diff options
Diffstat (limited to 'keyboards/preonic')
| -rw-r--r-- | keyboards/preonic/Makefile | 73 | ||||
| -rw-r--r-- | keyboards/preonic/config.h | 91 | ||||
| -rw-r--r-- | keyboards/preonic/keymaps/default/Makefile | 25 | ||||
| -rw-r--r-- | keyboards/preonic/keymaps/default/keymap.c | 280 | ||||
| -rw-r--r-- | keyboards/preonic/keymaps/default/readme.md | 1 | ||||
| -rw-r--r-- | keyboards/preonic/preonic.c | 10 | ||||
| -rw-r--r-- | keyboards/preonic/preonic.h | 36 | ||||
| -rw-r--r-- | keyboards/preonic/readme.md | 25 |
8 files changed, 541 insertions, 0 deletions
diff --git a/keyboards/preonic/Makefile b/keyboards/preonic/Makefile new file mode 100644 index 0000000000..08e9205cbf --- /dev/null +++ b/keyboards/preonic/Makefile @@ -0,0 +1,73 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/preonic/config.h b/keyboards/preonic/config.h new file mode 100644 index 0000000000..04946f7fbb --- /dev/null +++ b/keyboards/preonic/config.h @@ -0,0 +1,91 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6061 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Ortholinear Keyboards +#define PRODUCT The Preonic Keyboard +#define DESCRIPTION A compact ortholinear keyboard + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 12 + +/* Planck PCB default pin-out */ +#define MATRIX_ROW_PINS { D2, D5, B5, B6, D3 } +#define MATRIX_COL_PINS { F1, F0, B0, C7, F4, F5, F6, F7, D4, D6, B4, D7 } +#define UNUSED_PINS + +#define BACKLIGHT_PIN B7 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* ws2812 RGB LED */ +#define ws2812_PORTREG PORTD +#define ws2812_DDRREG DDRD +#define ws2812_pin PD1 +#define RGBLED_NUM 28 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +// #define NO_DEBUG + +/* disable print */ +// #define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/preonic/keymaps/default/Makefile b/keyboards/preonic/keymaps/default/Makefile new file mode 100644 index 0000000000..581e08cd02 --- /dev/null +++ b/keyboards/preonic/keymaps/default/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = yes # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/preonic/keymaps/default/keymap.c b/keyboards/preonic/keymaps/default/keymap.c new file mode 100644 index 0000000000..9a957f7ee1 --- /dev/null +++ b/keyboards/preonic/keymaps/default/keymap.c @@ -0,0 +1,280 @@ +#include "preonic.h" +#include "action_layer.h" +#include "eeconfig.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _COLEMAK 1 +#define _DVORAK 2 +#define _LOWER 3 +#define _RAISE 4 +#define _ADJUST 16 + +enum preonic_keycodes { + QWERTY = SAFE_RANGE, + COLEMAK, + DVORAK, + LOWER, + RAISE, + BACKLIT +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC}, + {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL}, + {KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, + {BACKLIT, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Colemak + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Tab | Q | W | F | P | G | J | L | U | Y | ; | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | R | S | T | D | H | N | E | I | O | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | K | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_COLEMAK] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC}, + {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_DEL}, + {KC_ESC, KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT}, + {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT }, + {BACKLIT, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Dvorak + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Tab | " | , | . | P | Y | F | G | C | R | L | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | O | E | U | I | D | H | T | N | S | / | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| ; | Q | J | K | X | B | M | W | V | Z |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_DVORAK] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC}, + {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_DEL}, + {KC_ESC, KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_SLSH}, + {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_ENT }, + {BACKLIT, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO ~ |ISO | | | |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = { + {KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC}, + {KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL}, + {KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE}, + {_______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12,S(KC_NUHS),S(KC_NUBS),_______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY} +}, + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | - | = | [ | ] | \ | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO # |ISO / | | |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC}, + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL}, + {KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS}, + {_______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_NUHS, KC_NUBS, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY} +}, + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | Reset| | | | | | | | | | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | |Audoff|Aud on|AGnorm|AGswap|Qwerty|Colemk|Dvorak| | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | |Voice-|Voice+|Musoff|Mus on| | | | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = { + {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12}, + {_______, RESET, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_DEL}, + {_______, _______, _______, AU_ON, AU_OFF, AG_NORM, AG_SWAP, QWERTY, COLEMAK, DVORAK, _______, _______}, + {_______, MUV_DE, MUV_IN, MU_ON, MU_OFF, MI_ON, MI_OFF, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +} + + +}; + +#ifdef AUDIO_ENABLE +float tone_startup[][2] = { + {NOTE_B5, 20}, + {NOTE_B6, 8}, + {NOTE_DS6, 20}, + {NOTE_B6, 8} +}; + +float tone_qwerty[][2] = SONG(QWERTY_SOUND); +float tone_dvorak[][2] = SONG(DVORAK_SOUND); +float tone_colemak[][2] = SONG(COLEMAK_SOUND); + +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); + +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); +#endif + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + persistant_default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case COLEMAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_colemak, false, 0); + #endif + persistant_default_layer_set(1UL<<_COLEMAK); + } + return false; + break; + case DVORAK: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_dvorak, false, 0); + #endif + persistant_default_layer_set(1UL<<_DVORAK); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case BACKLIT: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + return false; + break; + } + return true; +}; + +void matrix_init_user(void) { + #ifdef AUDIO_ENABLE + startup_user(); + #endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif
\ No newline at end of file diff --git a/keyboards/preonic/keymaps/default/readme.md b/keyboards/preonic/keymaps/default/readme.md new file mode 100644 index 0000000000..e911968dd9 --- /dev/null +++ b/keyboards/preonic/keymaps/default/readme.md @@ -0,0 +1 @@ +# The default Preonic layout - largely based on the Planck's
\ No newline at end of file diff --git a/keyboards/preonic/preonic.c b/keyboards/preonic/preonic.c new file mode 100644 index 0000000000..889c3fc8fd --- /dev/null +++ b/keyboards/preonic/preonic.c @@ -0,0 +1,10 @@ +#include "preonic.h" + +void matrix_init_kb(void) { + + // Turn status LED on + DDRE |= (1<<6); + PORTE |= (1<<6); + + matrix_init_user(); +};
\ No newline at end of file diff --git a/keyboards/preonic/preonic.h b/keyboards/preonic/preonic.h new file mode 100644 index 0000000000..0e0b101e45 --- /dev/null +++ b/keyboards/preonic/preonic.h @@ -0,0 +1,36 @@ +#ifndef PREONIC_H +#define PREONIC_H + +#include "quantum.h" + +#define PREONIC_MIT( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \ + k40, k41, k42, k43, k44, k45, k47, k48, k49, k4a, k4b \ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \ + { k30, k31, k32, k33, k34, k35, k35, k37, k38, k39, k3a, k3b }, \ + { k40, k41, k42, k43, k44, k45, k45, k47, k48, k49, k4a, k4b } \ +} + +#define PREONIC_GRID( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \ + k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b \ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \ + { k30, k31, k32, k33, k34, k35, k35, k37, k38, k39, k3a, k3b }, \ + { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b } \ +} + +#endif diff --git a/keyboards/preonic/readme.md b/keyboards/preonic/readme.md new file mode 100644 index 0000000000..f0be255a09 --- /dev/null +++ b/keyboards/preonic/readme.md @@ -0,0 +1,25 @@ +Preonic keyboard firmware +====================== +DIY/Assembled compact ortholinear 50% keyboard by [Ortholinear Keyboards](http://ortholinearkeyboards.com). + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/preonic folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap, create a file in the keymaps folder named `<name>.c` and see keymap document (you can find in top readme.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. |