diff options
Diffstat (limited to 'keyboards/satan')
| -rw-r--r-- | keyboards/satan/Makefile | 70 | ||||
| -rw-r--r-- | keyboards/satan/config.h | 94 | ||||
| -rw-r--r-- | keyboards/satan/controller.jpg | bin | 0 -> 140199 bytes | |||
| -rw-r--r-- | keyboards/satan/keymaps/default/keymap.c | 162 | ||||
| -rw-r--r-- | keyboards/satan/keymaps/sethbc/keymap.c | 149 | ||||
| -rw-r--r-- | keyboards/satan/pinout.txt | 1 | ||||
| -rw-r--r-- | keyboards/satan/power.jpg | bin | 0 -> 433947 bytes | |||
| -rw-r--r-- | keyboards/satan/satan.c | 30 | ||||
| -rw-r--r-- | keyboards/satan/satan.h | 69 |
9 files changed, 575 insertions, 0 deletions
diff --git a/keyboards/satan/Makefile b/keyboards/satan/Makefile new file mode 100644 index 0000000000..184b5ac372 --- /dev/null +++ b/keyboards/satan/Makefile @@ -0,0 +1,70 @@ + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE ?= yes # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID + +ifndef QUANTUM_DIR + include ../../Makefile +endif diff --git a/keyboards/satan/config.h b/keyboards/satan/config.h new file mode 100644 index 0000000000..a7ea8f904c --- /dev/null +++ b/keyboards/satan/config.h @@ -0,0 +1,94 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0003 +#define MANUFACTURER SATAN +#define PRODUCT GH60 +#define DESCRIPTION QMK keyboard firmware for Satan GH60 with WS2812 support + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +// ROWS: Top to bottom, COLS: Left to right + +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B7, D4, B1, B0, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +#define BACKLIGHT_PIN B6 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* Backlight configuration + */ +#define BACKLIGHT_LEVELS 4 + +/* Underlight configuration + */ + #define ws2812_PORTREG PORTE + #define ws2812_DDRREG DDRE + #define ws2812_pin 2 + #define RGBLED_NUM 8 // Number of LEDs + #define RGBLIGHT_HUE_STEP 10 + #define RGBLIGHT_SAT_STEP 17 + #define RGBLIGHT_VAL_STEP 17 + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/satan/controller.jpg b/keyboards/satan/controller.jpg Binary files differnew file mode 100644 index 0000000000..76ffa45004 --- /dev/null +++ b/keyboards/satan/controller.jpg diff --git a/keyboards/satan/keymaps/default/keymap.c b/keyboards/satan/keymaps/default/keymap.c new file mode 100644 index 0000000000..b19404afc7 --- /dev/null +++ b/keyboards/satan/keymaps/default/keymap.c @@ -0,0 +1,162 @@ +#include "satan.h" + +#ifdef RGBLIGHT_ENABLE +#include "rgblight.h" +#endif + +// Used for SHIFT_ESC +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-----------------------------------------------------------. + * |Esc~| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp | + * |-----------------------------------------------------------| + * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \ | + * |-----------------------------------------------------------| + * |CAPS | A| S| D| F| G| H| J| K| L| ;| '|Return | + * |-----------------------------------------------------------| + * |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift | + * |-----------------------------------------------------------| + * |Ctrl|Gui |Alt | Space |Alt |Gui |FN |Ctrl | + * `-----------------------------------------------------------' + */ +[_BL] = KEYMAP( + F(0), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, \ + KC_LCTL, KC_LGUI,KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(_FL), KC_RCTL), + + /* Keymap _FL: Function Layer + * ,-----------------------------------------------------------. + * | | | | | | | | | | | | | | RESET| + * |-----------------------------------------------------------| + * | | | | | | | | | | | |BL-|BL+|BL | + * |-----------------------------------------------------------| + * | | | | | | | | | | | | | + * |-----------------------------------------------------------| + * | | F1|F2 | F3|F4 | F5| F6| F7| F8| | | | + * |-----------------------------------------------------------| + * | | | | | | | | | + * `-----------------------------------------------------------' + */ +[_FL] = KEYMAP( + #ifdef RGBLIGHT_ENABLE + KC_GRV, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET, \ + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC, BL_INC, BL_TOGG, \ + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, F(1), F(2), F(3), F(4), F(5), F(6), F(7), F(8), KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + #else + KC_GRV, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET, \ + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC, BL_INC, BL_TOGG, \ + KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + #endif +}; + +enum function_id { + SHIFT_ESC, + #ifdef RGBLIGHT_ENABLE + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL + #endif +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_FUNCTION(SHIFT_ESC), + #ifdef RGBLIGHT_ENABLE + [1] = ACTION_FUNCTION(RGBLED_TOGGLE), + [2] = ACTION_FUNCTION(RGBLED_STEP_MODE), + [3] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [4] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [5] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [6] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [7] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [8] = ACTION_FUNCTION(RGBLED_DECREASE_VAL), + #endif +}; + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + static uint8_t shift_esc_shift_mask; + switch (id) { + case SHIFT_ESC: + shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; + if (record->event.pressed) { + if (shift_esc_shift_mask) { + add_key(KC_GRV); + send_keyboard_report(); + } else { + add_key(KC_ESC); + send_keyboard_report(); + } + } else { + if (shift_esc_shift_mask) { + del_key(KC_GRV); + send_keyboard_report(); + } else { + del_key(KC_ESC); + send_keyboard_report(); + } + } + break; + //led operations + #ifdef RGBLIGHT_ENABLE + case RGBLED_TOGGLE: + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + #endif + } +} diff --git a/keyboards/satan/keymaps/sethbc/keymap.c b/keyboards/satan/keymaps/sethbc/keymap.c new file mode 100644 index 0000000000..0ea4a7ae4f --- /dev/null +++ b/keyboards/satan/keymaps/sethbc/keymap.c @@ -0,0 +1,149 @@ +#include "satan.h" + +#ifdef RGBLIGHT_ENABLE +#include "rgblight.h" +#endif + +// Used for SHIFT_ESC +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-----------------------------------------------------------. + * |Esc~| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =| \ | ~ | + * |-----------------------------------------------------------| + * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]|bksp | + * |-----------------------------------------------------------| + * |CAPS | A| S| D| F| G| H| J| K| L| ;| '|Return | + * |-----------------------------------------------------------| + * |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift| fn | + * |-----------------------------------------------------------| + * |Ctrl|Gui |Alt | Space |Alt |Gui |FN |Ctrl | + * `-----------------------------------------------------------' + */ +[_BL] = KEYMAP_HHKB( + F(0), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_GRV, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, \ + KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(_FL), \ + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, KC_MENU, KC_RCTL), + +[_FL] = KEYMAP_HHKB( + #ifdef RGBLIGHT_ENABLE + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, RESET, \ + KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, KC_TRNS, KC_BSPC, \ + KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_TRNS, KC_TRNS, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, KC_PENT, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + #else + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_TRNS, RESET, \ + KC_CAPS, KC_TRNS, F(1), F(2), F(3), KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, KC_TRNS, KC_BSPC, \ + KC_TRNS, KC_VOLD, F(4), F(5), F(6), KC_TRNS, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, KC_PENT, \ + KC_TRNS, F(7), F(8), KC_TRNS, KC_TRNS, KC_TRNS, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + #endif +}; + +enum function_id { + SHIFT_ESC, + #ifdef RGBLIGHT_ENABLE + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL + #endif +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_FUNCTION(SHIFT_ESC), + #ifdef RGBLIGHT_ENABLE + [1] = ACTION_FUNCTION(RGBLED_TOGGLE), + [2] = ACTION_FUNCTION(RGBLED_STEP_MODE), + [3] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [4] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [5] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [6] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [7] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [8] = ACTION_FUNCTION(RGBLED_DECREASE_VAL), + #endif +}; + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + static uint8_t shift_esc_shift_mask; + switch (id) { + case SHIFT_ESC: + shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; + if (record->event.pressed) { + if (shift_esc_shift_mask) { + add_key(KC_GRV); + send_keyboard_report(); + } else { + add_key(KC_ESC); + send_keyboard_report(); + } + } else { + if (shift_esc_shift_mask) { + del_key(KC_GRV); + send_keyboard_report(); + } else { + del_key(KC_ESC); + send_keyboard_report(); + } + } + break; + //led operations + #ifdef RGBLIGHT_ENABLE + case RGBLED_TOGGLE: + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + #endif + } +} diff --git a/keyboards/satan/pinout.txt b/keyboards/satan/pinout.txt new file mode 100644 index 0000000000..d1ad4ac883 --- /dev/null +++ b/keyboards/satan/pinout.txt @@ -0,0 +1 @@ +For WS2812B LED strip support, connect DIN from strip to PE2 on ATmega32u4 controller (see reference image controller.jpg)
