summaryrefslogtreecommitdiff
path: root/keyboards/wilba_tech/wt60_a
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/wilba_tech/wt60_a')
-rw-r--r--keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk2
-rw-r--r--keyboards/wilba_tech/wt60_a/rules.mk61
2 files changed, 16 insertions, 47 deletions
diff --git a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk
index 8834bf0c8e..4880a57bec 100644
--- a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk
+++ b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk
@@ -1,2 +1,2 @@
RAW_ENABLE = yes
-DYNAMIC_KEYMAP_ENABLE = yes \ No newline at end of file
+DYNAMIC_KEYMAP_ENABLE = yes
diff --git a/keyboards/wilba_tech/wt60_a/rules.mk b/keyboards/wilba_tech/wt60_a/rules.mk
index 4f702fab49..111c94ee80 100644
--- a/keyboards/wilba_tech/wt60_a/rules.mk
+++ b/keyboards/wilba_tech/wt60_a/rules.mk
@@ -1,54 +1,16 @@
-# project specific files
-SRC = drivers/issi/is31fl3736.c \
- drivers/avr/i2c_master.c \
- quantum/color.c \
- keyboards/wilba_tech/wt_mono_backlight.c \
- keyboards/wilba_tech/wt_main.c
-
# MCU name
MCU = atmega32u4
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section
+# Bootloader selection
+# Teensy halfkay
+# Pro Micro caterina
+# Atmel DFU atmel-dfu
+# LUFA DFU lufa-dfu
+# QMK DFU qmk-dfu
+# ATmega32A bootloadHID
+# ATmega328P USBasp
BOOTLOADER = atmel-dfu
-
# Build Options
# change yes to no to disable
#
@@ -67,3 +29,10 @@ UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+
+# project specific files
+SRC = drivers/issi/is31fl3736.c \
+ drivers/avr/i2c_master.c \
+ quantum/color.c \
+ keyboards/wilba_tech/wt_mono_backlight.c \
+ keyboards/wilba_tech/wt_main.c