5 files changed, 6 insertions, 13 deletions
diff --git a/keyboards/mechlovin/zed65/910/config.h b/keyboards/mechlovin/zed65/910/config.h
index a5902fa9c1..f21653f5af 100644
--- a/keyboards/mechlovin/zed65/910/config.h
+++ b/keyboards/mechlovin/zed65/910/config.h
@@ -17,5 +17,5 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #pragma once
 
-#define WS2812_SPI SPID1 // default: SPID1
+#define WS2812_SPI_DRIVER SPID1 // default: SPID1
 #define WS2812_SPI_MOSI_PAL_MODE 6 // MOSI pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 5
diff --git a/keyboards/mechlovin/zed65/mono_led/config.h b/keyboards/mechlovin/zed65/mono_led/config.h
index 1ec1746456..b5d737641b 100644
--- a/keyboards/mechlovin/zed65/mono_led/config.h
+++ b/keyboards/mechlovin/zed65/mono_led/config.h
@@ -18,18 +18,11 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #pragma once
 
 #ifdef LED_MATRIX_ENABLE
-// This is a 7-bit address, that gets left-shifted and bit 0
-// set to 0 for write, 1 for read (as per I2C protocol)
-// The address will vary depending on your wiring:
-// 0b1110100 AD <-> GND
-// 0b1110111 AD <-> VCC
-// 0b1110101 AD <-> SCL
-// 0b1110110 AD <-> SDA
-#define LED_DRIVER_ADDR_1 0b1110110
+#define IS31FL3731_I2C_ADDRESS_1 IS31FL3731_I2C_ADDRESS_SDA
 #define I2C_DRIVER I2CD2
 #define I2C1_SCL_PIN B10
 #define I2C1_SDA_PIN B11
-#define LED_DRIVER_COUNT 1
+#define IS31FL3731_DRIVER_COUNT 1
 #define LED_MATRIX_LED_COUNT 70
 #define LED_MATRIX_KEYPRESSES // reacts to keypresses
 #define LED_MATRIX_KEYRELEASES // reacts to keyreleases (instead of keypresses)
diff --git a/keyboards/mechlovin/zed65/mono_led/mono_led.c b/keyboards/mechlovin/zed65/mono_led/mono_led.c
index e618d41489..f66c4b1359 100644
--- a/keyboards/mechlovin/zed65/mono_led/mono_led.c
+++ b/keyboards/mechlovin/zed65/mono_led/mono_led.c
@@ -19,7 +19,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 
 
-const is31_led PROGMEM g_is31_leds[LED_MATRIX_LED_COUNT] = {
+const is31fl3731_led_t PROGMEM g_is31fl3731_leds[LED_MATRIX_LED_COUNT] = {
 /* Refer to IS31 manual for these locations
  *    driver
  *    |  LED address
diff --git a/keyboards/mechlovin/zed65/no_backlight/wearhaus66/config.h b/keyboards/mechlovin/zed65/no_backlight/wearhaus66/config.h
index 5cb2a00b88..3bec308941 100644
--- a/keyboards/mechlovin/zed65/no_backlight/wearhaus66/config.h
+++ b/keyboards/mechlovin/zed65/no_backlight/wearhaus66/config.h
@@ -17,5 +17,5 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #pragma once
 
-#define WS2812_SPI SPID2 // default: SPID1
+#define WS2812_SPI_DRIVER SPID2 // default: SPID1
 #define WS2812_SPI_MOSI_PAL_MODE 0 // MOSI pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 5
diff --git a/keyboards/mechlovin/zed65/rev1/config.h b/keyboards/mechlovin/zed65/rev1/config.h
index 24efedfffb..4ed1992992 100644
--- a/keyboards/mechlovin/zed65/rev1/config.h
+++ b/keyboards/mechlovin/zed65/rev1/config.h
@@ -18,7 +18,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #pragma once
 
 #ifdef RGBLIGHT_ENABLE
-#define WS2812_SPI SPID1 // default: SPID1
+#define WS2812_SPI_DRIVER SPID1 // default: SPID1
 #define WS2812_SPI_MOSI_PAL_MODE 6 // MOSI pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 5
 #define WS2812_SPI_USE_CIRCULAR_BUFFER
 #endif