\ No newline at end of file diff --git a/keyboards/satan/power.jpg b/keyboards/satan/power.jpg Binary files differnew file mode 100644 index 0000000000..0514eef5c7 --- /dev/null +++ b/keyboards/satan/power.jpg diff --git a/keyboards/satan/satan.c b/keyboards/satan/satan.c new file mode 100644 index 0000000000..d2c5d5c205 --- /dev/null +++ b/keyboards/satan/satan.c @@ -0,0 +1,30 @@ +#include "satan.h" +#include "led.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + matrix_init_user(); + led_init_ports(); +}; + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + matrix_scan_user(); +}; + +void led_init_ports(void) { + // * Set our LED pins as output + DDRB |= (1<<2); +} + +void led_set_kb(uint8_t usb_led) { + if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + // Turn capslock on + PORTB &= ~(1<<2); + } else { + // Turn capslock off + PORTB |= (1<<2); + } +} diff --git a/keyboards/satan/satan.h b/keyboards/satan/satan.h new file mode 100644 index 0000000000..fa17119150 --- /dev/null +++ b/keyboards/satan/satan.h @@ -0,0 +1,69 @@ +#ifndef SATAN_H +#define SATAN_H + +#include "quantum.h" + +/* Clueboard matrix layout + * ,-----------------------------------------------------------. + * | 00 |01| 02| 03| 04| 05| 06| 07| 08| 09| 0a| 0b| 0c| 0d | + * |-----------------------------------------------------------| + * | 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1a| 1b| 1c| 1d | + * |-----------------------------------------------------------| + * | 20 | 21| 22| 23| 24| 25| 26| 27| 28| 29| 2a| 2b| 2d | + * |-----------------------------------------------------------| + * | 30 | 32| 33| 34| 35| 36| 37| 38| 39| 3a| 3b| 3d | + * |-----------------------------------------------------------| + * | 40 | 41 | 42 | 45 | 4a | 4b | 4c | 4d | + * `-----------------------------------------------------------' + */ +// The first section contains all of the arguments +// The second converts the arguments into a two-dimensional array +#define KEYMAP( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2d, \ + k30, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3d, \ + k40, k41, k42, k45, k4a, k4b, k4c, k4d \ +) \ +{ \ + {k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d}, \ + {k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d}, \ + {k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, KC_NO, k2d}, \ + {k30, KC_NO, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, KC_NO, k3d}, \ + {k40, k41, k42, KC_NO, KC_NO, k45, KC_NO, KC_NO, KC_NO, KC_NO, k4a, k4b, k4c, k4d} \ +} + +/* Satan HHKB matrix layout + * ,------------------------------------------------------------. + * | 00 |01| 02| 03| 04| 05| 06| 07| 08| 09| 0a| 0b| 0c| 0d| 49 | + * |------------------------------------------------------------| + * | 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1a| 1b| 1c| 1d | + * |------------------------------------------------------------| + * | 20 | 21| 22| 23| 24| 25| 26| 27| 28| 29| 2a| 2b| 2d | + * |------------------------------------------------------------| + * | 30 | 32| 33| 34| 35| 36| 37| 38| 39| 3a| 3b| 3d | 3c | + * |------------------------------------------------------------| + * | 40 | 41 | 42 | 45 | 4a | 4b | 4c | 4d | + * `------------------------------------------------------------' + */ + +#define KEYMAP_HHKB( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d, k49, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2d, \ + k30, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3d, k3c, \ + k40, k41, k42, k45, k4a, k4b, k4c, k4d \ +) \ +{ \ + {k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, k0d}, \ + {k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, k1d}, \ + {k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, KC_NO, k2d}, \ + {k30, KC_NO, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, k3c, k3d}, \ + {k40, k41, k42, KC_NO, KC_NO, k45, KC_NO, KC_NO, KC_NO, k49, k4a, k4b, k4c, k4d} \ +} + + +void matrix_init_user(void); +void matrix_scan_user(void); + +#endif |
