOFT_SERIAL_PIN D3 +# define SERIAL_USART_DRIVER SD1 // USART driver of TX pin. default: SD1 +# define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7 // #define INIT_EE_HANDS_LEFT // #define INIT_EE_HANDS_RIGHT #endif - #if defined(AUDIO_ENABLE) && !defined(CONVERT_TO_PROTON_C) # define AUDIO_PIN B6 # define NO_MUSIC_MODE |