summaryrefslogtreecommitdiff
path: root/keyboards/zinc
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/zinc')
-rw-r--r--keyboards/zinc/keymaps/default/rules.mk1
-rw-r--r--keyboards/zinc/rules.mk53
2 files changed, 11 insertions, 43 deletions
diff --git a/keyboards/zinc/keymaps/default/rules.mk b/keyboards/zinc/keymaps/default/rules.mk
index 2dcefc0016..d2bc96e3af 100644
--- a/keyboards/zinc/keymaps/default/rules.mk
+++ b/keyboards/zinc/keymaps/default/rules.mk
@@ -1,4 +1,3 @@
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
diff --git a/keyboards/zinc/rules.mk b/keyboards/zinc/rules.mk
index 7574af387c..d9d840c2d0 100644
--- a/keyboards/zinc/rules.mk
+++ b/keyboards/zinc/rules.mk
@@ -1,50 +1,16 @@
-#SRC += i2c.c
-SRC += serial.c
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-# This definition is optional, and if your keyboard supports multiple bootloaders of
-# different sizes, comment this out, and the correct address will be loaded
-# automatically (+60). See bootloader.mk for all options.
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = caterina
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
@@ -69,3 +35,6 @@ SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
CUSTOM_MATRIX = yes
DEFAULT_FOLDER = zinc/rev1
+
+#SRC += i2c.c
+SRC += serial.c