summaryrefslogtreecommitdiff
path: root/keyboards/massdrop/ctrl/config.h
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/massdrop/ctrl/config.h')
-rw-r--r--keyboards/massdrop/ctrl/config.h30
1 files changed, 19 insertions, 11 deletions
diff --git a/keyboards/massdrop/ctrl/config.h b/keyboards/massdrop/ctrl/config.h
index 3dbd9b8877..b1df4452cc 100644
--- a/keyboards/massdrop/ctrl/config.h
+++ b/keyboards/massdrop/ctrl/config.h
@@ -42,6 +42,9 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
/* Temporary solution for matrix delay */
#define IGNORE_ATOMIC_BLOCK
+/* Avoid out-of-bounds errors when SmartEEPROM is not enabled */
+#define EEPROM_SIZE 1024
+
/* MCU Port name definitions */
#define PA 0
#define PB 1
@@ -49,22 +52,18 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
/* This Shift Register expands available hardware output lines to control additional peripherals */
/* It uses four lines from the MCU to provide 16 output lines */
/* Shift Register Clock configuration (MCU to ShiftRegister.RCLK) */
-#define SR_EXP_RCLK_PORT PB
-#define SR_EXP_RCLK_PIN 14
+#define SR_EXP_RCLK_PIN B14
/* Shift Register Output Enable configuration (MCU to ShiftRegister.OE_N) */
-#define SR_EXP_OE_N_PORT PB
-#define SR_EXP_OE_N_PIN 15
+#define SR_EXP_OE_PIN B15
/* SERCOM port to use for Shift Register SPI */
/* DATAOUT and SCLK must be configured to use hardware pins of this port */
-#define SR_EXP_SERCOM SERCOM2
+#define SPI_SERCOM SERCOM2
/* Shift Register SPI Data Out configuration (MCU.SERCOMx.PAD[0] to ShiftRegister.SER) */
-#define SR_EXP_DATAOUT_PORT PA
-#define SR_EXP_DATAOUT_PIN 12
-#define SR_EXP_DATAOUT_MUX 2
+#define SPI_DATAOUT_PIN A12
+#define SPI_DATAOUT_MUX 2
/* Shift Register SPI Serial Clock configuration (MCU.SERCOMx.PAD[1] to ShiftRegister.SRCLK) */
-#define SR_EXP_SCLK_PORT PA
-#define SR_EXP_SCLK_PIN 13
-#define SR_EXP_SCLK_MUX 2
+#define SPI_SCLK_PIN A13
+#define SPI_SCLK_MUX 2
/* Debug LED (Small LED Located near MCU) */
#define DEBUG_LED_ENABLE 1
@@ -93,6 +92,15 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
#define DEBUG_BOOT_TRACING_PORT PB
#define DEBUG_BOOT_TRACING_PIN 23
+/* USB2422 config */
+#define USB2422_ADDRESS 0x58
+#define USB2422_VENDOR_ID 0x04D8
+#define USB2422_PRODUCT_ID 0xEEC5
+#define USB2422_DEVICE_VER 0x0101
+#define USB2422_MANUFACTURER "Massdrop Inc."
+#define USB2422_PRODUCT "Massdrop Hub"
+#define USB2422_ACTIVE_PIN A18
+
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCE 5